REDLIGHTV4 Wi-Fi & Bluetooth Module Cover Letter Modular Approval Letter1x Buzz Products PTY LTD

Buzz Products PTY LTD Wi-Fi & Bluetooth Module

Page 1 of REDLIGHTV4 Wi-Fi & Bluetooth Module Cover Letter Modular Approval Letter1x Buzz Products PTY LTD
Page 2 of REDLIGHTV4 Wi-Fi & Bluetooth Module Cover Letter Modular Approval Letter1x Buzz Products PTY LTD
Page 3 of REDLIGHTV4 Wi-Fi & Bluetooth Module Cover Letter Modular Approval Letter1x Buzz Products PTY LTD

Company: Buzz Products PTY LTD
Add: 18 Studley Street Abbotsford Victoria Australia 3067
Tel:61384129000
Fax:61384129001
Applicant
FCC ID:
Buzz Products PTY LTD
2AA7C-REDLIGHTV4
Section 15.212 Modular Transmitters


Request for Modular Approval
Request for Limited Modular Approval

Requirements
EUT Conditions
Comply(Y/N)
Single Modular Approval Requirements
The radio elements of the modular Refer to external photos.
transmitter must have their own shielding.
The physical crystal and tuning capacitors
may be located external to the shielded
radio elements.
This module
shield cover.
The modular transmitter must have
buffered modulation/data inputs (if such
inputs are provided) to ensure that the
module will comply with part 15
requirements under conditions of
excessive data rates or over‐modulation.
All inputs to the modules
are buffered through logic
or microprocessor inputs.
Refer to Schematics.
The modular transmitter must have
its own power supply regulation.
The Module uses the chip
ESP32-DOWD with built-in
power management components,
the module reted power is 3.3V
power, Refer to schematics.
The modular transmitter must comply
with the antenna and transmission system
requirements of §§15.203, 15.204(b) and
15.204(c). The antenna must either be
permanently attached or employ a
“unique” antenna coupler (at all
connections between the module and the
antenna, including the cable). The
“professional installation” provision of
§15.203 is not applicable to modules but
can apply to limited modular approvals
under paragraph (b) of this section.
The modular
(ESP32-DOWD) transmitter
has a PCB antenna
arrangement for BT,BLE
and Wi-Fi, Refer to internal
photo.
does
have
5
The modular transmitter must be
tested in a stand‐alone configuration,
i.e., the module must not be inside
another device during testing for
compliance
with
part
15
requirements. Unless the transmitter
module will be battery powered, it
must comply with the AC line
conducted requirements found in
§15.207. AC or DC power lines and
data input/output lines connected to
the module must not contain
ferrites, unless they will be marketed
with the module (see §15.27(a)). The
length of these lines shall be the
length typical of actual use or, if that
length is unknown, at least 10
centimeters to insure that there is no
coupling between the case of the
module and supporting equipment.
Any accessories, peripherals, or
support equipment connected to the
module during testing shall be
unmodified
and
commercially
available (see §15.31(i)).
The modular transmitter
is connected to the
controlled board when
testing.
Please refer to setup
photo.
If using a permanently affixed label, Refer to the label.
the modular transmitter must
be labeled
with
its
own
FCC identification number, and, if the
FCC identification number is not
visible when the module is installed
inside another device, then the
outside of the device into which the
module is installed must also
display a label referring to the
enclosed module. This exterior label
can use wording such as the
following:“ContainsTransmitter Module
FCC ID: 2AA7C-REDLIGHTV4”Any
similarwording that expresses the
same meaning may be used. The
Grantee may either provide such a
label, an example of which must be
included
in the application for equipment
authorization, or, must provide
adequate instructions along with the
module
which
explain
this
requirement. In the latter case, a
copy of these instructions must be
included in the application for
equipment authorization.
The modular transmitter must
comply with any specific rules or
operating
requirements
that
ordinarily apply to a complete
transmitter and the manufacturer
must provide adequate instructions
along with the module to explain any
such requirements. A copy of these
instructions must be included in the
application
for
equipment
authorization.
The modular transmitter must
comply with any applicable RF
exposure requirements in its final
configuration.
Refer to manual
The EUT comply with
any applicable RF
exposure requirements
in its final configuration.
Sincerely,
Client’s signature:
Client’s name:Simon Farrell
Title :Director- Product Development & Production
Download: REDLIGHTV4 Wi-Fi & Bluetooth Module Cover Letter Modular Approval Letter1x Buzz Products PTY LTD
Mirror Download [FCC.gov]REDLIGHTV4 Wi-Fi & Bluetooth Module Cover Letter Modular Approval Letter1x Buzz Products PTY LTD
Document ID4117750
Application ID7v+57xUh1KpOf04xiUnv9A==
Document DescriptionModule Approval Letter
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeCover Letter(s)
Display FormatAdobe Acrobat PDF - pdf
Filesize16.28kB (203486 bits)
Date Submitted2018-12-26 00:00:00
Date Available2018-12-26 00:00:00
Creation Date2016-11-11 11:46:57
Producing SoftwareAcrobat Distiller 11.0 (Windows)
Document Lastmod2018-12-26 18:55:37
Document TitleModular Approval Letter1x
Document CreatorPScript5.dll Version 5.2.2
Document Author: baclks52

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : baclks52
Create Date                     : 2016:11:11 11:46:57+08:00
Modify Date                     : 2018:12:26 18:55:37-08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2018:12:26 18:55:37-08:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - Modular Approval Letter1.docx
Creator                         : baclks52
Document ID                     : uuid:82ed1a20-a803-4b66-bbdf-3f8f84e7f3f1
Instance ID                     : uuid:544ef5b6-df79-4616-b391-5fbb19dcea80
Page Count                      : 3