OMA60 WiFi Access Point User Manual A60 Quick Start Guide v1.3_1116 Open Mesh, Inc.

Open Mesh, Inc. WiFi Access Point

FCC ID Filing: WT8OMA60
Purchase on Amazon: WiFi Access Point

Trouble Viewing? See the or view the HTML Version or PDF in frame
Page 1 of OMA60 WiFi Access Point User Manual A60 Quick Start Guide v1.3_1116 Open Mesh, Inc.
Page 2 of OMA60 WiFi Access Point User Manual A60 Quick Start Guide v1.3_1116 Open Mesh, Inc.
Page 3 of OMA60 WiFi Access Point User Manual A60 Quick Start Guide v1.3_1116 Open Mesh, Inc.
Page 4 of OMA60 WiFi Access Point User Manual A60 Quick Start Guide v1.3_1116 Open Mesh, Inc.
Page 5 of OMA60 WiFi Access Point User Manual A60 Quick Start Guide v1.3_1116 Open Mesh, Inc.

Ethernet or junction box mount
Mounting
This access point can be mounted to any US or European-style
junction box for secure installations in hotel and resort guest
rooms, dorms, care facilities and more.
This access point can be mounted to any wall or pole.
Attach the universal mounting plate with the smooth side
against the wall to a junction box using the designated screw
holes. Connect the small Ethernet cable (included) to the
female connection in the wall, then pull it through the
mounting plate and plug into Ethernet 1. Connect any passthrough device to Ethernet 2 and position the cable in the
bottom channel of the access point. Next, place the access
point over the mounting plate and slide down until it locks
into place.
To unlock, insert a small, flat screwdriver into the hole on the
side of the access point. Slide the access point until it disengages from the mounting plate.
Note: The pass-through port (Ethernet 2) is data only. No
power is passed through the second port.
We help professionals create powerful, easy-to-use networks that automatically spread Internet
connections throughout hotels, apartments, retail stores, restaurants, small and medium-sized
businesses—and just about anywhere else.
The Open Mesh A Series access points are a modular, plug-and-play professional WiFi solution
that works with CloudTrax, a free cloud-based network controller that can manage
an unlimited number of switches, access points and networks around the world.
openmesh.com
© 2016 Open Mesh, Inc. All Rights Reserved.
#400 5 Centerpointe Drive, Lake Oswego, OR USA 97035
Ò
1.
Attach the universal mounting plate to any wall or pole
using screws or zip ties (not included). The small tabs should
be at the top of the plate so the cable exits through the bottom
of the access point.
Open the slit in the side of the rubber gasket and place the
Ethernet cable through the hole. Plug the cable into Ethernet 1.
Place the rubber gasket into the channel surrounding the ports
on the access point. Place the rear cover on the access point
and snap into place. Finally, place the access point over the
mounting plate and slide down until it locks into place .
To unlock, insert a small, flat screwdriver into the hole on the
side of the access point. Slide the access point until it disengages from the mounting plate.
Ò
2.
openmesh.com/a-mount
openmesh.com/a-ethernet
A60
WiFi Access Point
Quick Start Guide
Cloud management
Physical installation
1. Download the CloudTrax mobile app for iOS or Android,
or sign up at cloudtrax.com. (It
'
s included with this access
point.)
This access point is designed to be installed virtually anywhere
Regardless of how you mount this access
point, keep the following in mind:
2. Follow the prompts to verify your account and create your
first network. If you already have a network, create a new
one by navigating to Network → Create new network.
3. Follow the prompts to add your first access point. If you’re
adding this access point to an existing network:
In the CloudTrax mobile app: select Add Access Point from
the top menu and scan the QR code on the bottom of the
access point.
On cloudtrax.com: navigate to Manage → Access Points →
Add New and enter the MAC address. Use the drop-down
arrow to enter multiple MAC addresses at once or upload a
CSV file.
Repeat this process to add as many access points as
required.
This access point requires 802.3af PoE input. Connect to an
802.3af-compatible PoE switch or PoE injector.
Place the access point in the center of the room and away
from any metallic surfaces.
This access point radiates signal primarily to the front and
sides. This access point will only provide limited coverage
directly behind it.
Do not place heavy objects on the access point.
Install the access point in an area free from strong
electromagnetic sources.
Check the Ethernet cables to ensure they are fully secured
to both the access point and PoE injector or switch.
Do not install this access point in plenum spaces. Use the
ceiling mount instead.
Access point overview
Mounting bracket overview
LED indicator
US single
gang box
Wall or solid ceiling mount
T-rail ceiling mount
Attach the universal mounting plate to any solid surface with
the smooth side against the wall (screws are not included). If
the Ethernet cable is in the wall or ceiling, pull it through the
mounting plate; if the cable is outside the wall or ceiling, place
it in the cable channel. Plug the Ethernet cable into Ethernet 1.
Next, place the access point over the mounting plate and slide
down until it locks into place.
Attach the fixed t-rail clips to the back of the universal mounting plate by pushing the top of the clip through the plate and
securing the bottom of the clip to the mounting peg: use the
narrow peg hole for ⁹/₁₆" t-rails and the wider peg hole for /₁₆"
t-rails. Attach the adjustable t-rail clips to the mounting plate
by pushing the top of the clip through the plate and snapping
the bottom of the clip into the channel. Pull the Ethernet cable
through the center of the mounting plate and plug into Ethernet
1. Next, place the access point over the mounting plate and
slide until it locks into place. Clip the cable channel cover in
place. Finally, attach the access point to the ceiling rail by
placing the fixed clip against the rail and sliding the
adjustable clips until secure.
To unlock, insert a small, flat screwdriver into the hole on the
side of the access point. Slide the access point until it disengages from the mounting plate.
Ethernet port 1, 802.3af PoE Ethernet port 2
US dual
gang box
Ò
openmesh.com/a-wall
Ò
openmesh.com/a-ceiling
¹⁵/ " rails ⁹/ " rails
Support and resources
Visit help.cloudtrax.com for additional resources, video guides
and to contact technical support.
USB 2.0
Reset Button
EU/UK
4. Set your configuration. Once your access point has power
and Internet, CloudTrax will configure the access point and
start reporting status within a few minutes.
Continued on reverse side
請勿列印此頁
Don’t print this page.
6709A2463320
2016/11/16
品牌產品規劃PM
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Non-modification Statement:
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
This device complies with RSS 210 of Industry Canada. This Class B device meets all
the requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
IC Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator and your body.
Déclaration d’exposition à la radiation : Cet équipement respecte les limites d’exposition aux
rayonnements IC définies pour un environnement non contrôlé. Cet équipement doit être installé et
mis en marche à une distance minimale de 20 cm qui sépare l’élément rayonnant de votre corps.
L’émetteur ne doit ni être utilisé avec une autre antenne ou un autre émetteur ni se trouver à leur
proximité.
Download: OMA60 WiFi Access Point User Manual A60 Quick Start Guide v1.3_1116 Open Mesh, Inc.
Mirror Download [FCC.gov]OMA60 WiFi Access Point User Manual A60 Quick Start Guide v1.3_1116 Open Mesh, Inc.
Document ID3246040
Application IDBXJ+rTIizNE946pqmjPHEw==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize154.39kB (1929819 bits)
Date Submitted2017-01-04 00:00:00
Date Available2017-01-10 00:00:00
Creation Date2016-11-16 14:32:31
Producing SoftwareAdobe PDF library 9.00
Document Lastmod2016-12-30 14:32:51
Document TitleA60 Quick Start Guide v1.3_1116
Document CreatorAdobe Illustrator CS4
Document Author: deliaf

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Create Date                     : 2016:11:16 14:32:31+08:00
GTS PDFX Version                : PDF/X-4
Modify Date                     : 2016:12:30 14:32:51+08:00
Trapped                         : False
Author                          : deliaf
XMP Toolkit                     : 3.1-701
Producer                        : Adobe PDF library 9.00
Creator Tool                    : Adobe Illustrator CS4
Title                           : A60 Quick Start Guide v1.3_1116
Creator                         : deliaf
Page Count                      : 5
For                             : Charles Chang,
Bounding Box                    : 0 0 1828 462
Container Version               : 11
Creator Version                 : 21
Image Height                    : 462
Image Width                     : 1828
Image Size                      : 1828x462
Megapixels                      : 0.845

Facebook Twitter Google+ RSS © FCCID.io 2017