9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp

Askey Computer Corp Femtocell

Page 1 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 2 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 3 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 4 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 5 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 6 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 7 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 8 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 9 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 10 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 11 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 12 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 13 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 14 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 15 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 16 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 17 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 18 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 19 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 20 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 21 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 22 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 23 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 24 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 25 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 26 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 27 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 28 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 29 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 30 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 31 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 32 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 33 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 34 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 35 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 36 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 37 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 38 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 39 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 40 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 41 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 42 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 43 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 44 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 45 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 46 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 47 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 48 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 49 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 50 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 51 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 52 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 53 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 54 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 55 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 56 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 57 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 58 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 59 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 60 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 61 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 62 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 63 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 64 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 65 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 66 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 67 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 68 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 69 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 70 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 71 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 72 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 73 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 74 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 75 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 76 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Page 77 of 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp

FCC TEST REPORT
(PART 27)
REPORT NO.: RF141119C42-1
MODEL NO.: 9961 Home Cell V1
FCC ID: H8N9961V1
RECEIVED:
Nov. 19, 2014
TESTED:
Dec. 09 ~ Dec. 12, 2014
ISSUED:
Dec. 15, 2014
APPLICANT:
ADDRESS:
ASKEY COMPUTER CORP.
10F, NO.119, JIANKANG RD., ZHONGHE DIST.,
NEW TAIPEI CITY 23585, TAIWAN, R.O.C.
ISSUED BY: Bureau Veritas Consumer Products Services
(H.K.) Ltd., Taoyuan Branch
LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist.,
New Taipei City, Taiwan, R.O.C.
TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei
Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C.
This report should not be used by the client to claim
product certification, approval, or endorsement by TAF
or any government agencies.
This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted
only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this
report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product
unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you
provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided,
however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time
shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless
specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification
Report No.: RF141119C42-1
1 of 77
Report Format Version 5.0.0
TABLE OF CONTENTS
RELEASE CONTROL RECORD .............................................................................................. 3
CERTIFICATION ........................................................................................................ 4
SUMMARY OF TEST RESULTS ................................................................................ 5
2.1
MEASUREMENT UNCERTAINTY ............................................................................. 5
2.2
TEST SITE AND INSTRUMENTS .............................................................................. 6
GENERAL INFORMATION......................................................................................... 7
3.1
GENERAL DESCRIPTION OF EUT ........................................................................... 7
3.2
CONFIGURATION OF SYSTEM UNDER TEST ........................................................ 9
3.3
DESCRIPTION OF SUPPORT UNITS ....................................................................... 9
3.4
DESCRIPTION OF TEST MODES ........................................................................... 10
3.5
GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................... 11
TEST TYPES AND RESULTS .................................................................................. 12
4.1
OUTPUT POWER MEASUREMENT ....................................................................... 12
4.1.1
LIMITS OF OUTPUT POWER MEASUREMENT ..................................................... 12
4.1.2
TEST PROCEDURES .............................................................................................. 12
4.1.3
TEST SETUP ........................................................................................................... 13
4.1.4
TEST RESULTS ....................................................................................................... 14
4.2
FREQUENCY STABILITY MEASUREMENT ........................................................... 19
4.2.1
LIMITS OF FREQUENCY STABILIITY MEASUREMENT ........................................ 19
4.2.2
TEST PROCEDURE ................................................................................................ 19
4.2.3
TEST SETUP ........................................................................................................... 19
4.2.4
TEST RESULTS ....................................................................................................... 20
4.3
EMISSION BANDWIDTH MEASUREMENT ............................................................ 21
4.3.1
LIMITS OF EMISSION BANDWIDTH MEASUREMENT.......................................... 21
4.3.2
TEST SETUP ........................................................................................................... 21
4.3.3
TEST PROCEDURES .............................................................................................. 21
4.3.4
TEST RESULTS ....................................................................................................... 22
4.4
CHANNEL EDGE MEASUREMENT ........................................................................ 24
4.4.1
LIMITS OF CHANNEL EDGE MEASUREMENT ...................................................... 24
4.4.2
TEST SETUP ........................................................................................................... 24
4.4.3
TEST PROCEDURES .............................................................................................. 24
4.4.4
TEST RESULTS ....................................................................................................... 25
4.5
CONDUCTED SPURIOUS EMISSIONS .................................................................. 29
4.5.1
LIMITS OF CONDUCTED SPURIOUS EMISSIONS MEASUREMENT .................. 29
4.5.2
TEST PROCEDURE ................................................................................................ 29
4.5.3
TEST SETUP ........................................................................................................... 29
4.5.4
TEST RESULTS ....................................................................................................... 30
4.6
RADIATED EMISSION MEASUREMENT ................................................................ 54
4.6.1
LIMITS OF RADIATED EMISSION MEASUREMENT ............................................. 54
4.6.2
TEST PROCEDURES .............................................................................................. 54
4.6.3
DEVIATION FROM TEST STANDARD .................................................................... 54
4.6.4
TEST SETUP ........................................................................................................... 55
4.6.5
TEST RESULTS ....................................................................................................... 56
INFORMATION ON THE TESTING LABORATORIES ............................................. 76
APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES
TO THE EUT BY THE LAB ....................................................................................... 77
Report No.: RF141119C42-1
2 of 77
Report Format Version 5.0.0
RELEASE CONTROL RECORD
ISSUE NO.
RF141119C42-1
Report No.: RF141119C42-1
REASON FOR CHANGE
Original release
3 of 77
DATE ISSUED
Dec. 15, 2014
Report Format Version 5.0.0
1 CERTIFICATION
PRODUCT: Femtocell
MODEL NO.: 9961 Home Cell V1
BRAND: Askey
APPLICANT: ASKEY COMPUTER CORP.
TESTED: Dec. 09 ~ Dec. 12, 2014
TEST SAMPLE: ENGINEERING SAMPLE
TEST STANDARDS: FCC Part 27
FCC Part 2
The above equipment (model: 9961 Home Cell V1) has been tested by Bureau
Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found
compliance with the requirement of the above standards. The test record, data
evaluation & Equipment Under Test (EUT) configurations represented herein are true
and accurate accounts of the measurements of the sample’s EMC characteristics
under the conditions specified in this report.
PREPARED BY
, DATE:
Dec. 15, 2014
, DATE:
Dec. 15, 2014
Pettie Chen / Senior Specialist
APPROVED BY
Dylan Chiou / Project Engineer
Report No.: RF141119C42-1
4 of 77
Report Format Version 5.0.0
2 SUMMARY OF TEST RESULTS
The EUT has been tested according to the following specifications:
APPLIED STANDARD: FCC Part 27 & Part 2
STANDARD
SECTION
2.1046
27.50(d)(4)
TEST TYPE AND LIMIT
RESULT
REMARK
Equivalent Isotropically radiated
power
PASS
Meet the requirement of limit.
Frequency Stability
Stay with the authorized bands of
operation
PASS
Meet the requirement of limit.
2.1049
27.53(h)
Occupied Bandwidth
PASS
Meet the requirement of limit.
27.53(h)
Band Edge Measurements
PASS
Meet the requirement of limit.
2.1051
27.53(h)
Conducted Spurious Emissions
PASS
Meet the requirement of limit.
2.1053
27.53(h)
Radiated Spurious Emissions
PASS
Meet the requirement of limit.
Minimum passing margin is -1.0dB
at 4305.0MHz.
2.1055
27.54
2.1 MEASUREMENT UNCERTAINTY
Where relevant, the following measurement uncertainty levels have been estimated
for tests performed on the EUT as specified in CISPR 16-4-2:
MEASUREMENT
FREQUENCY
UNCERTAINTY
Conducted emissions
150kHz~30MHz
2.44 dB
30MHz ~ 200MHz
3.59 dB
200MHz ~1000MHz
3.60 dB
1GHz ~ 18GHz
2.29 dB
18GHz ~ 40GHz
2.29 dB
Radiated emissions
This uncertainty represents an expanded uncertainty expressed at approximately the
95% confidence level using a coverage factor of k=2.
Report No.: RF141119C42-1
5 of 77
Report Format Version 5.0.0
2.2 TEST SITE AND INSTRUMENTS
DESCRIPTION &
MANUFACTURER
Test Receiver
ROHDE & SCHWARZ
Spectrum Analyzer
ROHDE & SCHWARZ
BILOG Antenna
SCHWARZBECK
HORN Antenna
SCHWARZBECK
HORN Antenna
SCHWARZBECK
Preamplifier
Agilent
Preamplifier
Agilent
RF signal cable
HUBER+SUHNNER
RF signal cable
HUBER+SUHNNER
RF signal cable
HUBER+SUHNNER
Software
BV ADT
Antenna Tower
inn-co GmbH
Antenna Tower
Controller
inn-co GmbH
Turn Table
BV ADT
Turn Table Controller
BV ADT
Mini-Circuits Power
Splitter
JFW 20dB attenuation
MODEL NO.
SERIAL NO.
DATE OF
CALIBRATION
DUE DATE OF
CALIBRATION
ESCI
100424
Oct. 06, 2014
Oct. 05, 2015
FSU 43
100115
Dec. 18, 2013
Dec. 17, 2014
VULB9168
9168-155
Feb. 26, 2014
Feb. 25, 2015
BBHA 9120D
9120D-404
Jan. 05, 2014
Jan. 04, 2015
BBHA 9170
BBHA9170241
Feb. 17, 2014
Feb. 16, 2015
8449B
3008A01961
Oct. 18, 2014
Oct. 17, 2015
8447D
2944A10738
Oct. 18, 2014
Oct. 17, 2015
SUCOFLEX 104
309220/4
Aug. 09, 2014
Aug. 08, 2015
SUCOFLEX 104
250724/4
Aug. 09, 2014
Aug. 08, 2015
SUCOFLEX 104
295012/4
Aug. 09, 2014
Aug. 08, 2015
ADT_Radiated_
V7.6.15.9.4
NA
NA
NA
MA 4000
010303
NA
NA
CO2000
019303
NA
NA
TT100.
TT93021704
NA
NA
SC100.
SC93021704
NA
NA
ZN2PD-9G
NA
Apr. 25, 2014
Apr. 24, 2015
50HF-020-SMA
NA
NA
NA
NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are
traceable to NML/ROC and NIST/USA.
2. The test was performed in HwaYa Chamber 4.
3. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of
emission frequency above 1GHz if tested.
4. The FCC Site Registration No. is 460141.
5. The IC Site Registration No. is IC7450F-4.
Report No.: RF141119C42-1
6 of 77
Report Format Version 5.0.0
3 GENERAL INFORMATION
3.1 GENERAL DESCRIPTION OF EUT
EUT
Femtocell
MODEL NO.
9961 Home Cell V1
POWER SUPPLY
12Vdc (Adapter)
MODULATION TECHNOLOGY QPSK
FREQUENCY RANGE
MAX. EIRP POWER (W)
EMISSION DESIGNATOR
ANTENNA TYPE
2112.5MHz ~ 2152.5MHz
Channel Bandwidth 5MHz
Channel Bandwidth 10MHz 2115MHz ~ 2150MHz
Channel Bandwidth 15MHz 2117.5MHz ~ 2147.5MHz
Channel Bandwidth 20MHz 2120MHz ~ 2145MHz
0.570W (27.56dBm)
Channel Bandwidth 5MHz
Channel Bandwidth 10MHz 0.597W (27.76dBm)
Channel Bandwidth 15MHz 0.357W (25.53dBm)
Channel Bandwidth 20MHz 0.604W (27.81dBm)
4M43G7D
Channel Bandwidth 5MHz
Channel Bandwidth 10MHz 8M90G7D
Channel Bandwidth 15MHz 13M2G7D
Channel Bandwidth 20MHz 17M8G7D
Channel Bandwidth 5MHz:
Ch 1975: Dipole antenna with 4.59dBi gain
Ch 2175: Dipole antenna with 4.54dBi gain
Ch 2375: Dipole antenna with 4.39dBi gain
Channel Bandwidth 10MHz:
Ch 2000: Dipole antenna with 4.59dBi gain
Ch 2175: Dipole antenna with 4.54dBi gain
Ch 2350: Dipole antenna with 4.39dBi gain
Channel Bandwidth 15MHz:
Ch 2025: Dipole antenna with 4.53dBi gain
Ch 2175: Dipole antenna with 4.54dBi gain
Ch 2325: Dipole antenna with 4.44dBi gain
Channel Bandwidth 20MHz:
Ch 2050: Dipole antenna with 4.53dBi gain
Ch 2175: Dipole antenna with 4.54dBi gain
Ch 2300: Dipole antenna with 4.39dBi gain
ANTENNA CONNECTOR
I-PEX(MHF)
I/O PORTS
Refer to users’ manual
DATA CABLE
4.572m GPS antenna
(Cable Type: RG-174 Coaxial Cable (shielded))
1.8m Ethernet cable (non-shielded)
ACCESSORY DEVICES
Adapter
Report No.: RF141119C42-1
7 of 77
Report Format Version 5.0.0
NOTE:
1. The EUT uses following adapters.
Adapter 1
AOEM
Brand
ADS0248-W 120200
Model
100-240Vac~50-60Hz, 0.6A
Input Power
12Vdc, 2.0A
Output Power
1.5m cable without core attached on adapter
Power Line
Adapter 2
Brand
Model
Input Power
Output Power
Power Line
Phihong
PSAC24A-120
100-240Vac~50/60Hz, 0.6A
12Vdc, 2.0A
1.8m cable without core attached on adapter
2. The above EUT information is declared by manufacturer and for more detailed feature description,
please refer to the manufacturer's specifications or User's Manual.
Report No.: RF141119C42-1
8 of 77
Report Format Version 5.0.0
3.2 CONFIGURATION OF SYSTEM UNDER TEST
EUT
(Powered from adapter)
Test table
Notebook
*Kept in a remote area
3.3 DESCRIPTION OF SUPPORT UNITS
The EUT has been tested as an independent unit together with other necessary
accessories or support units. The following support units or accessories were used to
form a representative test configuration during the tests.
NO.
PRODUCT
BRAND
MODEL NO.
SERIAL NO.
Notebook
DELL
E5430
FKKCYW1
NO.
FCC ID
FCC DoC Approved
SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS
1 10m RJ45 UTP cable
NOTE:
1. All power cords of the above support units are non-shielded (1.8m).
Report No.: RF141119C42-1
9 of 77
Report Format Version 5.0.0
3.4 DESCRIPTION OF TEST MODES
Pre-Scan has been conducted to determine the worst-case mode from all possible
combinations between available modulations, data rates, XYZ axis and antenna ports
The worst case was found when positioned on Z-plane. Following channel(s) was
(were) selected for the final test as listed below:
Test results are presented in the report as below.
Test Mode
Test Condition
Power from adapter 1
Power from adapter 2
TEST MODE
A, B
TEST ITEM
OUTPUT POWER
FREQUENCY
STABILITY
EMISSION
BANDWIDTH
CHANNEL EDGE
CONDCUDETED
EMISSION
RADIATED
EMISSION
Below 1GHz
RADIATED
EMISSION
Above 1GHz
AVAILABLE
CHANNEL
TESTED CHANNEL
CHANNEL
BANDWIDTH
MODULATION
1975 to 2375
1975, 2175, 2375
5MHz
QPSK
2000 to 2350
2000, 2175, 2350
10MHz
QPSK
2025 to 2275
2025, 2175, 2325
15MHz
QPSK
2050 to 2300
2050, 2175, 2300
20MHz
QPSK
1975 to 2375
2175
5MHz
QPSK
2000 to 2350
2175
10MHz
QPSK
2025 to 2275
2175
15MHz
QPSK
2050 to 2300
2175
20MHz
QPSK
1975 to 2375
1975, 2175, 2375
5MHz
QPSK
2000 to 2350
2000, 2175, 2350
10MHz
QPSK
2025 to 2275
2025, 2175, 2325
15MHz
QPSK
2050 to 2300
2050, 2175, 2300
20MHz
QPSK
1975 to 2375
1975, 2375
5MHz
QPSK
2000 to 2350
2000, 2350
10MHz
QPSK
2025 to 2275
2025, 2325
15MHz
QPSK
2050 to 2300
2050, 2300
20MHz
QPSK
1975 to 2375
1975, 2175, 2375
5MHz
QPSK
2000 to 2350
2000, 2175, 2350
10MHz
QPSK
2025 to 2275
2025, 2175, 2325
15MHz
QPSK
2050 to 2300
2050, 2175, 2300
20MHz
QPSK
1975 to 2375
1975
5MHz
QPSK
2000 to 2350
2000
10MHz
QPSK
2025 to 2275
2025
15MHz
QPSK
2050 to 2300
2050
20MHz
QPSK
1975 to 2375
1975, 2175, 2375
5MHz
QPSK
2000 to 2350
2000, 2175, 2350
10MHz
QPSK
2025 to 2275
2025, 2175, 2325
15MHz
QPSK
2050 to 2300
2050, 2175, 2300
20MHz
QPSK
NOTE: For radiated emission below 1 GHz, the low, mid and high channels were pre-tested in chamber.
The low channel was the worst case and chosen for final test.
Report No.: RF141119C42-1
10 of 77
Report Format Version 5.0.0
TEST CONDITION:
TEST ITEM
ENVIRONMENTAL CONDITIONS INPUT POWER (SYSTEM)
TESTED BY
OUTPUT POWER
24deg. C, 64%RH
120Vac, 60Hz
Match Tsui
FREQUENCY STABILITY
24deg. C, 64%RH
120Vac, 60Hz
Match Tsui
EMISSION BANDWIDTH
24deg. C, 64%RH
120Vac, 60Hz
Match Tsui
CHANNEL EDGE
24deg. C, 64%RH
120Vac, 60Hz
Match Tsui
CONDCUDETED EMISSION
24deg. C, 64%RH
120Vac, 60Hz
Match Tsui
RADIATED EMISSION
25deg. C, 65%RH
120Vac, 60Hz
Chris Lin
3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS
The EUT is a RF product. According to the specifications of the manufacturer, it must
comply with the requirements of the following standards:
FCC 47 CFR Part 2
FCC 47 CFR Part 27
All test items have been performed and recorded as per the above standards.
NOTE: The EUT is also considered as a kind of computer peripheral, because the connection to
computer is necessary for typical use. It has been verified to comply with the requirements of
FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately.
Report No.: RF141119C42-1
11 of 77
Report Format Version 5.0.0
4 TEST TYPES AND RESULTS
4.1 OUTPUT POWER MEASUREMENT
4.1.1 LIMITS OF OUTPUT POWER MEASUREMENT
The radiated peak output power shall be according to the specific rule Part 27.50(d)(4)
that fixed, mobile, and portable (hand-held) stations are limited to 1 watt EIRP.
4.1.2 TEST PROCEDURES
EIRP / ERP MEASUREMENT:
a.
The power was measured with R&S Spectrum Analyzer. All measurements were
done at 3 channels (low, middle and high operational frequency range.)
b.
The conducted peak output power used the power splitter via EUT RF power
connector between simulation base station and spectrum analyzer. The path loss
included the splitter loss, cable loss and 20dB pad loss. The spectrum set RB/VB
3MHz, then read peak power value and record to the test. (All transmitted path
loss shall be considered in the test report data.)
c.
Substitution method is used for E.I.R.P measurement. In the semi-anechoic
chamber, EUT placed on the 0.8m height of Turn Table, rotated the table around
360 degrees to search the maximum radiation power and receiver antenna shall
be rotated vertical and horizontal polarization and moved height from 1m to 4m to
find the maximum polar radiated power. The “Read Value” is the spectrum reading
the maximum power value.
d.
The substitution horn antenna is substituted for EUT at the same position and
signals generator export the CW signal to the substitution antenna via a TX cable.
Rotated the Turn Table and moved receiving antenna to find the maximum
radiation power. Adjust output power level of S.G to get a Value of spectrum
reading equal to “Read Value“ of step b. Record the power level of S.G
e.
EIRP = Output power level of S.G – TX cable loss + Antenna gain of substitution
horn.
NOTE: The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is
10MHz/10MHz.
CONDUCTED POWER MEASUREMENT:
A power sensor was used on the output port of the EUT. A power meter was used to
read the response of the power sensor. Record the power level.
Report No.: RF141119C42-1
12 of 77
Report Format Version 5.0.0
4.1.3 TEST SETUP
EIRP / ERP MEASUREMENT:
For the actual test configuration, please refer to the attached file (Test Setup Photo).
CONDUCTED POWER MEASUREMENT:
COMMUNICATION
SIMULATOR
EUT
For the actual test configuration, please refer to the attached file (Test Setup Photo).
Report No.: RF141119C42-1
13 of 77
Report Format Version 5.0.0
4.1.4 TEST RESULTS
CONDUCTED OUTPUT POWER (dBm)
Band
Channel
Frequency
QPSK
1975
2112.5
23.47
LTE (BW: 5MHz)
2175
2375
2132.5
2152.5
23.44
23.67
Band
Channel
Frequency
QPSK
LTE (BW: 10MHz)
2000
2175
2350
2115.0
2132.5
2150.0
Band
Channel
Frequency
QPSK
LTE (BW: 15MHz)
2025
2175
2325
2117.5
2132.5
2147.5
Band
Channel
Frequency
QPSK
LTE (BW: 20MHz)
2050
2175
2300
2120.0
2132.5
2145.0
Report No.: RF141119C42-1
23.67
21.50
23.13
23.50
21.47
23.77
23.54
20.91
23.43
14 of 77
Report Format Version 5.0.0
EIRP (dBm)
CHANNEL BANDWIDTH: 5MHz QPSK
TX channel 1975
MODE
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2112.5
-11.76
26.82
0.74
27.56
30.00
-2.44
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2112.5
-18.14
20.72
0.74
21.46
30.00
-8.54
TX channel 2175
MODE
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2132.5
-11.83
26.75
0.73
27.48
30.00
-2.52
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2132.5
-19.26
19.73
0.73
20.46
30.00
-9.54
TX channel 2375
MODE
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2152.5
-11.75
26.83
0.73
27.56
30.00
-2.44
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2152.5
-18.93
20.17
0.73
20.90
30.00
-9.10
NOTE: EIRP (dBm) = S.G Power Value (dBm) + Correction Factor (dB).
Report No.: RF141119C42-1
15 of 77
Report Format Version 5.0.0
CHANNEL BANDWIDTH: 10MHz QPSK
TX channel 2000
MODE
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2115.0
-11.56
27.02
0.74
27.76
30.00
-2.24
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2115.0
-18.05
20.82
0.74
21.56
30.00
-8.44
TX channel 2175
MODE
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2132.5
-11.83
26.75
0.73
27.48
30.00
-2.52
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2132.5
-19.05
19.94
0.73
20.67
30.00
-9.33
TX channel 2350
MODE
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2150.0
-11.88
26.70
0.73
27.43
30.00
-2.57
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2150.0
-19.76
19.33
0.73
20.06
30.00
-9.94
NOTE: EIRP (dBm) = S.G Power Value (dBm) + Correction Factor (dB).
Report No.: RF141119C42-1
16 of 77
Report Format Version 5.0.0
CHANNEL BANDWIDTH: 15MHz QPSK
TX channel 2025
MODE
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2117.5
-13.79
24.79
0.74
25.53
30.00
-4.47
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2117.5
-19.56
19.33
0.74
20.07
30.00
-9.93
TX channel 2175
MODE
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2132.5
-13.80
24.78
0.73
25.51
30.00
-4.49
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2132.5
-20.56
18.43
0.73
19.16
30.00
-10.84
TX channel 2325
MODE
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2147.5
-14.46
24.12
0.73
24.85
30.00
-5.15
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2147.5
-20.77
18.30
0.73
19.03
30.00
-10.97
NOTE: EIRP (dBm) = S.G Power Value (dBm) + Correction Factor (dB).
Report No.: RF141119C42-1
17 of 77
Report Format Version 5.0.0
CHANNEL BANDWIDTH: 20MHz QPSK
TX channel 2050
MODE
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2120.0
-12.16
26.42
0.74
27.16
30.00
-2.84
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2120.0
-19.57
19.33
0.74
20.07
30.00
-9.93
TX channel 2175
MODE
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2132.5
-11.50
27.08
0.73
27.81
30.00
-2.19
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2132.5
-19.87
19.12
0.73
19.85
30.00
-10.15
TX channel 2300
MODE
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2145.0
-11.99
26.59
0.73
27.32
30.00
-2.68
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
2145.0
-20.27
18.79
0.73
19.52
30.00
-10.48
NOTE: EIRP (dBm) = S.G Power Value (dBm) + Correction Factor (dB).
Report No.: RF141119C42-1
18 of 77
Report Format Version 5.0.0
4.2 FREQUENCY STABILITY MEASUREMENT
4.2.1 LIMITS OF FREQUENCY STABILIITY MEASUREMENT
According to the FCC part 2.1055 shall be tested the frequency stability. The rule is
defined that” The frequency stability shall be sufficient to ensure that the fundamental
emission stays within the authorized frequency block.” The test extreme voltage is
according to the 2.1055(d)(1) Vary primary supply voltage from 85 to 115 percent of the
nominal value for other than hand carried battery equipment and the extreme
temperature rule is comply with specification of EUT -20℃ ~ 50℃.
4.2.2 TEST PROCEDURE
a. Power must be removed when changing from one temperature to another or one
voltage to another voltage. Power warm up is at least 15 min and power applied
should perform before recording frequency error.
b. EUT is connected the external power supply to control the AC input power. The
various Volts from the minimum 108Volts to 132Volts. Each step shall be record
the frequency error rate.
c. The temperature range step is 10 degrees in this test items. All temperature levels
shall be hold the ±0.5℃ during the measurement testing.
d. The each temperature step shall be at least 0.5 hours, consider the EUT could be
test under the stability condition.
4.2.3 TEST SETUP
OVEN ROOM
COMMUNICATION
SIMULATOR
ANTENNA
EXTERNAL POWER SOURCE
EUT
AC POWER SUPPLY
Report No.: RF141119C42-1
19 of 77
Report Format Version 5.0.0
4.2.4 TEST RESULTS
FREQUENCY ERROR (ppm)
VOLTAGE (Volts)
LIMIT (ppm)
5MHz
10MHz
15MHz
20MHz
132
-0.007
-0.007
-0.007
-0.008
2.5
120
-0.008
-0.008
-0.007
-0.008
2.5
108
-0.007
-0.007
-0.006
-0.008
2.5
NOTE: The applicant defined the normal working voltage of the adapter is from 108Vac to 132Vac.
FREQUENCY ERROR (ppm)
TEMP. (℃)
LIMIT (ppm)
5MHz
10MHz
15MHz
20MHz
50
-0.011
-0.010
-0.011
-0.009
2.5
40
-0.009
-0.009
-0.008
-0.011
2.5
30
-0.007
-0.008
-0.009
-0.008
2.5
20
-0.008
-0.008
-0.007
-0.008
2.5
10
-0.010
-0.009
-0.009
-0.010
2.5
-0.011
-0.010
-0.009
-0.013
2.5
-10
-0.014
-0.013
-0.011
-0.012
2.5
-20
-0.012
-0.014
-0.015
-0.015
2.5
Report No.: RF141119C42-1
20 of 77
Report Format Version 5.0.0
4.3 EMISSION BANDWIDTH MEASUREMENT
4.3.1 LIMITS OF EMISSION BANDWIDTH MEASUREMENT
According to FCC 27.53(h) specified that emission bandwidth is defined as the width of
the signal between two points, one below the carrier center frequency and one above
the carrier center frequency, outside of which all emissions are attenuated at least
26dB below the transmitter power.
4.3.2 TEST SETUP
SPECTURM
ANALYZER
EUT
20dB pad
SIGNAL
GENERATOR
4.3.3 TEST PROCEDURES
The transmitter output was connected to the spectrum analyzer through an attenuator.
The bandwidth of the fundamental frequency was measured by spectrum analyzer with
RBW = 100kHz and VBW = 300kHz (Channel Bandwidth: 5MHz) RBW = 200kHz and
VBW = 620kHz (Channel Bandwidth: 10MHz and 15MHz), RBW = 430kHz and VBW =
1.2MHz (Channel Bandwidth: 20MHz). The 26dB bandwidth is defined as the total
spectrum the power of which is higher than peak power minus 26dB.
Report No.: RF141119C42-1
21 of 77
Report Format Version 5.0.0
4.3.4 TEST RESULTS
CHANNEL BANDWIDTH: 5MHz / QPSK
CHANNEL
FREQUENCY
(MHz)
1975
-26dBc BANDWIDTH (MHz)
OCCUPIED BANDWIDTH (MHz)
CHAIN 0
CHAIN 1
CHAIN 0
CHAIN 1
2112.5
4.94
4.92
4.43
4.42
2175
2132.5
4.88
4.93
4.42
4.43
2375
2152.5
4.99
4.92
4.43
4.42
SPECTRUM PLOT OF WORST VALUE
-26dBc Bandwidth
Occupied Bandwidth
CHANNEL BANDWIDTH: 10MHz / QPSK
CHANNEL
FREQUENCY
(MHz)
2000
-26dBc BANDWIDTH (MHz)
OCCUPIED BANDWIDTH (MHz)
CHAIN 0
CHAIN 1
CHAIN 0
CHAIN 1
2115
9.63
9.61
8.90
8.90
2175
2132.5
9.73
9.67
8.90
8.90
2350
2150
9.61
9.62
8.90
8.90
SPECTRUM PLOT OF WORST VALUE
-26dBc Bandwidth
Occupied Bandwidth
Report No.: RF141119C42-1
22 of 77
Report Format Version 5.0.0
CHANNEL BANDWIDTH: 15MHz / QPSK
CHANNEL
FREQUENCY
(MHz)
2025
-26dBc BANDWIDTH (MHz)
OCCUPIED BANDWIDTH (MHz)
CHAIN 0
CHAIN 1
CHAIN 0
CHAIN 1
2117.5
14.07
14.05
13.20
13.20
2175
2132.5
14.15
14.02
13.27
13.27
2325
2147.5
14.01
14.05
13.20
13.23
SPECTRUM PLOT OF WORST VALUE
-26dBc Bandwidth
Occupied Bandwidth
CHANNEL BANDWIDTH: 20MHz / QPSK
CHANNEL
FREQUENCY
(MHz)
2050
-26dBc BANDWIDTH (MHz)
OCCUPIED BANDWIDTH (MHz)
CHAIN 0
CHAIN 1
CHAIN 0
CHAIN 1
2120
19.28
19.17
17.87
17.80
2175
2132.5
19.19
18.95
17.87
17.80
2300
2145
19.12
19.10
17.80
17.80
SPECTRUM PLOT OF WORST VALUE
-26dBc Bandwidth
Occupied Bandwidth
Report No.: RF141119C42-1
23 of 77
Report Format Version 5.0.0
4.4 CHANNEL EDGE MEASUREMENT
4.4.1 LIMITS OF CHANNEL EDGE MEASUREMENT
According to FCC 27.53(h) specified the power of any emission outside a licensee's
frequency block shall be attenuated below the transmitter power (P) in watts by at least
43 + 10 log10 (P) dB. In the 1 MHz bands immediately outside and adjacent to the
frequency block a resolution bandwidth of at least one percent of the emission
bandwidth of the fundamental emission of the transmitter may be employed.
4.4.2 TEST SETUP
SPECTURM
ANALYZER
EUT
20dB pad
SIGNAL
GENERATOR
4.4.3 TEST PROCEDURES
a.
The EUT was set up for the rated peak power. The power was measured with
Spectrum Analyzer. All measurements were done at 3 channels: low, middle and
high operational frequency range.
b.
The center frequency of spectrum is the band edge frequency and span is 10MHz.
RBW of the spectrum is 51kHz (Channel Bandwidth: 5MHz) / 100kHz (Channel
Bandwidth: 10MHz) / 150kHz (Channel Bandwidth: 15MHz) / 200kHz (Channel
Bandwidth: 20MHz).
c.
Record the max trace plot into the test report.
Report No.: RF141119C42-1
24 of 77
Report Format Version 5.0.0
4.4.4 TEST RESULTS
Channel Bandwidth: 5MHz
CHAIN 0
CHANNEL
1975
QPSK
CHANNEL
2375
QPSK
CHAIN 1
CHANNEL
QPSK
CHANNEL
2375
QPSK
1975
Report No.: RF141119C42-1
25 of 77
Report Format Version 5.0.0
Channel Bandwidth: 10MHz
CHAIN 0
CHANNEL
2000
QPSK
CHANNEL
2350
QPSK
CHAIN 1
CHANNEL
QPSK
CHANNEL
2350
QPSK
2000
Report No.: RF141119C42-1
26 of 77
Report Format Version 5.0.0
Channel Bandwidth: 15MHz
CHAIN 0
CHANNEL
2025
QPSK
CHANNEL
2325
QPSK
CHAIN 1
CHANNEL
QPSK
CHANNEL
2325
QPSK
2025
Report No.: RF141119C42-1
27 of 77
Report Format Version 5.0.0
Channel Bandwidth: 20MHz
CHAIN 0
CHANNEL
2050
QPSK
CHANNEL
2300
QPSK
CHAIN 1
CHANNEL
QPSK
CHANNEL
2300
QPSK
2050
Report No.: RF141119C42-1
28 of 77
Report Format Version 5.0.0
4.5 CONDUCTED SPURIOUS EMISSIONS
4.5.1 LIMITS OF CONDUCTED SPURIOUS EMISSIONS MEASUREMENT
In the FCC 27.53(h), On any frequency outside a licensee’s frequency block,
The power of any emission shall be attenuated below the transmitter power (P) by at
least 43 + 10 log (P) dB, the emission limit equal to –13dBm.
4.5.2 TEST PROCEDURE
a. All measurements were done at 3 channels: low, middle and high operational
frequency range.
b. When the spectrum scanned from 9kHz to 20GHz, it shall be connected to the
20dB pad attenuated the carried frequency. The spectrum set RB = 1MHz, VB =
3MHz.
4.5.3 TEST SETUP
SPECTURM
ANALYZER
EUT
20dB pad
SIGNAL
GENERATOR
Report No.: RF141119C42-1
29 of 77
Report Format Version 5.0.0
4.5.4 TEST RESULTS
Channel Bandwidth: 5MHz / CHAIN 0
CHANNEL 1975
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
30 of 77
Report Format Version 5.0.0
Channel Bandwidth: 5MHz / CHAIN 0
CHANNEL 2175
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
31 of 77
Report Format Version 5.0.0
Channel Bandwidth: 5MHz / CHAIN 0
CHANNEL 2375
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
32 of 77
Report Format Version 5.0.0
Channel Bandwidth: 5MHz / CHAIN 1
CHANNEL 1975
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
33 of 77
Report Format Version 5.0.0
Channel Bandwidth: 5MHz / CHAIN 1
CHANNEL 2175
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
34 of 77
Report Format Version 5.0.0
Channel Bandwidth: 5MHz / CHAIN 1
CHANNEL 2375
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
35 of 77
Report Format Version 5.0.0
Channel Bandwidth: 10MHz / CHAIN 0
CHANNEL 2000
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
36 of 77
Report Format Version 5.0.0
Channel Bandwidth: 10MHz / CHAIN 0
CHANNEL 2175
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
37 of 77
Report Format Version 5.0.0
Channel Bandwidth: 10MHz / CHAIN 0
CHANNEL 2350
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
38 of 77
Report Format Version 5.0.0
Channel Bandwidth: 10MHz / CHAIN 1
CHANNEL 2000
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
39 of 77
Report Format Version 5.0.0
Channel Bandwidth: 10MHz / CHAIN 1
CHANNEL 2175
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
40 of 77
Report Format Version 5.0.0
Channel Bandwidth: 10MHz / CHAIN 1
CHANNEL 2350
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
41 of 77
Report Format Version 5.0.0
Channel Bandwidth: 15MHz / CHAIN 0
CHANNEL 2025
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
42 of 77
Report Format Version 5.0.0
Channel Bandwidth: 15MHz / CHAIN 0
CHANNEL 2175
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
43 of 77
Report Format Version 5.0.0
Channel Bandwidth: 15MHz / CHAIN 0
CHANNEL 2325
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
44 of 77
Report Format Version 5.0.0
Channel Bandwidth: 15MHz / CHAIN 1
CHANNEL 2025
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
45 of 77
Report Format Version 5.0.0
Channel Bandwidth: 15MHz / CHAIN 1
CHANNEL 2175
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
46 of 77
Report Format Version 5.0.0
Channel Bandwidth: 15MHz / CHAIN 1
CHANNEL 2325
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
47 of 77
Report Format Version 5.0.0
Channel Bandwidth: 20MHz / CHAIN 0
CHANNEL 2050
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
48 of 77
Report Format Version 5.0.0
Channel Bandwidth: 20MHz / CHAIN 0
CHANNEL 2175
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
49 of 77
Report Format Version 5.0.0
Channel Bandwidth: 20MHz / CHAIN 0
CHANNEL 2300
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
50 of 77
Report Format Version 5.0.0
Channel Bandwidth: 20MHz / CHAIN 1
CHANNEL 2050
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
51 of 77
Report Format Version 5.0.0
Channel Bandwidth: 20MHz / CHAIN 1
CHANNEL 2175
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
52 of 77
Report Format Version 5.0.0
Channel Bandwidth: 20MHz / CHAIN 1
CHANNEL 2300
FREQUENCY RANGE : 9kHz~3GHz
FREQUENCY RANGE : 3GHz~10GHz
FREQUENCY RANGE : 10GHz~20GHz
Report No.: RF141119C42-1
53 of 77
Report Format Version 5.0.0
4.6 RADIATED EMISSION MEASUREMENT
4.6.1 LIMITS OF RADIATED EMISSION MEASUREMENT
In the FCC 27.53(h), On any frequency outside a licensee’s frequency block,
The power of any emission shall be attenuated below the transmitter power (P) by at
least 43 + 10 log (P) dB, the emission limit equal to –13dBm.
4.6.2 TEST PROCEDURES
a.
The power was measured with R&S Spectrum Analyzer. All measurements were
done at 3 channels (low, middle and high channel of operational frequency range.)
b.
Substitution method is used for E.I.R.P measurement. In the semi-anechoic
chamber, EUT placed on the 0.8m height of Turn Table, rotated the table around
360 degrees to search the maximum radiation power and receiver antenna shall
be rotated vertical and horizontal polarization and moved height from 1m to 4m to
find the maximum polar radiated power. The “Read Value” is the spectrum reading
the maximum power value.
c.
The substitution antenna is substituted for EUT at the same position and signals
generator export the CW signal to the substitution antenna via a TX cable.
Rotated the Turn Table and moved receiving antenna to find the maximum
radiation power. Adjust output power level of S.G to get a Value of spectrum
reading equal to “Read Value” of step b. Record the power level of S.G
d.
EIRP = Output power level of S.G – TX cable loss + Antenna gain of substitution
antenna.
NOTE: The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is
1MHz/3MHz
4.6.3 DEVIATION FROM TEST STANDARD
No deviation
Report No.: RF141119C42-1
54 of 77
Report Format Version 5.0.0
4.6.4 TEST SETUP
For the actual test configuration, please refer to the attached file (Test Setup Photo).
Report No.: RF141119C42-1
55 of 77
Report Format Version 5.0.0
4.6.5 TEST RESULTS
BELOW 1GHz
CHANNEL BANDWIDTH: 5MHz
MODE
TX channel 1975
FREQUENCY RANGE
Below 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TEST MODE
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
111.50
-44.89
-51.06
0.42
-50.64
-13.00
-37.64
181.30
-51.84
-60.13
3.08
-57.05
-13.00
-44.05
286.10
-51.35
-60.44
5.20
-55.24
-13.00
-42.24
402.50
-61.98
-66.71
5.28
-61.43
-13.00
-48.43
658.60
-66.07
-67.65
4.91
-62.74
-13.00
-49.74
937.90
-62.20
-57.27
3.92
-53.35
-13.00
-40.35
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
57.20
-38.11
-35.60
-8.21
-43.81
-13.00
-30.81
107.60
-39.52
-44.07
0.58
-43.49
-13.00
-30.49
177.40
-48.35
-50.50
2.59
-47.91
-13.00
-34.91
286.10
-57.42
-63.60
5.20
-58.40
-13.00
-45.40
782.70
-64.65
-59.77
4.25
-55.52
-13.00
-42.52
937.90
-62.65
-54.59
3.92
-50.67
-13.00
-37.67
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
56 of 77
Report Format Version 5.0.0
MODE
TX channel 1975
FREQUENCY RANGE
Below 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TEST MODE
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
30.00
-56.82
-40.85
-12.18
-53.03
-13.00
-40.03
127.00
-45.94
-52.07
-0.06
-52.13
-13.00
-39.13
237.60
-51.67
-62.50
5.42
-57.08
-13.00
-44.08
381.10
-58.83
-64.18
5.25
-58.93
-13.00
-45.93
742.00
-61.10
-60.15
4.74
-55.41
-13.00
-42.41
939.90
-61.09
-56.12
3.93
-52.19
-13.00
-39.19
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
35.80
-37.79
-32.37
-11.43
-43.80
-13.00
-30.80
127.00
-51.12
-54.18
-0.06
-54.24
-13.00
-41.24
233.70
-58.36
-65.50
5.42
-60.08
-13.00
-47.08
365.60
-58.90
-63.73
5.22
-58.51
-13.00
-45.51
784.70
-63.06
-58.16
4.23
-53.93
-13.00
-40.93
937.90
-58.04
-49.98
3.92
-46.06
-13.00
-33.06
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
57 of 77
Report Format Version 5.0.0
CHANNEL BANDWIDTH: 10MHz
MODE
TX channel 2000
FREQUENCY RANGE
Below 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TEST MODE
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
113.40
-45.84
-52.02
0.34
-51.68
-13.00
-38.68
286.10
-51.04
-60.13
5.20
-54.93
-13.00
-41.93
431.60
-62.17
-66.71
5.15
-61.56
-13.00
-48.56
662.40
-66.62
-68.17
4.95
-63.22
-13.00
-50.22
802.10
-64.01
-61.75
4.02
-57.73
-13.00
-44.73
937.90
-61.84
-56.91
3.92
-52.99
-13.00
-39.99
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
57.20
-37.33
-34.82
-8.21
-43.03
-13.00
-30.03
107.60
-37.20
-41.75
0.58
-41.17
-13.00
-28.17
177.40
-48.67
-50.82
2.59
-48.23
-13.00
-35.23
286.10
-56.86
-63.04
5.20
-57.84
-13.00
-44.84
429.60
-61.69
-64.45
5.15
-59.30
-13.00
-46.30
860.30
-64.11
-57.71
3.95
-53.76
-13.00
-40.76
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
58 of 77
Report Format Version 5.0.0
MODE
TX channel 2000
FREQUENCY RANGE
Below 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TEST MODE
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
47.50
-59.83
-47.53
-10.16
-57.69
-13.00
-44.69
127.00
-46.19
-52.32
-0.06
-52.38
-13.00
-39.38
239.50
-52.13
-62.79
5.41
-57.38
-13.00
-44.38
381.10
-58.94
-64.29
5.25
-59.04
-13.00
-46.04
726.50
-60.89
-60.72
4.91
-55.81
-13.00
-42.81
937.90
-59.90
-54.97
3.92
-51.05
-13.00
-38.05
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
30.00
-38.27
-34.15
-12.18
-46.33
-13.00
-33.33
127.00
-51.09
-54.15
-0.06
-54.21
-13.00
-41.21
348.20
-58.70
-64.09
5.20
-58.89
-13.00
-45.89
557.70
-62.15
-62.91
4.62
-58.29
-13.00
-45.29
784.70
-65.43
-60.53
4.23
-56.30
-13.00
-43.30
937.90
-60.88
-52.82
3.92
-48.90
-13.00
-35.90
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
59 of 77
Report Format Version 5.0.0
CHANNEL BANDWIDTH: 15MHz
MODE
TX channel 2025
FREQUENCY RANGE
Below 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TEST MODE
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
33.90
-58.14
-42.59
-11.68
-54.27
-13.00
-41.27
127.00
-45.67
-51.80
-0.06
-51.86
-13.00
-38.86
241.50
-52.56
-63.08
5.41
-57.67
-13.00
-44.67
383.10
-58.74
-63.98
5.25
-58.73
-13.00
-45.73
745.90
-61.27
-60.11
4.68
-55.43
-13.00
-42.43
937.90
-56.07
-51.14
3.92
-47.22
-13.00
-34.22
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
53.30
-39.00
-35.32
-9.05
-44.37
-13.00
-31.37
127.00
-50.96
-54.02
-0.06
-54.08
-13.00
-41.08
237.60
-57.64
-64.89
5.42
-59.47
-13.00
-46.47
511.10
-59.41
-61.31
4.84
-56.47
-13.00
-43.47
786.60
-64.28
-59.33
4.19
-55.14
-13.00
-42.14
937.90
-57.29
-49.23
3.92
-45.31
-13.00
-32.31
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
60 of 77
Report Format Version 5.0.0
MODE
TX channel 2025
FREQUENCY RANGE
Below 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TEST MODE
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
51.30
-55.05
-44.59
-9.46
-54.05
-13.00
-41.05
127.00
-45.53
-51.66
-0.06
-51.72
-13.00
-38.72
239.50
-52.68
-63.34
5.41
-57.93
-13.00
-44.93
383.10
-58.86
-64.10
5.25
-58.85
-13.00
-45.85
747.80
-61.20
-59.94
4.65
-55.29
-13.00
-42.29
937.90
-54.34
-49.41
3.92
-45.49
-13.00
-32.49
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
31.90
-35.90
-31.35
-11.93
-43.28
-13.00
-30.28
125.10
-51.13
-54.32
-0.03
-54.35
-13.00
-41.35
237.60
-57.92
-65.17
5.42
-59.75
-13.00
-46.75
425.80
-62.27
-65.16
5.17
-59.99
-13.00
-46.99
802.10
-65.85
-60.67
4.02
-56.65
-13.00
-43.65
937.90
-59.57
-51.51
3.92
-47.59
-13.00
-34.59
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
61 of 77
Report Format Version 5.0.0
CHANNEL BANDWIDTH: 20MHz
MODE
TX channel 2050
FREQUENCY RANGE
Below 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TEST MODE
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
111.50
-45.28
-51.45
0.42
-51.03
-13.00
-38.03
286.10
-51.41
-60.50
5.20
-55.30
-13.00
-42.30
392.80
-62.67
-67.44
5.25
-62.19
-13.00
-49.19
660.50
-66.34
-67.91
4.93
-62.98
-13.00
-49.98
784.70
-64.47
-62.54
4.23
-58.31
-13.00
-45.31
937.90
-58.96
-54.03
3.92
-50.11
-13.00
-37.11
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
55.20
-33.57
-30.47
-8.63
-39.10
-13.00
-26.10
109.50
-37.10
-41.58
0.50
-41.08
-13.00
-28.08
175.50
-48.97
-50.49
2.34
-48.15
-13.00
-35.15
447.10
-61.99
-64.12
5.10
-59.02
-13.00
-46.02
662.40
-66.78
-64.80
4.95
-59.85
-13.00
-46.85
937.90
-59.13
-51.07
3.92
-47.15
-13.00
-34.15
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
62 of 77
Report Format Version 5.0.0
MODE
TX channel 2050
FREQUENCY RANGE
Below 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TEST MODE
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
37.80
-56.77
-41.64
-11.18
-52.82
-13.00
-39.82
127.00
-46.19
-52.32
-0.06
-52.38
-13.00
-39.38
241.50
-53.15
-63.67
5.41
-58.26
-13.00
-45.26
381.10
-58.88
-64.23
5.25
-58.98
-13.00
-45.98
742.00
-60.73
-59.78
4.74
-55.04
-13.00
-42.04
937.90
-60.82
-55.89
3.92
-51.97
-13.00
-38.97
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
35.80
-38.11
-32.69
-11.43
-44.12
-13.00
-31.12
125.10
-50.98
-54.17
-0.03
-54.20
-13.00
-41.20
237.60
-58.09
-65.34
5.42
-59.92
-13.00
-46.92
569.30
-63.06
-63.41
4.56
-58.85
-13.00
-45.85
784.70
-63.08
-58.18
4.23
-53.95
-13.00
-40.95
955.40
-60.98
-52.59
3.91
-48.68
-13.00
-35.68
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
63 of 77
Report Format Version 5.0.0
ABOVE 1GHz
CHANNEL BANDWIDTH: 5MHz
MODE
Channel 1975
FREQUENCY
RANGE
Above 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4225.0
-29.11
-21.32
6.87
-14.45
-13.00
-1.45
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4225.0
-35.12
-27.97
6.87
-21.10
-13.00
-8.10
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
64 of 77
Report Format Version 5.0.0
MODE
Channel 2175
FREQUENCY
RANGE
Above 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4265.0
-32.66
-24.63
6.84
-17.79
-13.00
-4.79
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4265.0
-36.11
-28.81
6.84
-21.97
-13.00
-8.97
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
65 of 77
Report Format Version 5.0.0
MODE
Channel 2375
FREQUENCY
RANGE
Above 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4305.0
-29.08
-20.83
6.83
-14.00
-13.00
-1.00
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4305.0
-33.80
-26.36
6.83
-19.53
-13.00
-6.53
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
66 of 77
Report Format Version 5.0.0
CHANNEL BANDWIDTH: 10MHz
MODE
Channel 2000
FREQUENCY
RANGE
Above 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4230.0
-33.52
-25.70
6.87
-18.83
-13.00
-5.83
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4230.0
-40.71
-33.55
6.87
-26.68
-13.00
-13.68
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
67 of 77
Report Format Version 5.0.0
MODE
Channel 2175
FREQUENCY
RANGE
Above 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4265.0
-39.06
-31.03
6.84
-24.19
-13.00
-11.19
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4265.0
-41.37
-34.07
6.84
-27.23
-13.00
-14.23
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
68 of 77
Report Format Version 5.0.0
MODE
Channel 2350
FREQUENCY
RANGE
Above 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4300.0
-33.75
-25.53
6.83
-18.70
-13.00
-5.70
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4300.0
-41.83
-34.41
6.83
-27.58
-13.00
-14.58
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
69 of 77
Report Format Version 5.0.0
CHANNEL BANDWIDTH: 15MHz
MODE
Channel 2025
FREQUENCY
RANGE
Above 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4235.0
-42.06
-34.22
6.87
-27.35
-13.00
-14.35
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4235.0
-46.76
-39.58
6.87
-32.71
-13.00
-19.71
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
70 of 77
Report Format Version 5.0.0
MODE
Channel 2175
FREQUENCY
RANGE
Above 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4265.0
-40.27
-32.24
6.84
-25.40
-13.00
-12.40
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4265.0
-49.01
-41.71
6.84
-34.87
-13.00
-21.87
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
71 of 77
Report Format Version 5.0.0
MODE
Channel 2325
FREQUENCY
RANGE
Above 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4295.0
-45.09
-36.89
6.83
-30.06
-13.00
-17.06
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4295.0
-53.03
-45.62
6.83
-38.79
-13.00
-25.79
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
72 of 77
Report Format Version 5.0.0
CHANNEL BANDWIDTH: 20MHz
MODE
Channel 2050
FREQUENCY
RANGE
Above 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4240.0
-33.95
-26.07
6.86
-19.21
-13.00
-6.21
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4240.0
-44.36
-37.16
6.86
-30.30
-13.00
-17.30
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
73 of 77
Report Format Version 5.0.0
MODE
Channel 2175
FREQUENCY
RANGE
Above 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4265.0
-35.16
-27.13
6.84
-20.29
-13.00
-7.29
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4265.0
-39.98
-32.68
6.84
-25.84
-13.00
-12.84
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
74 of 77
Report Format Version 5.0.0
MODE
Channel 2300
FREQUENCY
RANGE
Above 1000MHz
ENVIRONMENTAL
CONDITIONS
25deg. C, 65%RH
INPUT POWER
120Vac, 60 Hz
TESTED BY
Chris Lin
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4290.0
-34.19
-26.03
6.84
-19.19
-13.00
-6.19
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
No.
Freq. (MHz)
Reading
(dBm)
S.G Power
Value (dBm)
Correction
Factor (dB)
EIRP (dBm)
Limit (dBm)
Margin (dB)
4290.0
-39.32
-31.94
6.84
-25.10
-13.00
-12.10
REMARKS:
1. EIRP(dBm) = S.G Power Value (dBm) + Correction Factor (dB).
2. Correction Factor = gain of substitution antenna + cable loss
Report No.: RF141119C42-1
75 of 77
Report Format Version 5.0.0
5
INFORMATION ON THE TESTING LABORATORIES
We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were
founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety
consultation. Our laboratories are accredited and approved according to ISO/IEC
17025.
If you have any comments, please feel free to contact us at the following:
Linko EMC/RF Lab:
Tel: 886-2-26052180
Fax: 886-2-26051924
Hsin Chu EMC/RF/Telecom Lab:
Tel: 886-3-5935343
Fax: 886-3-5935342
Hwa Ya EMC/RF/Safety Lab:
Tel: 886-3-3183232
Fax: 886-3-3270892
Email: service.adt@tw.bureauveritas.com
Web Site: www.bureauveritas-adt.com
The address and road map of all our labs can be found in our web site also.
Report No.: RF141119C42-1
76 of 77
Report Format Version 5.0.0
6 APPENDIX A – MODIFICATIONS RECORDERS FOR
ENGINEERING CHANGES TO THE EUT BY THE LAB
No modifications were made to the EUT by the lab during the test.
---END---
Report No.: RF141119C42-1
77 of 77
Report Format Version 5.0.0
Download: 9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Mirror Download [FCC.gov]9961V1 Femtocell Test Report (PCB-Part 27)_rev Askey Computer Corp
Document ID2489188
Application IDPY8yEbHykbRoPRTPlbCc0A==
Document DescriptionTest Report (PCB-Part 27)_rev.pdf
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize158.85kB (1985665 bits)
Date Submitted2014-12-31 00:00:00
Date Available2014-12-31 00:00:00
Creation Date2018-02-09 20:21:34
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2018-02-09 20:21:34
Document TitleTest Report (PCB-Part 27)_rev
Document CreatorPScript5.dll Version 5.2.2
Document Author: pettchen

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Annotate, Fill forms, Extract, Print high-res
Author                          : pettchen
Create Date                     : 2014:12:27 17:54:14+08:00
Modify Date                     : 2014:12:27 17:54:29+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : pettchen
Title                           : Microsoft Word - RF141119C42-1_Askey_9961 Home Cell V1 _Femtocell__LTE Band 4_Part 27M
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2014:12:27 17:54:29+08:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:281a4d0b-b1ed-4e4f-82e1-8b061d98f288
Instance ID                     : uuid:8ca23318-4e15-46c3-81f0-12a669aff6b3
Page Count                      : 77