GRV-A52HPN Unlicensed National Information Infrastructure TX User Manual Mikrotikls SIA

Mikrotikls SIA Unlicensed National Information Infrastructure TX

FCC ID Filing: TV7GRV-A52HPN
Purchase on Amazon: Unlicensed National Information Infrastructure TX

Trouble Viewing? See the or view the HTML Version or PDF in frame
Page 1 of GRV-A52HPN Unlicensed National Information Infrastructure TX User Manual  Mikrotikls SIA
Page 2 of GRV-A52HPN Unlicensed National Information Infrastructure TX User Manual  Mikrotikls SIA
Page 3 of GRV-A52HPN Unlicensed National Information Infrastructure TX User Manual  Mikrotikls SIA
Page 4 of GRV-A52HPN Unlicensed National Information Infrastructure TX User Manual  Mikrotikls SIA
Page 5 of GRV-A52HPN Unlicensed National Information Infrastructure TX User Manual  Mikrotikls SIA

RouterBOARD	
  Groove	
  	
  
Quick	
  Setup	
  Guide	
  and	
  Warranty	
  Information	
  
The	
  RouterBOARD	
  Groove	
  comes	
  preinstalled	
  in	
  an	
  outdoor	
  case,	
  with	
  a	
  built-­‐in	
  wireless	
  interface,	
  
an	
  N-­‐Male	
  antenna	
  connector,	
  and	
  one	
  10/100	
  Ethernet	
  connector	
  which	
  supports	
  MDI-­‐X	
  auto	
  
detection.	
  The	
  device	
  is	
  packaged	
  with	
  a	
  24V	
  power	
  adapter,	
  a	
  PoE	
  injector	
  and	
  two	
  mounting	
  loops.	
  
Several	
  models	
  are	
  available	
  (dual	
  band,	
  single	
  band,	
  AP	
  and	
  CPE	
  variants).	
  	
  
First	
  use	
  
1.
2.
3.
4.
5.
6.
Connect	
  the	
  antenna	
  to	
  the	
  N-­‐Male	
  connector	
  
Twist	
  to	
  open	
  the	
  Groove	
  case,	
  connect	
  an	
  Ethernet	
  cable	
  to	
  the	
  Ethernet	
  port	
  
Use	
  the	
  provided	
  rubber	
  insulator	
  to	
  put	
  on	
  the	
  Ethernet	
  cable,	
  and	
  push	
  it	
  into	
  the	
  case	
  
opening,	
  so	
  that	
  the	
  opening	
  is	
  tightly	
  closed	
  
The	
  Groove	
  accepts	
  8-­‐30V	
  Passive	
  PoE	
  from	
  a	
  PoE	
  injector	
  
The	
  default	
  IP	
  address	
  from	
  Ether1	
  is	
  192.168.88.1	
  for	
  configuration	
  
Username	
  is	
  admin	
  and	
  there	
  is	
  no	
  password	
  
Depending	
  on	
  the	
  antenna	
  used,	
  you	
  must	
  set	
  it’s	
  gain	
  in	
  the	
  RouterOS	
  software	
  to	
  ensure	
  
that	
  EIRP	
  meets	
  the	
  limit	
  set	
  by	
  authorities.	
  This	
  is	
  done	
  in	
  the	
  Wireless	
  menu.	
  	
  
Powering	
  
The	
  board	
  accepts	
  powering	
  from	
  the	
  Ethernet	
  port	
  (Passive	
  PoE):	
  
•
Ethernet	
  port	
  accepts	
  passive	
  Power	
  over	
  Ethernet	
  8-­‐30V	
  DC.	
  Package	
  contains	
  a	
  24V	
  
adapter	
  and	
  a	
  PoE	
  injector.	
  
Maximum	
  power	
  consumption	
  of	
  the	
  device	
  is	
  4W.	
  
Booting	
  process	
  
Initial	
  connection	
  has	
  to	
  be	
  done	
  via	
  the	
  Ethernet	
  cable.	
  Open	
  192.168.88.1	
  in	
  your	
  web	
  browser,	
  and	
  choose	
  “Webfig”	
  for	
  
browser	
  based	
  configuration	
  or	
  “Winbox”	
  for	
  a	
  Windows	
  utility	
  with	
  the	
  same	
  functions.	
  Username	
  is	
  admin	
  and	
  there	
  is	
  no	
  
password.	
  In	
  case	
  IP	
  connection	
  is	
  not	
  available,	
  Winbox	
  can	
  be	
  used	
  to	
  connect	
  to	
  the	
  MAC	
  address	
  of	
  the	
  device.	
  More	
  
information	
  here:	
  http://wiki.mikrotik.com/wiki/First_time_startup	
  
In	
  case	
  you	
  wish	
  to	
  boot	
  the	
  device	
  from	
  network,	
  for	
  example	
  to	
  use	
  MikroTik	
  Netinstall,	
  hold	
  the	
  RESET	
  button	
  of	
  the	
  
device	
  when	
  starting	
  it	
  until	
  the	
  LED	
  light	
  turns	
  off,	
  and	
  Metal	
  will	
  start	
  to	
  look	
  for	
  Netinstall	
  servers.	
  
Mounting	
  
The	
  Groove	
  is	
  to	
  be	
  mounted	
  vertically,	
  so	
  that	
  the	
  Ethernet	
  cable	
  points	
  downwards.	
  	
  
If	
  you	
  wish	
  to	
  tighten	
  the	
  Groove	
  to	
  a	
  pole,	
  you	
  can	
  do	
  it	
  with	
  the	
  provided	
  mounting	
  loops.	
  The	
  Groove	
  comes	
  bundled	
  with	
  
two	
  mounting	
  loops	
  -­‐	
  guide	
  the	
  loops	
  around	
  the	
  Groove	
  though	
  the	
  provided	
  edge	
  markings,	
  and	
  around	
  the	
  pole	
  where	
  it	
  
will	
  be	
  mounted.	
  You	
  should	
  avoid	
  connecting	
  a	
  loose	
  Ethernet	
  cable	
  to	
  the	
  Ethernet	
  port,	
  secure	
  the	
  cable	
  to	
  a	
  wall	
  or	
  the	
  
pole,	
  so	
  that	
  the	
  cable	
  weight	
  is	
  not	
  pulling	
  the	
  port.	
  It	
  is	
  recommended	
  to	
  secure	
  the	
  Ethernet	
  cable	
  less	
  than	
  2m	
  from	
  the	
  
Groove	
  device.	
  This	
  is	
  to	
  ensure	
  that	
  the	
  cable	
  doesn't	
  damage	
  the	
  port	
  by	
  it's	
  weight,	
  or	
  doesn't	
  fall	
  out.	
  
  
  
See	
  www.routerboard.com	
  for	
  more	
  information.	
  Contact	
  [email protected]	
  for	
  support	
  questions.	
  	
  
  
22-Sep-15
Expansion	
  Slots	
  and	
  Ports	
  
•
•
Built	
  in	
  5GHz	
  or	
  2GHz	
  (or	
  both)	
  wireless	
  device	
  (depends	
  on	
  model),	
  1x1	
  MIMO	
  
One	
  10/100	
  Ethernet	
  port,	
  supporting	
  automatic	
  cross/straight	
  cable	
  correction	
  (Auto	
  MDI/X),	
  so	
  you	
  can	
  use	
  either	
  
straight	
  or	
  cross-­‐over	
  cable	
  for	
  connecting	
  to	
  other	
  network	
  devices.	
  The	
  Ethernet	
  port	
  accepts	
  8-­‐30V	
  DC	
  powering	
  
from	
  a	
  passive	
  PoE	
  injector.	
  
Buttons	
  and	
  Jumpers	
  
•
•
RouterOS	
  reset	
  jumper	
  hole	
  (no	
  direct	
  access,	
  board	
  has	
  removed	
  from	
  case)	
  –	
  resets	
  RouterOS	
  software	
  to	
  
defaults.	
  Must	
  short	
  circuit	
  the	
  metallic	
  sides	
  of	
  the	
  hole	
  (with	
  a	
  screwdriver,	
  for	
  example)	
  and	
  boot	
  the	
  device.	
  Hold	
  
screwdriver	
  in	
  place	
  until	
  RouterOS	
  configuration	
  is	
  cleared.	
  	
  	
  
RouterBOOT	
  reset	
  button	
  (access	
  through	
  the	
  plastic	
  door)	
  has	
  two	
  functions:	
  
o Hold	
  this	
  button	
  during	
  boot	
  time	
  until	
  LED	
  light	
  starts	
  flashing,	
  	
  
release	
  the	
  button	
  to	
  reset	
  RouterOS	
  configuration	
  (same	
  result	
  as	
  with	
  reset	
  hole)	
  
o Hold	
  this	
  button	
  during	
  boot	
  time	
  longer,	
  until	
  LED	
  turns	
  off,	
  	
  
then	
  release	
  it	
  to	
  make	
  the	
  device	
  look	
  for	
  Netinstall	
  servers.	
  
Operating	
  System	
  Support	
  
Currently	
  tested	
  operating	
  system	
  is	
  MikroTik	
  RouterOS	
  (starting	
  from	
  version	
  v5.0).	
  
Copyright	
  and	
  Trademarks.	
  
Copyright	
  MikroTikls	
  SIA.	
  This	
  manual	
  contains	
  information	
  protected	
  by	
  copyright	
  law.	
  No	
  part	
  of	
  it	
  may	
  be	
  reproduced	
  or	
  
transmitted	
  in	
  any	
  form	
  without	
  prior	
  written	
  permission	
  from	
  the	
  copyright	
  holder.	
  RouterBOARD,	
  RouterOS,	
  RouterBOOT	
  
and	
  MikroTik	
  are	
  trademarks	
  of	
  MikroTikls	
  SIA.	
  All	
  trademarks	
  and	
  registered	
  trademarks	
  appearing	
  in	
  this	
  manual	
  are	
  the	
  
property	
  of	
  their	
  respective	
  holders.	
  
Hardware.	
  MikroTik	
  warrants	
  all	
  RouterBOARD	
  series	
  equipment	
  for	
  the	
  term	
  of	
  one	
  year	
  from	
  the	
  shipping	
  date	
  to	
  be	
  free	
  
of	
  defects	
  in	
  materials	
  and	
  workmanship	
  under	
  normal	
  use	
  and	
  service,	
  except	
  in	
  case	
  of	
  damage	
  caused	
  by	
  mechanical,	
  
electrical	
  or	
  other	
  accidental	
  or	
  intended	
  damages	
  caused	
  by	
  improper	
  use	
  or	
  due	
  to	
  wind,	
  rain,	
  fire	
  or	
  other	
  acts	
  of	
  nature.	
  
To	
  return	
  failed	
  units	
  to	
  MikroTik,	
  you	
  must	
  perform	
  the	
  following	
  RMA	
  (Return	
  Merchandise	
  Authorization)	
  procedure.	
  
Follow	
  the	
  instructions	
  below	
  to	
  save	
  time,	
  efforts,	
  avoid	
  costs,	
  and	
  improve	
  the	
  speed	
  of	
  the	
  RMA	
  process.	
  
1.
2.
3.
If	
  you	
  have	
  purchased	
  your	
  product	
  from	
  a	
  MikroTik	
  Reseller,	
  please	
  contact	
  the	
  Reseller	
  company	
  regarding	
  all	
  
warranty	
  and	
  repair	
  issues,	
  the	
  following	
  instructions	
  apply	
  ONLY	
  if	
  you	
  purchased	
  your	
  equipment	
  directly	
  from	
  
MikroTik	
  in	
  Latvia.	
  
We	
  do	
  not	
  offer	
  repairs	
  for	
  products	
  that	
  are	
  not	
  covered	
  by	
  warranty.	
  Exceptions	
  can	
  be	
  made	
  for	
  RB1000,	
  RB1100	
  
and	
  RB1200.	
  
Out-­‐of-­‐warranty	
  devices	
  and	
  devices	
  not	
  covered	
  by	
  warranty	
  sent	
  to	
  Mikrotikls	
  will	
  be	
  returned	
  to	
  the	
  sender	
  at	
  
sender's	
  cost.	
  
RMA	
  Instructions	
  are	
  located	
  on	
  our	
  webpage	
  here:	
  http://rma.mikrotik.com	
  
Manual.	
  This	
  manual	
  is	
  provided	
  “as	
  is”	
  without	
  a	
  warranty	
  of	
  any	
  kind,	
  expressed	
  or	
  implied,	
  including,	
  but	
  not	
  limited	
  to,	
  
the	
  implied	
  warranty	
  of	
  merchantability	
  and	
  fitness	
  for	
  a	
  particular	
  purpose.	
  The	
  manufacturer	
  has	
  made	
  every	
  effort	
  to	
  
ensure	
  the	
  accuracy	
  of	
  the	
  contents	
  of	
  this	
  manual,	
  however,	
  it	
  is	
  possible	
  that	
  it	
  may	
  contain	
  technical	
  inaccuracies,	
  
typographical	
  or	
  other	
  errors.	
  No	
  liability	
  is	
  assumed	
  for	
  any	
  inaccuracy	
  found	
  in	
  this	
  publication,	
  nor	
  for	
  direct	
  or	
  indirect,	
  
incidental,	
  consequential	
  or	
  other	
  damages	
  that	
  may	
  result	
  from	
  such	
  an	
  inaccuracy,	
  including,	
  but	
  not	
  limited	
  to,	
  loss	
  of	
  data	
  
or	
  profits.	
  Please	
  report	
  any	
  inaccuracies	
  found	
  to	
  [email protected]	
  
See	
  www.routerboard.com	
  for	
  more	
  information.	
  Contact	
  [email protected]	
  for	
  support	
  questions.	
  	
  
  
22-Sep-15
Federal Communication Commission Interference
Statement (FCC ID: TV7GRV-A52HPN)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This device and its antenna must not be co-located or operation in conjunction with any other
antenna or transmitter.
IMPORTANT: Exposure to Radio Frequency Radiation.
63 cm minimum distance has to be maintained between the antenna and the occupational user and
152 cm to general public. Under such configuration, the FCC radiation exposure limits set forth for an
population/uncotrolled environment can be satisfied.
Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the
authorized antennas in the United States (or where FCC rules apply); only those antennas certified
with the product are used. The use of any antenna other than those certified with the product is
expressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure the
output power level of antennas, according to country regulations and per antenna type. Professional
installation is required of equipment with connectors to ensure compliance with health and safety
issues.
LIST	
  OF	
  APPROVED	
  2GHz	
  ANTENNAS:	
  	
  
•
•
•
•
•
24	
  dBi	
  Dish	
  DC	
  24-­‐HD-­‐PFIP	
  
20	
  dBi	
  Panel	
  WLP-­‐2450-­‐20	
  
17	
  dBi	
  Sector	
  SA	
  24-­‐90-­‐17-­‐WB	
  	
  
15	
  dBi	
  Omni	
  Directional	
  (pole)	
  WL0-­‐2450-­‐15	
  	
  
13	
  dBi	
  Omni	
  Directional	
  (hor.	
  Polarization)	
  HP,	
  0DH	
  24-­‐13	
  
See www.routerboard.com for more information. Contact [email protected]
•
•
•
  	
  
LIST	
  OF	
  APPROVED	
  5GHz	
  ANTENNAS:	
  	
  
  
8.5	
  dBi	
  Omni	
  MTI	
  	
  Wireless	
  MT-­‐482016NA	
  
24	
  dBi	
  Panel	
  Pacific	
  Wireless	
  PA58-­‐24	
  
32	
  dBi	
  Dish	
  Pacific	
  Wireless	
  HDDA5W-­‐32-­‐DP	
  
22-Sep-15
Industry Canada (IC:7442A-GRVA52HPN)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
LE-LAN device restriction:
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
Users should also be advised that high-power radars are allocated as primary users (i.e.
priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars
could cause interference and/or damage to LE-LAN devices.
les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement
pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux
Les utilisateurs devraient aussi être avisés, d’une part, que les utilisateurs de radars de
haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) des
bandes de 5 250 à 5 350 MHz et de 5 650 à 5 850 MHz et, d’autre part, que ces radars
pourraient causer du brouillage et/ou des dommages aux dispositifs de RL-EL
See www.routerboard.com for more information. Contact [email protected]
22-Sep-15
CE Declaration of Conformity
Full Declaration of Conformity (DoC) may be obtained by visiting this web page:
http://routerboard.com/doc/
[EN] English
[BG] Bulgarian
[CZ] Czech
[DK] Danish
[DE] German
[EE] Estonian
[GR] Greek
[ES] Spanish
[IT] Italian
[LV] Latvian
[LT] Lithuanian
[HU] Hungarian
[NL] Dutch
[PL] Polish
[PT] Portuguese
[RO] Romanian
[SK] Slovak
[SI] Slovenian
[FI] Finish
[SE] Swedish
[NO] Norwegian
Hereby, MIKROTĪKLS SIA declares that this ROUTERBOARD is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
С настоящето, MIKROTĪKLS SIA декларира, че ROUTERBOARD е в съответствие със съществените изисквания и другитеприложими
разпоредби на Директива 1999/5/EC.
MIKROTĪKLS SIA tímto prohlašuje, že ROUTERBOARD splňuje základní požadavky a všechna příslušná ustanoveni Směrnice 1999/5/ES.
Undertegnede MIKROTĪKLS SIA erklærer herved, at følgende udstyr ROUTERBOARD overholder de væsentlige krav og øvrige relevante krav i
direktiv 1999/5/EF.
Hiermit erklärt MIKROTĪKLS SIA dass sich das Gerät ROUTERBOARD in Übereinstimmung mit den grundlegenden Anforderungen und den
übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Käesolevaga kinnitab MIKROTĪKLS SIA seadme ROUTERBOARD vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele sätetele.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ MIKROTĪKLS SIA ΔΗΛΩΝΕΙ ΟΤΙ ROUTERBOARD ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ
ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ
Por la presente, MIKROTĪKLS SIA declara que este ROUTERBOARD cumple con los requisitos esenciales y otras exigencias relevantes de la
Directiva 1999/5/EC.
Con la presente MIKROTĪKLS SIA dichiara che questo ROUTERBOARD è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti
stabilite dalla direttiva 1999/5/CE.
Ar šo MIKROTĪKLS SIA deklarē, ka ROUTERBOARD atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Šiuo MIKROTĪKLS SIA deklaruoja, kad šis ROUTERBOARD atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas
A MIKROTĪKLS SIA ezzennel kijelenti, hogy a ROUTERBOARD típusú beren-dezés teljesíti az alapvető követelményeket és más 1999/5/EK
irányelvben meghatározott vonatkozó rendelkezéseket.
Hierbij verklaart MIKROTĪKLS SIA dat het toestel l ROUTERBOARD in overeenstemming is met de essentiële eisen en de andere relevante
bepalin-gen van richtlijn 1999/5/EG.
Niniejszym MIKROTĪKLS SIA deklaruje że ROUTERBOARD jest zgodny z zasadniczymi wymaganiami i innymi właściwymi postanowieniami
Dyrektywy 1999/5/EC.
Eu, MIKROTĪKLS SIA declaro que o ROUTERBOARD cumpre os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.
Prin prezenta, MIKROTĪKLS SIA declară că aparatul ROUTERBOARD este în conformitate cu cerinţele esenţiale şi cu alte prevederi pertinente
ale Directivei 1999/5/CE..
MIKROTĪKLS SIA týmto vyhlasuje, že ROUTERBOARD spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
MIKROTĪKLS SIA izjavlja, da je ta ROUTERBOARD v skladu z bistvenimi zahtevami in drugimi relevantnimi določili direktive 1999/5/ES.
MIKROTĪKLS SIA vakuuttaa täten että ROUTERBOARD tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien
direktiivin muiden ehtojen mukainen.
Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i direktiv 1999/5/EC.
MIKROTĪKLS SIA Erklærer herved at ROUTERBOARD er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
EN. Instruction manual: Connect the power adapter to turn on the device. Open 192.168.88.1 in your web browser, to configure it. More information on
http://wiki.mikrotik.comBG. Инструкция: Свържете адаптера на захранване, за да включите устройството. Отворете 192.168.88.1 в уеб браузър, за да
настроите продукта. Повече информация в http://wiki.mikrotik.com CZ. Návod k použit: Připojte napájecí adaptér k zapnutí přístroje. Otevřete
192.168.88.1 ve webovém prohlížeči pro konfiguraci produktu. Více informací najdete v http://wiki.mikrotik.com DK. Instruktionsbog: Tilslut strømadapteren
for at tænde for enheden. Åbn 192.168.88.1 i en webbrowser til at konfigurere produktet. Mere information i http://wiki.mikrotik.com FR. Mode d'emploi:
Connectez l'adaptateur d'alimentation pour allumer l'appareil. Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit. Plus d'informations
dans http://wiki.mikrotik.com DE. Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gerät einzuschalten. Öffnen Sie 192.168.88.1 in einem WebBrowser, um das Produkt zu konfigurieren. Weitere Informationen im http://wiki.mikrotik.com EE. Kasutusjuhend: Ühendage toiteadapter seadme
sisselülitamiseks. Avatud 192.168.88.1 in veebilehitseja seadistada toodet. Rohkem teavet http://wiki.mikrotik.com ES. Manual de instrucciones: Conecte el
adaptador de alimentación para encender la unidad. Abra 192.168.88.1 en un navegador web para configurar el producto. Más información en
http://wiki.mikrotik.com IT. Manuale di istruzioni: Collegare l'adattatore di alimentazione per accendere l'unità. Aprire 192.168.88.1 in un browser Web per
configurare il prodotto. Maggiori informazioni in http://wiki.mikrotik.com LV. Lietošanas instrukcija: Pievienojiet Strāvas adapteri, lai ieslēgtu ierīci. Atvērt
192.168.88.1 ar interneta pārlūku, lai konfigurētu produktu. Plašāka informācija http://wiki.mikrotik.com LT. Naudojimosi instrukcija: Prijunkite maitinimo
adapterį įjunkite įrenginį. Į interneto naršyklę 192.168.88.1 Atidarykite galite konfigūruoti gaminį. Daugiau informacijos rasite http://wiki.mikrotik.com HU.
Használati utasítás: Csatlakoztassa a hálózati adaptert a készülék bekapcsolásához. Megnyitása 192.168.88.1 egy webböngészőben beállítani a terméket.
Több információ http://wiki.mikrotik.com NL. Handleiding: Sluit voedingsadapter aan op het apparaat in te schakelen. Open 192.168.88.1 in een webbrowser
om het product te configureren. Meer informatie in http://wiki.mikrotik.com PL. Instrukcja obsługi: Podłącz adapter zasilania, aby włączyć urządzenie.
Otwórz 192.168.88.1 w przeglądarce internetowej, aby skonfigurować urządzenie. Więcej informacji w http://wiki.mikrotik.com PT. Manual de instruções:
Conecte o adaptador de alimentação para ligar o aparelho. Abra 192.168.88.1 em um navegador da web para configurar o produto. Mais informações em
http://wiki.mikrotik.com RO. Instrucțiuni de utilizare : Conectaţi adaptorul de alimentare pentru a porni aparatul. Deschide 192.168.88.1 într-un browser
web pentru a configura produsul. Mai multe informaţii în http://wiki.mikrotik.com SK. Návod na použitie: Pripojte napájací adaptér k zapnutiu prístroja.
Otvorte 192.168.88.1 vo webovom prehliadači pre konfiguráciu produktu. Viac informácií nájdete v http://wiki.mikrotik.com SI. Navodila: Priključite
napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Več informacij v http://wiki.mikrotik.com FI. Käyttöohje: Kytke
virtalähde päälle laitteen. Avaa 192.168.88.1 in selaimen määrittää tuotteen. Lisää tietoa http://wiki.mikrotik.com SE. Instruktionsmanual: Anslut
nätadaptern för att slå på enheten. Öppna 192.168.88.1 i en webbläsare för att konfigurera produkten. Mer information på http://wiki.mikrotik.com NO.
Bruksanvisningen: Koble strømadapteren for å slå på enheten. Åpne 192.168.88.1 i en nettleser for å konfigurere produktet. Mer informasjon på
http://wiki.mikrotik.com GR. εγχειρίδιο οδηγιών: Συνδέστε τον προσαρμογέα τροφοδοσίας για να ενεργοποιήσετε τη μονάδα. Ανοίξτε 192.168.88.1 σε ένα
πρόγραμμα περιήγησης στο Web για να διαμορφώσετε το προϊόν. Περισσότερες πληροφορίες στο http://wiki.mikrotik.com
See www.routerboard.com for more information. Contact [email protected] for support questions.
22-Sep-15
Download: GRV-A52HPN Unlicensed National Information Infrastructure TX User Manual  Mikrotikls SIA
Mirror Download [FCC.gov]GRV-A52HPN Unlicensed National Information Infrastructure TX User Manual  Mikrotikls SIA
Document ID3413494
Application ID/aMAfFkUjC9cRUI/uK7otg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize121.23kB (1515412 bits)
Date Submitted2017-06-05 00:00:00
Date Available2017-06-05 00:00:00
Creation Date0000-00-00 00:00:00
Document Lastmod0000-00-00 00:00:00
Document TitleUser Manual

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
Linearized                      : No
PDF Version                     : 1.4
Page Count                      : 5
Title                           : 
Producer                        : 
Creator                         : 
Subject                         : 
Author                          : 

Facebook Twitter Google+ RSS © FCCID.io 2017