FS2-D Face Station2 Test Report DXX rev01 Suprema Inc.

Suprema Inc. Face Station2

Test Report for FCC
Company name
Address
Telephone
Product name
Model No.
Serial No.
Test date
Testing
location
Standard
Tested by
Reviewed by
Abbreviation
* Note
- This test report is not permitted to copy partly without our permission
- This test result is dependent on only equipment to be used
- This test result based on a single evaluation of one sample of the above mentioned
Date of issue 17-Mar-179-Feb-17
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 1 of 18
347-69, Jungbu-daero 147beon-gil, Majang-myeon, Icheon-si,
Gyeonggi-do 467-811, R. O. Korea
FCC PART 15 Subpart C(15.225), ANSI C 63.10(2013)
OK, Pass = Complied, Fail = Failed, N/A = not applicable
Measurement facility registration number
Senior Engineer H.K. Lee
Engineering Manager I.k. Hong (Signature)
659627
(Signature)
16F Parkview office Tower, Jeongja-dong Bundang-gu, Seongnam,
Gyeonggi
Product Manufacturer
Country of origin
Face Station2
None
FS2-D
Suprema Inc
KOREA
Contact person
FCC ID :TKWFS2-D
+82-31-710-4908
Bongseop Song
Result Complied
Applicant
Report Number ESTRFC1703-003
Suprema Inc
3
4
5
6
8
8
8
8
10
10
10
11
13
13
13
13
14
15
16
17
17
17
18
6.2 Test E
q
ui
p
ments ……………………………………………………………………………
6. Fre
q
uenc
y
Tolerance …………………………………………………………………………
7.3 Environmental conditions …………………………………………………………………
7. Measurement of radiated emission …………………………………………………………
7.2 Measurement e
q
ui
p
ment …………………………………………………………………
7.1 Radiated emission limits, general re
q
uirements ………………………………………
6.3 Measurement Data …………………………………………………………………………
6.1 Procedure ……………………………………………………………………………………
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 2 of 18
7.4 Test data(9 kHz ~30 MHz) ………………………………………………………………
8.1 Measurement e
q
ui
p
ment …………………………………………………………………
7.6 Test data(Above 1 GHz) …………………………………………………………………
8. Measurement of conducted emission ………………………………………………………
Appendix 2. Antenna Requirement
Appendix 1. Special diagram(Adapter Mode)
8.3 Test data ……………………………………………………………………………………
8.2 Environmental conditions …………………………………………………………………
7.5 Test data(30 MHz ~ 1 GHz) ………………………………………………………………
Contents
1. Laborator
y
Information …………………………………………………………………………
2. Descri
p
tion of EUT ……………………………………………………………………………
3. Test Standards …………………………………………………………………………………
5.3 Measurement Data ……………………………………………………………………………
4. Measurement condition ………………………………………………………………………
5. 20dBm Bandwidth ………………………………………………………………………………
5.1 Procedure ……………………………………………………………………………………
5.2 20dBm Bandwidth Set u
p
…………………………………………………………………
1. Laboratory Information
1.1 General
1.2 Test Lab.
Corporation Name : ESTECH Co., Ltd.
Head Office : Suite 1015 World Meridian II, 123 Gasan Digital 2-ro, Geumcheon-gu,
Seoul 153-759, R. O. Korea
EMC/Telecom/Safety Test Lab : 347-69, Jungbu-daero 147beon-gil, Majang-myeon, Icheon-si,
Gyeonggi-do 467-811, R. O. Korea
1.3 Official Qualification(s)
MSIP : Granted Accreditation from Ministry of Information & Communication for EMC, Safety
and Telecommunication
KOLAS : Accredited Lab By Korea Laboratory Accreditation Schema base on CENELEC
requirements
FCC : Conformity Assessment Body(CAB) with registration number 659627 under
VCCI : Granted Accreditation from Voluntary Control Council for Interference from ITE
This EUT (Equipment Under Test) has been shown to be capable of compliance with the applicable
technical standards and is tested in accordance with the measurement procedures as indicated in
this report.ESTECH Lab attests to accuracy of test data. All measurement reported herein were
performed by ESTECH Co., Ltd.
ESTECH Lab assume full responsibility for the completeness of these measurements and vouch for
the qualifications of all persons taking them.
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 3 of 18
APEC TEL MRA between the RRA and the FCC
2. Description of EUT
2.1 Summary of Equipment Under Test
Product :
Model Number : FS2-D
Serial Number :
Manufacturer :
Country of origin :
Operating Frequency : 13.56 MHz
Antenna Type : PCB Patten Antenna
Modulation Type : ASK
Channel : 1 ch
Power Rating :
Receipt Date :
X-tal list(s) or
Frequencies generated
:
2.2 General descriptions of EUT
Face Station2
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 4 of 18
CPU 1.4 GHz Quad Core
Memory 8GB Flash + 1GB RAM
LCD 4” color TFT LCD (Resolution: 480 x 800)
Sound 24 bit/Voice DSP (echo cancel)
Operating temperature -20 °C ~ 50 °C
Storage temperature -40 °C ~ 70 °C
Operating humidity 0 % ~ 80 %, non-condensing
Storage humidity 0 % ~ 90 %, non-condensing
Camera CMOS VGA (720 x 480) pixels
Camera angle Visual : Diagonal 92.7° , IR : Diagonal 58°
Dimension (W x H x D) 141 mm x 125 mm x 164 mm (h)
Weight Device: 610 g (With Wall-Bracket)
RF Option RFID : 13.56 MHz / 117 kHz
The highest operating frequency is CPU 1.4 GHz
5-Dec-16
INPUT : (100 - 240) Va.c., (50 - 60) Hz, 1.0 A
OUTPUT : 12 Vd.c., 2.5 A
KOREA
Suprema Inc
NONE
3. Test Standards
Test Standard : FCC PART 15 Subpart C(15.225)
Test Method : ANSI C 63.10 (2013)
Summary of Test Results
Standard Result Limit
15.203 Pass
15.207 Pass
15.225(a) Pass 15,848 uV/m
at 30 m
15.225(b) Pass 334 uV/m
at 30 m
15.225(c) Pass 106 uV/m
at 30 m
15.225(d) Pass
15.225(e) Pass
15.215(c) Pass
This standard sets forth uniform methods of measurement of radio-frequency (RF) signals and
noise emitted from both unintentional and intentional emitters of RF energy in the frequency range
9 kHz to 40 GHz. Methods for the measurement of radiated and AC power-line conducted radio
noise are covered and may be applied to any such equipment unless otherwise specified by
individual equipment requirements. These methods cover measurement of certain decides that
deliberately radiate energy, such as intentional emitters, but does not cover licensed transmitters.
This standard is not intended for certification/approval of avionic equipment or for industrial,
scientific, and medical (ISM) equipment These method apply to the measurement of individual
units or systems comprised of multiple units
This Standard sets out the regulations under which an intentional, unintentional, or incidental
radiator may be operated without an individual license. It also contains the technical
specifications, administrative requirements and other conditions relating to the marketing of Part
15 devices.
Apply section 15.209
(out side band of the 13.110
~14.010) MHz
Meet the requirement
Radiated Emission
(13.410 ~13.553 ,
13.567 ~ 13.710) MHz
Meet the requirement
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 5 of 18
Applied Satandard : 47 CFR Part 15, Subpart C
Test Type Remark
AC Power Conducted Emission Meet the requirement
Radiated Emission
(13.553 ~13.567) MHz Meet the requirement
20dB Bandwidth Meet the requirement
Frequency stability Meet the requirement
Radiated Emission
(13.110 ~13.410 ,
13.710 ~ 14.010) MHz
Meet the requirement
Antenna Requirement Meet the requirement
4. Measurement Condition
4.1 EUT Operation.
4.2 Configuration and Peripherals
-The EUT was tested, under transmission / receiving
1. Normal communication with RF OUT Frequeny(13.56 MHz).
2. Monitoring the operation status of frequency by using RF CARD.
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 6 of 18
4.3 EUT and Support equipment
Equipment Name Remark
(FCC ID)
Face Station2 EUT
Adapter
RF CARD
4.4 Cable Connecting
Name I/O port I/O port Length Shielded
Face Station2 Power - 2.0
Unshielded
Face Station2
Wireless
(13.56 MHz)
Wireless
(13.56 MHz)
--
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 7 of 18
Remark
Start Equipment
Name
End Equipment
ManufacturerS/N
NONE
Cable Standard
Model Name
NONEFS2-D
NONE
JPW128KA1200N05 NONE
RF CARD
Adapter
Suprema Inc
BridgePower Corp.
NONE
5. 20 dB Bandwidth
5.1 Procedure
5.2 20dB Bandwidth setup
Model Serial Number Cal. Due Data
FSV40 100939 4-Jan-18
5.3 Measurement Data
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 8 of 18
Decription
Signal Analyzer
The transmitter output was connected to the spectrum analyzer. The bandwidth of the fundamental
frequency was measured by spectrum analyzer. The 20 dB bandwidth is defined as the bandwidth at 20 dB
below from peak power point.
The spectrum analyzer is set to as following
RBW: 30 Hz
VBW: 300 Hz
Span: 5 kHz
Sweep:suitable duration based on the EUT specification
20dB Bandwidth Test Instruments
6. Frequency Tolerance
6.1 Procedure
6.2 Equipment lists
Model Serial Number Cal. Due Data
FSV40 100939 4-Jan-18
SM-150-2 04-TH24 4-Jan-18
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 10 of 18
Temp./Humidity Chamber
Signal Analyzer
The frequency stability of the transmitter is measured by:
a) Temperature: The temperature is varied from -20 ℃ to +50 ℃ using an environmental chamber.
b) Primary Supply Voltage: The primary supply voltage is varied from 85 % to 115 % of the voltage normally at the
input to the device or at the power supply terminals if cables are not normally supplied.
The frequency tolerance of the carrier shall be maintained within ±0.01 % of the operating frequency.
The following test equipments are used during test
Decription
6.3 Measurement Data (Adapter)
Operting Frequency : 13,560,191 Hz
Reference Voltage : 12.00 Vd.c.
Deviatin Limit : ± 0.01 %
Voltage Power Temperature
(%) (Vdc) ()
100 +20 (Ref)
100 -20
100 -10
100 0
100 10
100 20
100 30
100 40
100 50
85 10.20 20
115 15.84 20
Frequency Deviation
(Hz) (%)
12.00
13,560,232 0.000302
13,560,350 0.001173
13,560,238
0.001180
0.000347
13,560,280 0.000656
13,560,355 0.001209
13,560,219 0.000206
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 11 of 18
13,560,259 0.000501
13,560,468 0.002043
13,560,432 0.001777
13,560,518 0.002411
13,560,351
7. Measurement of radiated disturbance
7.1 Radiated emission limits, general requirements
Except as provided elsewhere in this Subpart, the emissions from an intentional radiator
shall not exceed the field strength levels specified in the following table:
Frequency
(MHz)
Field strength @30 m
(uV/m)
Field strength @3m
(dBuV/m)
Below 13.110 30 69.5
13.110 ~13.410 106 80.5
13.410~13.553 334 90.5
13.553~13.567 15,848 124
13.567~13.710 334 90.5
13.710~14.010 106 80.5
Above 14.010 30 69.5
7.2 Measurement equipments
Equipment Name Type Manufacturer Serial No. Next
Calibration date
TEST Receiver ESCI7 ROHDE & SCHWARZ 100916 5-Nov-17
Logbicon Antenna VULB 9168 SCHWARZBECK 193 12-Oct-18
Turn Table DT3000-2t Innco System GmbH N/A -
Antenna Mast MA4000-EP Innco System GmbH N/A -
Antenna Master &
Turn table controller
CO2000-P Innco System GmbH
CO2000/641
/28051111/L
-
Loop Antenna HFH2-Z2 ROHDE & SCHWARZ 100188 22-Aug-17
7.3 Environmental Condition
Test Place : 10 m Semi-anechoic chamber
Below 1 GHz
Temperature (°C) : 23.1 ℃
Humidity (% R.H.) : 49.5 % R.H.
Test Place : 3 m Semi-anechoic chamber
(
3 m
)
Above 1 GHz-N/A
Temperature (°C) :
Humidity (% R.H.) :
* dBuV/m=20*log(uV/m) * Distance factor=40dB / decade(15.31(f))
40.5
29.5
84
50.5
The EUT was placed on the top of a rotating table 0.8 m above the ground at a 10 m semi-anechoic chamber . The
table was rotated 360° to determine the position of the highest radiation.Then antenna is a loop antenna is fixed at 1 m
above the ground to determine the maximum value of the field strength. Both parallel and perpendicular of the antenna
are set to make the measurement. For each suspected emission, the EUT was arranged to its worst case and then the
table was turned from 0° to 360° to find the maximum reading. The test receiver system was set to Peak Detect
Function and Specified Bandwidth with Maximum Hold Mode.
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 13 of 18
40.5
50.5
Field strength @30 m
(dBuV/m)
29.5
7.4 Test data(9 kHz ~ 30 MHz)
Test Date : Measurement Distance : 3 m
Ant Factor
(dB)
Cable
(dB)
Limit
(dB㎶/m)
Result
(dB㎶/m)
Margin
(dB)
Noise Floor - - - - 19.30 0.5 69.5 - -
Noise Floor - - - - 19.30 0.5 80.5 - -
Noise Floor - - - - 19.30 0.5 90.5 - -
13.5600 38.97 180 ° X 0.8 19.30 0.4 124.0 58.71 65.29
Noise Floor - - - - 19.30 0.5 90.5 - -
Noise Floor - - - - 0.5 80.5 - -
Noise Floor - - - - 19.20 0.8 69.5 - -
Remark
Correction Factor Result Value(Quasi-Peak)
14.010 MHz to 30 MHz
Below 13.110 MHz
13.110 MHz to 13.410 MHz
13.410 MHz to 13.553 MHz
13.553 MHz to 13.567 MHz
13.567 MHz to 13.710 MHz
13.710 MHz to 14.010 MHz
Vertical
Position
[Angle]
9-Feb-17
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 14 of 18
*The 30 m limit was converted to 3 m Limit using square factor(x) as it was found by
measurements as follows;
*3 m Limit(dBuV/m) = 20log(X)+40log(30/3)= 20log(15848)+40log(30/3) = 124 dBuV
*3 m Limit(dBuV/m) = 20log(X)+40log(30/3)= 20log(30)+40log(30/3) = 69.5 dBuV
* The EUT was measured for the worst case by rotating of antenna angle.
* The EUT performed at X,Y,Z and recorded the worst data in the report.
Frequency
(MHz)
Reading
(dB㎶)
EUT
Position
Height
(m)
7.5 Test data(30 MHz ~ 1 000 MHz)
Test Date : 9-Feb-17
Measurement Distance :
3 m
Ant Factor
(dB)
Cable
(dB)
Limit
(dB㎶/m)
Result
(dB㎶/m)
Margin
(dB)
243.20 23.36 V 1.0 11.56 2.41 46.00 37.33 8.67
281.60 21.02 H 1.9 12.88 2.61 46.00 36.51 9.49
332.80 20.65 H 1.6 14.21 2.85 46.00 37.71 8.29
351.00 19.35 H 1.3 14.80 2.93 46.00 37.08 8.92
400.00 19.77 V 1.0 15.63 3.16 46.00 38.56 7.44
830.90 11.32 V 1.0 22.77 4.73 46.00 38.82 7.18
Remark
Result Value(Quasi-peak)Correction Factor
Height
(m)
Position
(V/H)
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 15 of 18
Frequency
(MHz)
Reading
(dB㎶)
H : Horizontal, V : Vertical
*Result Value = Reading + Antenna + Cable loss
*Correction Factor = Ant Factor + Cable
*The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120 kHz for
Quasi-peak detection
7.6 Test data (Above 1 GHz) - N / A
Test Date :
Measurement Distance :
3 m
Ant Factor
(dB)
Cable
(dB)
Limit
(dB㎶/m)
Result
(dB㎶/m)
Margin
(dB)
Remark
Result ValueCorrection Factor
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 16 of 18
Frequency
(MHz)
Reading
(dB㎶)
H : Horizontal, V : Vertical
*Reading = receiver reading + Amplifier Gain
*CL = Cable Loss-Amplifier Gain
*The resolution bandwidth and video bandwidth of spectrum analyzer is 1 MHz and 10 Hz for average detection at
frequency above 1 GHz.
*This test does not require because the highest operating frequency of the EUT is less than 108 MHz.
*Application method of the highest frequency is in the following
*Highest frequency of the EUT is less than 108 MHz, the measurement shall only be made up to 1 GHz.
*Highest frequency of the EUT is between 108 MHz and 500 MHz, the measurement shall only be made up to 2 GHz.
*Highest frequency of the EUT is between 500 MHz and 1 GHz, the measurement shall only be made up to 5 GHz.
*Highest frequency of the EUT is above 1 GHz, the measurement shall be made up to 10 times the highest frequency
or 40 GHz,
Peak(RBW:1 MHz VBW:1 MHz)
Average(RBW:1 MHz VBW:10 Hz)
Height
(m)
Position
(V/H)
8. Measurement of conducted disturbance
8.1 Measurement equipments
Equipment Name Type Manufacturer Serial No. Next Calibration
date
TEST RECEIVER ESPI Rohde & Schwarz 100005 4-Nov-17
LISN ESH3-Z5 Rohde & Schwarz 836679/025 4-Nov-17
Pulse Limiter ESH3Z2 Rohde & Schwarz NONE 4-Nov-17
8.2 Environmental Condition
Test Place : Shielded Room
Temperature (°C) : 22.1 ℃
Humidity (% R.H.) : 50.2 % R.H.
The continuous disturbance voltage of AC Mains in the frequency from 0.15 MHz to 30 MHz was
measured in accordance to FCC Part 15 & ANSI C 63.10 (2013) The test setup was made
according to FCC Part 15 & ANSI C 63.10 (2013) in a shielded Room. The EUT was placed on a
non-conductive table at least 0.8 m above the ground plan. A grounded vertical reference plane
was positioned in a distance of 0.4 m from the EUT. The distance from the EUT to other metal
surfaces was at least 0.8 m. The EUT was only earthen by its power cord through the line
impedance stabilizing network. The power cord has been bundled to a length of 1.0 m. The test
receiver with Quasi Peak detector complies with CISPR 16.
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 17 of 18
8.3 Test data
Test Date :
Lisn
(dB)
Cable
(dB)
Limit
(dB㎶)
Reading
(dB㎶)
Result
(dB㎶)
Limit
(dB㎶)
Reading
(dB㎶)
Result
(dB)
0.20 0.16 0.20 H 63.57 37.12 37.48 53.57 31.13 31.49
0.27 0.09 0.20 N 61.21 34.35 34.64 51.21 29.41 29.70
0.33 0.16 0.20 H 59.38 33.65 34.01 49.38 29.18 29.54
0.60 0.10 0.22 N 56.00 36.29 36.60 46.00 33.81 34.12
0.66 0.17 0.22 H 56.00 36.23 36.62 46.00 33.02 33.41
0.80 0.10 0.23 N 56.00 32.45 32.78 46.00 29.30 29.63
13.11 0.55 0.36 H 60.00 19.93 20.85 50.00 19.05 19.97
Remark
Average Value
H : Hot Line, N : Neutral Line
*Correction Factor = Lisn + Cable
*Result = Correction Factor + Reading
Report Number : ESTRFC1703-003 EST-P25-IO2-F04 (2016.01.01) Page 18 of 18
9-Feb-17
Correction Factor
Line
(H/N)
Frequency
(MHz)
Quasi-peak Value
Appendix 1. Special diagram
* HOT LINE
* NEUTRAL LINE
150 kHz 30 MHz
UNCAL
1 P
K
M
AXH
2 A
V
CLRW
R
SGL
TDF
6DB
dBµV
dBµV
RBW 9 kHz
MT 1 s
PREAMP OFFAtt 10 dB AUTO
PRN
1 MHz 10 MHz
0
10
20
30
40
50
60
70
80
CISPR-AV
Quasi-PK
Comment: ESTR-17-01108(13.56MHz)-HOT
Date: 9.FEB.2017 14:16:57
150 kHz 30 MHz
UNCAL
1 P
K
M
AXH
2 AV
CLRW
R
SGL
TDF
6DB
dBµV
dBµV
RBW 9 kHz
MT 1 s
PREAMP OFFAtt 10 dB AUTO
PRN
1 MHz 10 MHz
0
10
20
30
40
50
60
70
80
CISPR-AV
Quasi-PK
Comment: ESTR-17-01108(13.56MHz)-NEUTRAL
Date: 9.FEB.2017 14:20:34
Appendix 1. Antenna Requirement
Requlation
According to §15.203, an intentional radiator shall be designed to ensure that no
antenna other than that furnished by the responsible party shall be used with the
device. The use of a permanently attached antenna or of an antenna that uses a
unique coupling to the intentional radiator shall be considered sufficient to comply
with the provisions of this Section. The manufacturer may design the unit so that
a broken antenna can be replaced by the user, but the use of a standard antenna
jack or electrical connector is prohibited.
Result
-Complied
The transmitter has an PCB Patten Antenna.
Download: FS2-D Face Station2 Test Report DXX  rev01 Suprema Inc.
Mirror Download [FCC.gov]FS2-D Face Station2 Test Report DXX  rev01 Suprema Inc.
Document ID3349085
Application IDLxzJFR92NgRqhiWRpHRt4Q==
Document DescriptionDXX Test Report rev01
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize33.3kB (416266 bits)
Date Submitted2017-04-07 00:00:00
Date Available2017-04-04 00:00:00
Creation Date2017-03-20 14:08:34
Producing SoftwareAcrobat Distiller 9.0.0 (Windows)
Document Lastmod2017-04-07 10:14:35
Document TitleDXX Test Report rev01
Document CreatorPScript5.dll Version 5.2.2
Document Author: User

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : User
Create Date                     : 2017:03:20 14:08:34+09:00
Modify Date                     : 2017:04:07 10:14:35+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : User
Title                           : ESTRFC1703-003- Suprema Inc-FS2-D_13.56MHz_Report.xls
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2017:04:07 10:14:35+09:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:fb6eae1f-8ece-417f-b208-0f49eb004505
Instance ID                     : uuid:f265502b-7031-4513-87f0-5d62e35fbeb9
Page Count                      : 18