MF8300 CREATIVE METALLIX PLUS RF Exposure Info SZEM170900985504 MPE x Creative Labs Pte. Ltd.

Creative Labs Pte. Ltd. CREATIVE METALLIX PLUS

Page 1 of MF8300 CREATIVE METALLIX PLUS RF Exposure Info SZEM170900985504 MPE x Creative Labs Pte. Ltd.
Page 2 of MF8300 CREATIVE METALLIX PLUS RF Exposure Info SZEM170900985504 MPE x Creative Labs Pte. Ltd.
Page 3 of MF8300 CREATIVE METALLIX PLUS RF Exposure Info SZEM170900985504 MPE x Creative Labs Pte. Ltd.
Page 4 of MF8300 CREATIVE METALLIX PLUS RF Exposure Info SZEM170900985504 MPE x Creative Labs Pte. Ltd.
Page 5 of MF8300 CREATIVE METALLIX PLUS RF Exposure Info SZEM170900985504 MPE x Creative Labs Pte. Ltd.
Page 6 of MF8300 CREATIVE METALLIX PLUS RF Exposure Info SZEM170900985504 MPE x Creative Labs Pte. Ltd.
Page 7 of MF8300 CREATIVE METALLIX PLUS RF Exposure Info SZEM170900985504 MPE x Creative Labs Pte. Ltd.

SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
No. 1 Workshop, M-10, Middle section, Science & Technology Park,
Shenzhen, Guangdong, China 518057
Telephone:
+86 (0) 755 2601 2053
Fax:
+86 (0) 755 2671 0594
Email:
ee.shenzhen@sgs.com
Report No.: SZEM170900985504
Page:
1 of 7
Cover page
SAR Evaluation Report
Application No.:
Applicant:
Address of Applicant:
Manufacturer:
Address of Manufacturer:
SZEM1709009855CR
Creative Labs Pte. Ltd.
31 International Business Park, #03-01 Creative Resource, Singapore 609921
Creative Labs Pte. Ltd.
31 International Business Park, #03-01 Creative Resource, Singapore 609921
Equipment Under Test (EUT):
EUT Name:
CREATIVE METALLIX PLUS
Model No.:
MF8300
FCC ID:
2AJIV-MF8300
Trade mark:
CREATIVE
47 CFR Part 1.1307
Standard(s) :
47 CFR Part 2.1093
KDB447498D01 General RF Exposure Guidance v06
2017-09-18
Date of Receipt:
Date of Test:
2017-09-20 to 2017-09-24
Date of Issue:
2017-09-30
Test Result:
Pass*
In the configuration tested, the EUT complied with the standards specified above.
Authorized Signature:
Jack Zhang
EMC Laboratory Manager
The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report.
If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new
system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International
Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International
Electrical Approvals in writing.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985504
Page:
2 of 7
Version
Revision Record
Version
Chapter
01
Date
2017-09-30
Modifier
Remark
Original
Authorized for issue by:
Vincent Chen /Project Engineer
Eric Fu /Reviewer
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only
and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985504
Page:
3 of 7
Contents
Page
COVER PAGE .....................................................................................................................................................1
VERSION..............................................................................................................................................................2
CONTENTS ..........................................................................................................................................................3
GENERAL INFORMATION ................................................................................................................................4
4.1
4.2
4.3
4.4
4.5
4.6
GENERAL DESCRIPTION OF EUT ..........................................................................................................................4
TEST LOCATION ..................................................................................................................................................5
TEST FACILITY ...................................................................................................................................................5
DEVIATION FROM STANDARDS ............................................................................................................................5
ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................................5
OTHER INFORMATION REQUESTED BY THE CUSTOMER .........................................................................................5
SAR EVALUATION .............................................................................................................................................6
5.1 RF E XPOSURE COMPLIANCE REQUIREMENT .........................................................................................................6
5.1.1 Standard Requirement ...........................................................................................................................6
5.1.2 Limits .......................................................................................................................................................6
5.1.3 EUT RF Exposure .............................................................................................................................. 6-7
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only
and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985504
Page:
4 of 7
General Information
4.1 General Description of EUT
BLE:
Power supply:
Power by Li-ion battery DC 3.7V, 4400mAh
USB input: DC 5V, 1A
Cable:
USB cable 65cm unshielded
Internal source
26MHz
Frequency Range:
2402MHz to 2480MHz
Bluetooth Version:
BT 4.2 dual mode
Modulation Type:
GFSK
Number of Channels:
40
Antenna Type:
Monopole
Antenna Gain:
2dBi
BT Classic:
Power supply:
Power by Li-ion battery DC 3.7V, 4400mAh
USB input: DC 5V, 1A
Cable:
USB cable 65cm unshielded
Internal source
26MHz
Frequency Range:
2402MHz to 2480MHz
Bluetooth Version:
BT 4.2 dual mode
Modulation Technique:
Frequency Hopping Spread Spectrum(FHSS)
Modulation Type:
GFSK, π/4DQPSK, 8DPSK
Number of Channels:
79
Hopping Channel Type:
Adaptive Frequency Hopping systems
Antenna Type:
Monopole
Antenna Gain:
2dBi
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only
and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985504
Page:
5 of 7
4.2 Test Location
All tests were performed at:
SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch
No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China
518057
Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594
No tests were sub-contracted.
4.3 Test Facility
The test facility is recognized, certified, or accredited by the following organizations:
• CNAS (No. CNAS L2929)
CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC
Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration
Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration
Laboratories) for the competence in the field of testing.
• A2LA (Certificate No. 3816.01)
SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the
American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01.
• VCCI
The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services
Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with
Registration No.: G-823, R-4188, T-1153 and C-2383 respectively.
• FCC –Designation Number: CN1178
SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized
as an accredited testing laboratory.
Designation Number: CN1178. Test Firm Registration Number: 406779.
• Industry Canada (IC)
Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards
Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and
Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1,
4620C-2, 4620C-3.
4.4 Deviation from Standards
None.
4.5 Abnormalities from Standard Conditions
None.
4.6 Other Information Requested by the Customer
None.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only
and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985504
Page:
6 of 7
SAR Evaluation
5.1 RF Exposure Compliance Requirement
5.1.1 Standard Requirement
According to KDB447498D01 General RF Exposure Guidance v06
4.3.1. Standalone SAR test exclusion considerations
Unless specifically required by the published RF exposure KDB procedures, standalone 1-g
head or body and 10-g extremity SAR evaluation for general population exposure conditions, by
measurement or numerical simulation, is not required when the corresponding SAR Exclusion
Threshold condition, listed below, is satisfied.
5.1.2 Limits
The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances
≤ 50 mm are determined by:
[(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·
[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where
 f(GHz) is the RF channel transmit frequency in GHz
 Power and distance are rounded to the nearest mW and mm before calculation17
 The result is rounded to one decimal place for comparison
The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and
for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation
distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion
5.1.3 EUT RF Exposure
BT:
The Max Conducted Peak Output Power1.92
is
dBm on the lowest channel2.48
1.92 dBm logarithmic terms convert to numeric result is nearly 1.56 mW
According to the formula. calculate the test exclusion thresholds:
[(max. power of channel, including tune-up tolerance, mW)/
(min. test separation distance, mm)] · [√f(GHz)]
General RF Exposure = (1.56 mW / 5 mm) x √2.48 GHz = 0.49
(1)
SAR requirement:
S = 3.0
(2)
(1) < (2)
So the SAR report is not required.
GHz
Note: Refer to report No. SZEM170900985502 for EUT test value.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only
and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985504
Page:
7 of 7
BLE:
The Max Conducted Peak Output Power1.79
is
dBm on the lowest channel2.48
1.79 dBm logarithmic terms convert to numeric result is nearly 1.51 mW
According to the formula. calculate the test exclusion thresholds:
[(max. power of channel, including tune-up tolerance, mW)/
(min. test separation distance, mm)] · [√f(GHz)]
General RF Exposure = (1.51 mW / 5 mm) x √2.48 GHz = 0.48
(1)
SAR requirement:
S = 3.0
(2)
(1) < (2)
So the SAR report is not required.
GHz
Note: Refer to report No. SZEM170900985503 for EUT test EIRP value.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only
and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Download: MF8300 CREATIVE METALLIX PLUS RF Exposure Info SZEM170900985504 MPE x Creative Labs Pte. Ltd.
Mirror Download [FCC.gov]MF8300 CREATIVE METALLIX PLUS RF Exposure Info SZEM170900985504 MPE x Creative Labs Pte. Ltd.
Document ID3634630
Application IDYObFynNjLNft06nZzXKn1g==
Document DescriptionRF Exposure Info
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeRF Exposure Info
Display FormatAdobe Acrobat PDF - pdf
Filesize17.15kB (214324 bits)
Date Submitted2017-11-10 00:00:00
Date Available2017-11-10 00:00:00
Creation Date2017-11-03 11:03:49
Producing SoftwareGPL Ghostscript 8.64
Document Lastmod2017-11-03 03:03:49
Document TitleSZEM170900985504 MPE x
Document CreatorPScript5.dll Version 5.2.2
Document Author: kate_bian

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Page Count                      : 7
Create Date                     : 2017:11:03 11:03:49+08:00
Title                           : Microsoft Word - SZEM170900985504 MPE .docx
Producer                        : GPL Ghostscript 8.64
Author                          : kate_bian
Creator                         : PScript5.dll Version 5.2.2
Modify Date                     : 2017:11:03 03:03:49Z