PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.

Paralenz Group ApS. DIVE CAMERA

Page 1 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 2 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 3 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 4 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 5 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 6 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 7 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 8 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 9 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 10 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 11 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 12 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 13 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 14 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 15 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 16 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 17 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 18 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 19 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 20 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 21 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Page 22 of PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.

PARALENZ®
DIVE CAMERA
USER MANUAL
V3
PDC-1
www.paralenz.com
facebook.com/paralenz
WWW.PARALENZ.COM
Together with our users we design and develop high
quality products and solutions – built for a purpose.
TABLE OF CONTENTS
1.
1.1
1.2
1.3
1.3.1
1.3.2
Overview
What’s in the box?
Names of parts
Buttons
Activation Switch
Selector Ring
5.
Custom Mode
5.1	Mode screen appearance
5.2	Record video, slow
motion or time lapse
5.3
Take a photo burst
6.
Camera settings
6.1
Settings menu
2.
Getting started
6.2
Turn WiFi on/off
2.1
Attach wrist strap
6.3
White balance (WB)
2.2
Insert micro SD card
DCC™ (Depth Color Correction)
2.3
Remove micro SD card 6.4	
6.4.1	What
is DCC™?
2.4
Charge the battery
6.4.2	
Which
DCC setting to use?
2.5
Power on
6.5
Video settings
2.6
Power off
6.5.1 Video resolution
6.5.2 Frames per second
3.
Video Mode
6.6
Custom settings
3.1
Record video
6.6.1 Custom video
3.2
Video screen
6.6.2 Slow motion
3.3
What is a tag?
6.6.3 Time-lapse
3.4
Make tags in video
6.6.4 Photo burst
6.6.5 Visual overlay
4.
Photo & Snap record
6.7
Advanced settings
4.1
Take a photo
6.7.1
Format micro SD-card
4.2
Record a snap video
6.7.2	
Which version of firmware
4.3 	What is a snap video?
is installed on the camera?
4.4	Photo & Snap video
6.7.3	
Reset settings on the
record screen
camera
6.7.4
6.7.5
6.7.6
Flip display
Choose units
Zero depth
7.
7.1
7.2
7.3
Mounts
Included mounts
The T-rail click system
The Mask Mount
8.
8.1
8.1.1
8.1.2
Maintenance
Cleaning the camera
Cleaning the O-rings
How do I prevent the
camera from flooding?
Cleaning the switches
Cleaning the lens
Transporting the
camera
8.1.3
8.1.4
8.2
9.
Replacing parts
9.1
Replacing the lens
9.2	Replacing the O-rings
on the lens
9.3
Other spare parts
10.
10.1
10.2
10.3
10.4
USB Cable
View your content
11.
11.1
Software updates
Camera firmware
updates
12.
12.1
Battery
Charging the battery
13.
Troubleshooting
14.
Regulatory info
15.
Support
16.
Specifications
17.
Precautions
18.
Warranty
Download content
The ParalenzDive App
Micro SD-card
1. OVERVIEW
1.2 NAMES OF PARTS
Logo plate
1.1 WHAT’S IN THE BOX?
These items are included in your Paralenz Dive Camera box.
Lens lock ring
End cap
T-Rails
Lens
Activation switch
O-Rings
Selector ring
1. Paralenz Dive Camera
Lens end cap window
Threads
Eyelet
2. Mask Mount
3. Universal Mount
4. Wrist strap
5. USB-C cable
Micro SD card slot
6. 3 x O-rings
USB-C port
7. Protection pouch
8. Silicone grease
OLED user interface display
Intended use:
The Paralenz Dive Camera is intended to be used under water
– particularly for diving.
1.3 BUTTONS
2. GETTING STARTED
1.3.1 Activation Switch
Pull back the activation switch once and release quickly to
‘click’. Hold the activation switch for 1 second or more to ‘hold’.
2.1 ATTACH WRIST STRAP
1) Put the small cord of the strap through the eyelet on the
camera. 2) Put the other end of the strap through the loop.
3) Tighten the strap.
1.3.2 Selector Ring
To switch between modes, rotate the selector ring. The icon
aligned with the logo plate is the selected mode. Make sure the
selector ring is placed correctly (the selector ring will snap to
each position).
2.2 INSERT MICRO SD CARD
Power
Turn off the camera before inserting the micro SD card. Use only
class U3 or V30 SD cards of a well-known brand. A capacity of
32 GB or more is recommended. (Max. 128 GB) (NOT included)
1) Unscrew the end cap. 2) Insert the micro SD card (logo side up).
3) Screw the end cap on – do not cross thread the cap!
Video
Photo &
Snap record
Locked
Custom
You can select mode by
rotating the ring and align the
mode with the logo plate.
Settings
2.3 REMOVE MICRO SD CARD
2.5 POWER ON
Turn the camera off before removing the card.
1) Unscrew the end cap. 2) Push the micro SD card in, them
release it and pull out the card. 3) Screw the end cap on – do not
cross thread it and do not push the O-rings out of place.
Rotate the selector ring to power mode position and hold the
activation switch for 4 seconds to turn on the camera. The
display will show the Paralenz logo and the camera will vibrate.
When the camera is ready to use, the display will show the Home
screen. This screen will show battery level, SD card storage level,
WiFi status and DCC™ status.
4 sec.
2.4 CHARGE THE BATTERY
You may use a variety of devices to charge your camera.
Use a charger with 2.0 A output
or higher for the minimum
charging time.
Turn on camera
2.6 POWER OFF
Rotate the selector ring to the power mode and hold the activation switch for 4 seconds to turn off the camera. The display
says ‘GOODBYE’. When the display turns black, the camera has
turned off.
4 sec.
A. Charger in AC outlet
B. Power Bank
Turn off camera
C. USB in computer
3. VIDEO MODE
3.3 WHAT IS A TAG?
If you record for a long time, a tag will let you find that spot in a
long video. The Paralenz app lets you find tags in a long video.
3.1 RECORD VIDEO
1) Select the video mode on the selector ring.
2) Hold the activation switch for 1 second to start recording.
3) To stop recording, hold the activation switch for 1 second.
1 sec.
1 sec.
Go to paralenz.com/dive-log-app to download the app.
3.4 MAKE TAGS IN VIDEO
To make tags, click the activation button while recording a
video. When a tag has been inserted ‘TAG’ will appear on the
display.
Start
Stop
Click
3.2 VIDEO SCREEN
The video screen will appear when the video mode is selected.
Time
Battery level
Resolution
Frames per second
If you use flashlights or floodlights when diving, turn off DCC™.
Click three times to turn off/on the DCC™. The screen will show
the DCC™ status. For more information on DCC™ go to section 6.3.
10
11
4. PHOTO & SNAP RECORD
4.3 WHAT IS A SNAP VIDEO?
4.1 TAKE A PHOTO
Snap record is a easy way to switch between pictures and
video recording. You only record and photograph what you
want to.
1) Select the photo & snap record-mode on the selector ring.
2) Click the activation switch to take a picture.
4.4 PHOTO & SNAP VIDEO RECORD SCREEN
The photo & snap record-screen will appear when the mode is
selected.
Click
Mode
Battery
Image format
Photos taken
Take picture
4.2 RECORD A SNAP VIDEO
1) Select the photo & snap record-mode on the selector ring
2) Hold and keep holding the activation switch to record
3) Release the activation switch to stop the recording
Hold
12
Record video
If you use flashlights or floodlights when diving, turn off DCC™.
Click three times to turn off/on the DCC™. The screen will show
the DCC™ status. For more information on DCC™ go to section 6.3.
Release
Stop
13
5. CUSTOM MODE
5.2 RECORD VIDEO, SLOW MOTION
OR TIME-LAPSE
To record a video, slow motion or time-lapse 1) the custommode icon on the selector ring should be selected (make sure
that the right custom mode is selected. 2) Hold the activations
button for 1 second to start the recording. 3) To stop a recording, hold the activation button for 1 second.
5.1 MODE SCREEN APPEARANCE
The custom mode-screen will appear when the mode is
selected.
Mode
Battery level
1 sec.
Resolution
1 sec.
Frames per second
If you use flashlights or floodlights when diving, turn off DCC™.
Click three times to turn off/on the DCC™. The screen will show
the DCC™ status. For more information on DCC™ see section 6.4.
The screen can have 1 of 4 different modes assigned to it: video,
slow motion, time lapse and photo burst. Go to settings to see
how to switch between different custom modes (See chapter 6
– Camera settings).
Start
Stop
5.3 TAKE A PHOTO BURST
To take a photo burst, click the activation switch. A screen will
appear indicating that the camera is taking a photo burst. The
camera is ready to use again when that screen disappears.
Click
Video
14
Slow motion
Time lapse
Photo burst
15
6. CAMERA SETTINGS
The settings screen categories are as follows.
Go to the settings mode on the selector ring to select the camera settings (all settings can also be controlled via the app).
6.2 TURN WIFI ON/OFF
To change WiFi status go to settings > WiFi. Hold to turn WiFi
on/off.
Hold
6.1 SETTINGS MENU
When you select Settings on the selector ring, a menu will
appear. The first menu consists of 7 different categories: WiFi,
WB/DCC™, Video, Photo, Custom, Overlay and Advanced. You
navigate the menu by clicking or holding the activation switch.
Click once to go to the next step in the menu - hold to choose
or enter the selected setting.
Click
Next step
16
6.3 WHITE BALANCE (WB)
To set the Kelvin (K) value of the white balance, go to the WB/
DCC™ screen in the settings menu. Select 'Set WB'. You can
chose between Auto, 3500K, 5000K (default value) and 6500K.
Hold
Choose selected
For best results use the white balance only when you dive with
lights on. For more information on how to use the white balance
go to www.paralenz.com/support
17
6.4 
DCC™ (DEPTH CONTROLLED COLOR
CORRECTION)
6.4.1 What is DCC™ ?
DCC™ is an intelligent version of a color filter, which are normally made from plastic and placed in front of your camera lens,
to remove the green or blue taint in your videos. It is controlled
by the pressure sensor and adjusts the strenght of the filter to
match the depth you are at.
Toggle either DCC™ or WB on/off by clicking three times on the
activation switch while in power- or video-mode.
6.5 VIDEO SETTINGS
In video settings you can select resolution and frames per second.
To change the DCC™ state, go to the WB/DCC™ screen in the
settings menu. Hold to enter the WB/DCC™ menu. Hold the
activation switch to activate the blue or green DCC setting.
6.5.1 Video resolution
The deeper you go the more colors will be absorbed. The
camera cannot add colors that are not present, so beyond 20
meters de-activate the DCC™ and use a flashlight instead. For
more information on DCC™ go to www.paralenz.com/support
6.4.2 Which DCC setting to use?
If the water is blue, we recommend you use DCC: blue. If the
water is green, we recommend you use DCC: green.
6.5.2 Frames per second
Notice that there are limits to how high the FPS can be at
higher resolutions.
6.6 CUSTOM SETTINGS
The custom settings lets you control the following:
The water is blue – use DCC: blue
18
The water is green – use DCC: green
19
6.6.1 Custom video
You can change the video mode on the camera. If you want
to record for a longer time, select 1080P as the normal video
mode, but if there’s something you want to record in 4K, you
can assign it to the custom mode.
To activate this mode just select the ‘activate-screen’ and hold
to assign it to the custom mode. The settings in custom video
are the same as in normal video.
6.6.3 Time-lapse
To activate time-lapse mode just select the ‘activate-screen’
and hold to assign it to the custom mode. In settings you can
select your resolution and time interval between the pictures
taken.
6.6.2 Slow motion
To activate slow motion mode, select the ‘activate-screen’
and hold to assign it to the custom mode. In settings, you can
change the resolution and frames per second.
20
21
6.6.4 Photo burst
To activate photo burst mode select the ‘activate-screen’ and
hold to assign it to the custom mode. In settings you can select how many images are taken per amount of time.
6.6.5 Visual overlay
The visual overlay embeds depth and temperature to your
videos or your photos. To activate visual overlay select 'overlay'
in the main settings menu. Here you can turn the visual overlay
on and off. Note that a visual overlay cannot be removed after
being embedded in a media file.
6.7 ADVANCED SETTINGS
The advanced settings allows you to 1) format the SD-card
2) see which firmware is on the camera 3) reset settings on
the camera 4) flip the display and 5) choose units.
6.7.1 Format micro SD-card
If ‘format’ is selected, you must confirm that you want to format the micro SD-card.
Reformatting the SD-card will delete all data, so make sure to
save the footage you want to keep on your computer before
reformatting the card.
6.7.2 Which version of firmware is installed on the camera?
If ‘firmwr’ (firmeware) is selected, the version number will be
shown for a short period of time.
Example of visual overlay embedded
22
23
6.7.3 Reset settings on the camera
If ‘reset’ is selected, you must confirm that you want to reset
the settings on the camera to factory defaults.
6.7.4 Flip display
If you’re mounting the camera upside down, this function
allows you to flip the OLED display and the image.
6.7.5 Choose units
This function allows you to choose which units of measure to
display.
7. MOUNTS
7.1 INCLUDED MOUNTS
There are two mounts in the box; The Universal Mount and the
Mask Mount. The Universal Mount enables you to use most
of the existing accessories on the market. The Mask Mount is
designed to fit all regular diving masks
Universal Mount
Mask Mount
7.2 THE T-RAIL CLICK SYSTEM
6.7.6 Zero depth
The Zero depth function lets you calibrate the depth sensor
inside your Paralenz Dive Camera to zero. You can use this
function if you should experience that the sensor is slightly off
in your dive logs and the corresponding media.
Press the center of the mount and the top of the camera
together to fasten the camera to the mount. Make sure both
latches are fastened correctly. Do not use excessive force.
*Click*
*Click*
Make sure that both sides are fastened
24
25
8. MAINTENANCE
8.1 CLEANING THE CAMERA
Do not push up on the latch releases.
If you do, the camera will not be attached
correctly.
7.3 THE MASK MOUNT
Put the mask strap through the slots of the Mask Mount.
The Mask Mount can be used on either side of your mask.
8.1.1 Cleaning the O-rings
Always clean the camera in fresh water after use. Check that
the O-rings have not been stretched and that they do not have
any cuts or tears. To lubricate the O-rings apply grease that
does not contain silicone and run them through your fingers
while gently rubbing the grease into the O-ring (do not use
spray lubricant or petroleum based grease).
8.1.2 How do I prevent the camera from flooding?
The triple O-rings are tested to 200 m/656 ft./21 ATM. , so as
long as you properly maintain the O-rings and don’t open the
camera below water you are fine. Remember to screw on the
end cap correctly.
8.1.3 Cleaning the switches
If sand grains get stuck underneath the magnetic switches,
you can easily remove the switches with a small Allen key,
rinse in fresh water, and put them back on. Go to paralenz.com
for more info.
8.1.4 Cleaning the lens
To clean the lens, wipe it with a soft, lint-free cloth. You can use
Eyeglass Cleaning Fluid – but do not use strong solvents such
as benzene or alcohol.
8.2 TRANSPORTING THE CAMERA
26
Use the supplied protection pouch when transporting your
Paralenz Dive Camera. There is also room for cables, SD-cards
and silicone grease for the O-rings in the pouch.
27
9. REPLACING PARTS
9.2 REPLACING THE O-RINGS ON THE LENS
9.1 REPLACING THE LENS
If the O-rings are damaged you can replace them: 1)Unscrew
the lens lock ring. 2) Replace the O-ring with the extra O-ring
that came with your camera. Remember to apply grease that
does not contain silicone.
If the lens is damaged you can buy a Paralenz Lens Kit. To
replace the lens: 1) Unscrew the lens lock ring by rotating it
counter clockwise. 2) Loosen the front lens with your fingers.
3) Apply grease that does not contain silicone around the
O-rings on the new lens. 4) Insert the new lens while rotating
slightly.
Make sure that the O-rings are aligned and lubricated. If they
are misplaced or dried out the camera will be flooded.
9.3 OTHER SPARE PARTS
For other spare parts please contact support@paralenz.com
28
29
10. DOWNLOAD CONTENT
11. SOFTWARE UPDATES
10.1 THE PARALENZDIVE APP
11.1 CAMERA FIRMWARE UPDATES
The free ParalenzDive App makes downloading, sharing and
viewing your photos and recordings easy. Download the app
via App Store/Google Play. The app will guide you through the
connection process.
Firmware updates are made through the ParalenzDive App.
The app will give a notification when a new update is available.
10.2 MICRO SD-CARD
You can also download all firmware updates on
www.paralenz.com/support. To install the firmware manually
follow these steps:
You can also transfer your data from your micro SD-card by
inserting the card into a card reader. See section 2.3 for information on how to remove the micro SD-card.
10.3 USB CABLE
By connecting your camera to a computer via the USB-C cable,
you can access the content on the camera. Choose ‘data’
when connecting to the computer.
10.4 VIEW YOUR CONTENT
For viewing your video content, use programs such as Windows Media Player, VLC Player, Quicktime etc.
30
Download the app via App Store/Google Play.
1. Delete any file named “firmware.bin” in the folder you
choose to download to.
2. Download the latest firmware for your camera on this page.
3. C
 opy the file firmware.bin onto the root of an empty SD-card
(Not in a folder).
4. Make sure the battery has at least 70% power left. This is essential. You risk breaking your camera if this is not followed.
Unplug the camera from the charger before checking the
power percentage.
5. Turn off the camera. Insert the SD-card into the slot.
6. Turn the camera on until you see the logo and wait for it to
turn off automatically. (The camera is now downloading the
new firmware).
7. Turn the camera on again and wait for it to turn off
automatically (The camera is now installing the firmware).
8. The camera is now ready to be turned on, with the new firmware installed.
31
12. BATTERY
13. TROUBLESHOOTING
The Paralenz Dive Camera comes with an integrated LiPo 1600
mAh battery.
13.1 What to do if the camera should freeze or won't turn on
In case of the camera freezing and not responding, you can
always do a hard-reset:
1. Turn the selector ring to power position.
2. Plug in the charger.
3. Hold the activation switch for 10 seconds.
- The camera will now reboot.
12.1 CHARGING THE BATTERY
Use the included USB-C cable for charging. Charge the camera
through your computer or use a wallcharger – preferably a 2.1 A
USB power adapter. See section 2.4 for information about how
to charge the battery.
WARNING: Do not use the camera or the battery if it has been
damaged – for example, if cracked or punctured. Disassembling or puncturing the battery can cause an explosion or fire.
Do not store the camera where prolonged exposure to
extreme temperatures can occur, because it can cause
permanent damage. Do not dry the camera or battery with an
external heat source such as a microwave oven or hair dryer.
Do not store your battery with metal objects. If the battery
terminals come in contact with metal objects, the battery
may “shortout” and cause a fire.
32
13.2 If the SD-card needs to be reformatted
When formatting the memory card on a PC/MAC it needs to be
formatted with the FAT32 format (32kb) for up to 32 GV and exFAT for 64 GB cards.
The SD-card can also be reformatted through the camera. See
section 6.7.1 for information on how to format.
Reformatting the SD-card will delete all data, so make sure to
save the footage you want to keep on your computer before
reformatting the card.
33
14. REGULATORY INFO
CE mark indicates that this product complies with the
European requirements for safety, health, environment and
customer protection.
This symbol indicates separate collection of waste batteries
in the EU countries. Please do not throw the batteries into
domestic refuse. Please use the return and collection
systems available in your country for the disposal of waste
batteries.
The RCM is the compliance mark for all applicable Australian Communications and Media Authority (ACMA) regulatory arrangements, including all technical and record-keeping
requirements.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by Paralenz is under license.
The Wi-Fi CERTIFIED logo is a registered trademark of the
Wi-Fi Alliance.
iOS and App Store are registered trademarks of Apple Inc.
Android and Google Play are registered trademarks of
Google Inc.
34
FCC
a. This device complies with Part 15 of FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
b. Warning: Changes or modifications to this unit not expressly
approved by the part responsible for compliance could void
the user’s authority to operate the equipment.
c. NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for
help.
35
d. This device is also designed to meet the requirements for
exposure to radio waves established by the Federal Communications Commission (USA). The SAR limit adopted by the USA
is 1.6 W/kg averaged over one gram of tissue. The highest SAR
value reported to the FCC for this device type complies with
this limit.
15. SUPPORT
Paralenz is dedicated to providing the best possible service.
To reach our Customer Support, visit paralenz.com/support or
contact support@paralenz.com
IC
a. This device complies with CAN ICES-3 (B)/NMB-3(B).
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference
that may cause undesired operation of the device.
b. Cet appareil est conforme à la norme CAN ICES-3 (B)/NMB3 (B).
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. Son
fonctionnement est soumis aux conditions suivantes : (1)
l'appareil ne doit pas causer d'interférence et (2) l'appareil
doit accepter toute interférence, y compris une interférence
pouvant entraîner un fonctionnement non désiré.
The frequency band(s) in which the radio equipment operates;
maximum radio-frequency power transmitted in the frequency
band(s) in which the radio equipment operates.
2.4 GHz Wi-Fi
2402-2480 MHz for BT
Maximum radio power: <20 dBm for 2.4 GHz Wi-Fi, <10 dBm
for BT
36
37
16. SPECIFICATIONS
Waterproof to
Video resolution
Still resolution
White balance
Battery life
EIS - Electronic image
and tilt stabilization
App
200 M/656 FT./21 ATM.
4k-30 fps / 1080p-100 fps / 720p-240 fps
8 MP
Auto, 3500K, 5000K, 6500K + DCC™ (switch between WB and DCC™)
LiPo – 1600 mAh / 3+ hours recording (1080 p – 30 fps)
Will be available soon through firmware update
Viewing / Sharing / Settings (iOS & Android)
Usable with gloves
Yes
Shockproof
Yes
Lens / lens distortion
correction
Weight
Dimensions
Housing
update
155 g (5.5 oz)
116 x 35 x 38 mm (4.5 x 1.4 x 1.5”)
Military grade aluminum & polycarbonate
Audio recording
Yes (internal microphone)
Port
USB-C (for fast charging)
Storage
128 GB micro SD-card max. (Class: U3 or V30) – not included
Mounts
Mask Mount & Universal Mount included
Dive log video overlay
Connectivity
Display
Operating temperature
Extra casing needed
Sensors
38
140° / lens distortion correction will soon be available through firmware
Yes
WiFi, Bluetooth & USB
0.5” OLED
-20°C to 85°C / -4°F to 185°F / EVA padding (minimizing battery
discharge in cold water)
No
Pressure / temperature
17. PRECAUTIONS
To avoid malfunction, explosion, or fire:
Do not microwave, open, drop, puncture, take apart, bend,
crush, paint, or incinerate the camera.
Do not solder or glue parts onto the camera and do not insert
foreign objects into any openings, such as the Micro USB port.
 o not use the camera if it is damaged, this includes a puncD
ture, missing O-ring, or water inside and do not attempt to
remove or change the battery.
 o not dry the camera in an oven, with a hairdryer or any other
external heat source, especially open fire.
Do not use the Paralenz Dive Camera for dives deeper than
200M/556F/21 ATM.
 hen opening and charging the camera, make sure that your
hands are not wet, and that water from other sources cannot
enter the camera or charger. This may cause electrical shock.

The
Paralenz Dive Camera should not in any way be used as a
dive computer, or as a supplement to a dive computer.
When charging, make sure the charger is a USB type charger,
of max 5V, or use a USB plug on a computer.
If the front lens on the Paralenz Dive Camera should break,
take care to avoid injury. Keep out of reach of children.
39
18. WARRANTY
The warranty covers all manufacturing defects and faults in
design. During the warranty period, Paralenz will replace any
defective units with a new or refurbished unit at our disgression
The warranty does not cover depletion of the battery or results
from normal wear and tear. It also does not cover unauthorized
repairs, negligence, improper use or accidents.
The warranty period begins from the date of purchase.
The warranty does not cover commercial or rental use.
In case you experience any fault with the Paralenz Dive Camera
in the warranty period, please go to www.paralenz.com/support
and fill in a warranty claim, to start the replacement process.
For further information on how the warranty applies to your
country please visit www.paralenz.com/support.
FCC ID: 2AL8V-PDC1A
IC: 22808-PDC1A
Applicant:
Paralenz Group ApS.
Refshalevej 163a ST.MF, Copenhagen K, 1432 Denmark
40
For more information, visit
WWW.PARALENZ.COM
Download: PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Mirror Download [FCC.gov]PDC1A DIVE CAMERA User Manual Users Manual Paralenz Group ApS.
Document ID3595008
Application IDqv2k+BEW0CTnKDMifkmJ6Q==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize406.69kB (5083628 bits)
Date Submitted2017-10-09 00:00:00
Date Available2017-12-30 00:00:00
Creation Date2017-09-06 13:37:23
Producing SoftwareAdobe PDF Library 15.0
Document Lastmod2017-09-06 13:37:37
Document TitleUsers Manual
Document CreatorAdobe InDesign CC 2017 (Macintosh)

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Language                        : en-US
XMP Toolkit                     : Adobe XMP Core 5.6-c138 79.159824, 2016/09/14-01:09:01
Create Date                     : 2017:09:06 13:37:23+02:00
Metadata Date                   : 2017:09:06 13:37:37+02:00
Modify Date                     : 2017:09:06 13:37:37+02:00
Creator Tool                    : Adobe InDesign CC 2017 (Macintosh)
Instance ID                     : uuid:f178f680-8317-664a-90fd-04aaf3622616
Original Document ID            : xmp.did:b33e827f-1efd-44a3-82fe-196b91e7f065
Document ID                     : xmp.id:6aac43cf-5761-4591-a6d7-1bac95f7462c
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:170e53ee-be14-4a37-b561-f082ce488b00
Derived From Document ID        : xmp.did:170e53ee-be14-4a37-b561-f082ce488b00
Derived From Original Document ID: xmp.did:b33e827f-1efd-44a3-82fe-196b91e7f065
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2017 (Macintosh)
History Changed                 : /
History When                    : 2017:09:06 13:37:23+02:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 22
Creator                         : Adobe InDesign CC 2017 (Macintosh)