MGM0110VZN LTE Router User Manual Technicolor Connected Home USA LLC
Technicolor Connected Home USA LLC LTE Router
FCC ID >
FCC ID Filing: G95-MGM0110VZN
Purchase on Amazon: LTE Router
SAFETY INSTRUCTIONS AND REGULATORY NOTICES BEFORE YOU START INSTALLATION OF OR USE THIS PRODUCT, CAREFULLY READ THESE INSTRUCTIONS When using this product, always follow the basic safety precautions to reduce the risk of fire, electric shock and injury to persons, including the following: • Always install the product as described in the documentation that is included with your product. • Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. • Do not use this product to report a gas leak in the vicinity of the leak. Applicability These Safety Instructions and Regulatory Notices apply to: • Technicolor xDSL Modems & Gateways Directive Unless express and prior approval by Technicolor in writing, you may not: • Disassemble, de-compile, reverse engineer, trace or otherwise analyze the equipment, its content, operation, or functionality, or otherwise attempt to derive source code (or the underlying ideas, algorithms, structure or organization) from the equipment, or from any other information provided by Technicolor, except to the extent that this restriction is expressly prohibited by local law; • Copy, rent, loan, re-sell, sub-license, or otherwise transfer or distribute the equipment to others; • Modify, adapt or create a derivative work of the equipment; • Remove from any copies of the equipment any product identification, copyright or other notices; • Disseminate performance information or analysis (including, without limitation, benchmarks) from any source relating to the equipment. Such acts not expressly approved by Technicolor will result in the loss of product warranty and may invalidate the user's authority to operate this equipment. Technicolor disclaims all responsibility in the event of use that does not comply with the present instructions. Open Source Software notification This product may contain certain open source software modules which are subject to Open Source Software license terms. A list of the Open Source Software used by or provided under this product release and their corresponding Licenses and version number are available on Technicolor's website at the following address: www.technicolor.com/en/hi/minisites/opensoftware or at another address as Technicolor may provide from time to time. If and where applicable, depending on the terms of the applicable Open Source Software licenses, the source codes of the Open Source Software are available for free on Technicolor's website at the following address: www.technicolor.com/en/ hi/minisites/open-software. For avoidance of doubt, Open Source Software is only licensed by the original owner of the Open Source Software under the terms set forth in the designated Open Source License. Safety instructions • • • • Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. *DSL37521670* DSL37521670 TECHNICOLOR 1-5 rue Jeanne d’Arc 92130 Issy-les-Moulineaux France www.technicolor.com Copyright 2016 Technicolor. All rights reserved. All tradenames referenced are service marks, trademarks, or registered trademarks of their respective companies. Specifications subject to change without notice. DMS3-SAF-25-344 v1.0. Climatic conditions This product: • Is intended for in-house stationary use; the maximum ambient temperature must not exceed 40 °C (104 °F); the relative humidity must be between 20% and 80%. • Must not be mounted in a location exposed to direct or excessive solar and/or heat radiation. • Must not be exposed to heat trap conditions and must not be subjected to water or condensation. • Must be installed in a Pollution Degree 2 environment (environment where there is no pollution or only dry, nonconductive pollution). Ventilation and positioning • Do not block or cover any ventilation openings; never stand it on soft furnishings or carpets. • Never push objects through the openings in this product. • Leave 7 to 10 cm (3 to 4 inches) around the product to ensure that proper ventilation gets to it. • Do not install the product near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. • Do not put anything on it which might spill or drip into it (for example, lighted candles or containers of liquids). Do not expose it to dripping or splashing, rain or moisture. If a liquid enters inside the product, or if the product has been exposed to rain or moisture, unplug it immediately and contact the Customer Service. Cleaning Unplug this product from the wall socket and computer before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Water and moisture Do not use this product near water, for example near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool. Transition of the product from a cold environment to a hot one may cause condensation on some of its internal parts. Allow it to dry by itself before restarting the product. Electrical powering The powering of the product must adhere to the power specifications indicated on the marking labels. In case this product is powered by a power supply unit: • This power supply unit must be Class II and a Limited Power Source in accordance with the requirements of IEC60950-1/EN60950-1, Clause 2.5 and rated as indicated on the label on your product. It must be tested and approved to national, or local standards. • For US and Canada: This product is intended to be supplied by a UL listed Direct Plug-in Power Unit marked "Class 2" and rated as indicated on the label on your product. Only use the power supply unit that is supplied with this product. The use of other types of supplies is prohibited. If you are not sure of the type of power supply needed, consult the product's user documentation or contact your local product dealer. Accessibility The plug on the power supply cord or power supply unit serves as disconnect device. Be sure that the mains supply socket outlet you use is easily accessible and located as close to the product as possible. Overloading Do not overload mains supply socket outlets and extension power cords as this increases the risk of fire or electric shock. Telephone cable CAUTION To reduce the risk of fire, use only No 26 AWG wire size or larger telecommunication line cord. Connect the telecommunication line cord only in the PSTN, FXO, DSL or Line port of the product. Never plug the telecommunication line cord in another receptacle of the product. Follow the installation instructions in the sequence as outlined in the installation guide. Servicing To reduce the risk of electric shock, do not disassemble this product. None of its internal parts are user-replaceable; therefore, there is no reason to access the interior. Opening or removing covers may expose you to dangerous voltages. Incorrect reassembly could cause electric shock if the appliance is subsequently used. If service or repair work is required, take it to a qualified service dealer. Damage requiring service Unplug this product from the mains supply socket outlet and refer servicing to qualified service personnel under the following conditions: • When the power supply, power cord or its plug are damaged. • When the attached cords are damaged or frayed. • If liquid has been spilled into the product. • If the product has been exposed to rain or water. • If the product does not operate normally. • If the product has been dropped or damaged in any way. • There are noticeable signs of overheating. • If the product exhibits a distinct change in performance. Immediately disconnect the product if you notice it giving off a smell of burning or smoke. Under no circumstances must you open the equipment yourself; you run the risk of electrocution. Protect the product when moving it Always disconnect the power source when moving the product or connecting or disconnecting cables. Interface classifications (upon applicability) The external interfaces of the product are classified as follows: • DSL, Line: TNV circuit, subjected to overvoltages (TNV-3) • Phone, FXS: TNV circuit, not subjected to overvoltages (TNV-2) • PSTN, FXO: TNV circuit, subjected to overvoltages (TNV-3) • All other interface ports (e.g. Ethernet, USB, etc.), including the low voltage power input from the AC mains power supply: SELV circuits. WARNING • The Phone, FXS port will be classified as a TNV-3 circuit when connected internally to the PSTN, FXO port, for example, when the device is powered off. • If the product is equipped with a USB interface (slave and/or master) or any type of connector with metallic shielding, then it is not allowed to connect the Phone, FXS port with the PSTN, FXO or the DSL, Line port by any means, for example with an external telephone cable. Regulatory information You must install and use this device in strict accordance with the manufacturer's instructions as described in the user documentation that is included with your product. Before you start installation or use of this product, carefully read the contents of this document for device specific constraints or rules that may apply in the country where you want to use this product. In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or responsible representatives of the organization. If you are uncertain of the policy that applies on the use of wireless equipment in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use this device prior to turning on the equipment. Technicolor is not responsible for any radio or television interference caused by unauthorized modification of the device, or the substitution or attachment of connecting cables and equipment other than specified by Technicolor. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user. Technicolor and its authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from failing to comply with these guidelines. North-America - Canada Notification of Canadian Radio Frequency Interference Statement This Class B digital apparatus complies with Canadian ICES-003. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed 5. Canada - Industry Canada (IC) In case this product is equipped with a wireless transceiver, this device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Canada - Radiation exposure statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (8 inches) between the radiator and your body. Restricted frequency bands In case this product is equipped with a wireless transceiver operating in the 2.4 GHz band, it may only use channels 1 to 11 (2412 to 2462 MHz) on Canada territory. In case this product is equipped with a wireless transceiver operating in the 5 GHz band, it is for indoor use only. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. North-America - United States of America Federal Communications Commission (FCC) radio frequency interference statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Responsible Party: Technicolor, 101W. 103rd St., Indianapolis, IN 46290 USA, 317-587-5466. This equipment complies with Part 68 of the FCC Rules. The customer information required for Telephone Terminal Equipment ("TTE") approved for connection to the Public Switched Telephone Network ("PSTN"), pursuant to 47 CFR §68.218(b)(1) can be found at www.technicolor.com. RF exposure statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in the product documentation. When the product is equipped with a wireless interface, then it becomes a mobile or fixed mounted modular transmitter and must have a separation distance of at least 20 cm (8 inches) between the antenna and the body of the user or nearby persons. In practice, this means that the user or nearby persons must have a distance of at least 20 cm (8 inches) from the product and must not lean on the product in case it is wall-mounted. With a separation distance of 20 cm (8 inches) or more, the M(aximum) P(ermissible) E(xposure) limits are well above the potential this wireless interface is capable to produce. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Restricted frequency bands In case this product is equipped with a wireless transceiver operating in the 2.4 GHz band, it may only use channels 1 to 11 (2412 to 2462 MHz) on U.S.A. territory. In case this product is equipped with a wireless transceiver operating in the 5 GHz band, it meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Language : en XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/10/03-12:08:50 Creator Tool : FrameMaker 10.0.2 Modify Date : 2016:04:26 11:13:34+02:00 Create Date : 2016:04:26 11:10:29Z Metadata Date : 2016:04:26 11:13:34+02:00 Format : application/pdf Title : untitled Producer : Acrobat Distiller 15.0 (Windows) Document ID : uuid:ddbc5117-d9ae-4003-932a-9260e889a3f8 Instance ID : uuid:f017d4fe-d727-4a99-8488-05eca8ff1e7b Page Mode : UseOutlines Page Count : 4 Creator : FrameMaker 10.0.2EXIF Metadata provided by EXIF.tools