TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC

Horizon Hobby, LLC AR410Receiver

Page 1 of TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Page 2 of TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Page 3 of TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Page 4 of TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Page 5 of TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Page 6 of TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Page 7 of TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Page 8 of TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Page 9 of TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Page 10 of TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Page 11 of TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Page 12 of TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Page 13 of TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC

AR410 User Guide
AR410 Bedienungsanleitung
Guide de L’utilisateur - AR410
AR410 Guidea Dell’utente
EN
NOTICE
All instructions, warranties and other collateral documents are subject to
change at the sole discretion of Horizon Hobby, LLC. For up-to-date product
literature, visit horizonhobby.com and click on the support tab for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate
various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability
of property damage, collateral damage, and serious injury OR create a high
probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the probability
of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of
physical property damage AND a little or no possibility of injury.
WARNING: Read the ENTIRE instruction manual to become familiar
with the features of the product before operating. Failure to operate
the product correctly can result in damage to the product, personal
property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution
and common sense and requires some basic mechanical ability. Failure to
operate this Product in a safe and responsible manner could result in injury
or damage to the product or other property. This product is not intended for
use by children without direct adult supervision. Do not attempt disassembly,
use with incompatible components or augment product in any way without
the approval of Horizon Hobby, LLC. This manual contains instructions for
safety, operation and maintenance. It is essential to read and follow all the
instructions and warnings in the manual, prior to assembly, setup or use, in
order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
WARNING AGAINST COUNTERFEIT PRODUCTS
Always purchase from a Horizon Hobby, LLC authorized dealer to ensure
authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims
all support and warranty with regards, but not limited to, compatibility and
performance of counterfeit products or products claiming compatibility with
DSM or Spektrum technology.
NOTICE: This product is only intended for use with unmanned, hobby-grade,
remote-controlled vehicles and aircraft. Horizon Hobby disclaims all liability outside
of the intended purpose and will not provide warranty service related thereto.
WARRANTY REGISTRATION
Visit www.spektrumrc.com/registration today to register your product.
EN
AR410 4-Channel Telemetry Receiver
The Spektrum™ AR410 receiver is a full
range telemetry receiver featuring DSM®
technology and is compatible with all
Spektrum™ and JR® aircraft radios that
support DSM2® and DSMX® technology.
The AR410 receiver features fly-by
telemetry data for flight log information
as well as receiver battery voltage. This
allows flight log and receiver voltage to be
displayed on telemetry capable Spektrum
transmitters in fly-by range, typically 300-400 feet.
For information on Spektrum Telemetry Sensors visit:
http://www.spektrumrc.com
The AR410 is not compatible with the Flight Log, SPM9540. Flight Log
information is only available through a Spektrum Telemetry capable transmitter.
AR410
Type
Dimensions (L × W × H)
Antenna Length
Channels
Weight
Band
Voltage Range
4-Channel Sport Receiver
45.2 × 20.0 × 13.9mm
Internal
7g
2.4GHz
3.5–9V
A: Bind Button
B: Battery port
C: Servo ports (4)
D: 1/DATA: Servo port 1 and DATA
B D
EN
AR410 Antenna
The AR410 features an internal antenna design for easy installation in almost any
model.
Receiver Installation
Installing the Receiver
Install the receiver in the normal position recommended by the airplane’s
manufacturer. Double-sided tape or foam can be used to secure the receiver
in place.
Binding
The AR410 receiver must be bound to the transmitter before they will operate.
Binding is the process of teaching the receiver the specific code of the
transmitter so it will only connect to that specific transmitter.
1. Push and hold the bind button on the receiver while powering up the
receiver. Release the Bind button once the orange LED starts to flash
continuously, indicating that the receiver is in bind mode. The receiver will
also enter bind mode if you power on the receiver and then press the bind
button before the receiver has connected to any transmitter.
2. Put your transmitter in bind mode.
3. The bind process is complete when the orange LED on the receiver is solid.
4. After you set up your model, always rebind the transmitter and receiver to
set the desired failsafe positions. See FAILSAFE on the next page.
Failsafe
Failsafe position is set during binding. In the unlikely event that the radio link
is lost during use, the receiver will drive all channels to its pre-programmed
failsafe position.
SmartSafe + Hold Last
Preset Failsafe
If loss of signal occurs, SmartSafe™
technology moves the throttle channel
to its preset failsafe position (low
throttle) that was set during binding.
All other channels hold their last
position. When the receiver detects
signal from the transmitter, normal
aircraft operation resumes.
Preset failsafe is ideal for sailplanes,
allowing the aircraft to automatically
dethermalize if the signal is lost. With
preset failsafe, all channels go to their
preset failsafe positions if the signal
is lost, preventing a flyaway. When
the receiver detects signal from the
transmitter, normal aircraft operation
resumes.
EN
SmartSafe + Hold Last
Lower Throttle on transmitter
Push and Hold Bind Button
Power on Reciever
Release Button once RX goes into Bind Mode (flashing LED)
Place transmitter in Bind Mode and finish Binding.
Preset Failsafe
Move all sticks and switches on the transmitter to desired Failsafe position.
Push and Hold Bind Button
Power on Reciever
Release Button after RX goes into Bind Mode (flashing LED)
Push and Hold the Bind Button again before the transmitter enters Bind Mode.
Testing Failsafe
Secure the aircraft on the ground and remove the propellers. Test Failsafe
by turning the transmitter off and noting how the receiver drives the control
surfaces.
Receiver Power Only
• With SmartSafe or Preset Failsafe, when the receiver only is turned on (no
transmitter signal is present), the throttle channel has no output, to avoid
operating or arming the electronic speed control.
• All other channels have no output until the receiver has linked to the transmitter.
Range Testing
Before each flying session and especially with a new model, it is important to
perform a range check. All Spektrum aircraft transmitters incorporate a range
testing system which, when activated, reduces the output power, allowing
a range check.
1. With the model restrained on the ground, stand 30 paces (approx. 90
feet/28 meters) away from the model.
2. Face the model with the transmitter in your normal flying position and place
your transmitter into range check mode.
3. You should have total control of the model with the button depressed at 30
paces (90 feet/28 meters).
4. If control issues exist, contact the appropriate product support department.
EN
Advanced Range Testing
For sophisticated models that have significant conductive material in them, the
Advanced range test using a flight log is recommended. The advanced range
check will confirm that the receiver is operating optimally and that the installation
is optimized for the specific aircraft.
1. Standing 30 paces away from the model, face the model with the transmitter in
your normal flying position.
2. Put your transmitter in range test mode. Range test mode reduces the power
output from the transmitter.
3. Have someone position the model in various orientations (nose up, nose down,
nose toward the transmitter, nose away from the transmitter, etc.).
4. Observe the telemetry on your transmitter. Note any orientations that cause
higher fade or hold values. Perform this step for at least one minute.
5. Re-position the receiver as necessary.
Receiver Power System Requirements
Inadequate power systems that are unable to provide the necessary minimum
voltage to the receiver during flight have become the number one cause of
in-flight failures. Some of the power system components that affect the ability
to properly deliver adequate power include:
• Receiver battery pack (number of cells, capacity, cell type, state of charge)
• The ESC’s capability to deliver current to the receiver in electric aircraft
• The switch harness, battery leads, servo leads, regulators etc.
The AR410 has a minimum operational voltage of 3.5 volts; it is highly
recommended the power system be tested per the guidelines below.
Recommended Power System Test Guidelines
If a questionable power system is being used (e.g. small or old battery,
ESC that may not have a BEC that will support high-current draw, etc.), it is
recommended that a voltmeter be used to perform the following tests.
The Hangar 9® Digital Servo & Rx Current Meter (HAN172) or the Flight Log on
your Spektrum telemetry capable transmitter is the perfect tool to perform the
test below.
Plug the voltmeter into an open channel port in the receiver and with the
system on, or simply monitor the voltage on a telemetry capable transmitter,
load the control surfaces (apply pressure with your hand) while monitoring the
voltage at the receiver. The voltage should remain above 4.8 volts even when
all servos are heavily loaded.
EN
How QuickConnect™ Techonlogy Works
• When the receiver voltage drops below 3.5 volts the system ceases to operate.
• When power is restored the receiver immediately attempts to reconnect.
• If the transmitter was left on, the system reconnects typically in about
4/100 of a second.
QuickConnect with Brownout Detection is designed to allow you to fly safely
through most short duration power interruptions, however, the root cause of
these interruptions must be corrected before the next flight to prevent a crash.
NOTICE: If a brownout occurs in flight it is vital that the cause of the
brownout be determined and corrected.
Important: Y-Harnesses and Servo Extensions
When using a Y-harness or servo extensions in your installation, it’s
important to use standard non-amplified Y-harnesses and servo extensions
as this can/will cause the servos to operate erratically or not function at
all. Amplified Y-harnesses were developed several years ago to boost the
signal for some older PCM systems and should not be used with Spektrum
equipment. Note that when converting an existing model to Spektrum be
certain that all amplified Y-harnesses and/or servo extensions are replaced
with conventional non-amplified versions.
ModelMatch™ Technology
Some Spektrum and JR transmitters offer a patent pending feature called
ModelMatch. ModelMatch technology prevents the possibility of operating a
model using the wrong model memory, potentially preventing a crash. With
ModelMatch, each model memory has its own unique code (GUID) and during
the binding process the code is programmed into the receiver. Later, when
the system is turned on, the receiver will only connect to the transmitter if the
corresponding model memory is programmed on screen.
If at any time you turn on the system and it fails to connect, check to be sure
the correct model memory is selected in the transmitter. Please note that the
DX5e and Aircraft Modules do not have ModelMatch technology.
EN
Frequently Asked Questions on Spektrum 2.4GHz
1. Q: After I’ve bound the receiver to my transmitter, which do I turn
on first when I want to fly?
A: Either one. Every DSM 2.4GHz transmitter has a GUID (Globally Unique
Identifier) code imbedded in its signal. When you bind a DSM receiver
to your transmitter, this GUID code is stored in the receiver. If you turn
the receiver on before the transmitter, you don’t have to worry about it
responding to another transmitter. The receiver will go into failsafe mode
while it waits for a signal from the transmitter with the same GUID code
it has stored. See the Receiver Power Only section for more information.
If a DSM transmitter is turned on first you can expect it to connect within
6 seconds of powering on the receiver.
2. Q: Sometimes the system takes longer to connect or doesn’t
connect at all. Why?
A: In order for a DSM system to connect, the receiver must receive a large
number of uninterrupted signal packets from the transmitter. This process
takes just a few seconds, but if the transmitter is too close to the receiver
(within 4 feet) or near reflective material (metal objects, carbon fiber
material, etc.) it may detect its own reflected 2.4GHz energy as “noise”.
This can delay or prevent connection. If this happens, make sure you are
a sufficient distance from metal objects and the receiver itself before you
power up and try again.
3. Q: How important is Flight Log information?
A: All 2.4GHz signals, not just DSM, are affected by proximity to
conductive materials such as carbon fiber or metal. If you are flying a
model that uses a lot of conductive materials in its construction, Flight
Log information can be helpful. The information collected when you fly
can help determine the optimum location for your receiver(s) so you can
minimize the effects of these materials on your signal performance.
EN
1-Year Limited Warranty
What this Warranty Covers - Horizon Hobby, LLC, (Horizon) warrants to the
original purchaser that the product purchased (the “Product”) will be free from
defects in materials and workmanship for a period of 1 year from the date of
purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii)
damage due to acts of God, accident, misuse, abuse, negligence, commercial
use, or due to improper use, installation, operation or maintenance, (iii)
modification of or to any part of the Product, (iv) attempted service by anyone
other than a Horizon Hobby authorized service center, (v) Product not purchased
from an authorized Horizon dealer, (vi) Product not compliant with applicable
technical regulations, or (vii) use that violates any applicable laws, rules, or
regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER
WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY
ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE
REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that
Horizon will, at its option, either (i) service, or (ii) replace, any Product determined
by Horizon to be defective. Horizon reserves the right to inspect any and all
Product(s) involved in a warranty claim. Service or replacement decisions are
at the sole discretion of Horizon. Proof of purchase is required for all warranty
claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS
THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR
ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of
Horizon exceed the individual price of the Product on which liability is asserted.
As Horizon has no control over use, setup, final assembly, modification or misuse,
no liability shall be assumed nor accepted for any resulting damage or injury. By
the act of use, setup or assembly, the user accepts all resulting liability. If you
as the purchaser or user are not prepared to accept the liability associated with
the use of the Product, purchaser is advised to return the Product immediately in
new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law
principals). This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state. Horizon reserves the right to change
or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support
or service. Once assembly, setup or use of the Product has been started, you
must contact your local distributor or Horizon directly. This will enable Horizon
to better answer your questions and service you in the event that you may
EN
need any assistance. For questions or assistance, please visit our website at
www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free
telephone number referenced in the Warranty and Service Contact Information
section to speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country
you live and use the Product in, please use the Horizon Online Service Request
submission process found on our website or call Horizon to obtain a Return
Merchandise Authorization (RMA) number. Pack the Product securely using a
shipping carton. Please note that original boxes may be included, but are not
designed to withstand the rigors of shipping without additional protection. Ship
via a carrier that provides tracking and insurance for lost or damaged parcels,
as Horizon is not responsible for merchandise until it arrives and is accepted at
our facility. An Online Service Request is available at http://www.horizonhobby.
com/content/service-center_render-service-center. If you do not have internet
access, please contact Horizon Product Support to obtain a RMA number along
with instructions for submitting your product for service. When calling Horizon,
you will be asked to provide your complete name, street address, email address
and phone number where you can be reached during business hours. When
sending product into Horizon, please include your RMA number, a list of the
included items, and a brief summary of the problem. A copy of your original
sales receipt must be included for warranty consideration. Be sure your name,
address, and RMA number are clearly written on the outside of the shipping
carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue
with a LiPo battery, please contact the appropriate Horizon Product
Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt verifying
the proof-of-purchase date. Provided warranty conditions have been met, your
Product will be serviced or replaced free of charge. Service or replacement
decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed and
payment will be required without notification or estimate of the expense unless
the expense exceeds 50% of the retail purchase cost. By submitting the item
for service you are agreeing to payment of the service without notification.
Service estimates are available upon request. You must include this request
with your item submitted for service. Non-warranty service estimates will be
billed a minimum of ½ hour of labor. In addition you will be billed for return
freight. Horizon accepts money orders and cashier’s checks, as well as Visa,
MasterCard, American Express, and Discover cards. By submitting any item to
Horizon for service, you are agreeing to Horizon’s Terms and Conditions found
on our website http://www.horizonhobby.com/content/service-center_renderservice-center.
ATTENTION: Horizon service is limited to Product compliant in the
country of use and ownership. If received, a non-compliant Product
will not be serviced. Further, the sender will be responsible for
arranging return shipment of the un-serviced Product, through a
carrier of the sender’s choice and at the sender’s expense. Horizon
will hold non-compliant Product for a period of 60 days from
notification, after which it will be discarded.
10-2015
10
EN
Warranty and Service Contact Information
Country of
Purchase
United States
of America
European
Union
Horizon Hobby
Contact Information
Horizon Service
Center
(Repairs and Repair
Requests)
servicecenter.horizonhobby.com/
RequestForm/
Horizon Product
Support
(Product Technical
Assistance)
productsupport@horizonhobby.com.
Sales
websales@horizonhobby.com
800-338-4639
Horizon Technischer
Service
sales@horizonhobby.eu
Sales: Horizon
Hobby GmbH
+49 (0) 4121 2655 100
Address
1608 Interstate Dr.
Champaign, Illinois,
61822 USA
877-504-0233
Hanskampring 9
D 22885 Barsbüttel,
Germany
FCC Information
FCC ID: BRWTASPMAR410
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTICE: Modifications to this product will void the user’s authority to
operate this equipment.
This product contains a radio transmitter with wireless technology which
has been tested and found to be compliant with the applicable regulations
governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
11
EN
IC Information
IC: 6157A-TASPMAR410
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, Including
interference that may cause undesired operation of the device.
Compliance Information for the European Union
Horizon Hobby, LLC hereby declares that this product is in
compliance with the essential requirements and other relevant
provisions of the RED Directive.
A copy of the EU Declaration of Conformity is available online at:
http://www.horizonhobby.com/content/support-render-compliance.
Instructions for Disposal of WEEE by Users in the
European Union
This product must not be disposed of with other waste. Instead, it
is the user’s responsibility to dispose of their waste equipment by
handing it over to a designated collection point for the recycling
of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal
will help to conserve natural resources and ensure that it is recycled in a manner
that protects human health and the environment. For more information about
where you can drop off your waste equipment for recycling, please contact your
local city office, your household waste disposal service or where you purchased
the product.
12
© 2018 Horizon Hobby, LLC.
DSM, DSM2, DSMX, QuickConnect, ModelMatch, SmartSafe, Hangar 9 and the Horizon Hobby logo
are trademarks or registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
JR is a registered trademark of JR Americas. All other trademarks, service marks and logos are
property of their respective owners.
Updated 06/18
57983.1
SPMAR410
Download: TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Mirror Download [FCC.gov]TASPMAR410 AR410Receiver User Manual BRWTASPMAR410_English _1 Horizon Hobby, LLC
Document ID3916501
Application IDoNREjq3UtzYRyTEaJ2+n4w==
Document DescriptionBRWTASPMAR410_English User Manual_1
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize15.42kB (192703 bits)
Date Submitted2018-07-09 00:00:00
Date Available2018-07-09 00:00:00
Creation Date2018-06-25 09:17:31
Producing SoftwareAcrobat Distiller 10.0.0 (Macintosh)
Document Lastmod2018-07-07 10:04:42
Document TitleBRWTASPMAR410_English User Manual_1
Document CreatorAdobe InDesign CS5.5 (7.5.2)
Document Author: tbrummett

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : tbrummett
Create Date                     : 2018:06:25 09:17:31-05:00
Modify Date                     : 2018:07:07 10:04:42+08:00
Page Count                      : 13
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : Adobe InDesign CS5.5 (7.5.2)
Metadata Date                   : 2018:06:25 09:27:14-05:00
Producer                        : Acrobat Distiller 10.0.0 (Macintosh)
Format                          : application/pdf
Creator                         : tbrummett
Title                           : 57983.1 SPM AR410 4 Channel Sport Receiver Manual_ML.indb
Document ID                     : uuid:18c475fb-bc54-ff40-901c-9fbd768fa2c7
Instance ID                     : uuid:62bd3349-9a36-3d4e-8423-d1a9a9dbd3ba