BLACKPRO Smart Phone RF Exposure Info EMC TRF Template COLOMBIANA DE COMERCIO S.A.

COLOMBIANA DE COMERCIO S.A. Smart Phone

Alternate Views: PDF [Zoom] Download [PDF]

                        SAR REFERENCE DIPOLE CALIBRATION REPORT                                                    Ref: ACR.273.2.18.SATU.A




       4     MEASUREMENT METHOD
The IEEE 1528, FCC KDBs and CEIIEC 62209 standards provide requirements for reference
dipoles used for system validation measurements. The following measurements were performed to
verify that the product complies with the fore mentioned standards.

       4.1    RETURN LOSS REQUIREMENTS
The dipole used for SAR system validation measurements and checks must have a return loss of —20
dB or better. The return loss measurement shall be performed against a liquid filled flat phantom,
with the phantom constructed as outlined in the fore mentioned standards.

       4.2   MECHANICAL REQUIREMENTS
The IEEE Std. 1528 and CEIIEC 62209 standards specify the mechanical components and
dimensions of the validation dipoles, with the dimensions frequency and phantom shell thickness
dependent. The COMOSAR test bench employs a 2 mm phantom shell thickness therefore the
dipoles sold for use with the COMOSAR test bench comply with the requirements set forth for a 2
mm phantom shell thickness.


5            MEASUREMENT UNCERTAINTY

All uncertainties listed below represent an expanded uncertainty expressed at approximately the 95%
confidence level using a coverage factor of k=2, traceable to the Internationally Accepted Guides to
Measurement Uncertainty.

       5.1   RETURN LOSS
The following uncertainties apply to the return loss measurement:
                    Frequency band                                     Expanded Uncertainty on Return Loss

                      400—6000MHz                                                                0.1 dB

       5.2   DIMENSION MEASUREMENT
The following uncertainties apply to the dimension measurements:
                       Length (mm)                                         Expanded Uncertainty on Length

                            3 — 300                                                             0.05 mm



       5.3   VALIDATION MEASUREMENT
The guidelines outlined in the IEEE 1528, FCC KDBs, CENELEC EN50361 and CEVIEC 62209
standards were followed to generate the measurement uncertainty for validation measurements.
                       Scan Volume                                        Expanded Uncertainty

                                1g                                                     20.3 %

                                                             Page: 5/11

              This document shall not be reproduced, except in full or in part, without the written approval ofMVG.
              The information contained herein is to be used onlyfor the purpose for which it is submitted and is not to
              be released in whole orpart withoutwritten approval ofMVG.


                               SAR REFERENCE DIPOLE CALIBRATION REPORT                                                 Ref: ACR.273.2.18.SATU.A




                                        10 g                                                          20.1 %

      6     CALIBRATION MEASUREMENT RESULTS

      6.1   RETURN LOSS AND IMPEDANCE IN HEAD LIQUID
                                                                     Frequency, MH
                                                                 1880      1900
                    S11. 48




 Frequency (MHz)                          Return Loss (dB)                              Requirement (dB)                  Impedance
       1900                                    —26.43                                         —20                       50.5 Q + 4.7 jQ

      6.2       RETURN LOSS AND IMPEDANCE IN BODY LIQUID
                                                                        Frequency, MHz
                                                                  1880           1900    1920     1940     1360
                    S11. 48




 Frequency (MHz)                   _|      Return Loss (dB)                 _|          Requirement (dB)                  Impedance
       1900                        |            —24.64                                        —20                       46.2 9 + 4.4 jQ2

      6.3       MECHANICAL DIMENSIONS

Frequency MHz                                  L mm                                             h mm                             d mm

                               required               measured                   required                measured   required            measured

     300                      420.0£1%.         |                   |       2500:H1%.             |                 6.35 £1 %.
                                                                 Page: 6/11

                This documentshall not be reproduced, except in full orin part, without the written approval ofMVG.
                The information containedhereinis to be used only forthe purpose for which it is submitted andis not to
                be releasedin whole orpart withoutwritten approval ofMVG.


                         SAR REFERENCE DIPOLE CALIBRATION REPORT                                                    Ref: ACR.273.2.18.SATU.A




      450              290.0 £1 %.                                   166.7 +1 %.                                6.35 +1 %.
      750              176.0 +1 %.                                   100.0 +1 %.                                6.35 +1 %.
      835              161.0 +1 %.                                    89.8 +1 %.                                 3.6 +1 %.
      900              149.0 +1 %.                                    83.3 +1 %.                                 3.6 +1 %.
     1450               89.1 +1 %.                                    51.7 +1 %.                                 3.6 +1 %.
     1500               80.5 +1 %.                                    50.0 +1 %.                                 3.6 +1 %.
     1640               79.0 +1 %.                                    45.7 £1 %.                                 3.6 +1 %.
     1750               75.2 +1 %.                                    42.9 £1 %.                                 3.6 +1 %.
     1800               72.0 41 %.                                    41.7 +1 %.                                 3.6 +1 %.
     1900               68.0 +1 %.                PASS                39.5 +1 %.               PASS              3.6 +1 %.          PASS
     1950               66.3 £1 %.                                    38.5 41 %.                                 3.6 +1 %.
     2000               64.5 £1%.                                     37.5 +1 %.                                 3.6 +1 %.
     2100               61.0£1%.                                      35.7 £1 %.                                 3.6 +1 %.
     2300               55.5 +1 %.                                    32.6 1 %.                                  3.6 +1 %.
     2450               51.5 41 %.                                    30.4 £1 %.                                 3.6 +1 %.
     2600               48.5 £1 %.                                    28.8 1 %.                                  3.6 +1 %.
     3000               41.5 £1%.                                     25.0 +1 %.                                 3.6 +1 %.
     3500               37.0£1%.                                      264 £1 %.                                  3.6 +1 %.
     3700               34.741%.                                      264 £1 %.                                  3.6 +1 %.

       7     VALIDATION MEASUREMENT
The IEEE Std. 1528, FCC KDBs and CEVIEC 62209 standards state that the system validation
measurements must be performed using a reference dipole meeting the fore mentioned return loss
and mechanical dimension requirements. The validation measurement must be performed against a
liquid filled flat phantom, with the phantom constructed as outlined in the fore mentioned standards.
Per the standards, the dipole shall be positioned below the bottom of the phantom, with the dipole
length centered and parallel to the longest dimension of the flat phantom, with the top surface of the
dipole at the described distance from the bottom surface of the phantom.

       7.1   HEAD LIQUID MEASUREMENT

                        Fre’cll:fzncy           Relative permittivity (€,")             Conductivity {0) S/m

                                               required           measured            required          measured

                            300                45.3 15 %                              0.87 25 %
                            450                43.5 15 %                              0.87 25 %
                            750                41.9 15 %                              0.89 25 %

                            835                41.5 +5 %                              0.90 £5 %
                            900                41.5 45 %                              0.97 25 %

                            1450               40.5 45 %                              1.20 £5 %
                            1500               40.4 45 %                              1,23 £5 %
                            1640               40.2 45 %                              1.31 45 %
                            1750               40.1 45 %                              1.37 45 %

                                                              Page: 7/11

               This document shall not be reproduced, except in full or in part, without the written approval ofMVG.
               The information contained herein is to be used onlyfor the purpose for which it is submitted and is not to
               be released in whole orpart withoutwritten approval ofMVG.


                           SAR REFERENCE DIPOLE CALIBRATION REPORT                                                    Ref: ACR.273.2.18.SATU.A




                              1800               40.0 45 %                              1.40 £5 %
                              1900               40.0 15 %             PASS             1.40 £5 %            PASS

                              1950               40.0 15 %                              1.40 £5 %
                              2000               40.0 15 %                              1.40 £5 %
                              2100               39.8 15 %                              1.49 £5 %

                              2300               39.5 45 %                              1.67 £5.%
                              2450               39.2 +5 %                              1.80 £5 %

                              2600               39.0 +5 %                              1.96 £5 %
                              3000               38.5 +5 %                              2.40 £5 %

                              3500               37.9 45 %                              2.91 +5 %


           7.2   SAR MEASUREMENT RESULT WITH HEAD LIQUID
The IEEE Std. 1528 and CEIIEC 62209 standards state that the system validation measurements
should produce the SAR values shown below (for phantom thickness of 2 mm), within the
uncertainty for the system validation. All SAR values are normalized to 1 W forward power. In
bracket, the measured SAR is given with the used input power.

Software                                                                OPENSAR V4
Phantom                                                                  SN 20/09 SAM7I
Probe                                                                    SN 18/11 EPG122
Liquid                                                                  Head Liquid Values: eps‘ : 38.5 sigma : 1.45
Distance between dipole center and liquid                               10.0 mm
Area scan resolution                                                    dx=8mm/dy=8mm
Zoon Scan Resolution                                                    dx=8mm/dy=8mm/dz=Smm
Frequency                                                               1900 MHz
Input power                                                             20 dBm
Liquid Temperature                                                      MCC
Lab Temperature                                                         M C
Lab Humidity                                                            45 %




                          F'e'cl‘;ez"q’              1 g SAR (W/ke/w)                      10 g SAR (W/ke/w)
                                                 required           measured            required          measured

                              300                   2.85                                   1.94
                              450                   4.58                                   3.06
                              750                   8.49                                   $95

                              835                   9.56                                   6.22
                              900                   10.9                                   6.99

                              1450                   29                                     16
                              1500                  30.5                                   16.8
                              1640                  34.2                                   184
                              1750                  36.4                                   19.3
                              1800                  38.4                                   20.1

                                                                Page: 8/11

                 This document shall not be reproduced, except in full or in part, without the written approval ofMVG.
                 The information contained herein is to be used onlyfor the purpose for which it is submitted and is not to
                 be released in whole orpart withoutwritten approval ofMVG.


[amue                        SAR REFERENCE DIPOLE CALIBRATION REPORT                                                  Ref: ACR.273.2.18.SATU.A



                                 1900                39.7           40.03 (4.00)           20.5           20.55 (2.06)
                                 1950                40.5                                  20.9
                                 2000                411                                   211
                                 2100                43.6                                  219
                                 2300                48.7                                  73.3
                                 2450                52.4                                   24
                                 2600                55.3                                  24.6
                                 3000                63.8                                  25.7
                                 3500                67.1                                   25
                                 3700                67.4                                  24.2


   wl             |biee nitues                     sanm




   znxftnn                                                                                 g
 teax        ow                                                                            §


 me) bra)         *                                  i e                                       $st                                  1     i
                      en                                                                          $ 2 4         10 12 gmf\ ts m & m t ce oo




        7.3       BODY LIQUID MEASUREMENT

                            Fre:fll:-‘ezncv         Relative permittivity (€/‘)             Conductivity (0) S/m

                                                   required          measured            required         measured

                                 150              61.9 15 %                             0.80 £5 %
                                 300              58.2 45 %                             0.92 £5 %
                                 450              56.7 £5 %                             0.94 £5 %
                                 750              55.5 45 %                             0.96 £5 %
                                 835              55.2 £5 %                             0.97 £5 %

                                 900              55.0 £5 %                             1.05 45 %
                                 915              55.0 £5 %                             1.06 45 %

                                 1450             54.0 £5 %                             1.30 25 %
                                 1610             53.8 £5 %                             1.40 £5 %

                                 1800             53.3 45 %                             1.52 45 %
                                 1900             53.3 15 %             PASS            1.52 15 %            PASS
                                 2000             53.3 15 %                             1.52 5 %

                                 2100             53.2 45 %                             1.62 5 %

                                                                 Page: 9/11

                   This document shall not be reproduced, except in full orin part, without the written approval ofMVG.
                   The information contained herein isto be used onlyfor the purpose for which it issubmitted and is not to
                   be released in whole orpart without written approval ofMVG.




                                                              en nsc y < >


(Lbus                     SAR REFERENCE DIPOLE CALIBRATION REPORT                                                 Ref: ACR.273.2.18.SATU.A




                               2300            52.9 15 %                             1.81 45 %

                               2450            52.7 £5 %                             1.95 45 %

                               2600            52.5 45 %                             2.16 45 %
                               3000            52.0 £5 %                             2.73 45 %

                               3500            51.3 15 %                             3.31 15 %

                               3700            51.0 £5 %                             3.55 45 %

                               5200            49.0 £10 %                           5.30 £10 %

                               5300            48.9 £10 %                           5.42 £10%
                               5400            48.7 £10 %                           5.53 410 %

                               5500            48.6 £10 %                           5.65 £10 %
                               5600            48.5 £10 %                           5.77 £10 %

                               5800            48.2 £10 %                           6.00 £10 %


           74    SAR MEASUREMENT RESULT WITH BODY LIQUID
Software                                                                 OPENSAR V4
Phantom                                                                  SN 20/09 SAM71
Probe                                                                    SN 18/11 EPG122
Liquid                                                                   Body Liquid Values: eps‘ : 53.3 sigma : 1.56
Distance between dipole center and liquid                                10.0 mm
Area scan resolution                                                     dx=8mm/dy=8mm
Zoon Scan Resolution                                                     dx=8mm/dy=8mm/dz=Smm
Frequency                                                                1900 MHz
Input power                                                              20 dBm
Liquid Temperature                                                       21 °C
Lab Temperature                                                          21 °C
Lab Humidity                                                             45 %




                          F'e:,":fznc"              1 g SAR (W/kg/w)                    10 g SAR (W/kg/w)
                                                          measured                           measured

                               1900                       40.91 (4.09)                      21.40 (2.14)


                   ammommee




                 d                                                                        y
    couta)
             )


   we ] "cna)                                         w

                       Xim 3     vie
                                                                                                   i 606 t im rs ts & 2s t t m cb
                                                                                                                  Z i)


                                                               Page: 10/11

                 This document shall not be reproduced, except in full or in part, without the written approval ofMVG.
                 The information contained hereinis to be used onlyforthe purposefor which it is submitted andis not to
                 be releasedin whole orpart withoutwrittenapproval ofMVG.


                                                                                                                      Ref: ACR.273.2.18.SATU.A
 mvG                        SAR REFERENCE DIPOLE CALIBRATION REPORT




       8    LIST OF EQUIPMENT



                                                Equipment Summary Sheet

   Equipment                 Manufacturer / Identification No        Current                                            Next Calibration
   Description                   Model                        ‘| Calibration Date                                             Date
                                                                                        alidated. No cal              Validated.      No    cal
   SAM Phantom                        MVG                  SN—20/09—SAM71             required.                       required.

                                          ;                                             alidated. No cal                alidated.     No    cal
COMOSAR Test Bench                 Version 3                         NA               required.                       required.

  Network Analyzer           Rhode &Schwarz                     sN100132                        022016                        0222019
      Calipers                       Carrera                  CALIPER—01                        01/2017                       01/2020

  Reference Probe                     MVG                  EPG122 SN 18/11                      10/2017                       10/2018

     Multimeter                 Keithley 2000                     1188656                       01/2017                       01/2020

  Signal Generator             Agilent E4438C                 MY49070581                        01/2017                       01/2020

      Amplifier                  Asthersomim                      SN 046               tCharac‘[erized pri_or to |Characterized pri_or to
                                                                                        est. No cal required. |test. No cal required.

    Power Meter                   HP E4418A                   US38261498                        01/2017                       01/2020

   Power Sensor                 HP ECP—E26A                    US37181460                       01/2017                       01/2020

 Directional Coupler           Narda 4216—20                       01386               Characterized pri_or to |Characterized pri_or to
                                                                                       test. No cal required. |test. No cal required.
  Temperature and
  Humidity Sensor             Control Company                   150798832                       1172017                       11/2020




                                                               Page: 11/11

                  This document shall not be reproduced, except in full or in part, without the written approval ofMVG.
                  The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to
                  be released in whole orpart without written approval ofMVG.




                                                             en nsc y < >


SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.                             FCC ID: 2AEPIBLACKPRO           Report No.: LCS181220056AEB

   5.6 S1D2450 Dipole Calibration Ceriticate




                                                                    (/(.\
                                                              SATIMO
                                                              The microwave vision company_A




                                   SAR Reference Dipole Calibration Report



                                                                    Ref : ACR.287.8.14.SATU.A




                            SHENZHEN LCS COMPLIANCE TESTING
                                   LABORATORY LTD.
                           1F., XINGYUAN INDUSTRIAL PARK, TONGDA ROAD,
                                            BAO‘AN BLVD
                         BAO‘AN DISTRICT, SHENZHEN, GUANGDONG, CHINA
                            SATIMO COMOSAR REFERENCE DIPOLE
                                                  FREQUENCY: 2450 MHZ
                                                  SERIAL NO.: SN 07/14 DIP 2G450—306

                                                      Calibrated at SATIMO US
                                              2105 Barrett Park Dr. — Kennesaw, GA 30144




                                                                   10/01/2018

                                Summ ary.


                                This document presents the methodand results from an accredited SAR reference dipole calibration
                                performed in SATIMO USA using the COMOSAR test bench. All calibration results are traceable
                                to national metrologyinstitutions.




   This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
                                                               Page 119 of 151


SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.                                     FCC ID: 2AEPIBLACKPRO                       Report No.: LCS181220056AEB




            (¢ :                     SAR REFERENCE DIPOLE CALIBRATION REPORT                                                   ReF AckaangddSATHA
          SATINJD




                                              Name                              Function                          Date                   Signature
           Prepared by :                 Jérome LUC                        Product Manager                   10/14/2018                   jg

           Checked by:                   Jérome LUC                        Product Manager                   10/14/2018                    fi’

           Approved by :           Kim RUTKOWSKI                           Quality Manager                   10/14/2018                _/ ,,, puthewt)?




                                                                               |__Customer Name
                                                                                  Shenzhen LCS
                                                  Distribution :                Compliance Testing
                                                                                  Laboratory Ltd.




               Issue                   Date                                                        Modifications
                 A                 10/14/2018                 Initial release




                                                                         Page: 2/11

                            This document shall not be reproduced, except in full orinpart, without the written approval ofSATIMO.
                            The information contained herein is to be used onlyforthe purposefor which it is submitted and is not to
                            be released in whole orpart without written approval ofSATIMO.




   This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
                                                               Page 120 of 151


     (( 4   \                SAR REFERENCE DIPOLE CALIBRATION REPORT                                                   Ref: ACR287.8.14.SATU.A
sArImo

                                                     TABLE OF CONTENTS




 ]      IMfodu@HONM:—mmeorommrenmenremmmareresmenmcqreremmreryeemcrmmmemrormmersmenmem 4

B       De¥IG@ URCCF TeSE . .. .. c corermvecmmmnmmnnmmmemmemmmnimemmmnmmmnmmmntrmmecmrorncmmmetiernsosnzcon 4
3\      PFOUUGCE DeSCFIPLION ... mmmmemmmmmmmenmnmmmemmmmmremmnemenerenemennimmeremnntrermyersmieermes 4
      3.1     General Information                                                                                                           4

:       MeASURCMeNENTCHAIOE —:——+—mmrmmemmmmmreneeeeceerormmemermsemsmsmeneereremeermenmemsecemesceme 5
      4.1     Return Loss Requirements                                                                                                      5

      4.2     Mechanical Requirements                                                                                                       $
5       MCASUT@ME@Nt UNC@TEANEY ... ... en eeemmeemeememeeeneee n n en en en ernernenneernernerne en erenenes $

      5.1     Return Loss                                                                                                                   $

      5.2     Dimension Measurement                                                                                                         5
      5.3     Validation Measurement                                                                                                        $

6       CalibFAtiON MEASUT@MENE RESUIS .............2.cene e en en reeneeneemneeneen e 6
      6.1     Return Loss and Impedance                                                                                                     6

      6.2     Mechanical Dimensions                                                                                                         6
7       Validation measurement ...

      71      Head Liquid Measurement                                                                                                       7

      7.2     SAR Measurement Result With Head Liquid                                                                                       7

      7.3     Body Liquid Measurement                                                                                                       9
      7.4     SAR Measurement Result With Body Liquid                                                                                       9
        LASE Of EQUHDMIGME :0000 mmmeeremrermerommimrrerervomreremarmrememmeraecrememmnrnmyrerare; 11
50




                                                                 Page: 3/11

                    This document shall not be reproduced, except in full or in part, without the written approval ofSATIMO.
                    The information contained herein is to be used onlyforthe purposefor which it is submitted and is not to
                    be released in whole orpart without written approval ofSATIMO.




                                                              e ces y c >


    (((. \              SAR REFERENCE DIPOLE CALIBRATION REPORT                                                   Ki RCmesisAdgATLRIL



1            INTRODUCTION


This document contains a summary of the requirements set forth by the IEEE 1528, OET 65 Bulletin

C and CEVIEC 62209 standards for reference dipoles used for SAR measurement system validations
and the measurements that were performed to verify that the product complies with the fore
mentioned standards.




2            DEVICE UNDER TEST




                                                   Device Under Test
        Device Type                                       COMOSAR 2450 MHz REFERENCE DIPOLE
        Manufacturer                                      Satimo
        Model                                             $1D2450
        Serial Number                                     SN 07/14 DIP 2G450—306
        Product Condition (new / used)                    New

A yearly calibration interval is recommended.

3            PRODUCT DESCRIPTION

3.1     GENERAL INFORMATION

Satimo‘s COMOSAR Validation Dipoles are built in accordance to the IEEE 1528, OET 65 Bulletin
C and CEIIEC 62209 standards. The product is designed for use with the COMOSAR test bench
only.




                              Figure 1 — Satimo COMOSAR Validation Dipole




                                                            Page: 4/11

              This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO.
              The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to
              be released in whole orpart without written approval ofSATIMO.


 ([(                      SAR REFERENCE DIPOLE CALIBRATION REPORT                                                  Ref: ACR.287 8.14.SATU.A
SATIMD

       4     MEASUREMENT METHOD
The IEEE 1528, OET 65 Bulletin C and CELIIEC 62209 standards provide requirements for
reference dipoles used for system validation measurements. The following measurements were
performed to verify that the product complies with the fore mentioned standards.

       4.1   RETURN LOSS REQUIREMENTS
The dipole used for SAR system validation measurements and checks must have a return loss of —20
dB or better. The return loss measurement shall be performed against a liquid filled flat phantom,
with the phantom constucted as outlined in the fore mentioned standards.

       4.2   MECHANICAL REQUIREMENTS
The IEEE Std. 1528 and CEIMIEC 62209 standards specify the mechanical components and
dimensions of the validation dipoles, with the dimensions frequency and phantom shell thickness
dependent. The COMOSAR test bench employs a 2 mm phantom shell thickness therefore the
dipoles sold for use with the COMOSAR test bench comply with the requirements set forth for a 2
mm phantom shell thickness.


5            MEASUREMENT UNCERTAINTY

All uncertainties listed below represent an expanded uncertainty expressed at approximately the 95%
confidence level using a coverage factor of k=2, traceable to the Internationally Accepted Guides to
Measurement Uncertainty.

       5.1   RETURNLOSS
The following uncertainties apply to the return loss measurement:
                      Frequency band                                    Expanded Uncertainty on Return Loss
                        400—6000MHz                                                               0.1 dB

       5.2   DIMENSION MEASUREMENT
The following uncertainties apply to the dimension measurements:
                         Length (mm)                                        Expanded Uncertainty on Length

                              3 — 300                                                            0.05 mm



       5.3   VALIDATION MEASUREMENT
The guidelines outlined in the IEEE 1528, OET 65 Bulletin C, CENELEC EN50361 and CEIIEC
62209 standards were followed to generate the measurement uncertainty for validation
measurements.
                         Scan Volume                                       Expanded Uncertainty
                                  1 g                                                   20.3 %
                                 10 g                                                   20.1 %

                                                              Page: 5/11
                This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO.
                The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to
                be released in whole orpart without written approval ofSATIMO.


 (((                                SAR REFERENCE DIPOLE CALIBRATION REPORT                                              Ref: ACR287.8.14.SATU.A
sArImo     7




         6      CALIBRATION MEASUREMENT RESULTS

         6.1        RETURN LOSS                   AND IMPEDANCE
                                                                         Frequency, MHz
                                     2350         2380   2400     2420     2440     2460     2480       2500   2520   2550
                         S11, 48




                                   30—

   Frequency (MHz)                               Return Loss (dB)                     Requirement (dB)                         Impedance
        2450                                          —25.59                                —20                              44.7 Q — 1.1 j62

         6.2        MECHANICAL DIMENSIONS
 Frequency MHz                                   L mm                                        h mm                                  d mm

                                    required             measured                 required              measured      required            measured

       300                         420.0 £1 %.                                250.0 £1 %.                             6.35 +1 %.

       450                         290.0 £1 %.                                166.7 £1 %.           |                 6.35 £1 %.
       750                         176.0 £1 %.                                100.0 £1 %.                             6.35 £1 %.

       835                         161.0 +1 %.                                 89.8 +1 %.                             3.6 £1 %.
       900                         149.0 £1 %.                                83.3 +1%.                               3.6 +1 %.

       1450                        89.1 +1 %.                                  51.7 £1 %.                             3.6 +1 %.
       1500                        80.5 £1 %.                                  50.0 £1 %.       |                     3.6 £1 %.

       1640                        79.0 1 %.                                   45.7 £1%.                              3.6 £1 %.
       1750                        75.2 £1%.                                   42.9 £1%.            |                 3.6 £1 %.

       1800                        72.0 £1 %.                                  41.7 £1%.                              3.6 £1 %.

       1900                        68.0 +1 %.                                  39.5 £1%.                              3.6 £1 %.
       1950                        66.3 +1 %.                                  38.5 £1%.                              3.6 £1 %.

       2000                        64.5 41 %.                                  37.5 £1%.                              3.6 £1 %.
       2100                        61.0 +1 %.                                  35.7 £1%.                              3.6 +1 %.

       2300                        55.5 41 %.                                  32.6 +1 %.                             3.6 £1 %.

       2450                        51.5 41 %.              PASS                30.4 £1%.                   PASS       3.6 41 %.             PASS
       2600                        48.5 +1 %.                                  28.8 £1%.                              3.6 +1 %.

       3000                        41.5 £1%.                                   25.0 £1%.                              3.6 £1 %.

       3500                        37.0%1%.                                    26.4 £1%.                              3.6 £1 %.

       3700                        34.7%1%.                                    26.4 £1%.                              3.6 +1 %.


                                                                         Page: 6/11

                    This document shall not be reproduced, except in full orin part, without the written approval ofSATIMO.
                    The information contained hereinis to be used onlyforthepurposefor whichit is submitted and is not to
                    be released in whole orpart withoutwrittenapproval ofSATIMO.




 noonneree reue e e e n mnnne tm nenenap snn gnegy en ces                                                                     non n n emereg eeme se se y mc


 ((( \                      SAR REFERENCE DIPOLE CALIBRATION REPORT                                                  Ref: ACR.287 8.14.SATU.A
SATIMO

           7     VALIDATION MEASUREMENT
The IEEE Std. 1528, OET 65 Bulletin C and CEIIEC 62209 standards state that the system
validation measurements must be performed using a reference dipole meeting the fore mentioned
return loss and mechanical dimension requirements. The validation measurement must be performed
against a liquid filled flat phantom, with the phantom constructed as outlined in the fore mentioned
standards. Per the standards, the dipole shall be positioned below the bottom of the phantom, with
the dipole length centered and parallel to the longest dimension of the flat phantom, with the top
surface of the dipole at the described distance from the bottom surface of the phantom.

           7.1   HEAD LIQUID MEASUREMENT

                           Fre’?/lu:zncy          Relative permittivity (€,‘)             Conductivity {0) S/m

                                                  required          measured            required          measured

                               300               45.3 15 %                             0.87 £5 %
                               450               43.5 25 %                              0.87 £5 %

                               750               41.9 25 %                              0.89 £5 %
                               835               41.5 25 %                              0.90 +5 %
                               900               41.5 25 %                              0.97 £5 %
                              1450               40.5 45 %                              1.20 25 %

                              1500               40.4 15 %                              123125 %
                              1640               40.2 25 %                              1.31 15 %
                              1750               40.1 25 %                              1.37 25 %
                              1800               40.0 25 %                              1.40 25 %
                              1900               40.0 25 %                              140 25 %
                              1950               40.0 25 %                              140 £5 %

                              2000               40.0 25 %                              140 25 %
                              2100               39.8 45 %                              149 £5 %
                              2300               39.5 45 %                              1.67 25 %
                              2450               39.2 25 %             PASS             1.80 25 %            PASS
                              2600               39.0 25 %                              1.96 25 %

                              3000               38.5 15 %                              2.40 £5 %
                              3500               37.9 25 %                              2.91 +5 %


           7.2    SAR MEASUREMENT RESULT WITH HEAD LIQUID
The IEEE Std. 1528 and CEUIEC 62209 standards state that the system validation measurements
should produce the SAR values shown below (for phantom thickness of 2 mm), within the
uncertainty for the system validation. All SAR values are normalized to 1 W forward power. In
bracket, the measured SAR is given with the used input power.

Software                                                                 OPENSAR V4
Phantom                                                                  SN 20/09 SAM71
Probe                                                                    SN 18/11 BPG122
Liquid                                                                   Head Liquid Values: eps‘ : 39.0 sigma : 1.77
Distance between dipole center and liquid                                10.0 mm
Area scan resolution                                                     dx=8mm/dy=8mm

                                                                Page: 7/11

                  This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO.
                  The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to
                  be released in whole orpart without written approval ofSATIMO.


 (( L. \                      SAR REFERENCE DIPOLE CALIBRATION REPORT                                                         Ref: ACR.287.8.14.SATU.A
SATIMD

Zoon Scan Resolution                                                     dx=8mm/dy=8m/dz=5mm
Frequency                                                                2450 MHz
Input power                                                              20 dBm
Liquid Temperature                                                       71 °C
Lab Temperature                                                          21 °C
Lab Humidity                                                             45 %




                              F
                                  "Ume*                1 g SAR (W/ke/w)                    10 g SAR (W/kg/w)
                                                  required           measured            required                measured

                                     300             2.85                                  1.94

                                     450             4.58                                  3.06

                                     750             8.49                                  5.55

                                     835             9.56                                  6.22

                                     900             10.9                                  6.99
                                     1450             29                                    16

                                     1500            30.5                                  16.8

                                     1640            34.2                                  18.4

                                     1750            36.4                                  19.3

                                     1800            38.4                                  20.1

                                     1900            $9.7                                  20.5
                                     1950            40.5                                  20.9

                                  2000               41.1                                  21.1

                                  2100               43.6                                  21.9

                                  2300               48.7                                  23.3

                                  2450               52.4           53.89 (5.39)            24                  24.15 (2.42)
                                  2600               55.3                                  24.6

                                     3000            63.8                                  25.7

                                     3500            67.1                                   25


                      remrmmrommm                                                                  z



                                                                                                                         C
                   Suties ic nerws                 mmemo«_|                                  "A"
     Sinkd
      ns
          PC
          t                                                                                                              Bunl



          Jt
          Soih                                                                               8767
                                                                                             ©00—       \


   ( — x:                                                                                  % 800—           \
   n an      w‘-                                                                           % «00                 \\


                                                                                             200—                     \\
   we} c                                                                                     ass—                               TU*———
                    [ ximet B Yieet                                                                 0   2   4   6   8   10 12 'IZ‘[MWH: 18 20 22 2 % m 30




                                                                Page: 8/11

                   This document shall not be reproduced, except in full or in part, without the written approval ofSATIMO.
                   The information contained herein is to be used onlyforthe purposefor which it is submitted and is not to
                   be released in whole orpart without written approval ofSATIMO.




                                                              e ce y c >


 (((. \                    SAR REFERENCE DIPOLE CALIBRATION REPORT                                                  Ki RCmesisAdgATLRIL
SATIIV,ID

        7.3    BODY LIQUID MEASUREMENT
                          F
                              re:,l":z"“’        Relative permittivity (€,‘)             Conductivity (0) S/m
                                                 required          measured            required          measured

                                150             61.9 £5 %                             0.80 £5 %
                               300              58.2 45 %                             0.92 £5%
                               450              56.7 £5 %                             0.94 £5%
                                750             55.5 45 %                             0.96 £5%
                                835             55.2 45 %                             0.97 £5 %
                               900              55.0 45 %                              1.05 £5 %
                               915              55.0 45 %                              1.06 £5 %
                               1450             54.0 £5 %                              1.30 +5 %
                               1610             53.8 45 %                              140 +5 %
                               1800             53.3 45 %                              1.52 45 %
                               1900             53.3 45 %                              1.52 45 %
                               2000             53.3 15 %                              1.52 +5 %
                               2100             53.2 +5 %                              1.62 +5 %
                               2450             52.7 45 %             PASS             1.95 +5 %            PASS
                               2600             52.5 45 %                             21645 %
                               3000             52.0 45 %                             2.73 45 %
                               3500             51.3 +5 %                             3.31 +5 %
                               5200            49.0 £10%                              5.30 £10%
                               5300            48.9 £10%                              5.42£10%
                               5400            48.7 £10%                              5.53 210 %
                               5500            48.6 £10%                              5.65 £10 %
                               5600            48.5 £10%                              5.77 £10%
                               5800            48.2 £10 %                             6.00 £10%




        74     SAR MEASUREMENT RESULT WITH BODY LIQUID
Software                                                                OPENSAR V4
Phantom                                                                 SN 20/09 SAM71
Probe                                                                   SN 18/11 EPG122
Liquid                                                                  Body Liquid Values: eps‘ : 53.0 sigma : 1.93
Distance between dipole center and liquid                               10.0 mm
Area scan resolution                                                    dx=8mm/dy=8mm
Zoon Scan Resolution                                                    dx=8mm/dy=8m/dz=5mm
Frequency                                                               2450 MHz
Input power                                                             20 dBm
Liquid Temperature                                                      21 °C
Lab Temperature                                                         21 °C
Lab Humidity                                                            45 %




                                                               Page: /11

                 This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO.
                 The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to
                 be released in whole orpart without written approval ofSATIMO.




                                                            e ces        y c>



Document Created: 2019-02-13 09:55:27
Document Modified: 2019-02-13 09:55:27
Download: BLACKPRO Smart Phone RF Exposure Info EMC TRF Template COLOMBIANA DE COMERCIO S.A.
Mirror Download [FCC.gov]BLACKPRO Smart Phone RF Exposure Info EMC TRF Template COLOMBIANA DE COMERCIO S.A.
Document ID4170897
Application IDLwTDTAyJpphVsTDJ1J5YJA==
Document DescriptionLCS181220056AEB_FCC SAR Part-4
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeRF Exposure Info
Display FormatAdobe Acrobat PDF - pdf
Filesize452.47kB (5655862 bits)
Date Submitted2019-02-18 00:00:00
Date Available2019-02-18 00:00:00
Creation Date2019-02-13 09:49:42
Producing SoftwareMicrosoft? Office Word 2007
Document Lastmod2019-02-13 09:55:27
Document TitleEMC TRF Template
Document CreatorMicrosoft? Office Word 2007
Document Author: eie