EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG

u-blox AG WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1

Page 1 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 2 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 3 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 4 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 5 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 6 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 7 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 8 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 9 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 10 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 11 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 12 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 13 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 14 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 15 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 16 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 17 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 18 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 19 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 20 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 21 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 22 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 23 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 24 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 25 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 26 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 27 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 28 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 29 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Page 30 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG

FCC Measurement/Technical Report on
WLAN/Bluetooth/NFC module
EMMY-W161 and EMMY-W163
NFC part
Re por t Re fe r e n ce : MDE_UBLOX_1551_FCCe_Rev.1
FCC ID:
EMMY-W161: XPYEMMYW161
EMMY-W163: XPYEMMYW163
IC ID:
EMMY-W161: 8595A-EMMYW161
EMMY-W163: 8595A-EMMYW163
Te st La bora t or y :
7layers GmbH
Borsigstrasse 11
40880 Ratingen
Germany
Note:
The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts
without the written approval of the test laboratory.
7 la ye r s Gm bH
Geschäftsführer/
Borsigstraße 11
Managing Directors:
Registergericht/registered:
a Bureau Verit as
40880 Ratingen, Germany
Frank Spiller
Düsseldorf HRB 75554
Group Com pany
T +49 (0) 2102 749 0
Bernhard Retka
USt-Id.-Nr./VAT-No. DE203159652
F +49 (0) 2102 749 350
Alexandre Norré-Oudard
Steuer-Nr./TAX-No. 147/5869/0385
Commerzbank AG Account No. 303 016 000 Bank Code 300 400 00
www.7layers.com
IBAN DE81 3004 0000 0303 0160 00 Swift Code COBADEFF
Ta ble of Con t e n t s
Su m m a r y
0.1
Technical Report Summary
0.2
Measurement Summary
Re vision H ist or y
Adm in ist r a t ive D a t a
1.1
1.2
1.3
1.4
Te st obj e ct D a t a
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
Testing Laboratory
Project Data
Applicant Data
Manufacturer Data
General EUT Description
EUT Main components
Ancillary Equipment
Auxiliary Equipment
EUT Setups
Operating Modes
Special software used for testing
Product labelling
Te st Re su lt s
3.1
3.2
3.3
3.4
3.5
Conducted Emissions AC Power line
Spurious radiated emissions
Occupied bandwidth
Spectrum mask
Frequency tolerance
12
16
17
18
Te st Equ ipm e n t
21
Ph ot o Re por t
23
Se t u p D r a w in gs
23
FCC a n d I C Cor r e la t ion of m e a su r e m e n t r e qu ir e m e n t s 2 4
An n e x m e a su r e m e n t plot s
8.1
8.2
8.3
8.4
Radiated emissions
AC Mains conducted
Occupied bandwidth
Spectrum mask
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
25
25
27
29
30
Page 2 of 30
0
Su m m a r y
0 .1 Te ch n ica l Re por t Su m m a r y
Type of Aut h or iza t ion
Certification for an intentional radiator operating at 13.56 MHz
Applica ble FCC Ru le s
Prepared in accordance with the requirements of FCC Rules and Regulations as listed in
47 CFR Ch.1 Parts 2 (10-1-15 Edition) and 15 (10-1-15 Edition). The following subparts
are applicable to the results in this test report.
Part 2, Subpart J - Equipment Authorization Procedures, Certification
Part 15, Subpart C – Intentional Radiators
§ 15.205
Restricted bands of operation
§ 15.207
Conducted limits
§ 15.209
Radiated emission limits; general requirements
§ 15.215
Additional provisions to the general radiated emission limitations
§ 15.225
Operation within the band 13.110-14.010 MHz
ANSI C63.10-2013 is applied
Sum m a r y Te st Re su lt s:
Th e EUT com plie d w it h a ll pe r for m e d t e st s a s list e d in ch a pt e r 0 .2 M e a sur e m e n t
Sum m a r y.
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 3 of 30
0 .2 M e a su r e m e n t Su m m a r y
FCC Pa r t 1 5 , Subpa r t C
§ 1 5 .2 0 7
Conducted Emissions AC Power line
The measurement was performed according to ANSI C63.10
OP- M ode
Se t up
Por t
op-mode 1
Setup_01
DC power supply
2013
Fina l Re sult
passed
FCC Pa r t 1 5 , Subpa r t C
§ 1 5 .2 0 9
Radiated Emissions
The measurement was performed according to ANSI C63.10
OP- M ode
Se t up
Por t
op-mode 1
Setup_01
NFC antenna
2013
Fina l Re sult
passed
FCC Pa r t 1 5 , Subpa r t C
§ 1 5 .2 1 5
Occupied Bandwidth
The measurement was performed according to ANSI C63.10
OP- M ode
Se t up
Por t
op-mode 1
Setup_02
NFC antenna
2013
Fina l Re sult
passed
FCC Pa r t 1 5 , Subpa r t C
§ 1 5 .2 2 5
Spectrum Mask
The measurement was performed according to ANSI C63.10
OP- M ode
Se t up
Por t
op-mode 1
Setup_01
NFC antenna
2013
Fina l Re sult
passed
FCC Pa r t 1 5 , Subpa r t C
§ 1 5 .2 2 5
Frequency Tolerance
The measurement was performed according to ANSI C63.10
OP- M ode
Se t up
Por t
op-mode 2
Setup_01
NFC antenna
2013
Fina l Re sult
passed
Re vision H ist or y
Ve r sion
initial
Rev.1
Re le a se da t e
2016-03-30
2016-04-01
Responsible for
Accreditation Scope:
Re por t ve r sion con t r ol
Ch a n ge D e scr ipt ion
Ve r sion va lidit y
invalid
Page 1: Change of FCC ID and IC ID. valid
Page 7: Change of Type Designation
from W161 to EMMY-W161 and
W163 to EMMY-W163.
--
WOLFGANG PETER
RICHTER
2016.04.01 18:19:41
+02'00'
Responsible
for Test Report:
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
DOBRIN TODOROV DOBRINOV
2016.04.01 18:15:47 +02'00'
Page 4 of 30
1
Adm in ist r a t ive D a t a
1 .1 Te st in g La bor a t or y
Company Name:
7layers GmbH
Address
Borsigstr. 11
40880 Ratingen
Germany
This facility has been fully described in a report submitted to the FCC and accepted
under the registration number 96716.
The test facility is also accredited by the following accreditation organisation:
Laboratory accreditation no.:
DAkkS D-PL-12140-01-01
Responsible for Accreditation Scope:
Report Template Version:
Dipl.-Ing. Bernhard Retka
Dipl.-Ing. Robert Machulec
Dipl.-Ing. Andreas Petz
Dipl.-Ing. Marco Kullik
Dipl.-Ing. Wolfgang Richter
2015-08-24
1 .2 Pr oj e ct D a t a
Responsible for testing and report:
Dipl.-Ing. Dobrin Dobrinov
Date of Test(s):
Date of Report:
2016-01-04 to 2016-01-12
2016-04-01
1 .3 Applica n t D a t a
Company Name:
Address:
u-blox AG
Zürcherstrasse 68
8800 Thalwil
Switzerland
Contact Person:
Mr. Giulio Comar
1 .4 M a n u fa ct u r e r D a t a
Company Name:
please see applicant data
Address:
Contact Person:
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 5 of 30
2
Te st obj e ct D a t a
2 .1 Ge n e r a l EUT D e scr ipt ion
Equ ipm e n t u n de r Te st
Type D e sign a t ion :
Kin d of D e vice :
( opt iona l)
Volt a ge Type :
Volt a ge le ve l:
WLAN/Bluetooth/NFC module
EMMY-W161 and EMMY-W163
NFC transceiver at 13.56 MHz
DC
3.3 V
Ge n e r a l pr odu ct de scr ipt ion :
EMMY-W161 and EMMY-W163 are ultra-compact multi-radio modules providing Wi-Fi,
Classic Bluetooth, Bluetooth low energy and NFC mode of operation.
It is designed for both simultaneous and independent operations of:
• Wi-Fi IEEE 802.11ac and a/b/g/n
• Dual-mode Bluetooth 4.2
• NFC
Spe cific pr odu ct de scr ipt ion for t h e EUT:
EMMY-W161: Shielded module, single antenna pin for WLAN 802.11 ac/a/b/g/n and
Bluetooth communication
EMMY-W163: Shielded module, separate antenna pins for WLAN 802.11 ac/a/b/g/n and
Bluetooth communication
According to the applicant, there is no difference between the two modules, regarding
NFC parameters and functionality.
Th e EUT pr ovide s t h e follow in g por t s:
Por t s
- DC power supply
- NFC antenna
Th e m a in com pon e n t s of t h e EUT a r e list e d a nd de scr ibe d in Cha pt e r 2 .2 .
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 6 of 30
2 .2 EUT M a in com pon e n t s
Type , S/ N , Sh or t D e scr ipt ion s e t c. u se d in t h is Te st Re por t
Sh or t
D e scr ipt ion
EUT A
(Code:
DE1015031aa01)
Remark: EUT A is
EUT B
(Code:
DE1015032ca01)
Remark: EUT B is
Equ ipm e n t
u n de r Te st
RFID
transceiver
Type
D e sign a t ion
EMMY-W161
Se r ia l N o.
H W St a t u s
SW St a t u s
‒
03
n/a
connected to evaluation board equipped with PCB loop antenna.
RFID
EMMY-W163
‒
03
n/a
transceiver
D a t e of
Re ce ipt
2015-12-08
2015-12-08
connected to evaluation board equipped with PCB loop antenna.
N OTE: Th e sh or t de scr ipt ion is u se d t o sim plify t h e ide n t ifica t ion of t h e EUT in t h is t e st
r e por t .
2 .3 An cilla r y Equ ipm e n t
For the purposes of this test report, ancillary equipment is defined as equipment which is
used in conjunction with the EUT to provide operational and control features to the EUT.
It is necessary to configure the system in a typical fashion, as a customer would normally
use it. But nevertheless Ancillary Equipment can influence the test results.
Sh or t
D e scr ipt ion
‒
Equ ipm e n t
u n de r Te st
‒
Type
D e sign a t ion
‒
Se r ia l N o.
H W St a t u s
SW St a t u s
FCC I D
‒
‒
‒
‒
2 .4 Au x ilia r y Equ ipm e n t
For the purposes of this test report, auxiliary equipment is defined as equipment which is
used temporarily to enable operational and control features especially used for the tests
of the EUT which is not used during normal operation or equipment that is used during
the tests in combination with the EUT but is not subject of this test report. It is necessary
to configure the system in a typical fashion, as a customer would normally use it.
But nevertheless Auxiliary Equipment can influence the test results.
Sh or t
D e scr ipt ion
AUX 1
Equ ipm e n t
u n de r Te st
Laptop
AUX 2
AC/DC
adapter
AUX 3
Evaluation
board
AC/DC
power
supply
AUX 4
Type
D e sign a t ion
Acer
Mod: LD1
Liteon
Technology
Corporation
EVB-EMMY161
PeakTech
6005D
Se r ia l n o.
H W St a t u s
SW St a t u s
FCC I D
8210205723
Linux
8312774105
Rev:A05
02
n/a
081062045
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 7 of 30
2 .5 EUT Se t u ps
This chapter describes the combination of EUTs and equipment used for testing. The
rationale for selecting the EUTs, ancillary and auxiliary equipment and interconnecting
cables, is to test a representative configuration meeting the requirements of the
referenced standards.
Se t u p N o.
Setup_01
Com bin a t ion of EUTs
EUT A + AUX 4
Setup_02
EUT B + AUX 4
D e scr ipt ion a n d Ra t ion a le
Setup for Frequency Tolerance, Spectrum Mask, AC Power
Line and Occupied BW tests
Setup for Spurious Emissions tests
2 .6 Ope r a t in g M ode s
This chapter describes the operating modes of the EUTs used for testing.
Op. M ode
op-mode 1
D e scr ipt ion of Ope r a t in g M ode s
modulated carrier signal
op-mode 2
CW carrier signal
Re m a r k s
EUT is transmitting a periodic modulated signal
and is continuously reading TAG information.
EUT is transmitting a non-modulated signal
2 .7 Spe cia l soft w a r e u se d for t e st in g
Using AUX 1 to AUX 3 and a Marvell software provided by the applicant, it is possible to
set the EUT operating modes.
2 .8 Pr odu ct la be llin g
2 .8 .1
FCC I D la be l
Please refer to the customer documentation.
2 .8 .2 I C I D la be l
Please refer to the customer documentation.
2 .8 .3
Loca t ion of t h e la be l on t he EUT
Please refer to the customer documentation.
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 8 of 30
3
Te st Re su lt s
3 .1 Con du ct e d Em ission s AC Pow e r lin e
St a n da r d
FCC Part 15, 10-1-15 Edition Subpart C
Th e t e st w a s pe r for m e d a ccor din g t o: ANSI C63.10–2013 + KDB 174176 D01
3 .1 .1 Te st D e scr ipt ion
The test set-up was made in accordance to the general provisions of ANSI C 63.10
The Equipment Under Test (EUT) was setup in a shielded room to perform the conducted
emissions measurements in a typical installation configuration. The EUT was powered
from 50µH || 50 Ohm Line Impedance Stabilization Network (LISN). The LISN’s unused
connections were terminated with 50 Ohm loads.
The measurement procedure consists of two steps. It is implemented into the EMI test
software EMC-32 from R&S.
St e p 1 : Pr e lim ina r y sca n
Intention of this step is, to determine the conducted EMI-profile of the EUT.
EMI receiver settings:
- Detector: Peak – Maxhold & Average
- Frequency range: 150 kHz – 30 MHz
- Frequency steps: 2.5 kHz
- IF–Bandwidth: 9 kHz
- Measuring time / Frequency step: 100 ms (FFT-based)
- Measurement on phase + neutral lines of the power cords
On basis of this preliminary scan the highest amplitudes and the corresponding
frequencies relative to the limit are identified. Emissions above the limit and emissions
which are in the 10 dB range below the limit are considered.
St e p 2 : Fina l m e a su r e m e n t
Intention of this step is, to determine the highest emissions with the settings defined in
the test specification for the frequencies identified in step 1.
EMI receiver settings:
- Detector: Quasi-Peak
- IF Bandwidth: 9 kHz
- Measuring time: 1 s / frequency
At each frequency determined in step 1, four measurements are performed in the
following combinations:
1) Neutral lead - reference ground (PE grounded)
2) Phase lead - reference ground (PE grounded)
3) Neutral lead - reference ground (PE floating)
4) Phase lead - reference ground (PE floating)
The highest value is reported.
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 9 of 30
KD B 1 7 4 1 7 6 D 0 1 , Q5 . D e vice s Ope r a t ing Be low 3 0 M H z
For a device with a permanent or detachable antenna operating at or below 30 MHz, the
FCC will accept measurements performed with a suitable dummy load in lieu of the
antenna under the following conditions:
(1) perform the AC power-line conducted tests with the antenna connected to determine
compliance with Section 15.207 limits outside the transmitter's fundamental emission
band;
(2) retest with a dummy load in lieu of the antenna to determine compliance with Section
15.207 limits within the transmitter's fundamental emission band.
For a detachable antenna, remove the antenna and connect a suitable dummy load to the
antenna connector. For a permanent antenna, remove the antenna and terminate the RF
output with a dummy load or network which simulates the antenna in the fundamental
frequency band.
3 .1 .2 Te st Re qu ir e m e n t s / Lim it s
FCC Part 15, Subpart C, §15.207
Frequency Range (MHz)
0.15 – 0.5
0.5 – 5
5 – 30
QP Limit (dBµV)
66 to 56
56
60
AV Limit (dBµV)
56 to 46
46
50
Used conversion factor: Limit (dBµV) = 20 log (Limit (µV)/1µV).
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 10 of 30
3 .1 .3 Te st Pr ot ocol
Temperature:
Air Pressure:
Humidity:
23 °C
1010 hPa
35 %
Op. M ode
op-mode 1
Se t up
Setup_01
Por t
DC Port (power line)
Measurements are performed according to KDB 174176 D01
Step (1). Measurements performed with the EUT dedicated antenna
Frequency
(MHz)
13.454250
13.560000
13.560000
13.665750
QuasiPeak
(dBµV)
Average
(dBµV)
48.64
--62.89
49.04
Limit
(dBµV)
--62.59
-----
60.00
50.00
60.00
60.00
Margin
(dB)
11.36
-12.59
-2.89
10.96
Line
L1
PE
GND
GND
GND
GND
Step (2). Measurements provided with a dummy antenna
Frequency
(MHz)
0.217500
0.339000
13.348500
13.454250
13.454250
13.560000
13.560000
13.665750
13.665750
13.771500
23.583750
26.907000
27.120750
27.120750
27.332250
QuasiPeak
(dBµV)
--23.36
----27.39
--41.57
27.40
--------46.86
-----
Average
(dBµV)
Limit
(dBµV)
23.31
--24.65
22.30
--41.43
----22.26
24.43
27.86
29.66
--46.55
29.58
52.91
59.23
50.00
50.00
60.00
50.00
60.00
60.00
50.00
50.00
50.00
50.00
60.00
50.00
50.00
Margin
(dB)
29.61
35.87
25.35
27.70
32.61
8.57
18.43
32.60
27.74
25.57
22.14
20.34
13.14
3.45
20.42
Line
PE
L1
L1
L1
L1
L1
L1
L1
L1
L1
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
FLO
FLO
FLO
FLO
Remark: Please see annex for the measurement plots.
The conducted emission found in the tables above corresponds clearly to the fixed transmitter frequency of the
EUT. It was determined that this emission on the AC mains is based on radiated coupling into the test setup.
Therefore, for the assessment of the test result, the fixed transmitter frequency of the EUT is not considered.
The chosen operating mode is selected as representative mode to generate “worst-case” conditions, i.e. high
power consumption.
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 11 of 30
3 .2 Spu r iou s r a dia t e d e m ission s
St a n da r d
FCC Part 15, 10-1-11 Edition Subpart C
Th e t e st w a s pe r for m e d a ccor din g t o: ANSI C63.10–2013
3 .2 .1 Te st D e scr ipt ion
The test set-up was made in accordance to the general provisions of ANSI C63.10 in a
typical installation configuration. The Equipment Under Test (EUT) was set up on a nonconductive table 1.0 x 2.0 m² in the semi-anechoic chamber. The influence of the EUT
support table that is used between 30–1000 MHz was evaluated.
The measurement procedure is implemented into the EMI test software EMC32 from R&S.
Exploratory tests are performed at 3 orthogonal axes to determine the worst-case
orientation of a body-worn or handheld EUT. The final test on all kind of EUTs is also
performed at 3 axes. A pre-check is performed while the EUT is powered from a DC
power source.
1 . M e a su r e m e n t u p t o 3 0 M H z
The Loop antenna HFH2-Z2 is used.
St e p 1 : pre measurement
 Anechoic chamber
 Antenna distance: 3 m
 Detector: Peak-Maxhold
 Frequency range: 0.009 - 0.15 MHz and 0.15 – 30 MHz
 Frequency steps: 0.05 kHz and 2.25 kHz
 IF–Bandwidth: 0.2 kHz and 9 kHz
 Measuring time / Frequency step: 100 ms (FFT-based)
Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the
relevant emissions for the final measurement are identified.
St e p 2 : final measurement
For the relevant emissions determined in step 1, an additional measurement with the
following settings will be performed. Intention of this step is to find the maximum
emission level.
 Open area test side
 Antenna distance: according to the Standard
 Detector: Quasi-Peak
 Frequency range: 0.009 – 30 MHz
 Frequency steps: measurement at frequencies detected in step 1
 IF–Bandwidth: 0.2 - 10 kHz
 Measuring time / Frequency step: 1 s
2 . M e a su r e m e n t a bove 3 0 M H z a n d u p t o 1 GH z
St e p 1 : Preliminary scan
This is a preliminary test to identify the highest amplitudes relative to the limit.
Settings for step 1:
- Antenna distance: 3 m
- Detector: Peak-Maxhold / Quasipeak (FFT-based)
- Frequency range: 30 – 1000 MHz
- Frequency steps: 30 kHz
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 12 of 30
- IF–Bandwidth: 120 kHz
- Measuring time / Frequency step: 100 ms
- Turntable angle range: –180° to 90°
- Turntable step size: 90°
- Height variation range: 1 – 3 m
- Height variation step size: 2 m
- Polarisation: Horizontal + Vertical
Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the
relevant emissions for the final measurement are identified.
St e p 2 : Adjustment measurement
In this step the accuracy of the turntable azimuth and antenna height will be improved.
This is necessary to find out the maximum value of every frequency.
For each frequency, which was determined the turntable azimuth and antenna height will
be adjusted. The turntable azimuth will slowly vary by ± 45° around this value. During
this action, the value of emission is continuously measured. The turntable azimuth at the
highest emission will be recorded and adjusted. In this position, the antenna height will
also slowly vary by ± 100 cm around the antenna height determined. During this action,
the value of emission is also continuously measured. The antenna height of the highest
emission will also be recorded and adjusted.
- Detector: Peak – Maxhold
- Measured frequencies: in step 1 determined frequencies
- IF – Bandwidth: 120 kHz
- Measuring time: 100 ms
- Turntable angle range: ± 45 ° around the determined value
- Height variation range: ± 100 cm around the determined value
- Antenna Polarisation: max. value determined in step 1
St e p 3 : Final measurement with QP detector
With the settings determined in step 3, the final measurement will be performed:
EMI receiver settings for step 4:
- Detector: Quasi-Peak (< 1 GHz)
- Measured frequencies: in step 1 determined frequencies
- IF – Bandwidth: 120 kHz
- Measuring time: 1 s
After the measurement a plot will be generated this contains a diagram with the results
of the preliminary scan and a chart with the frequencies and values of the results of the
final measurement.
3 . M e a sur e m e nt a bove 1 GH z
The following modifications apply to the measurement procedure for the frequency range
above 1 GHz:
St e p 1 :
The Equipment Under Test (EUT) was set up on a non-conductive support (tilt device) at
1.5 m height in the fully-anechoic chamber.
All steps were performed with one height of the receiving antenna only.
The EUT is turned during the preliminary measurement across the elevation axis, with a
step size of 90 °.
The turn table step size (azimuth angle) for the preliminary measurement is 45 °.
St e p 2 :
Due to the fact, that in this frequency range the test is performed in a fully anechoic
room, the height scan of the receiving antenna instep 2 is omitted. Instead of this, a
maximum search with a step size ± 45° for the elevation axis is performed.
The turn table azimuth will slowly vary by ± 22.5°.
The elevation angle will slowly vary by ± 45°
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 13 of 30
EMI receiver settings (for all steps):
- Detector: Peak, Average
- IF Bandwidth = 1 MHz
St e p 3 :
Spectrum analyser settings for step 3:
- Detector: Peak / Average
- Measured frequencies: in step 1 determined frequencies
- IF – Bandwidth: 1 MHz
- Measuring time: 1 s
3 .2 .2 Te st Re qu ir e m e n t s / Lim it s
FCC Part 15, Subpart C, §15.247 (d)
... In addition, radiated emissions which fall in the restricted bands, as defined in Section
15.205(a), must also comply with the radiated emission limits specified in Section
15.209(a) (see Section 15.205(c)).
FCC Part 15, Subpart C, §15.209, Radiated Emission Limits
Frequency in MHz
Limit (µV/m)
0.009 – 0.49
0.49 – 1.705
1.705 – 30
2400/F(kHz)@300m
24000/F(kHz)@30m
30@30m
Measurement
distance (m)
Limits (dBµV/m)
(48.5 – 13.8)@300m
(33.8 – 23.0)@30m
29.5@30m
The measured values are corrected with an inverse linear distance extrapolation factor
(40 dB/decade) according FCC 15.31 (2).
Frequency in MHz
Limit (µV/m)
30 – 88
88 – 216
216 – 960
960 - 26000
26000 - 40000
100@3m
150@3m
200@3m
500@3m
500@3m
Measurement
distance (m)
Limits (dBµV/m)
40.0@3m
43.5@3m
46.0@3m
54.0@3m
54.0@3m
The measured values above 26 GHz are corrected with an inverse linear distance
extrapolation factor (20 dB/decade).
§15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using
instrumentation with a peak detector function, corresponding to 20 dB above the
maximum permitted average limit....
Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m)
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 14 of 30
3 .2 .3 Te st Pr ot ocol
Temperature:
Air Pressure:
Humidity:
23 °C
1009 hPa
38 %
3 .2 .3 .1 M e a sur e m e nt up t o 3 0 M H z
Op. M ode
op-mode 1
Pola r isa t ion
0°
90°
Se t up
Setup_01
Fr e que n cy
MHz
–
–
Por t
Enclosure
Cor r e ct e d va lue
dBµ V/ m
QP
Pe a k
AV
Lim it
dBµ V/
QP
–
–
–
–
–
–
–
–
Lim it
dBµ V/
Pe a k
Lim it
dBµ V/
AV
D e lt a t o
lim it
dB
QP/ Pe a k
D e lt a t o
lim it
dB
AV
–
–
–
–
–
–
–
–
Remark: No spurious emissions in the range 20 dB below the limit found therefore step 2 was not
performed. Please refer to the plot in the annex.
3 .2 .3 .2 M e a sur e m e n t a bove 3 0 M H z
Op. M ode
op-mode 1
Pola r isa t ion
Horizontal
Horizontal
Se t up
Setup_01
Fr e que n cy
MHz
352.56
352.56
Por t
Enclosure
Cor r e ct e d va lue
dBµ V/ m
QP
Pe a k
AV
Lim it
dBµ V/
QP
38.4
35.8
–
–
–
–
46.0
46.0
Lim it
dBµ V/
Pe a k
Lim it
dBµ V/
AV
D e lt a t o
lim it
dB
QP/ Pe a k
D e lt a t o
lim it
dB
AV
–
–
–
–
7.62
10.2
–
–
Remark: No further spurious emissions in the range 20 dB below the limit found.
3 .2 .4 Te st r e su lt : Spu r iou s r a dia t e d e m ission s
FCC Pa r t 1 5 , Su bpa r t C
Op. M ode
op-mode 1
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Re su lt
passed
Page 15 of 30
3 .3
Occu pie d ba n dw idt h
St a n da r d
FCC Part 15, 10-1-15 Edition Subpart C
Th e t e st w a s pe r for m e d a ccor din g t o: FCC §15.31
3 .3 .1
Te st D e scr ipt ion
The Equipment Under Test (EUT) was setup in a shielded room to perform the occupied
bandwidth measurements.
The reference level is the level of the highest amplitude signal observed from the
transmitter at either the fundamental frequency or first-order modulation products in all
typical modes of operation, including the unmodulated carrier, even if atypical.
The results recorded were measured with the modulation which produces the worst-case
(widest) occupied bandwidth.
3 .3 .2
Te st Re quir e m e n t s / Lim it s
FCC Part 15, Subpart C, §15.215 (c)
Intentional radiators operating under the alternative provisions to the general emission
limits, as contained in §§ 15.217 through 15.257 and in Subpart E of this part, must be
designed to ensure that the 20 dB bandwidth of the emission, or whatever bandwidth
may otherwise be specified in the specific rule section under which the equipment
operates, is contained within the frequency band designated in the rule section under
which the equipment is operated. …
3 .3 .3
Te st Pr ot ocol
Temperature:
Air Pressure:
Humidity:
22 °C
1013 hPa
45 %
Op. M ode
op-mode 1
Se t up
Setup_02
2 0 dB ba n dw idt h
kHz
432.960
Por t
Enclosure
9 9 % ba n dw idt h
kHz
492.051
Re m a r k s
The 20 dB bandwidth from 13.34322 MHz
to 13.77618 MHz is contained within the
designated frequency band 13.110 MHz to
14.010 MHz.
Remark: Please see annex for the measurement plot.
3 .3 .4 Te st r e su lt : Occu pie d ba ndw idt h
FCC Pa r t 1 5 , Su bpa r t C
Op. M ode
op-mode 1
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Re su lt
passed
Page 16 of 30
3 .4
Spe ct r u m m a sk
St a n da r d
FCC Part 15, 10-1-15 Edition Subpart C
Th e t e st w a s pe r for m e d a ccor din g t o: FCC §15.225
3 .4 .1
Te st D e scr ipt ion
The test set-up was made in accordance to the general provisions of ANSI C 63.10–2013.
The Equipment Under Test (EUT) was set up on a non-conductive table in the anechoic
chamber.
The radiated emissions measurements were made in a typical installation configuration.
The measurement procedure is implemented into the EMI test software ES-K1 from R&S.
The Loop antenna HFH2-Z2 is used.
Anechoic chamber
Antenna distance: 3 m
Detector: Peak-Maxhold
Frequency range: 13.06 – 14.06 MHz
Frequency steps: 5 kHz
IF–Bandwidth:10 kHz
Measuring time / Frequency step: 100 ms
3 .4 .2
Te st Lim it s
FCC Part 15, Subpart C, §15.225 (a-d), and §15.209, corrected by the means of the
extrapolation of §15.31 due to the reduced measuring distance from 30 m to 3 m with an
inverse linear distance extrapolation factor (40 dB/decade).
3 .4 .3 Te st Pr ot ocol
Temperature:
Air Pressure:
Humidity:
22 °C
1013 hPa
40 %
Op. M ode
op-mode 1
Se t up
Setup_01
M a x im u m va lu e
dBµ V/ m @ 3 0 m
15.56
Por t
Enclosure
Lim it
dBµ V/ m @ 3 0 m
84.0
Re m a r k s
measuring distance 3 m
Remark: Please see annex for the measurement plot.
3 .4 .4 Te st r e su lt : Spe ct r u m m a sk
FCC Pa r t 1 5 , Su bpa r t C
Op. M ode
op-mode 1
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Re su lt
passed
Page 17 of 30
3 .5
Fr e qu e n cy t ole r a n ce
St a n da r d
FCC Part 15, 10-1-15 Edition Subpart C
Th e t e st w a s pe r for m e d a ccor din g t o: FCC §15.225
3 .5 .1
Te st D e scr ipt ion
The Equipment Under Test (EUT) is placed in a temperature chamber.
The frequency drift during temperature and voltage variation is measured by the means
of a spectrum analyzer with frequency counter function.
The temperature was varied from –40 °C to +85 °C. At +20 °C the extreme power
supply voltages of 3.0 V and 3.6 V are applied. After reaching each target temperature
and waiting sufficient time allowing the temperature to stabilize, one measurement is
performed immediately after powering on the EUT, and three further measurements are
performed after 2, 5 and 10 minutes continuous operation of EUT.
3 .5 .2
Te st Lim it s
FCC Part 15, Subpart C, §15.225 (e): The frequency tolerance of the carrier signal shall
be maintained within ±0.01% of the operating frequency over a temperature variation of
-20 degrees to +50 degrees C at normal supply voltage, and for a variation in the
primary supply voltage from 85% to 115% of the rated supply voltage at a temperature
of 20 degrees C.
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 18 of 30
3 .5 .3
Te st Pr ot ocol
Temperature:
Air Pressure:
Humidity:
Op. M ode
op-mode 2
Te m pe r a t u r e
/ °C
50
50
50
50
40
40
40
40
30
30
30
30
20
20
20
20
20
20
20
20
20
20
20
20
10
10
10
10
-10
-10
-10
-10
-20
-20
-20
-20
-40°C to +85°C
1009 hPa
38 %
Se t up
Setup_01
Volt a ge
/ V
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.60
3.60
3.60
3.60
3.30
3.30
3.30
3.30
3.00
3.00
3.00
3.00
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
3.30
Por t
Enclosure
Tim e
/ m in.
10
10
10
10
10
10
10
10
10
10
Fr e qu e n cy
/ MHz
13.559882
13.559880
13.559879
13.559878
13.559924
13.559920
13.559919
13.559918
13.559997
13.559976
13.559974
13.559972
13.560031
13.560030
13.560029
13.560029
13.560032
13.560031
13.560029
13.560030
13.560031
13.560030
13.560029
13.560030
13.560086
13.560085
13.560084
13.560084
13.560130
13.560127
13.560127
13.560127
13.560153
13.560152
13.560152
13.560152
13.560141
13.560143
13.560144
13.560144
D e lt a
/ Hz
-118
-120
-121
-122
-76
-80
-81
-82
-3
-24
-26
-28
31
30
29
29
32
31
29
30
31
30
29
30
86
85
84
84
130
127
127
127
153
152
152
152
141
143
144
144
Ve r dict
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Continue on the next page
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 19 of 30
Additional measurements to prove the EUT working ability from -40° C to +85° C
Temperature
/ °C
Voltage
/V
Time
/ min.
Frequency
/ MHz
Delta
/ Hz
Verdict
85
85
85
85
80
80
80
80
70
70
70
70
60
60
60
60
-30
-30
-30
-30
-40
-40
-40
-40
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
10
10
10
10
10
10
13.559920
13.559937
13.559945
13.559945
13.559899
13.559904
13.559906
13.559908
13.559862
13.559863
13.559864
13.559866
13.559859
13.559858
13.559858
13.559858
13.560103
13.560106
13.560106
13.560106
13.560029
13.560033
13.560030
13.560031
-80
-63
-55
-55
-101
-96
-94
-92
-138
-137
-136
-134
-141
-142
-142
-142
103
106
106
106
29
33
30
31
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Passed
Remark:
The limit is a delta of max. ±1356 Hz (0.01 %).
3 .5 .4 Te st r e su lt : Fr e qu e n cy t ole r a n ce
FCC Pa r t 1 5 , Su bpa r t C
Op. M ode
op-mode 2
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Re su lt
passed
Page 20 of 30
4
Te st Equ ipm e n t
Ra dia t e d Em ission s
Re f.N o.
Lab to perform radiated emission tests
D e vice N a m e
D e scr ipt ion
M a n u fa ct u r e r
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
1.14
1.15
1.16
1.17
1.18
1.19
Se r ia l N u m be r
Ca libr a t ion
Due
Fully Anechoic
Room
AM 4.0
ESR 7
8.80m x 4.60m x Albatross Projects P26971-647-001-PRB
4.05m (l x w x h)
Antenna mast
Maturo GmbH
AM4.0/180/11920513
EMI Receiver /
Rohde & Schwarz 101424
2016-11-13
Spectrum Analyzer
Anechoic Chamber 10.58 x 6.38 x
Frankonia
none
2017-01-09
6.00 m³
ESIB 26
Spectrum Analyzer Rohde & Schwarz 830482/004
2017-12-08
Tilt device Maturo Antrieb TD1.5Maturo GmbH
TD1.5(Rohacell)
10kg
10kg/024/3790709
AS 620 P
Antenna mast
HD GmbH
620/37
NRV-Z1
Sensor Head A
Rohde & Schwarz 827753/005
2016-05-11
JS4-18002600-32- Broadband
Miteq
849785
5P
Amplifier 18 GHz 26 GHz
HL 562
Ultralog new
Rohde & Schwarz 830547/003
2018-06-30
biconicals
GmbH & Co. KG
Opus10 THI
ThermoHygro
Lufft Mess- und 12482
2017-03-10
(8152.00)
Datalogger 12
Regeltechnik
(Environ)
GmbH
HFH2-Z2
Loop Antenna
Rohde & Schwarz 829324/006
2017-11-27
GmbH & Co. KG
FSW 43
Spectrum Analyzer Rohde & Schwarz 103779
2016-11-17
2017-02-27
Opus10 TPR
ThermoAirpressure Lufft Mess- und 13936
Datalogger 13
Regeltechnik
(8253.00)
(Environ)
GmbH
Chroma 6404
AC Power Source Chroma ATE INC. 64040001304
3160-10
Standard Gain /
EMCO Elektronik 00086675
Pyramidal Horn
GmbH
Antenna 40 GHz
HL 562 Ultralog
Log.-per. Antenna Rohde & Schwarz 100609
2016-03-18
GmbH & Co. KG
HF 907
Double-ridged
Rohde & Schwarz 102444
2018-05-11
horn
GmbH & Co. KG
DE 325
Dreheinheit
HD GmbH
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 21 of 30
2
Ra dio La b
Conducted Radio Test Lab
D e vice N a m e
D e scr ipt ion
Re f.N o.
2.1
A8455-4
2.2
SMB100A
2.3
2.4
VT 4002
SMP03
2.5
FSV30
2.6
SMBV100A
2.7
Voltcraft M-3860M
2.8
2.9
Chroma 6404
Datum, Model: MFS
2.10
WA1515
2.11
FSIQ26
Re f.N o.
4 Way Power
Divider (SMA)
Signal Generator Rohde & Schwarz
9 kHz - 6 GHz
GmbH & Co. KG
Climatic Chamber Vötsch
Signal Generator Rohde & Schwarz
2 GHz - 27 GHz GmbH & Co. KG
1035.5005.03
Signal Analyzer
Rohde & Schwarz
10 Hz - 30 GHz
Vector Signal
Rohde & Schwarz
Generator 9 kHz - GmbH & Co. KG
6 GHz
Digital Multimeter Voltcraft
01 (Multimeter)
AC Power Source Chroma ATE INC.
Datum-Beverly
Rubidium
Frequency
Standard
Broadband Power Weinschel
Divider SMA
Associates
Spectrum
Rohde & Schwarz
Analyzer 7layers, GmbH & Co. KG
Ratingen OIL_RE
R& S TS8 9 9 7
EN300328/301893 Test Lab
D e vice N a m e
D e scr ipt ion
3.1
OSP120
3.2
A8455-4
3.3
Opus10 THI
(8152.00)
3.4
SMB100A
3.5
3.6
VT 4002
FSV30
3.7
SMBV100A
3.8
Voltcraft M-3860M
3.9
1515 / 93459
3.10
Datum, Model: MFS
M a n u fa ct u r e r
M a n u fa ct u r e r
Se r ia l N u m be r
Ca libr a t ion
Due
107695
2017-06-06
58566002150010 2016-03-11
833680/003
2016-10-29
103005
2018-02-10
259291
2016-08-23
IJ096055
64040001304
5489/001
2016-06-25
A855
840061/005
Se r ia l N u m be r
2017-04-02
Ca libr a t ion
Due
2016-08-21
Switching Unit
Rohde & Schwarz 101158
with integrated
GmbH & Co. KG
power meter
4 Way Power
Divider (SMA)
7482
2017-02-27
Lufft Mess- und
ThermoHygro
Regeltechnik
Datalogger 03
GmbH
(Environ)
Signal Generator Rohde & Schwarz 107695
2017-06-06
9 kHz - 6 GHz
GmbH & Co. KG
Climatic Chamber Vötsch
58566002150010 2016-03-11
Signal Analyzer
Rohde & Schwarz 103005
2018-02-10
10 Hz - 30 GHz
Vector Signal
Rohde & Schwarz 259291
2016-08-23
Generator 9 kHz - GmbH & Co. KG
6 GHz
Digital Multimeter Voltcraft
IJ096055
01 (Multimeter)
Broadband Power Weinschel
LN673
Divider SMA
Associates
(Aux)
Datum-Beverly
5489/001
2016-06-25
Rubidium
Frequency
Standard
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 22 of 30
5
Ph ot o Re por t
Photos are included in an external report.
Se t u p D r a w in gs
D r a w in g 1 :
Setup in the Anechoic chamber:
Measurements below 1 GHz: Semi-anechoic, conducting ground plane.
Measurements above 1 GHz: Fully-anechoic, absorbers on all surfaces.
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 23 of 30
7
FCC a nd I C Cor r e la t ion of m e a su r e m e n t r e qu ir e m e n t s
The following tables show the correlation of measurement requirements Radio equipment
operating in the Band 13.110-14.010 MHz from FCC and IC.
Ra dio e qu ipm e n t
M e a sur e m e n t
FCC r e fe r e n ce
I C r e fe r e nce
Conducted emissions on AC
Mains
§ 15.207
RSS-Gen Issue 4: 8.8
Additional provisions to the
general radiated emission
limitations
§ 15.215
RSS-Gen Issue 4: 6.6
Out-of-band emissions
§ 15.225 (d)
RSS Gen Issue 4:
6.13/8.9/8.10;
RSS-210 Issue 8: A2.6
In-band emissions
§ 15.225 (a) / (b) / (c)
RSS-210 Issue 8: A2.6
Frequency Stability
§ 15.225 (e)
RSS-210 Issue 8: A2.6
Antenna requirement
§ 15.203 / 15.204
RSS-Gen Issue 4: 8.3
Receiver spurious emissions
–
RSS-210 Issue 8: 2.3;
RSS Gen Issue 4: 5/7 *)
Handling of active and
passive tag devices of RFID
application
§ 15.225 (f)
RSS Gen Issue 4: 8.7
*) Receivers are exempted from certification besides if operating in stand-alone mode in
the frequency range 30–960 MHz or if these are scanner receivers.
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 24 of 30
8
An n e x m e a su r e m e n t plot s
8 .1 Ra dia t e d e m ission s
8 .1 .1 Ra dia t e d e m ission s ( f < 3 0 M H z)
70
60
13.560000 MHz
14.665 dBµV/m
Level in dBµV/m
40
20
FCC_15.209_Peak@300m_9kHz-490kHz
FCC_15.209_QP@300m@30m_90kHz-30MHz
FCC_15.209_AV@300m_9kHz-490kHz
27.120000 MHz
-0.848 dBµV/m
-20
-40
-60
9k
20
30
50
100k
200 300
500
1M
2M 3M
5M
10M
20 30M
Frequency in Hz
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 25 of 30
8 .1 .2 Ra dia t e d e m ission s ( f > 3 0 M H z)
EUT in a vertical position
60
FCC_15.209_30M-1GHz@3m
50
Level in dBµV/m
40
30
20
10
30M
50
60
80
100M
200
300
400
500
800
1G
Frequency in Hz
EUT in a horizontal position
60
FCC_15.209_30M-1GHz@3m
50
Level in dBµV/m
40
30
20
10
30M
50
60
80
100M
200
300
400
500
800
1G
Frequency in Hz
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 26 of 30
8 .2 AC M a in s con du ct e d
Measurement performed with a real antenna.
80
70
Limit_15_207_QP
Level in dBµV
60
Limit_15_207_AV
50
40
30
20
10
150k
300 400 500
800 1M
2M
3M 4M 5M 6
8 10M
20M
30M
Frequency in Hz
Measurement performed with a real antenna (zoomed).
70.2
Limit_15_207_QP
60
Limit_15_207_AV
Level in dBµV
50
40
30
20
10
0.7
8.823
10
11
12
13
14
15
16
17
18 18.608
Frequency in MHz
Note: Measured levels above the limit are from modulated carrier signal.
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 27 of 30
Measurement performed with a 50 Ω dummy antenna
80
70
Limit_15_207_QP
Level in dBµV
60
Limit_15_207_AV
50
40
30
20
10
150k
300 400 500
800 1M
2M
3M 4M 5M 6
8 10M
20M
30M
Frequency in Hz
Fina l Re sult
Frequency QuasiPeak Average Limit Margin
(MHz)
(dBµV)
(dBµV) (dBµV)
(dB)
0.217500
0.339000
13.348500
13.454250
13.454250
13.560000
13.560000
13.665750
13.665750
13.771500
23.583750
26.907000
27.120750
27.120750
27.332250
--23.36
----27.39
--41.57
27.40
--------46.86
-----
23.31
--24.65
22.30
--41.43
----22.26
24.43
27.86
29.66
--46.55
29.58
52.91
59.23
50.00
50.00
60.00
50.00
60.00
60.00
50.00
50.00
50.00
50.00
60.00
50.00
50.00
29.61
35.87
25.35
27.70
32.61
8.57
18.43
32.60
27.74
25.57
22.14
20.34
13.14
3.45
20.42
Meas. Time Bandwidth Line
(ms)
(kHz)
1000.0
1000.0
1000.0
1000.0
1000.0
1000.0
1000.0
1000.0
1000.0
1000.0
1000.0
1000.0
1000.0
1000.0
1000.0
9.000
9.000
9.000
9.000
9.000
9.000
9.000
9.000
9.000
9.000
9.000
9.000
9.000
9.000
9.000
L1
L1
L1
L1
L1
L1
L1
L1
L1
Hardware Setup:
Measurement Type:
Frequency Range:
Graphics Level Range:
EMI_Conducted_EN_FCC_ESH3-Z5
2 Line LISN
150 kHz - 30 MHz
0 dBµV - 80 dBµV
Preview Measurements:
Scan Test Template:
FCC_Part207_Pre_ESH3-Z5
Final Measurements:
Template for Single Meas.:
FCC_Part207_Final_ESH3-Z5
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
PE
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
FLO
FLO
FLO
FLO
Corr.
(dB)
10.1
10.1
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
11.1
11.2
11.2
11.2
11.2
Comment
16:54:48 - 06/01/2016
16:54:13 - 06/01/2016
16:54:53 - 06/01/2016
16:54:58 - 06/01/2016
16:54:19 - 06/01/2016
16:55:02 - 06/01/2016
16:54:24 - 06/01/2016
16:54:30 - 06/01/2016
16:55:07 - 06/01/2016
16:55:11 - 06/01/2016
16:55:16 - 06/01/2016
16:54:35 - 06/01/2016
16:54:07 - 06/01/2016
16:54:39 - 06/01/2016
16:54:44 - 06/01/2016
Page 28 of 30
8 .3 Occu pie d ba n dw idt h
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 29 of 30
8 .4 Spe ct r u m m a sk
90
80
70
Level in dBµV/m
60
50
40
FCC_15.225_TX-Mask@30m_13-56MHz
30
20
10
-10
13
13.1
13.2
13.3
13.4
13.5
13.6
13.7
13.8
13.9
14
14.1
Frequency in MHz
Final_Result
Frequency MaxPeak QuasiPeak Limit Margin
(MHz)
(dBµV/m) (dBµV/m) (dBµV (dB)
/m)
13.560000
--13.76 84.00
70.24
13.560000
15.56
--- 84.00
68.44
Meas. Bandwidth Height Pol Azimuth Corr.
Comment
Time
(kHz)
(cm)
(deg)
(dB)
(ms)
1000.0
10.000 100.0 H
53.0 -19.9 10:39:14 - 05/01/2016
1000.0
10.000 100.0 H
53.0 -19.9 10:39:14 - 05/01/2016
Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1
Page 30 of 30
Download: EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Mirror Download [FCC.gov]EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Test Report MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx u-blox AG
Document ID3128575
Application ID74N2QWRNEQ6JqX4YoMVjNw==
Document DescriptionMDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_SIGNED
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize67.11kB (838919 bits)
Date Submitted2016-09-09 00:00:00
Date Available2016-09-09 00:00:00
Creation Date2017-12-14 05:29:58
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-12-14 05:29:58
Document TitleMDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_finalx
Document CreatorPScript5.dll Version 5.2.2
Document Author: Richwol

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Fill forms, Print high-res
Author                          : Richwol
Create Date                     : 2016:04:01 17:54:29+02:00
Modify Date                     : 2016:04:01 18:19:41+02:00
Signing Date                    : 2016:04:01 18:15:47+02:00
Signing Authority               : DOBRIN TODOROV DOBRINOV
Modification Permissions        : Fill forms, Create page templates, Sign
Form Fields                     : Signature1
Field Permissions               : Disallow changes to specified form fields
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2016:04:01 18:19:41+02:00
Format                          : application/pdf
Title                           : Microsoft Word - MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_final.docx
Creator                         : Richwol
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:02aaaed3-b6b1-4e5c-a5bf-9af84b16edda
Instance ID                     : uuid:171332e4-29af-4d6a-993c-325807d7da3f
Has XFA                         : No
Page Count                      : 30