Spartan Trainer Test Report - SZEM160900779702 Suunto Oy

Suunto Oy Spartan Trainer

See More Details For FCC ID: RYP24601
Purchase on Amazon: Spartan Trainer
Download: Spartan Trainer Test Report - SZEM160900779702 Suunto Oy
Document DescriptionFCC Test Report
Document TypeTest Report
Document TitleMicrosoft Word - SZEM160900779702.doc

Document

Trouble Loading? Try Spartan Trainer Test Report - SZEM160900779702 Suunto Oy Downloading this document. Zoom In and Out With ⌘ / Ctrl key and plus [+] or minus [-]
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
No. 1 Workshop, M-10, Middle section, Science & Technology Park,
Shenzhen, Guangdong, China 518057
Telephone: +86 (0) 755 2601 2053
Fax: +86 (0) 755 2671 0594
Email: [email protected]s.com
Report No.: SZEM160900779702
Page: 1 of 47
Authorized Signature:
Jack Zhang
EMC Laboratory Manager
The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report.
If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new
system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS
International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by
SGS International Electrical Approvals in writing.
The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of
the federal government. All test results in this report can be traceable to National or International Standards.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery
or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
1 Cover page
FCC REPORT
Application No: SZEM1609007797CR
Applicant: Suunto Oy
Manufacturer: Suunto Oy
Factory: IDT Technology Limited
Product Name: Spartan Trainer
Model No.(EUT): OW163
Trade Mark: Suunto
FCC ID: RYP24601
Standards: 47 CFR Part 15, Subpart C (2015)
Date of Receipt: 2016-09-13
Date of Test: 2016-09-14 to 2016-09-20
Date of Issue: 2016-09-21
Test Result: PASS *
* In the configuration tested, the EUT complied with the standards specified above.
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 2 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
2 Version
Revision Record
Version Chapter Date Modifier
Remark
00 2016-09-21 Original
Authorized for issue by:
Tested By
2016-09-20
(Edison Li) /Project Engineer Date
Checked By
2016-09-21
(Eric Fu) /Reviewer Date
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 3 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
3 Test Summary
Test Item Test Requirement Test method Result
Antenna Requirement 47 CFR Part 15, Subpart C Section
15.203/15.247 (c) ANSI C63.10 2013 PASS
AC Power Line
Conducted
Emission
47 CFR Part 15, Subpart C Section
15.207 ANSI C63.10 2013 PASS
Conducted Peak Output
Power
47 CFR Part 15, Subpart C Section
15.247 (b)(3) ANSI C63.10 2013 PASS
6dB Occupied
Bandwidth
47 CFR Part 15, Subpart C Section
15.247 (a)(2) ANSI C63.10 2013 PASS
Power Spectral Density 47 CFR Part 15, Subpart C Section
15.247 (e) ANSI C63.10 2013 PASS
Band-edge for RF
Conducted Emissions
47 CFR Part 15, Subpart C Section
15.247(d) ANSI C63.10 2013 PASS
RF Conducted Spurious
Emissions
47 CFR Part 15, Subpart C Section
15.247(d) ANSI C63.10 2013 PASS
Radiated Spurious
Emissions
47 CFR Part 15, Subpart C Section
15.205/15.209 ANSI C63.10 2013 PASS
Restricted bands around
fundamental frequency
(Radiated Emission)
47 CFR Part 15, Subpart C Section
15.205/15.209 ANSI C63.10 2013 PASS
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 4 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
4 Contents
Page
1 COVER PAGE ......................................................................................................................................................... 1
2 VERSION .................................................................................................................................................................. 2
3 TEST SUMMARY .................................................................................................................................................... 3
4 CONTENTS .............................................................................................................................................................. 4
5 GENERAL INFORMATION ................................................................................................................................... 5
5.1 CLIENT INFORMATION .......................................................................................................................................... 5
5.2 GENERAL DESCRIPTION OF EUT .......................................................................................................................... 5
5.3 TEST ENVIRONMENT ............................................................................................................................................ 7
5.4 DESCRIPTION OF SUPPORT UNITS ......................................................................................................................... 7
5.5 TEST LOCATION ................................................................................................................................................... 7
5.6 TEST FACILITY ..................................................................................................................................................... 8
5.7 DEVIATION FROM STANDARDS ............................................................................................................................. 8
5.8 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................................. 8
5.9 OTHER INFORMATION REQUESTED BY THE CUSTOMER ........................................................................................ 8
5.10 EQUIPMENT LIST .................................................................................................................................................. 9
6 TEST RESULTS AND MEASUREMENT DATA .............................................................................................. 11
6.1 ANTENNA REQUIREMENT ................................................................................................................................... 11
6.2 CONDUCTED EMISSIONS ..................................................................................................................................... 12
6.3 CONDUCTED PEAK OUTPUT POWER ................................................................................................................... 16
6.4 6DB OCCUPY BANDWIDTH ................................................................................................................................. 19
6.5 POWER SPECTRAL DENSITY ............................................................................................................................... 22
6.6 BAND-EDGE FOR RF CONDUCTED EMISSIONS .................................................................................................... 25
6.7 SPURIOUS RF CONDUCTED EMISSIONS .............................................................................................................. 27
6.8 RADIATED SPURIOUS EMISSION ......................................................................................................................... 33
6.8.1 Spurious Emissions ................................................................................................................................ 33
6.9 RESTRICTED BANDS AROUND FUNDAMENTAL FREQUENCY ................................................................................ 40
7 PHOTOGRAPHS - EUT TEST SETUP .............................................................................................................. 46
7.1 CONDUCTED EMISSION ...................................................................................................................................... 46
7.2 RADIATED EMISSION .......................................................................................................................................... 46
7.3 RADIATED SPURIOUS EMISSION ......................................................................................................................... 47
8 PHOTOGRAPHS - EUT CONSTRUCTIONAL DETAILS ............................................................................... 47
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 5 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
5 General Information
5.1 Client Information
Applicant: Suunto Oy
Address of Applicant: Valimotie 7 FI 01510 Vantaa Finland
Manufacturer: Suunto Oy
Address of Manufacturer: Valimotie 7 FI 01510 Vantaa Finland
Factory: IDT Technology Limited
Address of Factory: Block 29-33, Chentian Industrial Estate Xixiang Town, BaoAn Country,
Shenzhen, Guangdong, P.R.China
5.2 General Description of EUT
Product Name: Spartan Trainer
Model No.: OW163
Trade Mark: Suunto
Operation Frequency: 2402MHz to 2480MHz
Bluetooth Version: Bluetooth V4.0 single mode
Modulation Type: GFSK
Number of Channel: 40
Sample Type: Portable production
Antenna Type: Integral
Antenna Gain: -6.92dBi
Power Supply: DC 3.8V, 300mAh rechargeable battery
DC 5V from external power
Cable: USB cable: 93cm unshielded
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 6 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Operation Frequency each of channel
Channel
Frequency Channel
Frequency Channel
Frequency Channel
Frequency
0 2402MHz 10 2422MHz 20 2442MHz 30 2462MHz
1 2404MHz 11 2424MHz 21 2444MHz 31 2464MHz
2 2406MHz 12 2426MHz 22 2446MHz 32 2466MHz
3 2408MHz 13 2428MHz 23 2448MHz 33 2468MHz
4 2410MHz 14 2430MHz 24 2450MHz 34 2470MHz
5 2412MHz 15 2432MHz 25 2452MHz 35 2472MHz
6 2414MHz 16 2434MHz 26 2454MHz 36 2474MHz
7 2416MHz 17 2436MHz 27 2456MHz 37 2476MHz
8 2418MHz 18 2438MHz 28 2458MHz 38 2478MHz
9 2420MHz 19 2440MHz 29 2460MHz 39 2480MHz
Note:
In section 15.31(m), regards to the operating frequency range over 10 MHz, the lowest frequency, the middle
frequency, and the highest frequency of channel were selected to perform the test, and the selected channel
see below:
Channel Frequency
The lowest channel (CH0) 2402MHz
The middle channel (CH19) 2440MHz
The highest channel (CH39) 2480MHz
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 7 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
5.3 Test Environment
Operating Environment:
Temperature: 25.0 °C
Humidity: 55 % RH
Atmospheric Pressure: 1010mbar
5.4 Description of Support Units
The EUT has been tested with associated equipment below.
Description
Manufacturer
Model No.
Adapter Apple A1357 W010A051
5.5 Test Location
All tests were performed at:
SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch
No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China.
518057.
Tel: +86 755 2601 2053 Fax: +86 755 2671 0594
No tests were sub-contracted.
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 8 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
5.6 Test Facility
The test facility is recognized, certified, or accredited by the following organizations:
• CNAS (No. CNAS L2929)
CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC
Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration
Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration
Laboratories) for the competence in the field of testing.
• A2LA (Certificate No. 3816.01)
SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the
American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01.
• VCCI
The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services
Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with
Registration No.: G-823, R-4188, T-1153 and C-2383 respectively.
• FCC – Registration No.: 556682
SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been registered
and fully described in a report filed with the (FCC) Federal Communications Commission. The
acceptance letter from the FCC is maintained in our files. Registration No.: 556682.
• Industry Canada (IC)
Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards
Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and
Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1,
4620C-2, 4620C-3.
5.7 Deviation from Standards
None.
5.8 Abnormalities from Standard Conditions
None.
5.9 Other Information Requested by the Customer
None.
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 9 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
5.10 Equipment List
Conducted Emission
Item
Test Equipment
Manufacturer Model No.
Inventory
No.
Cal. date
(yyyy-mm-dd)
Cal.Due date
(yyyy-mm-dd)
1 Shielding Room ZhongYu Electron
GB-88 SEM001-06
2016-05-13
2017-05-13
2 LISN Rohde & Schwarz
ENV216
SEM007-01
2015-10-09
2016-10-09
3 LISN ETS-LINDGREN
3816/2 SEM007-02
2016-04-25
2017-04-25
4 8 Line ISN
Fischer Custom
Communications
Inc.
FCC-
TLISN-T8-
02
EMC0120
2015-09-28
2016-09-28
5 4 Line ISN
Fischer Custom
Communications
Inc.
FCC-
TLISN-T4-
02
EMC0121
2015-09-28
2016-09-28
6 2 Line ISN
Fischer Custom
Communications
Inc.
FCC-
TLISN-T2-
02
EMC0122
2015-09-28
2016-09-28
7 EMI Test Receiver
Rohde & Schwarz
ESCI SEM004-02
2016-04-25
2017-04-25
8 DC Power Supply
Zhao Xin RXN-305D
SEM011-02
2015-10-09
2016-10-09
RE in Chamber
Item
Test Equipment Manufacturer Model No.
Inventory
No.
Cal. date
(yyyy-mm-dd)
Cal.Due date
(yyyy-mm-dd)
1 3m Semi-Anechoic
Chamber AUDIX N/A SEM001-02
2016-05-13
2017-05-13
2 EMI Test Receiver
Rohde & Schwarz
ESIB26 SEM004-04
2016-04-25
2017-04-25
3 BiConiLog Antenna
(26-3000MHz) ETS-Lindgren 3142C SEM003-02
2014-11-15
2017-11-15
4 Amplifier
(0.1-1300MHz) HP 8447D SEM005-02
2015-10-09
2016-10-09
5 Horn Antenna
(1-18GHz) Rohde & Schwarz
HF907 SEM003-07
2015-06-14
2018-06-14
6 Horn Antenna
(18-26GHz) ETS-Lindgren 3160 SEM003-12
2014-11-24
2017-11-24
7
Horn
Antenna(26GHz-
40GHz)
A.H.Systems, inc.
SAS-573
SEM003-13
2015-02-12
2018-02-12
8 Low Noise Amplifier
Black Diamond
Series
BDLNA-
0118-
352810
SEM005-05
2015-10-09
2016-10-09
9 Band filter Amindeon Asi 3314
SEM023-01
N/A N/A
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 10 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
RF connected test
Item
Test Equipment Manufacturer Model No.
Inventory
No.
Cal. date
(yyyy-mm-dd)
Cal.Due date
(yyyy-mm-dd)
1 Temperature
Chamber
GuangZhou
GongWen GDJW-100
SEM002-02
2016-07-18
2017-07-18
2 DC Power Supply
ZhaoXin RXN-305D
SEM011-02
2015-10-09
2016-10-09
3 Spectrum Analyzer
Rohde & Schwarz
FSP SEM004-06
2015-10-17
2016-10-17
4 Barometer ChangChun DYM3 SEM002-01
2016-04-25
2017-04-25
5 Signal Generator
Rohde & Schwarz
SML03 SEM006-02
2016-04-25
2017-04-25
6 Band filter Amindeon Asi 3314
SEM023-01
N/A N/A
7 Power Meter Rohde & Schwarz
NRVS SEM014-02
2015-10-09
2016-10-09
8 NOISE
GENERATOR
Beijin Daming
Jidian DM1660 EMC0047
2015-10-24
2016-10-24
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 11 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
6 Test results and Measurement Data
6.1 Antenna Requirement
Standard requirement: 47 CFR Part 15C Section 15.203 /247(c)
15.203 requirement:
An intentional radiator shall be designed to ensure that no antenna other than that furnished by the
responsible party shall be used with the device. The use of a permanently attached antenna or of an
antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit
so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or
electrical connector is prohibited.
15.247(b) (4) requirement:
The conducted output power limit specified in paragraph (b) of this section is based on the use of
antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this
section, if transmitting antennas of directional gain greater than 6 dBi are used, the conducted output
power from the intentional radiator shall be reduced below the stated values in paragraphs (b)(1),
(b)(2), and (b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the
antenna exceeds 6 dBi.
EUT Antenna:
The antenna is integrated on the main PCB and no consideration of replacement. The best case gain
of the antenna is -6.92dBi.
Antenna
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 12 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
6.2 Conducted Emissions
Test Requirement: 47 CFR Part 15C Section 15.207
Test Method: ANSI C63.10: 2013
Test Frequency Range:
150kHz to 30MHz
Limit: Frequency range (MHz) Limit (dBuV)
Quasi-peak Average
0.15-0.5 66 to 56* 56 to 46*
0.5-5 56 46
5-30 60 50
* Decreases with the logarithm of the frequency.
Test Procedure: 1) The mains terminal disturbance voltage test was conducted in a shielded
room.
2) The EUT was connected to AC power source through a LISN 1 (Line
Impedance Stabilization Network) which provides a 50/50µH + 5 linear
impedance. The power cables of all other units of the EUT were
connected to a second LISN 2, which was bonded to the ground reference
plane in the same way as the LISN 1 for the unit being measured. A
multiple socket outlet strip was used to connect multiple power cables to a
single LISN provided the rating of the LISN was not exceeded.
3) The tabletop EUT was placed upon a non-metallic table 0.8m above the
ground reference plane. And for floor-standing arrangement, the EUT was
placed on the horizontal ground reference plane.
4) The test was performed with a vertical ground reference plane. The rear of
the EUT shall be 0.4 m from the vertical ground reference plane. The
vertical ground reference plane was bonded to the horizontal ground
reference plane. The LISN 1 was placed 0.8 m from the boundary of the
unit under test and bonded to a ground reference plane for LISNs
mounted on top of the ground reference plane. This distance was between
the closest points of the LISN 1 and the EUT. All other units of the EUT
and associated equipment was at least 0.8 m from the LISN 2.
5) In order to find the maximum emission, the relative positions of equipment
and all of the interface cables must be changed according to
ANSI C63.10: 2013 on conducted measurement.
Test Setup:
Test Mode: Transmitting with GFSK modulation.
Charge +Transmitting mode.
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 13 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Instruments Used: Refer to section 5.10 for details.
Test Results: Pass
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 14 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Measurement Data
An initial pre-scan was performed on the live and neutral lines with peak detector.
Quasi-Peak and Average measurement were performed at the frequencies with maximized peak emission
were detected.
Live line:
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 15 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Neutral line:
Notes:
1. The following Quasi-Peak and Average measurements were performed on the EUT:
2. Final Test Level =Receiver Reading + LISN Factor + Cable Loss.
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 16 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
6.3 Conducted Peak Output Power
Test Requirement: 47 CFR Part 15C Section 15.247 (b)(1)
Test Method: ANSI C63.10 :2013 Section 11.9.1
Test Setup:
Remark:
Offset the High-Frequency cable loss 1.5dB in the spectrum analyzer.
Limit: 30dBm
Test Mode: Transmitting with GFSK modulation.
Instruments Used: Refer to section 5.10 for details.
Test Results: Pass
Measurement Data
GFSK mode
Test channel Peak Output Power (dBm) Limit (dBm) Result
Lowest 5.33 30.00 Pass
Middle 5.28 30.00 Pass
Highest 5.02 30.00 Pass
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 17 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Test plot as follows:
Test mode: GFSK Test channel: Lowest
A
Ref 10 dBm
Offset 1.5 dB
LVL
Att 40 dB
2.5 MHz/Center 2.402 GHz Span 25 MHz
*
*
RBW 3 MHz
VBW 3 MHz
SWT 5 ms
1 PK
M
AXH
3DB
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1
Marker 1 [T1 ]
5.33 dB
m
2.402000000 GHz
Test mode: GFSK Test channel: Middle
A
Ref 11.5 dBm
Offset 1.5 dB
LVL
Att 40 dB
2.5 MHz/Center 2.44 GHz Span 25 MHz
*
*
RBW 3 MHz
VBW 3 MHz
SWT 5 ms
1 PK
M
AXH
3DB
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1
Marker 1 [T1 ]
5.28 dB
m
2.439725000 GHz
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 18 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Test mode: GFSK Test channel: Highest
A
Ref 10 dBm
Offset 1.5 dB
LVL
Att 40 dB
2.5 MHz/Center 2.48 GHz Span 25 MHz
*
*
RBW 3 MHz
VBW 3 MHz
SWT 5 ms
1 PK
M
AXH
3DB
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1
Marker 1 [T1 ]
5.02 dB
m
2.479900000 GHz
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 19 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
6.4 6dB Occupy Bandwidth
Test Requirement: 47 CFR Part 15C Section 15.247 (a)(2)
Test Method: ANSI C63.10: 2013 Section 11.8
Test Setup:
Limit: 500 kHz
Test Mode: Transmitting with GFSK modulation.
Instruments Used: Refer to section 5.10 for details.
Test Results: Pass
Measurement Data
GFSK mode
Test channel 6dB Occupy Bandwidth (MHz) Limit (kHz) Result
Lowest 0.684 500 Pass
Middle 0.681 500 Pass
Highest 0.696 500 Pass
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 20 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Test plot as follows:
Test mode: GFSK Test channel: Lowest
Ref 10 dBm Att 40 dB
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 100 kHz
VBW 300 kHz
SWT 5 ms
Center 2.402 GHz Span 3 MHz300 kHz/
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1
Marker 1 [T1 ]
-0.56 dB
m
2.401637000 GHz
2
Marker 2 [T1 ]
5.45 dB
m
2.402000000 GHz
3
Delta 3 [T1 ]
-0.40 dB
684.000000000 kHz
Test mode: GFSK Test channel: Middle
Ref 10 dBm Att 40 dB
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 100 kHz
VBW 300 kHz
SWT 5 ms
Center 2.44 GHz Span 3 MHz300 kHz/
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1
Marker 1 [T1 ]
-0.72 dB
m
2.439643000 GHz
2
Marker 2 [T1 ]
5.44 dB
m
2.439997000 GHz
3
Delta 3 [T1 ]
-0.65 dB
681.000000000 kHz
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 21 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Test mode: GFSK Test channel: Highest
Ref 10 dBm Att 40 dB
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 100 kHz
VBW 300 kHz
SWT 5 ms
Center 2.48 GHz Span 3 MHz300 kHz/
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1
Marker 1 [T1 ]
-0.91 dB
m
2.479640000 GHz
2
Marker 2 [T1 ]
5.11 dB
m
2.479991000 GHz
3
Delta 3 [T1 ]
-0.14 dB
696.000000000 kHz
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 22 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
6.5 Power Spectral Density
Test Requirement: 47 CFR Part 15C Section 15.247 (e)
Test Method: ANSI C63.10 :2013 Section 11.10.2
Test Setup:
Limit: 8.00dBm/3kHz
Test Mode: Transmitting with GFSK modulation.
Instruments Used: Refer to section 5.10 for details.
Test Results: Pass
Measurement Data
GFSK mode
Test channel Power Spectral Density (dBm/3kHz)
Limit (dBm/3kHz) Result
Lowest -8.25 8.00 Pass
Middle -9.16 8.00 Pass
Highest -7.84 8.00 Pass
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 23 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Test plot as follows:
Test mode: GFSK Test channel: Lowest
A
Ref 10 dBm
Offset 1.5 dB
LVL
Att 40 dB
150 kHz/Center 2.402 GHz Span 1.5 MHz
*
*
RBW 3 kHz
VBW 10 kHz
SWT 170 ms
1 PK
M
AXH
3DB
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1
Marker 1 [T1 ]
-8.25 dB
m
2.402004500 GHz
Test mode: GFSK Test channel: Middle
A
Ref 10 dBm
Offset 1.5 dB
LVL
Att 40 dB
150 kHz/Center 2.44 GHz Span 1.5 MHz
*
*
RBW 3 kHz
VBW 10 kHz
SWT 170 ms
1 PK
M
AXH
3DB
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1
Marker 1 [T1 ]
-9.16 dB
m
2.440004500 GHz
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 24 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Test mode: GFSK Test channel: Highest
A
Ref 10 dBm
Offset 1.5 dB
LVL
Att 40 dB
150 kHz/Center 2.48 GHz Span 1.5 MHz
*
*
RBW 3 kHz
VBW 10 kHz
SWT 170 ms
1 PK
M
AXH
3DB
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1
Marker 1 [T1 ]
-7.84 dB
m
2.480010500 GHz
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 25 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
6.6 Band-edge for RF Conducted Emissions
Test Requirement: 47 CFR Part 15C Section 15.247 (d)
Test Method: ANSI C63.10: 2013 Section 11.13
Test Setup:
Remark:
Offset the High-Frequency cable loss 1.5dB in the spectrum analyzer.
Limit: In any 100 kHz bandwidth outside the frequency band in which the spread
spectrum intentional radiator is operating, the radio frequency power that is
produced by the intentional radiator shall be at least 20 dB below that in the
100 kHz bandwidth within the band that contains the highest level of the
desired power, based on either an RF conducted or a radiated measurement.
Test Mode: Transmitting with GFSK modulation.
Instruments Used: Refer to section 5.10 for details.
Test Results: Pass
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 26 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Test plot as follows:
Test mode: GFSK Test channel: Lowest
Ref 10 dBm Att 40 dB
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 100 kHz
VBW 300 kHz
SWT 2.5 ms
2.4 MHz/Start 2.38 GHz Stop 2.404 GHz
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1
Marker 1 [T1 ]
-36.42 dB
m
2.399992000 GHz
2
Marker 2 [T1 ]
-36.42 dB
m
2.400000000 GHz
3
Marker 3 [T1 ]
5.65 dB
m
2.402032000 GHz
limit
Test mode: GFSK Test channel: Highest
Ref 10 dBm Att 40 dB
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 100 kHz
VBW 300 kHz
SWT 2.5 ms
2.2 MHz/Start 2.478 GHz Stop 2.5 GHz
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1Marker 1 [T1 ]
5.27 dB
m
2.479980000 GHz
2
Marker 2 [T1 ]
-47.65 dB
m
2.483500000 GHz
3
Marker 3 [T1 ]
-47.65 dB
m
2.483500000 GHz
limit
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 27 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
6.7 Spurious RF Conducted Emissions
Test Requirement: 47 CFR Part 15C Section 15.247 (d)
Test Method: ANSI C63.10: 2013 Section 11.11
Test Setup:
Remark:
Offset the High-Frequency cable loss 1.5dB in the spectrum analyzer.
Limit: In any 100 kHz bandwidth outside the frequency band in which the spread
spectrum intentional radiator is operating, the radio frequency power that is
produced by the intentional radiator shall be at least 20 dB below that in the
100 kHz bandwidth within the band that contains the highest level of the
desired power, based on either an RF conducted or a radiated
measurement.
Test Mode: Transmitting with GFSK modulation.
Instruments Used: Refer to section 5.10 for details.
Test Results: Pass
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 28 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Test plot as follows:
Test mode: GFSK Test channel: Lowest
Ref 11.5 dBm Att 20 dB
*
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 100 kHz
VBW 300 kHz
SWT 40 ms
10 MHz/Start 2.4 GHz Stop 2.5 GHz
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1
Marker 1 [T1 ]
5.31 dB
m
2.402000000 GHz
limit
Ref 11.5 dBm Att 20 dB
*
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 1 MHz
VBW 3 MHz
SWT 200 ms
997 MHz/Start 30 MHz Stop 10 GHz
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1Marker 1 [T1 ]
5.31 dB
m
2.401613750 GHz
2
Marker 2 [T1 ]
-34.04 dB
m
2.441493750 GHz
limit
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 29 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Ref 0 dBm Att 10 dB
*
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 1 MHz
VBW 3 MHz
SWT 300 ms
1.5 GHz/Start 10 GHz Stop 25 GHz
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
1
Marker 1 [T1 ]
-50.36 dB
m
14.929375000 GHz
limit
Test mode: GFSK Test channel: Middle
Ref 11.5 dBm Att 20 dB
*
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 100 kHz
VBW 300 kHz
SWT 40 ms
10 MHz/Start 2.4 GHz Stop 2.5 GHz
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1
Marker 1 [T1 ]
5.32 dB
m
2.439975000 GHz
limit
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 30 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Ref 11.5 dBm Att 20 dB
*
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 1 MHz
VBW 3 MHz
SWT 200 ms
997 MHz/Start 30 MHz Stop 10 GHz
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1Marker 1 [T1 ]
5.27 dB
m
2.440247500 GHz
2
Marker 2 [T1 ]
-42.88 dB
m
7.319316250 GHz
limit
Ref 0 dBm Att 10 dB
*
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 1 MHz
VBW 3 MHz
SWT 300 ms
1.5 GHz/Start 10 GHz Stop 25 GHz
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
1
Marker 1 [T1 ]
-50.16 dB
m
13.939375000 GHz
limit
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 31 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Test mode: GFSK Test channel: Highest
Ref 11.5 dBm Att 20 dB
*
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 100 kHz
VBW 300 kHz
SWT 40 ms
10 MHz/Start 2.4 GHz Stop 2.5 GHz
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1
Marker 1 [T1 ]
4.75 dB
m
2.479987500 GHz
limit
Ref 11.5 dBm Att 20 dB
*
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 1 MHz
VBW 3 MHz
SWT 200 ms
997 MHz/Start 30 MHz Stop 10 GHz
-80
-70
-60
-50
-40
-30
-20
-10
0
10
1Marker 1 [T1 ]
4.96 dB
m
2.480127500 GHz
2
Marker 2 [T1 ]
-32.91 dB
m
2.503806250 GHz
limit
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 32 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Ref 0 dBm Att 10 dB
*
*
*
Offset 1.5 dB
1 PK
V
IEW
A
LVL
3DB
RBW 1 MHz
VBW 3 MHz
SWT 300 ms
1.5 GHz/Start 10 GHz Stop 25 GHz
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
1
Marker 1 [T1 ]
-50.54 dB
m
15.295000000 GHz
limit
Remark:
Use 100kHz RBW to determine the relative limit in the band 2.4GHz to 2.5GHz, and Use 1MHz RBW to
measure spurious emissions in the band 30MHz to 10GHz and 10GHz to 25GHz. The sweep points set to
30001.
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 33 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
6.8 Radiated Spurious Emission
6.8.1 Spurious Emissions
Test Requirement: 47 CFR Part 15C Section 15.209 and 15.205
Test Method: ANSI C63.10 :2013 Section 11.12
Test Site: Measurement Distance: 3m (Semi-Anechoic Chamber) for below 1GHz;
3m (fully Anechoic Chamber) for above 1GHz;
Receiver Setup:
Frequency Detector RBW VBW Remark
0.009MHz-0.090MHz Peak 10kHz 30kHz
Peak
0.009MHz-0.090MHz Average 10kHz 30kHz
Average
0.090MHz-0.110MHz Quasi-peak
10kHz 30kHz
Quasi-peak
0.110MHz-0.490MHz Peak 10kHz 30kHz
Peak
0.110MHz-0.490MHz Average 10kHz 30kHz
Average
0.490MHz -30MHz Quasi-peak
10kHz 30kHz
Quasi-peak
30MHz-1GHz Quasi-peak
100 kHz
300kHz
Quasi-peak
Above 1GHz Peak 1MHz 3MHz Peak
Peak 1MHz 10Hz Average
Limit:
Frequency Field strength
(microvolt/meter)
Limit
(dBuV/m)
Remark Measu
rement
distance (m)
0.009MHz-0.490MHz
2400/F(kHz) - - 300
0.490MHz-1.705MHz
24000/F(kHz)
- - 30
1.705MHz-30MHz 30 - - 30
30MHz-88MHz 100 40.0 Quasi-
peak
3
88MHz-216MHz 150 43.5 Quasi-
peak
3
216MHz-960MHz 200 46.0 Quasi-
peak
3
960MHz-1GHz 500 54.0 Quasi-
peak
3
Above 1GHz 500 54.0 Average
3
Note: 15.35(b), Unless otherwise specified, the limit on peak radio
frequency emissions is 20dB above the maximum permitted average emission
limit applicable to the equipment under test. This peak limit applies to the total
peak emission level radiated by the device.
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 34 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Test Setup:
Figure 1. Below 30MHz Figure 2. 30MHz to 1GHz
Figure 3. Above 1 GHz
Test Procedure: a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8
meters above the ground at a 3 meter semi-anechoic chamber. The
table was rotated 360 degrees to determine the position of the highest
radiation.
b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5
meters above the ground at a 3 meter fully anechoic chamber. The table
was rotated 360 degrees to determine the position of the highest
radiation.
c. The EUT was set 3 meters away from the interference-receiving
antenna, which was mounted on the top of a variable-height antenna
tower.
d. The antenna height is varied from one meter to four meters above the
ground to determine the maximum value of the field strength. Both
horizontal and vertical polarizations of the antenna are set to make the
measurement.
e. For each suspected emission, the EUT was arranged to its worst case
and then the antenna was tuned to heights from 1 meter to 4 meters (for
the test frequency of below 30MHz, the antenna was tuned to heights 1
meter) and the rotatable table was turned from 0 degrees to 360
degrees to find the maximum reading.
f. The test-receiver system was set to Peak Detect Function and Specified
Bandwidth with Maximum Hold Mode.
g. If the emission level of the EUT in peak mode was 10dB lower than the
limit specified, then testing could be stopped and the peak values of the
EUT would be reported. Otherwise the emissions that did not have 10dB
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 35 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
margin would be re-tested one by one using peak, quasi-peak or
average method as specified and then reported in a data sheet.
h. Test the EUT in the lowest channel (2402MHz),the middle channel
(2440MHz),the Highest channel (2480MHz)
i. The radiation measurements are performed in X, Y, Z axis positioning
for Transmitting mode, and found the X axis positioning which it is the
worst case.
j. Repeat above procedures until all frequencies measured was complete.
Exploratory Test
Mode:
Transmitting with GFSK modulation.
a.Charge + Transmitting mode.
b.Transmitting mode
Final Test Mode: Transmitting with GFSK modulation.
Pretest the EUT at Transmitting mode and Charge + Transmitting mode,
found the Charge + Transmitting mode which it is worse case.
For below 1GHz part, through pre-scan, the worst case is the lowest
channel.
Only the worst case is recorded in the report.
Instruments Used: Refer to section 5.10 for details.
Test Results: Pass
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 36 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Radiated Emission below 1GHz
30MHz~1GHz (QP)
Test mode: Charge + Transmitting mode Vertical
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 37 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Test mode: Charge + Transmitting mode Horizontal
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 38 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Transmitter Emission above 1GHz
Test mode: GFSK Test channel: Lowest Remark: Peak
Frequency
(MHz)
Antenna
Factor
(dB/m)
Cable
Loss
(dB)
Preamp
Factor
(dB)
Read
Level
(dBuV)
Level
(dBuV/m)
Limit Line
(dBuV/m)
Over
Limit
(dB)
Polarization
3847.726
33.19
7.76 38.63
46.75
49.07 74.00 -24.93
Vertical
4804.000
34.16
8.87 39.03
44.91
48.91 74.00 -25.09
Vertical
6175.716
34.84
10.33
38.89
45.04
51.32 74.00 -22.68
Vertical
7206.000
36.42
10.68
38.18
44.25
53.17 74.00 -20.83
Vertical
9608.000
37.52
12.50
36.99
39.30
52.33 74.00 -21.67
Vertical
12350.530
38.81
14.27
38.66
38.85
53.27 74.00 -20.73
Vertical
3563.687
32.39
7.65 38.50
45.84
47.38 74.00 -26.62
Horizontal
4804.000
34.16
8.87 39.03
45.69
49.69 74.00 -24.31
Horizontal
5803.188
34.59
10.01
39.02
45.61
51.19 74.00 -22.81
Horizontal
7206.000
36.42
10.68
38.18
44.25
53.17 74.00 -20.83
Horizontal
9608.000
37.52
12.50
36.99
40.03
53.06 74.00 -20.94
Horizontal
12279.260
38.77
14.33
38.59
38.39
52.90 74.00 -21.10
Horizontal
Test mode: GFSK Test channel: Middle Remark: Peak
Frequency
(MHz)
Antenna
Factor
(dB/m)
Cable
Loss
(dB)
Preamp
Factor
(dB)
Read
Level
(dBuV)
Level
(dBuV/m)
Limit Line
(dBuV/m)
Over
Limit
(dB)
Polarization
3792.453
33.04
7.74 38.61
44.99
47.16 74.00 -26.84
Vertical
4880.000
34.29
8.97 39.06
46.55
50.75 74.00 -23.25
Vertical
6069.413
34.76
10.47
38.96
45.46
51.73 74.00 -22.27
Vertical
7320.000
36.37
10.72
38.07
44.09
53.11 74.00 -20.89
Vertical
9760.000
37.55
12.58
36.92
40.39
53.60 74.00 -20.40
Vertical
12297.040
38.78
14.31
38.61
38.47
52.95 74.00 -21.05
Vertical
3949.255
33.47
7.79 38.68
45.50
48.08 74.00 -25.92
Horizontal
4880.000
34.29
8.97 39.06
45.44
49.64 74.00 -24.36
Horizontal
6060.637
34.75
10.48
38.96
45.10
51.37 74.00 -22.63
Horizontal
7320.000
36.37
10.72
38.07
44.24
53.26 74.00 -20.74
Horizontal
9760.000
37.55
12.58
36.92
39.16
52.37 74.00 -21.63
Horizontal
12621.510
38.88
14.50
38.93
38.94
53.39 74.00 -20.61
Horizontal
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 39 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Test mode: GFSK Test channel: Highest Remark: Peak
Frequency
(MHz)
Antenna
Factor
(dB/m)
Cable
Loss
(dB)
Preamp
Factor
(dB)
Read
Level
(dBuV)
Level
(dBuV/m)
Limit Line
(dBuV/m)
Over
Limit
(dB)
Polarization
3960.700
33.50
7.80 38.68
45.25
47.87 74.00 -26.13
Vertical
4960.000
34.43
9.09 39.09
45.27
49.70 74.00 -24.30
Vertical
6069.413
34.76
10.47
38.96
45.00
51.27 74.00 -22.73
Vertical
7440.000
36.32
10.77
37.94
44.21
53.36 74.00 -20.64
Vertical
9920.000
37.58
12.67
36.84
39.33
52.74 74.00 -21.26
Vertical
12458.220
38.88
14.18
38.77
39.12
53.41 74.00 -20.59
Vertical
3836.607
33.16
7.75 38.63
45.48
47.76 74.00 -26.24
Horizontal
4960.000
34.43
9.09 39.09
45.54
49.97 74.00 -24.03
Horizontal
6016.949
34.71
10.54
38.99
45.02
51.28 74.00 -22.72
Horizontal
7440.000
36.32
10.77
37.94
43.81
52.96 74.00 -21.04
Horizontal
9920.000
37.58
12.67
36.84
39.90
53.31 74.00 -20.69
Horizontal
12261.500
38.76
14.34
38.57
38.70
53.23 74.00 -20.77
Horizontal
Remark:
1) The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic
equation with a sample calculation is as follows:
Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor
2) Scan from 9kHz to 25GHz, the disturbance above 13GHz and below 30MHz was very low, and the above
harmonics were the highest point could be found when testing, so only the above harmonics had been
displayed. The amplitude of spurious emissions from the radiator which are attenuated more than 20dB
below the limit need not be reported.
3) As shown in this section, for frequencies above 1GHz, the field strength limits are based on average
limits. However, the peak field strength of any emission shall not exceed the maximum permitted average
limits specified above by more than 20 dB under any condition of modulation. So, only the peak
measurements were shown in the report.
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 40 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
6.9 Restricted bands around fundamental frequency
Test Requirement: 47 CFR Part 15C Section 15.209 and 15.205
Test Method: ANSI C63.10: 2013 Section 11.12
Test Site: Measurement Distance: 3m (fully Anechoic Chamber)
Limit:
Frequency Limit (dBuV/m @3m) Remark
30MHz-88MHz 40.0 Quasi-peak Value
88MHz-216MHz 43.5 Quasi-peak Value
216MHz-960MHz 46.0 Quasi-peak Value
960MHz-1GHz 54.0 Quasi-peak Value
Above 1GHz 54.0 Average Value
74.0 Peak Value
Test Setup:
Figure 1. 30MHz to 1GHz Figure 2. Above 1 GHz
Test Procedure: a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters
above the ground at a 3 meter semi-anechoic chamber. The table was rotated
360 degrees to determine the position of the highest radiation.
b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters
above the ground at a 3 meter fully anechoic chamber. The table was rotated
360 degrees to determine the position of the highest radiation.
c. The EUT was set 3 meters away from the interference-receiving antenna,
which was mounted on the top of a variable-height antenna tower.
d. The antenna height is varied from one meter to four meters above the ground
to determine the maximum value of the field strength. Both horizontal and
vertical polarizations of the antenna are set to make the measurement.
e. For each suspected emission, the EUT was arranged to its worst case and then
the antenna was tuned to heights from 1 meter to 4 meters and the rotatable
table was turned from 0 degrees to 360 degrees to find the maximum reading.
f. The test-receiver system was set to Peak Detect Function and Specified
Bandwidth with Maximum Hold Mode.
g. Place a marker at the end of the restricted band closest to the transmit
frequency to show compliance. Also measure any emissions in the restricted
bands. Save the spectrum analyzer plot. Repeat for each power and
modulation for lowest and highest channel
h. Test the EUT in the lowest channel , the Highest channel
i. The radiation measurements are performed in X, Y, Z axis positioning for
Transmitting mode, and found the X axis positioning which it is the worst case.
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 41 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
j. Repeat above procedures until all frequencies measured was complete.
Exploratory Test
Mode:
Transmitting with GFSK modulation.
a.Charge + Transmitting mode.
b.Transmitting mode.
Final Test Mode:
Transmitting with GFSK modulation.
Pretest the EUT at Transmitting mode and Charge + Transmitting mode, found the
Charge + Transmitting mode which it is worse case.
Only the worst case is recorded in the report.
Instruments
Used:
Refer to section 5.10 for details.
Test Results: Pass
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 42 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Test plot as follows:
Worse case mode:
GFSK Test channel: Lowest Remark: Peak Vertical
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 43 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Worse case mode:
GFSK Test channel: Lowest Remark: Peak Horizontal
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 44 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Worse case mode:
GFSK Test channel: Highest Remark: Peak Vertical
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 45 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Worse case mode:
GFSK Test channel: Highest Remark: Peak Horizontal
Note:
The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic
equation with a sample calculation is as follows:
Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 46 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
7 Photographs - EUT Test Setup
Test model No.: OW163
7.1 Conducted Emission
7.2 Radiated Emission
SGS-CSTC Standards
Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM160900779702
Page: 47 of 47
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
7.3 Radiated Spurious Emission
8 Photographs - EUT Constructional Details
Refer to Appendix A - Photographs of EUT Constructional Details for SZEM1609007797CR.
Download: Spartan Trainer Test Report - SZEM160900779702 Suunto Oy
Mirror Download [FCC.gov]Spartan Trainer Test Report - SZEM160900779702 Suunto Oy
Document ID3178847
Application IDP2YMg6AxG1uBUWO3DHVQEA==
Document DescriptionFCC Test Report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize1670789
Date Submitted2016-10-28 00:00:00
Date Available2016-10-28 00:00:00
Creation Date2016-10-28 14:00:45
Producing SoftwareGPL Ghostscript 8.64
Document Lastmod2016-10-28 06:00:49
Document TitleMicrosoft Word - SZEM160900779702.doc
Document CreatorPScript5.dll Version 5.2.2
Document Author: edison_li

Facebook Twitter Google+ RSS © FCCID.io 2017