02 Bluetooth Smart Module User Manual Users Manual Branchpoint Technologies, Inc.

Branchpoint Technologies, Inc. Bluetooth Smart Module

Page 1 of 02 Bluetooth Smart Module User Manual Users Manual Branchpoint Technologies, Inc.
Page 2 of 02 Bluetooth Smart Module User Manual Users Manual Branchpoint Technologies, Inc.

Title:
PN EC-0137 RF Module User’s Manual
DOC #:
DCR #:
Rev:
18-0169
N/A
Bx1
1. Introduction
This user’s manual is for internal use at Branchpoint Technologies, Inc. and is for use by
Branchpoint engineers integrating PN EC-0137, 2.4GHz RF module into Branchpoint products.
2. Regulatory Information
2.1. Federal Communications Commission (FCC)
2.1.1. FCC Notices
Any changes or modifications not expressly approved by Branchpoint Technologies may void
the user’s authority to operate the equipment.
PN EC-0137 including the antennas, which are listed below, complies with Part 15 of the FCC
Rules.
The device meets the requirements for modular transmitter approval as detailed in FCC public
Notice DA00-1407. The transmitter operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
THIS DOCUMENT IS THE PROPERTY OF BRANCHPOINT TECHNOLOGIES AND SHALL NOT BE
REPRODUCED, DISTRIBUTED, DISCLOSED OR USED WITHOUT THE EXPRESSED WRITTEN CONSENT OF
BRANCHPOINT TECHNOLOGIES. ©2018 & IN YEAR PUBLISHED. ALL RIGHTS RESERVED.
Page:
1 of 2
Title:
PN EC-0137 RF Module User’s Manual
2.1.2. Approved Antenna List
Part Number
Manufacturer
Frequency Band
LDA212G3110K Murata
2.4 GHz
ANT2012
Yageo
2.4 GHz
DOC #:
DCR #:
Rev:
18-0169
N/A
Bx1
Type
Chip antenna
Chip antenna
Gain (dBi)
+0.9dBi
+0.9dBi
2.1.3. RF Exposure
To comply with FCC RF Exposure requirements, the OEM must ensure that only antennas from
the Approved Antenna List are installed.
The preceding statement must be included as a CAUTION statement in manuals for products
operating with the approved antennas in the previous table to alert users on FCC RF Exposure
compliance.
Any notification to the end user of installation or removal instructions about the integrated radio
module is not allowed.
The radiated output power of PN EC-0137 with a mounted ceramic antenna (FCC ID: 2AJW602)
is below the FCC radio frequency exposure limits. Nevertheless, PN EC-0137 shall be used in
such a manner that the potential for human contact during normal operation is minimized.
End users may not be provided with the module installation instructions. OEM integrators and
end users must be provided with transmitter operating conditions for satisfying RF exposure
compliance.
The antenna used for this transmitter must be installed to provide a separation distance of at least
5mm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter.
3. Label
Each module is labeled as follows:
4. Technical Information
Refer to the Panasonic PAN1740 datasheet and the Dialog Semiconductors DA14580 datasheet
and application notes.
THIS DOCUMENT IS THE PROPERTY OF BRANCHPOINT TECHNOLOGIES AND SHALL NOT BE
REPRODUCED, DISTRIBUTED, DISCLOSED OR USED WITHOUT THE EXPRESSED WRITTEN CONSENT OF
BRANCHPOINT TECHNOLOGIES. ©2018 & IN YEAR PUBLISHED. ALL RIGHTS RESERVED.
Page:
2 of 2
Download: 02 Bluetooth Smart Module User Manual Users Manual Branchpoint Technologies, Inc.
Mirror Download [FCC.gov]02 Bluetooth Smart Module User Manual Users Manual Branchpoint Technologies, Inc.
Document ID3994149
Application IDZzVadybiGt4v5Nr70VXuew==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize10.52kB (131448 bits)
Date Submitted2018-09-06 00:00:00
Date Available2018-09-06 00:00:00
Creation Date2018-09-05 14:27:05
Producing SoftwareMicrosoft® Word 2016
Document Lastmod2018-09-06 12:12:46
Document TitleUsers Manual
Document CreatorMicrosoft® Word 2016
Document Author: BPT_NH

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Author                          : BPT_NH
Create Date                     : 2018:09:05 14:27:05-07:00
Modify Date                     : 2018:09:06 12:12:46-04:00
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Microsoft® Word 2016
Format                          : application/pdf
Creator                         : BPT_NH
Creator Tool                    : Microsoft® Word 2016
Metadata Date                   : 2018:09:06 12:12:46-04:00
Document ID                     : uuid:97DB405E-2126-4A25-AFC8-13895E0248C4
Instance ID                     : uuid:44b333cf-dc82-4a5a-81e9-dba3c7634981
Page Count                      : 2