16420NEX Customizable smart band Test Report SZ16110064W02_bt4.0 fccx Mighty Cast, Inc

Mighty Cast, Inc Customizable smart band

FCC ID Filing: 2AKN3-16420NEX
Purchase on Amazon: Customizable smart band

Trouble Viewing? See the or view the HTML Version or PDF in frame
Page 1 of 16420NEX Customizable smart band Test Report SZ16110064W02_bt4.0 fccx Mighty Cast, Inc

REPORT No.: SZ16110064W02
DIRECTORY
TEST REPORT DECLARATION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙4
1.
TECHNICAL INFORMATION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙5
1.1 APPLICANT INFORMATION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙5
1.2 EQUIPMENT UNDER TEST (EUT) DESCRIPTION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙5
1.2.1 IDENTIFICATION OF ALL USED EUTS ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙5
1.3 TEST STANDARDS AND RESULTS ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙6
1.3.1 TEST ENVIRONMENT CONDITIONS ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙6
2.
47 CFR PART 15C REQUIREMENTS∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙7
2.1
2.1.1
2.1.2
2.2
2.2.1
2.2.2
2.2.3
2.2.4
2.3
2.3.1
2.3.2
2.3.3
2.3.4
2.4
2.4.1
2.4.2
2.4.3
2.5
2.5.1
2.5.2
2.5.3
2.5.4
2.6
ANTENNA REQUIREMENT ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙7
APPLICABLE STANDARD ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙7
RESULT: COMPLIANT ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙7
PEAK OUTPUT POWER∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙7
REQUIREMENT ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙7
TEST DESCRIPTION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙7
TEST PROCEDURE ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙7
TEST RESULT∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙8
6DB BANDWIDTH ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 10
REQUIREMENT ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 10
TEST DESCRIPTION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 10
TEST PROCEDURE ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 10
TEST RESULT∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 11
CONDUCTED SPURIOUS EMISSIONS AND BAND EDGE ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 13
REQUIREMENT ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 13
TEST DESCRIPTION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 13
TEST RESULT∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 13
POWER SPECTRAL DENSITY (PSD) ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙17
REQUIREMENT ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 17
TEST DESCRIPTION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 17
TEST PROCEDURE ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 17
TEST RESULT∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 17
RESTRICTED FREQUENCY BANDS ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙20
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 2 0f 36
REPORT No.: SZ16110064W02
2.6.1 REQUIREMENT ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 20
2.6.2 TEST DESCRIPTION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 20
2.6.3 TEST RESULT∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 21
2.7 CONDUCTED EMISSION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙24
2.7.1 REQUIREMENT ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 24
2.7.2 TEST DESCRIPTION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 24
2.7.3 TEST RESULT∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 25
2.8 RADIATED EMISSION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙27
2.8.1 REQUIREMENT ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 27
2.8.2 TEST DESCRIPTION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 28
2.8.3 TEST RESULT∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 30
ANNEX A GENERAL INFORMATION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙34
Change History
Issue
Date
Reason for change
1.0
2016-12-19
First edition
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 3 0f 36
REPORT No.: SZ16110064W02
1. TECHNICAL INFORMATION
Note: Provide by applicant.
1.1
Applicant Information
Company:
Mighty Cast, Inc
Address:
1470 Peel Street, Tower B, Suite 745 Montreal, QC H3A 1T1 CANADA
1.2
Equipment under Test (EUT) Description
Brand Name:
The Nex Band
Trade Name:
The Nex Band
Model Name:
M16-420
Frequency Range:
The frequency range used is 2402MHz - 2480MHz (40 channels, at
intervals of 2MHz);
Modulation Type:
GFSK
Bluetooth Version:
Bluetooth 4.0 BLE
Antenna Type:
Metal plate
Antenna Gain:
0 dBi
NOTE:
The EUT is a Customizable smart band, it contain Bluetooth 4.0 LE Module operating at 2.4GHz
ISM band; the frequencies allocated for the Bluetooth 4.0 LE is F(MHz)=2402+2*n (0<=n<=39).
The lowest, middle, highest channel numbers of the Bluetooth Module used and tested in this
report are separately 0 (2402MHz), 19 (2440MHz) and 39 (2480MHz).
The EUT connected to the serial port of the computer with a serial communication cable, we use
the dedicated software to control the EUT continuous transmission.
For a more detailed description, please refer to Specification or User’s Manual supplied by the
applicant and/or manufacturer.
1.2.1 Identification of all used EUTs
The EUT identity consists of numerical and letter characters, the letter character indicates the test
sample, and the following two numerical characters indicate the software version of the test
sample.
EUT Identity
Hardware Version
Software Version
A01
M16-420R1-1 A-12
2.00617
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 5 0f 36
REPORT No.: SZ16110064W02
1.3
Test Standards and Results
The objective of the report is to perform testing according to 47 CFR Part 15 Subpart C (Bluetooth,
2.4GHz ISM band radiators) for the EUT FCC ID Certification:
No.
Identity
Document Title
47 CFR Part 15
(10-1-15 Edition)
Radio Frequency Devices
Test detailed items/section required by FCC rules and results are as below:
No.
Section
Description
15.203
Antenna Requirement
15.247(b)
Test Date
Result
N/A
N/A
Peak Output Power
Nov 16, 2016
PASS
15.247(a)
Bandwidth
Nov 16, 2016
PASS
15.247(d)
Conducted Spurious Emission
and Band Edge
Nov 16, 2016
PASS
15.247(d)
Restricted Frequency Bands
Nov 25, 2016
PASS
15.207
Conducted Emission
Nov 25, 2016
PASS
15.209 ,15.247(d)
Radiated Emission
Nov 25, 2016
PASS
15.247(e)
Power spectral density (PSD)
Nov 16, 2016
PASS
The tests were performed according to the method of measurements prescribed in ANSI
C63.10-2013 and KDB558074 D01 v03r05 (04/08/2016).
1.3.1 Test Environment Conditions
During the measurement, the environmental conditions were within the listed ranges:
Temperature (°C):
15 - 35
Relative Humidity (%):
30 -60
Atmospheric Pressure (kPa):
86-106
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 6 0f 36
REPORT No.: SZ16110064W02
2. 47 CFR PART 15C REQUIREMENTS
2.1
Antenna requirement
2.1.1 Applicable Standard
According to FCC 15.203, an intentional radiator shall be designed to ensure that no antenna other
than that furnished by the responsible party shall be used with the device. The use of a
permanently attached antenna or of an antenna that uses a unique coupling to the intentional
radiator shall be considered sufficient to comply with the provisions of this section.
2.1.2 Result: Compliant
The EUT has a permanently and irreplaceable attached antenna. Please refer to the EUT internal
photos.
2.2
Peak Output Power
2.2.1 Requirement
According to FCC section 15.247(b)(3), For systems using digital modulation in the 902-928 MHz,
2400-2483.5 MHz, and 5725-5850 MHz bands: The maximum peak conducted output power of the
intentional radiator shall not exceed 1 Watt.
2.2.2 Test Description
The measured output power was calculated by the reading of the spectrum analyzer and
calibration.
A. Test Setup:
The EUT (Equipment under the test) which is powered by the adapter is coupled to the Spectrum
analyzer; the RF load attached to the EUT antenna terminal is 50Ohm; the path loss as the factor
is calibrated to correct the reading, all test result in Spectrum analyzer.
B. Equipments List:
Please reference ANNEX A (1.5).
2.2.3 Test procedure
The measured output power was calculated by the reading of the spectrum analyzer and
calibration. Following is the test procedure for Peak Output Power test on the spectrum analyzer:
a) Set analyzer center frequency to channel center frequency.
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 7 0f 36
REPORT No.: SZ16110064W02
b)Set the RBW to1MHz
c) Set VBW to 3MHz
d) Set span to 3MHz
e) Sweep time to auto couple.
f) Detector = peak.
g) Trace mode = max hold.
h) Allow trace to fully stabilize.
i) Use peak marker function to determine the peak amplitude level.
2.2.4 Test Result
The lowest, middle and highest channels are selected to perform testing to verify the conducted
RF output peak power of the Module.
A. Test Verdict:
dBm
Refer to
Plot
2402
-0.69
0.0009
Plot A
19
2440
-1.51
0.0007
Plot B
39
2480
-2.18
0.0006
Plot C
Channel
Frequency
(MHz)
Measured Output Peak Power
Limit
dBm
Verdict
PASS
30
PASS
PASS
B. Test Plots:
(Plot A: Channel 0: 2402MHz)
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 8 0f 36
REPORT No.: SZ16110064W02
(Plot B: Channel 19: 2440MHz)
(Plot C: Channel 39: 2480MHz)
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 9 0f 36
REPORT No.: SZ16110064W02
2.3
6dB Bandwidth
2.3.1 Requirement
According to FCC section 15.247(a) (2), Systems using digital modulation techniques may operate
in the 902 - 928 MHz, 2400 - 2483.5 MHz, and 5725 - 5850 MHz bands. The minimum 6 dB
bandwidth shall be at least 500 kHz.
2.3.2 Test Description
A. Test Set:
The EUT which is powered by the adapter, is coupled to the Spectrum Analyzer; the RF load
attached to the EUT antenna terminal is 50Ohm; the path loss as the factor is calibrated to correct
the reading.
Make the measurement with the spectrum analyzer's resolution bandwidth (RBW) = 100 kHz. In
order to make an accurate measurement, set the span greater than RBW.
B. Equipments List:
Please reference ANNEX A(1.5).
2.3.3 Test procedure
The steps for the first option are as follows:
1 Set analyzer center frequency to channel center frequency.
a) Set RBW = 100 kHz.
b) Set the VBW=300 kHz.
c) Detector = peak.
d) Trace mode = max hold.
e) Sweep = auto couple
f) Allow the trace to stabilize.
g) Measure the maximum width of the emission that is constrained by the frequencies associated
with the two outermost amplitude points (upper and lower frequencies) that are attenuated by
6 dB relative to the maximum level measured in the fundamental emission.
2 The automatic bandwidth measurement capability of an instrument may be employed using
the X dB bandwidth mode with X set to 6 dB, if the functionality described in 11.8.1 (i.e., RBW =
100 kHz,VBW ≥ 3 × RBW, and peak detector with maximum hold) is implemented by the
instrumentation function. When using this capability, care shall be taken so that the bandwidth
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 10 0f 36
REPORT No.: SZ16110064W02
measurement is not influenced by any intermediate power nulls in the fundamental emission that
might be ≥6 dB.
2.3.4 Test Result
The lowest, middle and highest channels are selected to perform testing to record the 6 dB
bandwidth of the module.
A.
Test Verdict:
Channel
Frequency
(MHz)
6 dB
Bandwidth
(MHz)
Refer to
Plot
Limits(kHz)
Result
2402
0.7465
Plot A
≥500
PASS
19
2440
0.7462
Plot B
≥500
PASS
39
2480
0.7552
Plot C
≥500
PASS
B. Test Plots:
(Plot A: Channel 0: 2402MHz)
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 11 0f 36
REPORT No.: SZ16110064W02
(Plot B: Channel 19: 2440 MHz)
(Plot C: Channel 39: 2480MHz)
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 12 0f 36
REPORT No.: SZ16110064W02
2.4
Conducted Spurious Emissions and Band Edge
2.4.1 Requirement
According to FCC section 15.247(d), in any 100kHz bandwidth outside the frequency band in
which the spread spectrum or digitally modulated intentional radiator is operating, the radio
frequency power that is produced by the intentional radiator shall be at least 20dB below that in the
100kHz bandwidth within the band that contains the highest level of the desired power, based on
either an RF conducted or a radiated measurement.
2.4.2 Test Description
A. Test Set:
The EUT which is powered by the adapter, is coupled to the Spectrum Analyzer; the RF load
attached to the EUT antenna terminal is 50Ohm; the path loss as the factor is calibrated to correct
the reading.
Make the measurement with the spectrum analyzer's resolution bandwidth (RBW) = 100 kHz. In
order to make an accurate measurement, set the span greater than RBW.
B. Equipments List:
Please reference ANNEX A (1.5).
2.4.3 Test Result
The measurement frequency range is from 30MHz to the 10th harmonic of the fundamental
frequency. The lowest, middle and highest channels are tested to verify the spurious emissions.
A. Test Verdict:
Channel
Frequency
(MHz)
Measured Max.
Out of Band
Emission (dBm)
Refer to
Plot
2402
-45.58
19
2440
39
2480
Limit (dBm)
Carrier
Level
Calculated
-20dBc Limit
Verdict
Plot A.1
-1.12
-21.12
PASS
-45.74
Plot B.1
-1.67
-21.67
PASS
-46.12
Plot C.1
-2.36
-22.36
PASS
B. Test Plots:
Note: the power of the Module transmitting frequency should be ignored.
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 13 0f 36
REPORT No.: SZ16110064W02
(Plot A.1: Channel = 0, 30MHz to 25GHz)
(Band Edge@ Channel = 0)
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 14 0f 36
REPORT No.: SZ16110064W02
M ORLAB GROU P
(Plot B.1:
Channel = 19, 30MHz to 25GHz)
(Plot C.1:
Channel = 39, 30MHz to 25GHz)
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 15 0f 36
REPORT No.: SZ16110064W02
(Band Edge@ Channel = 39)
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 16 0f 36
REPORT No.: SZ16110064W02
2.5
Power spectral density (PSD)
2.5.1 Requirement
For digitally modulated systems, the power spectral density conducted from the intentional radiator
to the antenna shall not be greater than 8dBm in any 3 kHz band during any time interval of
continuous transmission. This power spectral density shall be determined in accordance with the
provisions of paragraph (b) of this section. The same method of determining the conducted output
power shall be used to determine the power spectral density.
2.5.2 Test Description
A. Test Set:
The EUT which is powered by the adapter, is coupled to the Spectrum Analyzer; the RF load
attached to the EUT antenna terminal is 50Ohm; the path loss as the factor is calibrated to correct
the reading.
B. Equipments List:
Please reference ANNEX A (1.5).
2.5.3 Test procedure
The measured power spectral density was calculated by the reading of the spectrum analyzer and
calibration. Following is the test procedure for PSD test:
a) Set analyzer center frequency to channel center frequency.
b) Set the span to 3MHz
c) Set the RBW to 3 kHz
d) Set the VBW to 10KHz
e) Detector = peak.
f) Sweep time = auto couple.
g) Trace mode = max hold.
h) Allow trace to fully stabilize.
i) Use the peak marker function to determine the maximum amplitude level within the RBW.
2.5.4 Test Result
The lowest, middle and highest channels are tested.
A. Test Verdict:
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 17 0f 36
REPORT No.: SZ16110064W02
Spectral power density (dBm/3kHz)
Channel
Frequency
(MHz)
Measured PSD
(dBm/3kHz)
Refer to Plot
Limit
(dBm/3kHz)
Verdict
2402
-14.80
Plot A
PASS
19
2440
-14.46
Plot B
PASS
39
2480
-15.36
Plot C
PASS
Measurement uncertainty: ±1.3dB
B. Test Plots:
(Plot A: Channel = 0)
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 18 0f 36
REPORT No.: SZ16110064W02
(Plot B: Channel = 19)
(Plot C: Channel = 39)
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 19 0f 36
REPORT No.: SZ16110064W02
2.6
Restricted Frequency Bands
2.6.1 Requirement
According to FCC section 15.247(d), in any 100kHz bandwidth outside the frequency band in
which the spread spectrum or digitally modulated intentional radiator is operating, the radio
frequency power that is produced by the intentional radiator shall be at least 20dB below that in the
100kHz bandwidth within the band that contains the highest level of the desired power, In addition,
radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply
with the radiated emission limits specified in 15.209(a).
2.6.2 Test Description
A. Test Setup
The EUT is located in a 3m Semi-Anechoic Chamber; the antenna factors, cable loss and so on of
the site as factors are calculated to correct the reading.
For the Test Antenna:
Test Antenna is 3m away from the EUT. Test Antenna height is varied from 1m to 4m above the
ground to determine the maximum value of the field strength.
B. Equipments List:
Please reference ANNEX A(1.5).
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 20 0f 36
REPORT No.: SZ16110064W02
2.6.3 Test Result
The lowest and highest channels are tested to verify the Restricted Frequency Bands.
The measurement results are obtained as below:
E [dBμV/m] =UR + AT + AFactor [dB]; AT =LCable loss [dB]-Gpreamp [dB]
AT: Total correction Factor except Antenna
UR: Receiver Reading
Gpreamp: Preamplifier Gain
AFactor: Antenna Factor at 3m
Note: Restricted Frequency Bands were performed when antenna was at vertical and horizontal
polarity, and only the worse test condition (vertical) was recorded in this test report.
A. Test Verdict:
Channel
Frequency
(MHz)
Detector
PK/ AV
Receiver
Reading
UR
(dBuV)
AT
(dB)
Max.
AFactor
Emission
Limit
Verdict
(dB@3m)
(dBµV/m)
(dBµV/m)
2363.23
PK
46.22
-33.63
32.56
45.15
74
Pass
2381.85
AV
32.94
-33.63
32.56
31.87
54
Pass
39
2486.51
PK
50.01
-33.18
32.5
49.33
74
Pass
39
2485.39
AV
32.93
-33.18
32.5
32.25
54
Pass
B. Test Plots:
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 21 0f 36
REP
PORT No.: SZ16110
0064W02
(Plot A1: Channel
= 0 PEAK)
(Plot A2: Channel = 0 AVG)
M ORLAB
B GROU
UP
FL1-3, Building A, FeiYang Scie
ence Park, No.8 Long
gChang Road,
Tel: 86-755--36698555
Fax: 86-755-36698525
Block67, BaoAn
District, Shen
nZhen , GuangDong
g Province, P. R. Ch
hina
Http://www.m
morlab.com
E-m
mail: service@morlab.cn
Page 22 0f 36
REP
PORT No.: SZ16110
0064W02
(Plot B1: Channel
= 39
3 PEAK)
(Plot B2: Channel = 39 AVG)
M ORLAB
B GROU
UP
FL1-3, Building A, FeiYang Scie
ence Park, No.8 Long
gChang Road,
Tel: 86-755--36698555
Fax: 86-755-36698525
Block67, BaoAn
District, Shen
nZhen , GuangDong
g Province, P. R. Ch
hina
Http://www.m
morlab.com
E-m
mail: service@morlab.cn
Page 23 0f 36
REPORT No.: SZ16110064W02
2.7
Conducted Emission
2.7.1 Requirement
According to FCC section 15.207, for an intentional radiator that is designed to be connected to the
public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power
line on any frequency within the band 150kHz to 30MHz shall not exceed the limits in the following
table, as measured using a 50µH/50Ω line impedance stabilization network (LISN).
Frequency
(MHz)
range Conducted Limit (dBµV)
Quai-peak
Average
0.15 - 0.50
66 to 56
56 to 46
0.50 - 5
56
46
5 - 30
60
50
NOTE:
(a) The lower limit shall apply at the band edges.
(b) The limit decreases linearly with the logarithm of the frequency in the range 0.15 - 0.50MHz.
2.7.2 Test Description
A. Test Setup:
The Table-top EUT was placed upon a non-metallic table 0.8m above the horizontal metal
reference ground plane. EUT was connected to LISN and LISN was connected to reference
Ground Plane. EUT was 80cm from LISN. The set-up and test methods were according to ANSI
C63.10: 2013.
B. Equipments List:
Please reference ANNEX A(1.5).
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 24 0f 36
REPORT No.: SZ16110064W02
2.7.3 Test Result
The maximum conducted interference is searched using Peak (PK), if the emission levels more
than the AV and QP limits, and that have narrow margins from the AV and QP limits will be
re-measured with AV and QP detectors. Tests for both L phase and N phase lines of the power
mains connected to the EUT are performed. Refer to recorded points and plots below.
A. Test setup:
The EUT configuration of the emission tests is EUT + Link.
Note: The test voltage is AC 120V/60Hz.
B. Test Plots:
(Plot A: L Phase)
Emission Level (dBµV)
Limit (dBµV)
Fre.
(MHz)
Quai-peak
Average
Quai-peak
Average
0.16
57.07
39.68
65.71
55.71
PASS
0.625
38.52
27.73
52.43
42.43
PASS
1.605
32.73
25.16
56
46
2.07
31.88
23.45
56
46
2.515
30.85
14.25
56
46
PASS
2.995
29.56
19.53
56
46
PASS
NO.
M ORLAB GROU P
Powerline
Line
Verdict
PASS
PASS
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 25 0f 36
REPORT No.: SZ16110064W02
(Plot B: N Phase)
Emission Level (dBµV)
Limit (dBµV)
Fre.
(MHz)
Quai-peak
Average
Quai-peak
Average
0.15
54.77
31.79
66
56
PASS
0.59
40.85
30.34
56
46
PASS
1.255
32.29
27.09
56
46
1.75
31.15
26.54
56
46
11.915
21.74
25.81
60
50
PASS
14.42
25.73
24.50
60
50
PASS
NO.
M ORLAB GROU P
Powerline
Line
Verdict
PASS
PASS
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 26 0f 36
REPORT No.: SZ16110064W02
2.8
Radiated Emission
2.8.1 Requirement
According to FCC section 15.247(d), radiated emission outside the frequency band attenuation
below the general limits specified in FCC section 15.209(a) is not required. In addition, radiated
emissions which fall in the restricted bands, as defined in FCC section 15.205(a), must also
comply with the radiated emission limits specified in FCC section 15.209(a).
According to FCC section 15.209 (a), except as provided elsewhere in this subpart, the emissions
from an intentional radiator shall not exceed the field strength levels specified in the following table:
Frequency (MHz)
Field Strength (µV/m)
Measurement Distance (m)
0.009 - 0.490
2400/F(kHz)
300
0.490 - 1.705
24000/F(kHz)
30
1.705 - 30.0
30
30
30 - 88
100
88 - 216
150
216 - 960
200
Above 960
500
Note:
1.
For Above 1000MHz, the emission limit in this paragraph is based on measurement
instrumentation employing an average detector, measurement using instrumentation with
a peak detector function, corresponding to 20dB above the maximum permitted average
limit.
2.
For above 1000MHz, limit field strength of harmonics: 54dBuV/m@3m (AV) and
74dBuV/m@3m (PK)
In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a),
also should comply with the radiated emission limits specified in Section 15.209(a)(above table)
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 27 0f 36
REPORT No.: SZ16110064W02
2.8.2 Test Description
A. Test Setup:
1)
For radiated emissions from 9kHz to 30MHz
2)
For radiated emissions from 30MHz to1GHz
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 28 0f 36
REPORT No.: SZ16110064W02
3)
For radiated emissions above 1GHz
The RF absorbing material used on the reference ground plane and on the turntable have a
maximum height (thickness) of 30 cm (12 in) and have a minimum-rated attenuation of 20 dB at all
frequencies from 1 GHz to 18 GHz. Test site have a minimum area of the ground plane covered
with RF absorbing material as specified in Figure 6 of ANSI C63.4: 2014.
The test site semi-anechoic chamber has met the requirement of NSA tolerance 4dB according to
the standards: ANSI C63.10:2013. For radiated emissions below or equal to 1GHz, The EUT was
set-up on insulator 80cm above the Ground Plane, For radiated emissions above 1GHz, The EUT
was set-up on insulator 150cm above the Ground Plane. The set-up and test methods were
according to ANSI C63.10:2013.
The EUT is located in a 3m Semi-Anechoic Chamber; the antenna factors, cable loss and so on of
the site as factors are calculated to correct the reading.
For the Test Antenna:
(a) In the frequency range of 9kHz to 30MHz, magnetic field is measured with Loop Test Antenna.
The Test Antenna is positioned with its plane vertical at 1m distance from the EUT. The center of
the Loop Test Antenna is 1m above the ground. During the measurement the Loop Test Antenna
rotates about its vertical axis for maximum response at each azimuth about the EUT.
(b) In the frequency range above 30MHz, Bi-Log Test Antenna (30MHz to 1GHz) and Horn Test
Antenna (above 1GHz) are used. Place the test antenna at 3m away from area of the EUT, while
keeping the test antenna aimed at the source of emissions at each frequency of significant
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 29 0f 36
REPORT No.: SZ16110064W02
emissions, with polarization oriented for maximum response. The test antenna may have to be
higher or lower than the EUT, depending on the radiation pattern of the emission and staying
aimed at the emission source for receiving the maximum signal. The final test antenna elevation
shall be that which maximizes the emissions. The test antenna elevation for maximum emissions
shall be restricted to a range of heights of from 1 m to 4 m above the ground or reference ground
plane. The emission levels at both horizontal and vertical polarizations should be tested.
B. Equipments List:
Please reference ANNEX A(1.5).
2.8.3 Test Result
According to ANSI C63.10, because of peak detection will yield amplitudes equal to or greater than
amplitudes measured with the quasi-peak (or average) detector, the measurement data from a
spectrum analyzer peak detector will represent the worst-case results, if the peak measured value
complies with the quasi-peak limit, it is unnecessary to perform an quasi-peak measurement.
The measurement results are obtained as below:
E [dBμV/m] =UR + AT + AFactor [dB]; AT =LCable loss [dB]-Gpreamp [dB]
AT: Total correction Factor except Antenna
UR: Receiver Reading
Gpreamp: Preamplifier Gain
AFactor: Antenna Factor at 3m
During the test, the total correction Factor AT and AFactor were built in test software.
Note: All radiated emission tests were performed in X, Y, Z axis direction. And only the worst axis
test condition was recorded in this test report.
The low frequency, which started from 9KHz to 30MHz, was pre-scanned and the result which was
20dB lower than the limit line per 15.31(o) was not reported.
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 30 0f 36
REPORT No.: SZ16110064W02
A. Test Plots for the Whole Measurement Frequency Range:
Plots for Channel = 0
Fre.
(MHz)
44.568
Pk
(dBμV/m)
9.62
QP
(dBμV/m)
N/A
AV
(dBμV/m)
N/A
Limit-PK
(dBμV/m)
N/A
Limit-QP
(dBμV/m)
40.00
Limit-AV
(dBμV/m)
N/A
Antenna
Verdict
Horizontal
PASS
99.199
10.86
N/A
N/A
N/A
43.50
N/A
Horizontal
PASS
367.497
18.39
N/A
N/A
N/A
46.00
N/A
Horizontal
PASS
2365.026
50.09
N/A
N/A
74.0
N/A
54.00
Horizontal
PASS
5752.864
46.97
N/A
N/A
74.0
N/A
54.00
Horizontal
PASS
18559.847
51.71
N/A
N/A
74.0
N/A
54.00
Horizontal
PASS
(Antenna Horizontal, 30MHz to 25GHz)
Fre.
(MHz)
48.210
Pk
(dBμV/m)
8.64
QP
(dBμV/m)
N/A
AV
(dBμV/m)
N/A
Limit-PK
(dBμV/m)
N/A
Limit-QP
(dBμV/m)
40.00
Limit-AV
(dBμV/m)
N/A
104.055
11.99
N/A
N/A
N/A
43.50
363.855
20.81
N/A
N/A
N/A
2365.026
50.01
N/A
N/A
5752.864
46.92
N/A
18567.994
50.97
N/A
Antenna
Verdict
Vertical
PASS
N/A
Vertical
PASS
46.00
N/A
Vertical
PASS
74.0
N/A
54.0
Vertical
PASS
N/A
74.0
N/A
54.0
Vertical
PASS
N/A
74.0
N/A
54.0
Vertical
PASS
(Antenna Vertical, 30MHz to 25GHz)
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 31 0f 36
REPORT No.: SZ16110064W02
Plot for Channel = 19
Fre.
(MHz)
49.424
Pk
(dBμV/m)
9.33
QP
(dBμV/m)
N/A
AV
(dBμV/m)
N/A
Limit-PK
(dBμV/m)
N/A
Limit-QP
(dBμV/m)
40.00
Limit-AV
(dBμV/m)
N/A
Antenna
Verdict
Horizontal
PASS
102.841
11.19
N/A
N/A
N/A
43.50
N/A
Horizontal
PASS
400.275
18.43
N/A
N/A
N/A
46.00
N/A
Horizontal
PASS
2365.026
46.92
N/A
N/A
74.0
N/A
54.00
Horizontal
PASS
5761.011
47.31
N/A
N/A
74.0
N/A
54.00
Horizontal
PASS
18543.553
50.86
N/A
N/A
74.0
N/A
54.00
Horizontal
PASS
(Antenna Horizontal, 30MHz to 25GHz)
Fre.
(MHz)
49.424
Pk
(dBμV/m)
9.71
QP
(dBμV/m)
N/A
AV
(dBμV/m)
N/A
Limit-PK
(dBμV/m)
N/A
Limit-QP
(dBμV/m)
40.00
Limit-AV
(dBμV/m)
N/A
100.413
12.98
N/A
N/A
N/A
43.50
457.334
17.74
N/A
N/A
N/A
2365.026
50.70
N/A
N/A
6180.578
47.02
N/A
18531.333
50.81
N/A
Antenna
Verdict
Vertical
PASS
N/A
Vertical
PASS
46.00
N/A
Vertical
PASS
74.0
N/A
54.0
Vertical
PASS
N/A
74.0
N/A
54.0
Vertical
PASS
N/A
74.0
N/A
54.0
Vertical
PASS
(Antenna Vertical, 30MHz to 25GHz)
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 32 0f 36
REPORT No.: SZ16110064W02
Plot for Channel = 39
Fre.
(MHz)
44.568
Pk
(dBμV/m)
9.43
QP
(dBμV/m)
N/A
AV
(dBμV/m)
N/A
Limit-PK
(dBμV/m)
N/A
Limit-QP
(dBμV/m)
40.00
Limit-AV
(dBμV/m)
N/A
Antenna
Verdict
Horizontal
PASS
100.413
11.27
N/A
N/A
N/A
43.50
N/A
Horizontal
PASS
335.932
18.81
N/A
N/A
N/A
46.00
N/A
Horizontal
PASS
2089.716
43.50
N/A
N/A
74.0
N/A
54.0
Horizontal
PASS
5667.321
46.84
N/A
N/A
74.0
N/A
54.0
Horizontal
PASS
18531.333
51.21
N/A
N/A
74.0
N/A
54.0
Horizontal
PASS
(Antenna Horizontal, 30MHz to 25GHz)
Fre.
(MHz)
48.210
Pk
(dBμV/m)
9.50
QP
(dBμV/m)
N/A
AV
(dBμV/m)
N/A
Limit-PK
(dBμV/m)
N/A
Limit-QP
(dBμV/m)
40.00
Limit-AV
(dBμV/m)
N/A
101.627
11.65
N/A
N/A
N/A
43.50
584.806
20.68
N/A
N/A
N/A
2233.774
44.49
N/A
N/A
9027.932
49.14
N/A
18331.733
51.14
N/A
Antenna
Verdict
Vertical
PASS
N/A
Vertical
PASS
46.00
N/A
Vertical
PASS
74.0
N/A
54.0
Vertical
PASS
N/A
74.0
N/A
54.0
Vertical
PASS
N/A
74.0
N/A
54.0
Vertical
PASS
(Antenna Vertical, 30MHz to 25GHz)
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 33 0f 36
REPORT No.: SZ16110064W02
ANNEX A GENERAL INFORMATION
1.1
Identification of the Responsible Testing Laboratory
Company Name:
Shenzhen Morlab Communications Technology Co., Ltd.
Department:
Morlab Laboratory
Address:
FL.3, Building A, FeiYang Science Park, No.8 LongChang
Road, Block 67, BaoAn District, ShenZhen, GuangDong
Province, P. R. China
Responsible Test Lab Manager:
Mr. Su Feng
Telephone:
+86 755 36698555
Facsimile:
+86 755 36698525
1.2
Identification of the Responsible Testing Location
Name:
Shenzhen Morlab Communications Technology Co., Ltd.
Morlab Laboratory
Address:
FL.3, Building A, FeiYang Science Park, No.8 LongChang
Road, Block 67, BaoAn District, ShenZhen, GuangDong
Province, P. R. China
1.3
Facilities and Accreditations
Shenzhen Morlab Communications Technology Co., Ltd. Morlab Laboratory is a testing
organization accredited by China National Accreditation Service for Conformity Assessment
(CNAS) according to ISO/IEC 17025. The accreditation certificate number is L3572.
All measurement facilities used to collect the measurement data are located at FL.1, Building A,
FeiYang Science Park, Block 67, BaoAn District, Shenzhen, 518101 P. R. China. The test site is
constructed in conformance with the requirements of ANSI C63.10-2013 and CISPR Publication
22; the FCC registration number is 695796.
1.4
Maximum measurement uncertainty
Where relevant, the following measurement uncertainty levels have been estimated for test
performed on the EUT as specified in CISPR 16-1-2:
Test items
Uncertainty
Peak Output Power
±2.22dB
Power spectral density (PSD)
±2.22dB
Bandwidth
±5%
Conducted Spurious Emission
±2.77 dB
Restricted Frequency Bands
±5%
Radiated Emission
±2.95dB
Conducted Emission
±2.44dB
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 34 0f 36
REPORT No.: SZ16110064W02
This uncertainty represent an expanded uncertainty expressed at approximately the 95%
confidence level using a coverage factor of k=2
1.5
1.5.1
Test Equipments Utilized
Conducted Test Equipments
Conducted Test Equipment
No.
Equipment Name
Serial No.
Type
Manufacturer
Cal. Date
Cal. Due
Spectrum Analyzer
MY45101810
E4407B
Agilent
2016.06.02
2017.06.01
Power Splitter
NW521
1506A
Weinschel
2016.06.02
2017.06.01
Attenuator 1
(N/A.)
10dB
Resnet
2016.06.02
2017.06.01
Attenuator 2
(N/A.)
3dB
Resnet
2016.06.02
2017.06.01
EXA Signal
Analzyer
MY53470836
N9010A
Agilent
2015.12.07
2016.12.06
RF cable
(30MHz-26GHz)
CB01
RF01
Morlab
N/A
N/A
Coaxial cable
CB02
RF02
Morlab
N/A
N/A
SMA connector
CN01
RF03
HUBER-SUHNER
N/A
N/A
1.5.2
Conducted Emission Test Equipments
Conducted Emission Test Equipments
No.
Equipment Name
Serial No.
Type
Manufacturer
Cal. Date
Cal. Due
Receiver
US44210471
E7405A
Agilent
2016.06.02
2017.06.01
LISN
812744
NSLK 8127
Schwarzbeck
2016.06.02
2017.06.01
Service Supplier
100448
CMU200
R&S
2016.06.02
2017.06.01
Pulse Limiter
(20dB)
9391
VTSD
9561-D
Schwarzbeck
2016.06.02
2017.06.01
Coaxial cable(BNC)
(30MHz-26GHz)
CB01
EMC01
Morlab
N/A
N/A
1.5.3
Auxiliary Test Equipment
Auxiliary Test Equipment
No.
Equipment Name
Model No.
Brand Name
Manufacturer
Cal.Date
Cal.Due Date
Computer
T430i
Think Pad
Lenovo
N/A
N/A
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 35 0f 36
REPORT No.: SZ16110064W02
1.5.4
Radiated Test Equipments
Radiated Test Equipments
No.
Equipment Name
Serial No.
Type
Manufacturer
Cal. Date
Cal.Due
Date
System Simulator
GB45360846
8960-E5515C
Agilent
2016.06.02
2017.06.01
Receiver
MY54130016
N9038A
Agilent
2016.06.02
2017.06.01
Test Antenna Bi-Log
N/A
VULB9163
Schwarzbeck
2016.07.05
2017.07.04
Test Antenna - Horn
9170C-531
BBHA9170
Schwarzbeck
2016.07.05
2017.07.04
Test Antenna - Loop
1519-022
FMZB1519
Schwarzbeck
2016.07.05
2017.07.04
Test Antenna - Horn
71688
BBHA 9120D
Schwarzbeck
2016.07.05
2017.07.04
Coaxial cable
(N male)
(9KHz-30MHz)
CB04
EMC04
Morlab
N/A
N/A
Coaxial cable
(N male)
(30MHz-26GHz)
CB02
EMC02
Morlab
N/A
N/A
Coaxial cable(N
male)
(30MHz-26GHz)
CB03
EMC03
Morlab
N/A
N/A
10
1-18GHz
pre-Amplifier
MA02
TS-PR18
Rohde&
Schwarz
2016.07.05
2017.07.04
11
18-26.5GHz
pre-Amplifier
MA03
TS-PR18
Rohde&
Schwarz
2016.07.05
2017.07.04
1.5.5
Climate Chamber
Climate Chamber
No.
Equipment Name
Serial No.
Type
Manufacturer
Cal.Date
Cal.Due Date
Climate Chamber
2004012
HL4003T
Yinhe
2016.03.25
2017.03.24
1.5.6
Vibration Table
Vibration Table
No.
Equipment Name
Serial No.
Type
Manufacturer
Cal.Date
Cal.Due Date
Vibration Table
N/A
ACT2000-S015L
CMI-COM
2016.03.25
2017.03.24
1.5.7
Anechoic Chamber
Anechoic Chamber
No.
Equipment Name
Serial No.
Type
Manufacturer
Cal.Date
Cal.Due Date
Anechoic Chamber
N/A
9m*6m*6m
Changning
2016.03.25
2017.03.24
***** END OF REPORT *****
M ORLAB GROU P
FL1-3, Building A, FeiYang Science Park, No.8 LongChang Road,
Tel: 86-755-36698555
Fax: 86-755-36698525
Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China
Http://www.morlab.com
E-mail: service@morlab.cn
Page 36 0f 36
Download: 16420NEX Customizable smart band Test Report SZ16110064W02_bt4.0 fccx Mighty Cast, Inc
Mirror Download [FCC.gov]16420NEX Customizable smart band Test Report SZ16110064W02_bt4.0 fccx Mighty Cast, Inc
Document ID3246155
Application IDo9soGDKE46ZgY+6gaNVxhA==
Document DescriptionTest Report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize169.55kB (2119409 bits)
Date Submitted2017-01-04 00:00:00
Date Available2017-01-10 00:00:00
Creation Date2017-12-20 07:54:30
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-12-20 07:54:30
Document TitleSZ16110064W02_bt4.0 fccx
Document CreatorPScript5.dll Version 5.2.2
Document Author: Administrator

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:98bf4014-a2fd-11f2-0000-02c7314339d4
Producer                        : GPL Ghostscript 9.18
Modify Date                     : 2017:07:17 11:14:06Z
Create Date                     : 2017:07:17 11:14:06Z
Creator Tool                    : UnknownApplication
Document ID                     : uuid:98bf4014-a2fd-11f2-0000-02c7314339d4
Format                          : application/pdf
Title                           : Untitled
EXIF Metadata provided by EXIF.tools

Facebook Twitter Google+ RSS © FCCID.io 2018