F04J Mobile Phone RF Exposure Info Test Report_SAR Fujitsu Limited

Fujitsu Limited Mobile Phone

FCC ID Filing: VQK-F04J
Purchase on Amazon: Mobile Phone

Trouble Viewing? See the or view the HTML Version or PDF in frame
Page 1 of F04J Mobile Phone RF Exposure Info Test Report_SAR Fujitsu Limited

Report No. : E5/2016/B0002
Page : 1 of 130
SAR TEST REPORT
The following samples were submitted and identified on behalf of the client as:
Equipment Under Test
Mobile Phone
Brand Name
FUJITSU
Model No.
F-04J
Company Name
Fujitsu Limited
1-1, Kamikodanaka 4-chome, Nakahara-ku, Kawasaki
211-8588, Japan
Company Address
Standards
IEEE/ANSI C95.1-1992, IEEE 1528-2013,
KDB248227D01v02r02,KDB865664D01v01r04,
KDB865664D02v01r02,KDB941225D01v03r01,
KDB941225D06v02r01,KDB447498D01v06,
KDB648474D04v01r03,
FCC ID
VQK-F04J
Date of Receipt
Nov. 07, 2016
Date of Test(s)
Nov. 22, 2016 ~ Nov. 25, 2016
Date of Issue
Jan. 04, 2017
In the configuration tested, the EUT complied with the standards specified above.
Remarks:
This report details the results of the testing carried out on two sample, the results contained in this test
report do not relate to other samples of the same product. The manufacturer should ensure that all products in
series production are in conformity with the product sample detailed in this report.
This report may only be reproduced and distributed in full. If the product in this report is used in any
configuration other than that detailed in the report, the manufacturer must ensure the new system complies
with all relevant standards. Any mention of SGS Taiwan Electronic & Communication Laboratory or testing
done by SGS Taiwan Electronic & Communication Laboratory in connection with distribution or use of the
product described in this report must be approved by SGS Taiwan Electronic & Communication Laboratory in
writing.
Signed on behalf of SGS
Engineer
Supervisor
Matt Kuo
Date: Jan. 04, 2017
John Yeh
Date: Jan. 04, 2017
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 2 of 130
Revision History
Report Number
Revision
Description
Issue Date
E5/2016/B0002
Rev.00
Initial creation of document
Dec. 12, 2016
E5/2016/B0002
Rev.01
1st modification
Dec. 13, 2016
E5/2016/B0002
Rev.02
2nd modification
Dec. 14, 2016
E5/2016/B0002
Rev.03
3rd modification
Dec. 15, 2016
E5/2016/B0002
Rev.04
4th modification
Jan. 04, 2017
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 3 of 130
Contents
1. General Information ....................................................................................................... 4
1.1 Testing Laboratory ............................................................................................................... 4
1.2 Details of Applicant.............................................................................................................. 4
1.3 Description of EUT .............................................................................................................. 5
1.4 Test Environment .............................................................................................................. 15
1.5 Operation Description ....................................................................................................... 15
1.6 Positioning Procedure ....................................................................................................... 18
1.7 Evaluation Procedures ...................................................................................................... 20
1.8 Probe Calibration Procedures ........................................................................................... 22
1.9 The SAR Measurement System ........................................................................................ 25
1.10 System Components ....................................................................................................... 27
1.11 SAR System Verification ................................................................................................. 29
1.12 Tissue Simulant Fluid for the Frequency Band ............................................................... 31
1.13 Test Standards and Limits ............................................................................................... 33
2. Summary of Results .................................................................................................... 35
3. Simultaneous Transmission Analysis ........................................................................ 39
3.1 Estimated SAR calculation ................................................................................................ 40
3.2 SPLSR evaluation and analysis ........................................................................................ 40
4. Instruments List ........................................................................................................... 44
5. Measurements .............................................................................................................. 46
6. SAR System Performance Verification ...................................................................... 63
7. DAE & Probe Calibration Certificate .......................................................................... 75
8. Uncertainty Budget ...................................................................................................... 91
9. Phantom Description ................................................................................................... 93
10. System Validation from Original Equipment Supplier ............................................ 94
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 4 of 130
1. General Information
1.1 Testing Laboratory
SGS Taiwan Ltd. Electronics & Communication Laboratory
No.134, Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei
City, Taiwan
Tel
+886-2-2299-3279
Fax
+886-2-2298-0488
Internet
http://www.tw.sgs.com/
1.2 Details of Applicant
Company Name
Company Address
Fujitsu Limited
1-1, Kamikodanaka 4-chome, Nakahara-ku, Kawasaki
211-8588, Japan
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 5 of 130
1.3 Description of EUT
EUT Name
Mobile Phone
Brand Name
FUJITSU
Model No.
F-04J
FCC ID
VQK-F04J
WWAN : 353223080014872
WLAN : 353223080011720
GSM
GPRS
IMEI code
WCDMA
Mode of Operation
HSDPA
HSUPA
WLAN802.11 a/b/g/n(20M/40M)/ac(20M/40M/80M)
Bluetooth
GSM
1/8.3
1/2 (1Dn4UP)
1/2.76 (1Dn3UP)
1/4.1 (1Dn2UP)
1/8.3 (1Dn1UP)
GPRS
Duty Cycle
WCDMA
WLAN802.11 a/b/g/n(20M/40M)/
ac(20M/40M/80M)
Bluetooth
GSM 850
824
─
849
GSM 1900
1850
─
1910
WCDMA Band V
824
─
849
2412
─
2462
5180
─
5240
5190
─
5230
WLAN802.11 b/g/n(20M)
TX Frequency Range
WLAN802.11 a/n(20M)/ac(20M) 5.2G
(MHz)
WLAN802.11 n(40M)/ac(40M) 5.2G
WLAN802.11 ac(80M) 5.2G
5210
WLAN802.11 a/n(20M)/ac(20M) 5.3G
5260
─
5320
WLAN802.11 n(40M)/ac(40M) 5.3G
5270
─
5310
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 6 of 130
WLAN802.11 ac(80M) 5.3G
5500
─
5720
5510
─
5710
5530
─
5690
Bluetooth
2402
─
2480
GSM 850
128
─
251
GSM 1900
512
─
810
WCDMA Band V
4132
─
4233
WLAN802.11 b/g/n(20M)
─
11
WLAN802.11 a/n(20M)/ac(20M) 5.2G
36
─
48
WLAN802.11 n(40M)/ac(40M) 5.2G
38
─
46
WLAN802.11 a/n/ac(20M) 5.6G
TX Frequency Range WLAN802.11 n/ac(40M) 5.6G
(MHz)
WLAN802.11 ac(80M) 5.6G
Channel Number
(ARFCN)
5290
WLAN802.11 ac(80M) 5.2G
42
WLAN802.11 a/n(20M)/ac(20M) 5.3G
52
─
64
WLAN802.11 n(40M)/ac(40M) 5.3G
54
─
62
WLAN802.11 ac(80M) 5.3G
58
WLAN802.11 a/n/ac(20M) 5.6G
100
─
144
WLAN802.11 n/ac(40M) 5.6G
102
─
142
WLAN802.11 ac(80M) 5.6G
106
─
138
─
78
Bluetooth
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 7 of 130
Max. SAR (1 g) (Unit: W/kg)
Mode
Head
Band
Measured Reported
GSM 850
0.114
0.130
GSM 1900
0.310
0.374
WCDMA Band V
0.182
0.190
WLAN802.11 b
0.065
0.087
WLAN802.11 ac(80M)
5.2G
0.135
0.155
WLAN802.11 ac(80M)
5.3G
0.098
0.111
WLAN802.11 ac(80M)
5.6G
0.095
0.111
Position / Channel
Left
Cheek
251
Left
Cheek
512
Left
Cheek
4233
Left
Cheek
Left
Cheek
42
Left
Cheek
58
Left
Cheek
138
Right
Tilt
Channel
Right
Tilt
Channel
Right
Tilt
Channel
Right
Tilt
Channel
Right
Tilt
Channel
Right
Tilt
Channel
Right
Tilt
Channel
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 8 of 130
Max. SAR (1 g) (Unit: W/kg)
Mode
Band
Body-worn
Measured Reported
Position / Channel
GSM 850
0.571
0.653
Front
251
Back
Channel
GSM 1900
0.502
0.605
Front
512
Back
Channel
Bluetooth (GFSK)
0.019
0.024
Front
Back
Channel
WLAN802.11 ac(80M)
5.2G
0.072
0.083
Front
42
Back
Channel
WLAN802.11 ac(80M)
5.3G
0.059
0.067
Front
58
Back
Channel
WLAN802.11 ac(80M)
5.6G
0.027
0.032
Front
138
Back
Channel
Max. SAR (1 g) (Unit: W/kg)
Mode
Band
GPRS 850
(1Dn2UP)
GPRS 1900
(1Dn4UP)
Measured Reported
0.554
0.399
0.632
0.448
Hotspot
mode
WCDMA Band V
WLAN802.11 b
0.755
0.057
0.901
0.077
Position / Channel
Front
Bottom
Left
251
Front
Bottom
Left
810
Front
Bottom
Left
4132
Front
Bottom
Left
Back
Right
Channel
Back
Right
Channel
Back
Right
Channel
Back
Right
Channel
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 9 of 130
GSM/GPRS conducted power (Unit: dBm) table:
EUT mode
824.2
128
836.6
190
33
32.36
23.33
848.8
251
33
32.42
23.39
Frequency
(MHz)
GSM850
(GMSK)
Avg.
(dBm)
32.21
Source
-based
time
average
power
Avg.
(dBm)
23.18
Max.
Rated
Avg.
Power +
Max.
Tolerance
(dBm)
33
CH
Burst
average
power
The division factor compared to the number of TX time slot
1 TX time slot
Division factor
-9.03
Burst average power
Max. Rated Avg. Power +
Max. Tolerance (dBm)
33
30
28
26.5
1Dn4UP
1Dn1UP
1Dn2UP
1Dn3UP
Avg.
Avg.
Avg.
Avg.
CH
(dBm)
(dBm)
(dBm)
(dBm)
32.21
29.38
27.56
26.25
128
27.45
32.36
29.34
26.23
190
27.53
32.42
29.43
26.31
251
Source-based time average power
23.18
23.30
23.36
23.24
824.2
128
GPRS
23.33
23.32
23.19
23.22
836.6
190
850
23.27
23.39
23.41
23.30
848.8
251
The division factor compared to the number of TX time slot
1 TX time slot 2 TX time slot 3 TX time slot 4 TX time slot
Division factor
-9.03
-6.02
-4.26
-3.01
Frequency
EUT mode
(MHz)
824.2
GPRS
836.6
850
848.8
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 10 of 130
EUT mode
Frequency
(MHz)
GSM1900
(GMSK)
1850.2
CH
512
Max.
Rated
Avg.
Power +
Max.
Tolerance
(dBm)
30
Avg.
(dBm)
29.19
Source
-based
time
average
power
Avg.
(dBm)
20.16
Burst
average
power
1800
661
30
29.17
20.14
1909.8
810
30
29.08
20.05
The division factor compared to the number of TX time slot
1 TX time slot
Division factor
-9.03
Burst average power
Max. Rated Avg. Power +
Max. Tolerance (dBm)
30
26.5
25
24
1Dn1UP
1Dn2UP
1Dn3UP
1Dn4UP
Avg.
Avg.
Avg.
Avg.
CH
(dBm)
(dBm)
(dBm)
(dBm)
26.34
29.19
24.60
23.39
512
29.17
24.59
26.32
23.39
661
29.08
24.69
26.40
23.50
810
Source-based time average power
20.32
20.34
20.38
20.16
1850.2
512
GPRS
20.14
20.30
20.33
20.38
1880
661
1900
20.05
20.38
20.43
20.49
1909.8
810
The division factor compared to the number of TX time slot
1 TX time slot 2 TX time slot 3 TX time slot 4 TX time slot
Division factor
-9.03
-6.02
-4.26
-3.01
Frequency
EUT mode
(MHz)
1850.2
GPRS
1880
1900
1909.8
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 11 of 130
WCDMA Band V - HSDPA / HSUPA conducted power (Unit: dBm) table:
Tune-up limit
24.5
Band
WCDMA V
TX Channel
4132
4183
4233
Frequency (MHz)
826.4
836.6
846.6
3GPP Rel 99
RMC 12.2Kbps
23.73
23.93
24.32
3GPP Rel 6
HSDPA Subtest-1
22.92
22.83
23.06
3GPP Rel 6
HSDPA Subtest-2
22.91
22.84
23.19
3GPP Rel 6
HSDPA Subtest-3
22.41
22.43
22.68
3GPP Rel 6
HSDPA Subtest-4
22.41
22.44
22.69
3GPP Rel 6
HSUPA Subtest-1
22.88
22.81
23.17
3GPP Rel 6
HSUPA Subtest-2
22.48
22.39
22.64
3GPP Rel 6
HSUPA Subtest-3
22.89
22.92
23.31
3GPP Rel 6
HSUPA Subtest-4
22.87
22.91
23.14
3GPP Rel 6
HSUPA Subtest-5
22.88
22.92
23.18
HSDPA
HSUPA
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 12 of 130
WLAN802.11 a/b/g/n/ac(20M/40M/80M) conducted power (Unit: dBm) table:
Mode
802.11b
2.4GHz WLAN
802.11g
802.11n-HT20
Mode
802.11a
802.11n-HT20
5.2GHz WLAN
802.11n-VHT20
802.11n-HT40
802.11n-VHT40
802.11n-VHT80
Channel
Frequency
(MHz)
11
11
11
2412
2437
2462
2412
2437
2462
2412
2437
2462
6Mbps
Channel
Frequency
(MHz)
Data Rate
36
40
44
48
36
40
44
48
36
40
44
48
38
46
38
46
42
5180
5200
5220
5240
5180
5200
5220
5240
5180
5200
5220
5240
5190
5230
5190
5230
5210
Data Rate
1Mbps
MCS0
6Mbps
MCS0
MCS0
MCS0
MCS0
MCS0
Tune-up limit
(dBm)
Average power
(dBm)
13.5
13.5
13.5
13
13
13
13
13
13
13.01
12.22
13.12
12.75
12.65
12.76
12.80
12.66
12.70
Tune-up limit
(dBm)
Average power
(dBm)
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
12.61
12.60
12.25
12.62
12.75
12.47
12.53
12.77
12.68
12.37
12.41
12.56
12.59
12.72
12.56
12.27
12.39
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 13 of 130
Channel
Frequency
(MHz)
802.11n-VHT80
52
56
60
64
52
56
60
64
52
56
60
64
54
62
54
62
58
5260
5280
5300
5320
5260
5280
5300
5320
5260
5280
5300
5320
5270
5310
5270
5310
5290
Mode
Channel
Frequency
(MHz)
100
120
140
100
120
124
128
140
100
120
124
128
140
102
118
126
134
102
118
126
134
106
122
138
5500
5600
5700
5500
5600
5620
5640
5700
5500
5600
5620
5640
5700
5510
5590
5630
5670
5510
5590
5630
5670
5530
5610
5690
Mode
802.11a
802.11n-HT20
5.3GHz WLAN
802.11n-VHT20
802.11n-HT40
802.11n-VHT40
802.11a
802.11n-HT20
5.6GHz WLAN
802.11n-VHT20
802.11n-HT40
802.11n-VHT40
802.11n-VHT80
Data Rate
6Mbps
MCS0
MCS0
MCS0
MCS0
MCS0
Data Rate
6Mbps
MCS0
MCS0
MCS0
MCS0
MCS0
Tune-up limit
(dBm)
Average power
(dBm)
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
12.56
12.52
12.30
12.17
12.60
12.52
12.43
12.53
12.39
12.33
12.22
12.32
12.65
12.53
12.42
12.25
12.46
Tune-up limit
(dBm)
Average power
(dBm)
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.02
11.90
11.65
12.03
12.01
12.00
11.93
11.85
11.82
11.89
11.81
11.62
11.64
12.18
12.03
11.94
11.98
12.08
12.17
12.03
11.68
11.77
11.72
11.82
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 14 of 130
Bluetooth conducted power (Unit: dBm) table:
Avg. Tune-up limit (dBm)
10
Average power (dBm)
Mode
Channel
Frequency(MHz)
BR/EDR
39
78
2402
2441
2480
1Mbps
2Mbps
3Mbps
8.91
8.30
8.40
7.00
6.29
6.55
7.02
6.31
6.64
Avg. Tune-up limit (dBm)
Average power (dBm)
Mode
Channel
Frequency(MHz)
BLE
20
39
2402
2442
2480
GFSK
0.66
-0.21
0.07
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 15 of 130
1.4 Test Environment
Ambient Temperature: 22±2° C
Tissue Simulating Liquid: 22±2° C
1.5 Operation Description
1.
The EUT is controlled by using a Radio Communication Tester (Anritsu
MT8820C), and the communication between the EUT and the tester is established
by air link.
2.
Measurements are performed respectively on the lowest, middle and highest
channels of the operating band(s). The EUT is set to maximum power level during
all tests, and at the beginning of each test the battery is fully charged.
3.
During the SAR testing, the DASY 5 system checks power drift by comparing the
e-field strength of one specific location measured at the beginning with that
measured at the end of the SAR testing.
4.
The device doesn’t support EDGE.
5.
SAR test reduction for GPRS and EDGE modes is determined by the
source-based time-averaged output power. The data mode with highest specified
time-averaged output power should be tested for SAR compliance. The GMSK
EDGE configurations are grouped with GPRS and considered with respect to
time-averaged maximum output power to determine compliance. The 3G SAR test
reduction procedure is applied to 8-PSK EDGE with GMSK GPRS/EDGE as the
primary mode. Since the maximum output power in a secondary mode (8-PSK
EDGE) is ≤ ¼ dB higher than the primary mode (GMSK GPRS/EDGE), SAR
measurement is not required for the secondary mode (8-PSK EDGE).
6.
The 3G SAR test reduction procedure is applied to HSDPA with 12.2 kbps RMC
as the primary mode. Since the maximum output power in a secondary mode
(HSDPA) is ≤ ¼ dB higher than the primary mode (WCDMA), SAR measurement is
not required for the secondary mode (HSDPA).
7.
The 3G SAR test reduction procedure is applied to HSPA (HSUPA/HSDPA with
RMC) with 12.2 kbps RMC as the primary mode. Since the maximum output power
in a secondary mode (HSPA) is ≤ ¼ dB higher than the primary mode (WCDMA),
SAR measurement is not required for the secondary mode (HSPA).
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 16 of 130
WLAN
802.11b DSSS SAR Test Requirements:
8.
SAR is measured for 2.4 GHz 802.11b DSSS mode using the highest measured
maximum output power channel, when the reported SAR of the highest measured
maximum output power channel for the exposure configuration is ≤ 0.8 W/kg, no
further SAR testing is required for 802.11b DSSS in that exposure configuration.
9.
When the reported SAR is > 0.8 W/kg, SAR is required for that exposure
configuration using the next highest measured output power channel. When any
reported SAR is > 1.2 W/kg, SAR is required for the third channel; i.e., all channels
require testing.
802.11g/n OFDM SAR Test Exclusion Requirements:
10. SAR is not required for 802.11g/n since the highest reported SAR for DSSS is
adjusted by the ratio of OFDM to DSSS specified maximum output power and the
adjusted SAR is ≤ 1.2 W/kg.
Initial Test Configuration:
11. An initial test configuration is determined for OFDM transmission modes
according to the channel bandwidth, modulation and data rate combination(s) with
the highest maximum output power specified for production units in each
standalone and aggregated frequency band.
12. SAR is measured using the highest measured maximum output power channel.
When the reported SAR of the initial test configuration is > 0.8 W/kg, SAR
measurement is required for the subsequent next highest measured output power
channel(s) in the initial test configuration until the reported SAR is ≤ 1.2 W/kg or all
required channels are tested.
13. For WLAN, 5.2ac(80)/5.3ac(80)/5.6ac(80) is chosen to be the initial test
configurations.
14. For WLAN, since the highest reported SAR for the initial test configuration is
adjusted by the ratio of the subsequent test configuration to initial test
configuration specified maximum output power and the adjusted SAR is≦1.2 W/kg,
SAR is not required for subsequent test configurations.
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 17 of 130
Other
15. BT and WLAN use the same antenna path and Bluetooth can’t transmit
simultaneously with WLAN.
16. According to KDB447498D01v06, testing of other required channels is not
required when the reported 1-g SAR for the highest output channel is ≤ 0.8 W/kg,
when the transmission band is ≤ 100MHz.
17. According to KDB865664D01v01r04, SAR measurement variability must be
assessed for each frequency band. When the original highest measured SAR is ≥
0.8 W/kg, repeated that measurement once. Perform a second repeated
measurement only if the ratio of largest to smallest SAR for the original and first
repeated measurements is > 1.20 or when the original or repeated measurement
is ≥ 1.45 W/kg (~ 10% from the 1-g SAR limit)
18. According to KDB447498D01v06 – The 1-g and 10-g SAR test exclusion
thresholds for 100 MHz to 6 GHz at test separation distances≤ 50 mm are
determined by: [(max. power of channel, including tune-up tolerance, mW)/(min.
test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for product
specific 10-g SAR.
mode
position
BT
body-worn
max. power max. power
(dB)
(mW)
10
10
f(GHz)
calculation
2.48
1.575
SAR
exclusion
threshold
SAR test
exclusion
Yes
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 18 of 130
1.6 Positioning Procedure
Head SAR measurement statement
Phone position 1, “cheek” or “touch” position. The reference points for the right ear
(RE), left ear (LE) and mouth (M), which define the reference plane for phone
positioning.
Phone position 2, “tilted position.” The reference points for the right ear (RE), left ear
(LE) and mouth (M), which define the reference plane for phone positioning.
Cheek/Touch Position:
The handset was brought toward the mouth of the head phantom by pivoting against
the ear reference point until any point of the mouthpiece or keypad touched the
phantom.
Ear/Tilt Position:
With the phone aligned in the Cheek/Touch position, the handset was tilted away from
the mouth with respect to the test device reference point by 15 degrees.
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 19 of 130
Body SAR measurement statement
1. Body-worn exposure: 10mm
Body-worn accessory exposure is typically related to voice mode operations when
handsets are carried in body-worn accessories. The body-worn accessory
procedures in KDB Publication 447498 D01 should be used to test for body-worn
accessory SAR compliance, without a headset connected to it. When the same
wireless transmission configuration is used for testing body-worn accessory and
hotspot mode SAR, respectively, in voice and data mode, SAR results for the most
conservative test separation distance configuration may be used to support both
SAR conditions. When the reported SAR for a body-worn accessory, measured
without a headset connected to the handset, is > 1.2 W/kg, the highest reported
SAR configuration for that wireless mode and frequency band should be repeated
for the body-worn accessory with a headset attached to the handset.
2. Hotspot exposure: 10mm
A test separation distance of 10 mm is required between the phantom and all
surfaces and edges with a transmitting antenna located within 25 mm from that
surface or edge when the form factor of a handset is larger than 9 cm × 5 cm,
Test configurations of WWAN
(1) Front side
(2) Back side
(3) Bottom side.
(4) Right side.
(5) Left side.
Test configurations of WLAN
(1) Front side
(2) Back side
(3) Top side.
(4) Left side
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 20 of 130
1.7 Evaluation Procedures
The entire evaluation of the spatial peak values is performed within the
Post-processing engine (SEMCAD). The system always gives the maximum values
for the 1 g and 10 g cubes. The algorithm to find the cube with highest averaged SAR
is divided into the following stages:
1. The extraction of the measured data (grid and values) from the Zoom Scan.
2. The calculation of the SAR value at every measurement point based on all stored
data (A/D values and measurement parameters).
3. The generation of a high-resolution mesh within the measured volume.
4. The interpolation of all measured values from the measurement grid to the
high-resolution grid.
5. The extrapolation of the entire 3-D field distribution to the phantom surface over
the distance from sensor to surface.
6. The calculation of the averaged SAR within masses of 1g and 10g.
The probe is calibrated at the center of the dipole sensors that is located 1 to 2.7mm
away from the probe tip. During measurements, the probe stops shortly above the
phantom surface, depending on the probe and the surface detecting system. Both
distances are included as parameters in the probe configuration file. The software
always knows exactly how far away the measured point is from the surface. As the
probe cannot directly measure at the surface, the values between the deepest
measured point and the surface must be extrapolated. The angle between the probe
axis and the surface normal line is less than 30 degree.
In the Area Scan, the gradient of the interpolation function is evaluated to find all the
extreme of the SAR distribution. The uncertainty on the locations of the extreme is
less than 1/20 of the grid size. Only local maximum within –2 dB of the global
maximum are searched and passed for the Cube Scan measurement. In the Cube
Scan, the interpolation function is used to extrapolate the Peak SAR from the lowest
measurement points to the inner phantom surface (the extrapolation distance). The
uncertainty increases with the extrapolation distance. To keep the uncertainty within
1% for the 1 g and 10 g cubes, the extrapolation distance should not be larger than
5mm.
The maximum search is automatically performed after each area scan measurement.
It is based on splines in two or three dimensions. The procedure can find the
maximum for most SAR distributions even with relatively large grid spacing. After the
area scanning measurement, the probe is automatically moved to a position at the
interpolated maximum. The following scan can directly use this position for reference,
e.g., for a finer resolution grid or the cube evaluations. The 1g and 10g peak
evaluations are only available for the predefined cube 7x7x7 scans.
The routines are verified and optimized for the grid dimensions used in these cube
measurements. The measured volume of 30x30x30mm contains about 30g of tissue.
The first procedure is an extrapolation (incl. Boundary correction) to get the points
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 21 of 130
between the lowest measured plane and the surface. The next step uses 3D
interpolation to get all points within the measured volume. In the last step, a 1g cube is
placed numerically into the volume and its averaged SAR is calculated. This cube is
the moved around until the highest averaged SAR is found.
If the highest SAR is found at the edge of the measured volume, the system will issue
a warning: higher SAR values might be found outside of the measured volume. In that
case the cube measurement can be repeated, using the new interpolated maximum
as the center.
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 22 of 130
1.8 Probe Calibration Procedures
For the calibration of E-field probes in lossy liquids, an electric field with an accurately
known field strength must be produced within the measured liquid. For
standardization purposes it would be desirable if all measurements which are
necessary to assess the correct field strength would be traceable to standardized
measurement procedures. In the following two different calibration techniques are
summarized:
1.8.1 Transfer Calibration with Temperature Probes
In lossy liquids the specific absorption rate (SAR) is related both to the electric
field (  ) and the temperature gradient ( T /  t ) in the liquid.
SAR 



c
T
t
Whereby σ is the conductivity, ρ the density and c the heat capacity of the liquid.
Hence, the electric field in lossy liquid can be measured indirectly by measuring
the temperature gradient in the liquid. Non-disturbing temperature probes
(optical probes or thermistor probes with resistive lines) with high spatial
resolution (<1-2 mm) and fast reaction time (<1 s) are available and can be
easily calibrated with high precision [1]. The setup and the exciting source have
no influence on the calibration; only the relative positioning uncertainties of the
standard temperature probe and the E-field probe to be calibrated must be
considered. However, several problems limit the available accuracy of probe
calibrations with temperature probes:
1. The temperature gradient is not directly measurable but must be evaluated
from temperature measurements at different time steps. Special precaution is
necessary to avoid measurement errors caused by temperature gradients due
to energy equalizing effects or convection currents in the liquid. Such effects
cannot be completely avoided, as the measured field itself destroys the
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 23 of 130
thermal equilibrium in the liquid. With a careful setup these errors can be kept
small.
2. The measured volume around the temperature probe is not well defined. It is
difficult to calculate the energy transfer from a surrounding gradient
temperature field into the probe. These effects must be considered, since
temperature probes are calibrated in liquid with homogeneous temperatures.
There is no traceable standard for temperature rise measurements.
3. The calibration depends on the assessment of the specific density, the heat
capacity and the conductivity of the medium. While the specific density and
heat capacity can be measured accurately with standardized procedures (~
2% for c; much better for ρ), there is no standard for the measurement of the
conductivity. Depending on the method and liquid, the error can well exceed
±5%.
4. Temperature rise measurements are not very sensitive and therefore are
often performed at a higher power level than the E-field measurements. The
nonlinearities in the system (e.g., power measurements, different components,
etc.) must be considered.
Considering these problems, the possible accuracy of the calibration of E-field
probes with temperature gradient measurements in a carefully designed setup is
about ±10% (RSS) [2]. Recently, a setup which is a combination of the
waveguide techniques and the thermal measurements was presented in [3]. The
estimated uncertainty of the setup is ±5% (RSS) when the same liquid is used for
the calibration and for actual measurements and ±7-9% (RSS) when not, which
is in good agreement with the estimates given in [2].
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 24 of 130
1.8.2 Calibration with Analytical Fields
In this method a technical setup is used in which the field can be calculated
analytically from measurements of other physical magnitudes (e.g., input power).
This corresponds to the standard field method for probe calibration in air;
however, there is no standard defined for fields in lossy liquids.
When using calculated fields in lossy liquids for probe calibration, several points
must be considered in the assessment of the uncertainty:
1. The setup must enable accurate determination of the incident power.
2. The accuracy of the calculated field strength will depend on the assessment
of the dielectric parameters of the liquid.
3. Due to the small wavelength in liquids with high permittivity, even small setups
might be above the resonant cutoff frequencies. The field distribution in the
setup must be carefully checked for conformity with the theoretical field
distribution.
References
(1) N. Kuster, Q. Balzano, and J.C. Lin, Eds., Mobile Communications Safety,
Chapman & Hall, London, 1997.
(2) K. Meier, M. Burkhardt, T. Schmid, and N. Kuster, \Broadband calibration of
E-field probes in lossy media", IEEE Transactions on Microwave Theory and
Techniques, vol. 44, no. 10, pp. 1954{1962, Oct. 1996.
(3) K. Jokela, P. Hyysalo, and L. Puranen, \Calibration of specific absorption
rate (SAR) probes in waveguide at 900 MHz", IEEE Transactions on
Instrumentation and Measurements, vol. 47, no. 2, pp. 432{438, Apr. 1998.
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 25 of 130
1.9 The SAR Measurement System
A block diagram of the SAR measurement system is given in Fig. a. This SAR
measurement system uses a Computer-controlled 3-D stepper motor system (SPEAG
DASY 5 professional system). Model EX3DV4 field probes are used to determine the
internal electric fields. The SAR can be obtained from the equation SAR= σ (|Ei|2)/ ρ
where σ and ρ are the conductivity and mass density of the tissue-simulant.
Fig. a A block diagram of the SAR measurement system
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 26 of 130
The DASY 5 system for performing compliance tests consists of the following items:
1. A standard high precision 6-axis robot (Staubli RX family) with controller, teach
pendant and software. An arm extension is for accommodating the data acquisition
electronics (DAE).
2. A dosimetric probe, i.e., an isotropic E-field probe optimized and calibrated for
usage in tissue simulating liquid. The probe is equipped with an optical surface
detector system.
3. Data acquisition electronics (DAE) which performs the signal amplification, signal
multiplexing, AD-conversion, offset measurements, mechanical surface detection,
collision detection, etc. The unit is battery powered with standard or rechargeable
batteries. The signal is optically transmitted to the EOC.
4. The Electro-optical converter (EOC) performs the conversion between optical and
electrical of the signals for the digital communication to the DAE and for the analog
signal from the optical surface detection. The EOC is connected to the
measurement server.
5. The function of the measurement server is to perform the time critical tasks such as
signal filtering, control of the robot operation and fast movement interrupts.
6. A probe alignment unit which improves the (absolute) accuracy of the probe
positioning.
7. A computer operating Windows7
8. DASY 5 software.
9. Remote control with teach pendant and additional circuitry for robot safety such as
warning lamps, etc.
10. The SAM twin phantom enabling testing left-hand and right-hand usage.
11. The device holder for handheld mobile phones.
12. Tissue simulating liquid mixed according to the given recipes.
13. Validation dipole kits allowing to validate the proper functioning of the system.
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 27 of 130
1.10 System Components
EX3DV4 E-Field Probe
Construction Symmetrical design with triangular core
Built-in shielding against static charges
PEEK enclosure material (resistant to
organic solvents, e.g., DGBE)
Calibration
Basic Broad Band Calibration in air
Conversion Factors (CF) for
HSL835/1900/2450/5200/5300/5600MHz
Additional CF for other liquids and
frequencies upon request
Frequency
10 MHz to > 6 GHz, Linearity: ± 0.6 dB
Directivity
± 0.3 dB in HSL (rotation around probe axis)
± 0.5 dB in tissue material (rotation normal to probe axis)
Dynamic
Range
10 µW/g to > 100 mW/g
Linearity: ± 0.2 dB (noise: typically < 1 µW/g)
Dimensions Tip diameter: 2.5 mm
Application High precision dosimetric measurements in any exposure scenario
(e.g., very strong gradient fields). Only probe which enables
compliance testing for frequencies up to 6 GHz with precision of
better 30%.
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 28 of 130
SAM PHANTOM V4.0C
Construction: The shell corresponds to the specifications of the Specific
Anthropomorphic Mannequin (SAM) phantom defined in IEEE 1528
and IEC 62209.
It enables the dosimetric evaluation of left and right hand phone
usage as well as body mounted usage at the flat phantom region. A
cover prevents evaporation of the liquid. Reference markings on the
phantom allow the complete setup of all predefined phantom
positions and measurement grids by manually teaching three points
with the robot.
Shell
Thickness:
2 ± 0.2 mm
Filling
Volume:
Approx. 25 liters
Dimensions:
Height: 850 mm;
Length: 1000 mm;
Width: 500 mm
DEVICE HOLDER
Construction In combination with the Twin SAM Phantom
V4.0/V4.0C or Twin SAM, the Mounting
Device (made from POM) enables the
rotation of the mounted transmitter in
spherical coordinates, whereby the rotation
point is the ear opening. The devices can
be easily and accurately positioned
according to IEC, IEEE, CENELEC, FCC or
other specifications. The device holder can
be locked at different phantom locations
(left head, right head, flat phantom).
Device Holder
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 29 of 130
1.11 SAR System Verification
The microwave circuit arrangement for system verification is sketched in Fig. b. The
daily system accuracy verification occurs within the flat section of the SAM phantom.
A SAR measurement was performed to see if the measured SAR was within +/- 10%
(according to KDB865664D01v01r04) from the target SAR values.
These tests were done at 835/1900/2450/5200/5300/5600 MHz. The tests were
conducted on the same days as the measurement of the DUT. The obtained results
from the system accuracy verification are displayed in the table 1. During the tests,
the ambient temperature of the laboratory was 21.7°C, the relative humidity was 62%
and the liquid depth above the ear reference points was above 15 cm (≤3G) or 10 cm
(>3G) in all the cases. It is seen that the system is operating within its specification,
as the results are within acceptable tolerance of the reference values.
Fig. b The block diagram of system verification
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 30 of 130
Frequency
(MHz)
Validation
Kit
S/N
D835V2
4d063
D1900V2
5d027 1900
D2450V2
727
835
2450
5200
D5GHzV2
1023
5300
5600
Head
Body
Head
Body
Head
Body
Head
Body
Head
Body
Head
Body
1W Target
SAR-1g
(mW/g)
Measured
SAR-1g
(mW/g)
9.40
9.57
38.7
39.7
51.0
49.6
77.0
71.9
79.9
75.1
82.6
78.3
2.33
2.56
9.56
10.10
12.9
12.1
7.71
7.53
8.28
7.78
8.4
8.13
Measured
Deviation
Measured
SAR-1g
(%)
Date
normalized to
1W (mW/g)
9.32
-0.85% Nov. 22, 2016
10.24
7.00%
Nov. 24, 2016
38.24
-1.19% Nov. 22, 2016
40.4
1.76%
Nov. 24, 2016
51.6
1.18%
Nov. 22, 2016
48.4
-2.42% Nov. 25, 2016
77.1
0.13%
Nov. 23, 2016
75.3
4.73%
Nov. 25, 2016
82.8
3.63%
Nov. 23, 2016
77.8
3.60%
Nov. 25, 2016
84
1.69%
Nov. 23, 2016
81.3
3.83%
Nov. 25, 2016
Table 1. Results of system validation
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 31 of 130
1.12 Tissue Simulant Fluid for the Frequency Band
The dielectric properties for this Head-simulant fluid were measured by using the
Agilent Model 85070E Dielectric Probe (rates frequency band 200 MHz to 20 GHz)
in conjunction with Network Analyzer.
All dielectric parameters of tissue simulates were measured within 24 hours of
SAR measurements. The depth of the tissue simulant in the flat section of the
phantom was at least 15 cm (≤3G) or 10 cm (>3G) during all tests. (Appendix Fig.
2)
Target
Measured
Measured
Target
Measured
Tissue
Dielectric
Dielectric
Frequency
Conductivity,
Conductivity,
Type
Constant,
Constant,
(MHz)
σ (S/m)
σ (S/m)
εr
εr
835
41.500
0.900
41.181
0.882
846.6
41.500
0.912
41.038
0.894
848.8
41.500
0.915
41.013
0.896
1850.2
40.000
1.400
40.207
1.378
1900
40.000
1.400
40.087
1.429
2437
39.223
1.788
38.236
1.813
2450
39.200
1.800
38.213
1.826
Head
5200
35.986
4.655
35.052
4.726
5210
35.974
4.665
34.976
4.737
5290
35.883
4.747
34.465
4.858
5300
35.871
4.758
34.453
4.869
5600
35.529
5.065
34.406
5.213
5690
35.426
5.157
34.303
5.303
835
55.200
0.970
53.336
0.996
836.6
55.195
0.972
53.331
0.997
846.6
55.164
0.984
53.299
1.007
848.8
55.158
0.987
53.194
1.021
1850.2
53.300
1.520
52.089
1.507
1900
53.300
1.520
51.961
1.563
1909.8
53.300
1.520
51.935
1.573
2402
52.764
1.904
52.672
1.910
Body
2437
52.717
1.938
52.590
1.961
2450
52.700
1.950
52.573
1.974
5200
49.014
5.299
48.387
5.333
5210
49.001
5.311
48.372
5.343
5290
48.892
5.404
48.258
5.427
5300
48.879
5.416
48.245
5.441
5600
48.471
5.766
48.772
5.868
5690
48.349
5.872
48.649
5.974
% dev εr
% dev σ
0.77%
1.11%
1.17%
-0.52%
-0.22%
2.52%
2.52%
2.59%
2.77%
3.95%
3.95%
3.16%
3.17%
3.38%
3.38%
3.38%
3.56%
2.27%
2.51%
2.56%
0.17%
0.24%
0.24%
1.28%
1.28%
1.30%
1.30%
-0.62%
-0.62%
2.00%
2.03%
2.06%
1.57%
-2.07%
-1.37%
-1.44%
-1.53%
-1.54%
-2.33%
-2.34%
-2.92%
-2.83%
-2.68%
-2.58%
-2.31%
-3.45%
0.86%
-2.83%
-3.49%
-0.31%
-1.21%
-1.23%
-0.64%
-0.60%
-0.42%
-0.46%
-1.76%
-1.75%
Measurement
Date
2016/11/22
2016/11/23
2016/11/24
2016/11/25
Table 2. Dielectric Parameters of Tissue Simulant Fluid
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 32 of 130
The composition of the tissue simulating liquid:
Frequency
Mode
(MHz)
DGMBE
850
1900
2450
─
Head
Ingredient
Total
Preventol
Water
Salt
Cellulose Sugar amount
D-7
532.98 g 18.3 g
2.4 g
3.2 g
766 g 1.3L(Kg)
1.2 g
─
─
─
─
1.0L(Kg)
─
─
─
1.0L(Kg)
─
─
─
─
1.0L(Kg)
─
─
─
─
1.0L(Kg)
631.68 g 11.72 g
─
Head 444.52 g 552.42 g 3.06 g
Body 300.67 g 716.56 g 4.0 g
Body
550ml
Head
450ml
Body 301.7ml 698.3ml
600 g 1.0L(Kg)
Simulating Liquids for 5 GHz, Manufactured by SPEAG:
Ingredients
Water
Esters, Emulsifiers, Inhibitors Sodium and Salt
(% by weight)
60-80
20-40
0-1.5
Table 3. Recipes for tissue simulating liquid
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 33 of 130
1.13 Test Standards and Limits
According to FCC 47CFR §2.1093(d) The limits to be used for evaluation are
based generally on criteria published by the American National Standards Institute
(ANSI) for localized specific absorption rate (‘‘SAR’’) in Section 4.2 of ‘‘IEEE
Standard for Safety Levels with Respect to Human Exposure to Radio Frequency
Electromagnetic Fields, 3 kHz to 300 GHz,’’ ANSI/IEEE C95.1, By the Institute of
Electrical and Electronics Engineers, Inc., New York, New York 10017.
These criteria for SAR evaluation are similar to those recommended by the
National Council on Radiation Protection and Measurements (NCRP) in
‘‘Biological Effects and Exposure Criteria for Radio frequency Electromagnetic
Fields,’’ NCRP Report No. 86, Section 17.4.5. Copyright NCRP, 1986, Bethesda,
Maryland 20814. SAR is a measure of the rate of energy absorption due to
exposure to an RF transmitting source. SAR values have been related to
threshold levels for potential biological hazards. The criteria to be used are
specified in paragraphs (d)(1) and (d)(2) of this section and shall apply for portable
devices transmitting in the frequency range from 100 kHz to 6 GHz. Portable
devices that transmit at frequencies above 6 GHz are to be evaluated in terms of
the MPE limits specified in § 1.1310 of this chapter.
Measurements and calculations to demonstrate compliance with MPE field
strength or power density limits for devices operating above 6 GHz should be
made at a minimum distance of 5 cm from the radiating source.
1. Limits for Occupational/Controlled exposure: 0.4 W/kg as averaged over the
whole-body and spatial peak SAR not exceeding 8 W/kg as averaged over any
1 gram of tissue (defined as a tissue volume in the shape of a cube).
Exceptions are the hands, wrists, feet and ankles where the spatial peak SAR
shall not exceed 20 W/kg, as averaged over a 10 grams of tissue (defined as a
tissue volume in the shape of a cube).
Occupational/Controlled limits apply when persons are exposed as a
consequence of their employment provided these persons are fully aware of and
exercise control over their exposure. Awareness of exposure can be
accomplished by use of warning labels or by specific training or education through
appropriate means, such as an RF safety program in a work environment.
2. Limits for General Population/Uncontrolled exposure: 0.08 W/kg as averaged
over the whole-body and spatial peak SAR not exceeding 1.6 W/kg as
averaged over any 1 gram of tissue (defined as a tissue volume in the shape of
a cube).
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 34 of 130
Exceptions are the hands, wrists, feet and ankles where the spatial peak SAR
shall not exceed 4 W/kg, as averaged over any 10 grams of tissue (defined as a
tissue volume in the shape of a cube).
General Population/Uncontrolled limits apply when the general public may be
exposed, or when persons that are exposed as a consequence of their
employment may not be fully aware of the potential for exposure or do not
exercise control over their exposure.
Warning labels placed on consumer devices such as cellular telephones will not
be sufficient reason to allow these devices to be evaluated subject to limits for
occupational/controlled exposure in paragraph (d)(1) of this section.(Table .6)
Human Exposure
Spatial Peak SAR
(Brain)
Spatial Average SAR
(Whole Body)
Spatial Peak SAR
(Hands/Feet/Ankle/Wrist)
Uncontrolled Environment
General Population
Controlled Environment
Occupational
1.60 W/kg
8.00 W/kg
0.08 W/kg
0.40 W/kg
4.00 W/kg
20.00 W/kg
Table 4. RF exposure limits
Notes:
1. Uncontrolled environments are defined as locations where there is potential exposure of
individuals who have no knowledge or control of their potential exposure.
2. Controlled environments are defined as locations where there is potential exposure of
individuals who have knowledge of their potential exposure and can exercise control
over their exposure.
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 35 of 130
2. Summary of Results
GSM 850 MHz
Mode
GSM850
(Head)
GSM850
(Body-Worn)
GPRS850
(Hotspot)
(1Dn2UP)
Position
Distanc
(mm)
Re Cheek
Re Tilt
Averaged SAR over
Measured
1g
Plot
Avg.
Scaling
(W/kg)
page
Power
(dBm)
Measured Reported
32.42
14.29% 0.114
0.130
46
CH
Freq.
(MHz)
Max. Rated Avg.
Power + Max.
Tolerance (dBm)
251
848.8
33.00
251
848.8
33.00
32.42
14.29%
0.046
0.053
Le Cheek
251
848.8
33.00
32.42
14.29%
0.090
0.103
Le Tilt
251
848.8
33.00
32.42
14.29%
0.056
0.064
Front side
10
251
848.8
33.00
32.42
14.29%
0.193
0.221
47
Back side
10
251
848.8
33.00
32.42
14.29%
0.571
0.653
Front side
10
251
848.8
30.00
29.43
14.02%
0.190
0.217
Back side
10
251
848.8
30.00
29.43
14.02%
0.554
0.632
48
Bottom side
10
251
848.8
30.00
29.43
14.02%
0.234
0.267
Right side
10
251
848.8
30.00
29.43
14.02%
0.141
0.161
Left side
10
251
848.8
30.00
29.43
14.02%
0.047
0.054
Position
Distanc
(mm)
CH
Freq.
(MHz)
Max. Rated Avg.
Power + Max.
Tolerance (dBm)
Re Cheek
512
1850.2
30.00
Re Tilt
512
1850.2
30.00
29.19
20.50%
0.092
0.111
Le Cheek
512
1850.2
30.00
29.19
20.50%
0.310
0.374
49
Le Tilt
512
1850.2
30.00
29.19
20.50%
0.099
0.119
Front side
10
512
1850.2
30.00
29.19
20.50%
0.297
0.358
Back side
10
512
1850.2
30.00
29.19
20.50%
0.502
0.605
50
GSM 1900 MHz
Mode
GSM1900
(Head)
GSM1900
(Body-Worn)
GPRS1900
(Hotspot)
(1Dn4UP)
Averaged SAR over
Measured
1g
Avg.
Plot
Scaling
(W/kg)
Power
page
(dBm)
Measured Reported
29.19
20.50% 0.166
0.200
Front side
10
810
1909.8
24.00
23.50
12.20%
0.309
0.347
Back side
10
810
1909.8
24.00
23.50
12.20%
0.399
0.448
51
Bottom side
10
810
1909.8
24.00
23.50
12.20%
0.210
0.236
Right side
10
810
1909.8
24.00
23.50
12.20%
0.012
0.013
Left side
10
810
1909.8
24.00
23.50
12.20%
0.187
0.210
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 36 of 130
WCDMA Band V
Mode
R99
(Head)
Hotspot
Position
Distanc
(mm)
RE Cheek
CH
Freq.
(MHz)
Max. Rated Avg.
Power + Max.
Tolerance (dBm)
4233
846.6
24.5
Averaged SAR over
Measured
1g
Plot
Avg.
Scaling
(W/kg)
page
Power
(dBm)
Measured Reported
24.32
4.23%
0.182
0.190
52
RE Tilt
4233
846.6
24.5
24.32
4.23%
0.070
0.073
LE Cheek
4233
846.6
24.5
24.32
4.23%
0.127
0.132
LE Tilt
4233
846.6
24.5
24.32
4.23%
0.086
0.090
Front side
10
4233
846.6
24.5
24.32
4.23%
0.293
0.305
Back side
10
4132
826.4
24.5
23.73
19.40%
0.755
0.901
Back side
10
4183
836.6
24.5
23.93
14.02%
0.760
0.867
Back side
10
4233
846.6
24.5
24.32
4.23%
0.802
0.836
53
Back side*
10
4233
846.6
24.5
24.32
4.23%
0.800
0.834
Bottom side
10
4233
846.6
24.5
24.32
4.23%
0.329
0.343
Right side
10
4233
846.6
24.5
24.32
4.23%
0.232
0.242
Left side
10
4233
846.6
24.5
24.32
4.23%
0.074
0.077
* - repeated at the highest SAR measurement according to the KDB865664D01v01r04
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 37 of 130
WLAN802.11 b
Mode
WLAN
802.11 b
(Head)
Hotspot
Max. Rated Measured
Avg.
Avg.
Power + Max.
Power
Tolerance
(dBm)
(dBm)
13.5
12.22
Averaged SAR over 1g
Plot
(W/kg)
page
Measured Reported
Position
Distance
(mm)
CH
Freq.
(MHz)
RE Cheek
2437
134.28%
0.032
0.043
RE Tilt
2437
13.5
12.22
134.28%
0.026
0.035
LE Cheek
2437
13.5
12.22
134.28%
0.065
0.087
54
LE Tilt
2437
13.5
12.22
134.28%
0.045
0.060
Front side
10
2437
13.5
12.22
134.28%
0.017
0.023
Back side
10
2437
13.5
12.22
134.28%
0.057
0.077
55
Top side
10
2437
13.5
12.22
134.28%
0.020
0.027
Left side
10
2437
13.5
12.22
134.28%
0.004
0.006
Scaling
Bluetooth
Mode
Bluetoot
(GFSK)
(Bodyworn)
Max. Rated Measured
Avg.
Avg.
Power + Max.
Power
Tolerance
(dBm)
(dBm)
Averaged SAR over 1g
Plot
(W/kg)
page
Measured Reported
Position
Distance
(mm)
CH
Freq.
(MHz)
Front side
10
2402
10
8.91
128.53%
0.005
0.006
Back side
10
2402
10
8.91
128.53%
0.019
0.024
56
Scaling
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 38 of 130
WLAN802.11 ac(80M) 5.2G
Max. Rated Measured
Avg.
Avg.
Power + Max.
Power
Tolerance
(dBm)
(dBm)
13
12.39
Averaged SAR over 1g
Plot
(W/kg)
page
Measured Reported
Mode
Position
Distance
(mm)
CH
Freq.
(MHz)
WLAN
802.11
ac(80M)
5.2G
(Head)
RE Cheek
42
5210
115.08%
0.098
0.113
RE Tilt
42
5210
13
12.39
115.08%
0.075
0.086
LE Cheek
42
5210
13
12.39
115.08%
0.135
0.155
57
LE Tilt
42
5210
13
12.39
115.08%
0.086
0.099
Bodyworn
Front side
10
42
5210
13
12.39
115.08%
0.020
0.023
Back side
10
42
5210
13
12.39
115.08%
0.072
0.083
58
Scaling
WLAN802.11 ac(80M) 5.3G
Max. Rated Measured
Averaged SAR over 1g
Avg.
Avg.
Plot
(W/kg)
Scaling
Power + Max.
Power
page
Tolerance
(dBm)
Measured Reported
(dBm)
13
12.46
113.24%
0.065
0.074
Mode
Position
Distance
(mm)
CH
Freq.
(MHz)
WLAN
802.11
ac(80M)
5.3G
(Head)
RE Cheek
58
5290
RE Tilt
58
5290
13
12.46
113.24%
0.056
LE Cheek
58
5290
13
12.46
113.24%
LE Tilt
58
5290
13
12.46
113.24%
Bodyworn
Front side
10
58
5290
13
12.46
113.24%
0.020
0.023
Back side
10
58
5290
13
12.46
113.24%
0.059
0.067
60
0.063
0.098
0.111
59
0.077
0.087
WLAN802.11 ac(80M) 5.6G
Distance
(mm)
CH
Freq.
(MHz)
Max. Rated Measured
Averaged SAR over 1g
Avg.
Plot
Avg.
(W/kg)
Scaling
Power + Max.
page
Power
Tolerance
(dBm)
Measured Reported
(dBm)
12.5
11.82
116.95%
0.088
0.103
Mode
Position
WLAN
802.11
ac(80M)
5.6G
(Head)
RE Cheek
138
5690
RE Tilt
138
5690
12.5
11.82
116.95%
0.085
0.099
LE Cheek
138
5690
12.5
11.82
116.95%
0.065
0.076
LE Tilt
138
5690
12.5
11.82
116.95%
0.095
0.111
61
Bodyworn
Front side
10
138
5690
12.5
11.82
116.95%
0.020
0.023
Back side
10
138
5690
12.5
11.82
116.95%
0.027
0.032
62
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 39 of 130
3. Simultaneous Transmission Analysis
Simultaneous Transmission Scenarios:
Simultaneous Transmit Configurations
Head
Body-Worn
Hotspot
GSM + 2.4GHz Wi-Fi
Yes
Yes
No
GPRS + 2.4GHz Wi-Fi
No
No
Yes
WCDMA + 2.4GHz Wi-Fi
Yes
Yes
Yes
GSM + 5GHz Wi-Fi
Yes
Yes
No
GPRS + 5GHz Wi-Fi
No
No
No
WCDMA + 5GHz Wi-Fi
Yes
Yes
No
GSM + BT
No
Yes
No
GPRS + BT
No
No
No
WCDMA + BT
No
Yes
No
Notes:
1. WiFi and BT can't transmit simultaneously.
2. The device does not support DTM function. Body-worn accessory testing is typically
associated with voice operations. Therefore, GSM voice was evaluated for body-worn SAR.
3.Based on KDB447498D01 note 36, when SAR test exclusion is allowed by other published RF
exposure KDB procedures, such as the 2.5 cm hotspot mode SAR test exclusion for an edge or
surface, then estimated SAR is not required to determine simultaneous SAR test exclusion.
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 40 of 130
3.1 Estimated SAR calculation
According to KDB447498 D01v05 – When standalone SAR test exclusion applies
to an antenna that transmits simultaneously with other antennas, the standalone
SAR must be estimated according to following to determine simultaneous
transmission SAR test exclusion:
If the minimum test separation distance is < 5mm, a distance of 5mm is used for
estimated SAR calculation. When the test separation distance is >50mm, the
0.4W/kg is used for SAR-1g.
3.2 SPLSR evaluation and analysis
Per KDB447498D01, when the sum of SAR is larger than the limit, SAR test
exclusion is determined by the SAR sum to peak location separation ratio(SPLSR).
The simultaneous transmitting antennas in each operating mode and exposure
condition combination must be considered one pair at a time to determine the SAR
to peak location separation ratio to qualify for test exclusion.
The ratio is determined by (SAR1 + SAR2)^1.5/Ri, rounded to two decimal digits,
and must be ≤ 0.04 for all antenna pairs in the configuration to qualify for 1-g SAR
test exclusion.
SAR1 and SAR2 are the highest reported or estimated SAR for each antenna in the
pair, and Ri is the separation distance between the peak SAR locations for the
antenna pair in mm.
When standalone test exclusion applies, SAR is estimated; the peak location is
assumed to be at the feed-point or geometric center of the antenna.
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 41 of 130
Simultaneous Transmission Combination
reported SAR WWAN and WLAN 2.4GHz, ΣSAR evaluation
Frequency
band
GSM 850
GPRS 850
(1Dn2UP)
GSM 1900
Position
reported SAR / W/kg
ΣSAR
WWAN
WLAN
<1.6W/kg
Right cheek
0.130
0.043
0.173
Right tilt
0.053
0.035
0.088
Left cheek
0.103
0.087
0.190
Head
Left tilt
0.064
0.060
0.124
Front
0.217
0.023
0.240
Back
0.632
0.077
0.709
Top
0.027
Bottom
0.267
Right
0.161
Left
0.054
0.006
0.060
Right cheek
0.200
0.043
0.243
Right tilt
0.111
0.035
0.146
Left cheek
0.374
0.087
0.461
Hotspot
Head
Left tilt
0.119
0.060
0.179
Front
0.347
0.023
0.370
Back
0.448
0.077
0.525
Top
0.027
Bottom
0.236
Right
0.013
Left
0.210
0.006
0.216
Right cheek
0.190
0.043
0.233
Right tilt
0.073
0.035
0.108
Left cheek
0.132
0.087
0.219
Left tilt
0.090
0.060
0.150
Front
0.305
0.023
0.328
Back
0.901
0.077
0.978
Top
0.027
Bottom
0.343
Right
0.242
Left
0.077
0.006
0.083
GPRS 1900
Hotspot
(1Dn4UP)
Head
WCDMA
Band V
Hotspot
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 42 of 130
reported SAR WWAN and WLAN 2.4GHz, ΣSAR evaluation
Frequency
band
Position
reported SAR / W/kg
WWAN
WLAN
ΣSAR
<1.6W/kg
GSM 850
Bodyworn
Front
0.221
0.023
0.244
Back
0.653
0.077
0.730
GSM 1900
Bodyworn
Front
0.358
0.023
0.381
Back
0.605
0.077
0.682
reported SAR WWAN and WLAN 5GHz, ΣSAR evaluation
Frequency
band
Position
reported SAR / W/kg
ΣSAR
WWAN
WLAN
<1.6W/kg
Right cheek
0.130
0.113
0.243
Right tilt
0.053
0.099
0.152
Left cheek
0.103
0.155
0.258
Left tilt
0.064
0.111
0.175
Front
0.221
0.023
0.244
Back
0.653
0.083
0.736
Right cheek
0.200
0.113
0.313
Right tilt
0.111
0.099
0.210
Left cheek
0.374
0.155
0.529
Left tilt
0.119
0.111
0.230
Front
0.358
0.023
0.381
Back
0.605
0.083
0.688
Right cheek
0.190
0.113
0.303
Right tilt
0.073
0.099
0.172
Left cheek
0.132
0.155
0.287
Left tilt
0.090
0.111
0.201
Front
0.305
0.023
0.328
Back
0.901
0.083
0.984
Head
GSM 850
Bodyworn
Head
GSM 1900
Bodyworn
Head
WCDMA
Band V
Bodyworn
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 43 of 130
reported SAR WWAN and Bluetooth, ΣSAR evaluation
Frequency
band
reported SAR / W/kg
Position
WWAN
ΣSAR
Bluetooth <1.6W/kg
GSM 850
BodyWorn
Front
0.221
0.006
0.227
Back
0.653
0.024
0.677
GSM 1900
BodyWorn
Front
0.358
0.006
0.364
Back
0.605
0.024
0.629
WCDMA
Band V
BodyWorn
Front
0.305
0.006
0.311
Back
0.901
0.024
0.925
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 44 of 130
4. Instruments List
Manufacturer
Device
Type
Serial number
Date of last Date of next
calibration calibration
Schmid &
Dosimetric E-Field
Partner
EX3DV4
Probe
Engineering AG
D835V2
Schmid &
System Validation D1900V2
Partner
Dipole
D2450V2
Engineering AG
3831
Jan.27,2016 Jan.26,2017
4d063
Aug.25,2016 Aug.24,2017
5d027
Apr.25,2016 Apr.24,2017
727
Apr.19,2016 Apr.18,2017
D5GHzV2
1023
Jan.26,2016 Jan.25,2017
547
Mar.21,2016 Mar.20,2017
N/A
Calibration Calibration
not required not required
N/A
Calibration Calibration
not required not required
Schmid &
Data acquisition
Partner
DAE4
Electronics
Engineering AG
Schmid &
DASY 52
Software
Partner
V52.8.8
Engineering AG
Schmid &
Partner
Phantom
SAM
Engineering AG
Agilent
Network Analyzer E5071C
Dielectric
Agilent
85070E
Probe Kit
772D
Dual-directional
Agilent
coupler
778D
MY46107530 Jan.07,2016
Calibration
MY44300677
not required
MY52180142 Apr.13,2016
Jan.06,2017
Calibration
not required
Apr.12,2017
MY52180302 Apr.13,2016 Apr.12,2017
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 45 of 130
Manufacturer
Device
Agilent
RF Signal
Generator
Power Meter
Agilent
Power Sensor
Agilent
TECPEL
Anritsu
Type
Serial number
Date of last Date of next
calibration calibration
N5181A
MY50145142 Feb.19,2016 Feb.18,2017
E4417A
MY51410006 Jan.07,2016 Jan.06,2017
E9301H
MY51470001 Jan.07,2016 Jan.06,2017
E9301H
MY51470002 Jan.07,2016 Jan.06,2017
Digital
DTM-303A TP130073 Feb.26,2016 Feb.25,2017
thermometer
Radio
Communication MT8820C 6201061049 Apr.08,2016 Apr.07,2017
Test
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 46 of 130
5. Measurements
Date: 2016/11/22
GSM 850_Head_Re Cheek_CH 251
Communication System: GSM; Frequency: 848.8 MHz, Duty Cycle: 1:8.3
Medium parameters used: f = 849 MHz; σ = 0.896 S/m; εr = 41.013; ρ = 1000 kg/m3
Phantom section: Right Section
Ambient temperature: 23.4° C ; Liquid temperature: 21.8° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(8.84, 8.84, 8.84); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (71x111x1): Interpolated grid: dx=15 mm, dy=15
mm
Maximum value of SAR (interpolated) = 0.132 W/kg
Configuration/Head/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm,
dy=8mm, dz=5mm
Reference Value = 3.478 V/m; Power Drift = 0.12 dB
Peak SAR (extrapolated) = 0.142 W/kg
SAR(1 g) = 0.114 W/kg; SAR(10 g) = 0.085 W/kg
Maximum value of SAR (measured) = 0.131 W/kg
0 dB = 0.131 W/kg = -8.82 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 47 of 130
Date: 2016/11/24
GSM 850_Body-worn_Back side_CH 251_10mm
Communication System: GSM; Frequency: 848.8 MHz, Duty Cycle: 1:8.3
Medium parameters used: f = 849 MHz; σ = 1.021 S/m; εr = 53.194; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.5° C ; Liquid temperature: 22.0° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(9.08, 9.08, 9.08); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (71x121x1): Interpolated grid: dx=15 mm, dy=15
mm
Maximum value of SAR (interpolated) = 0.786 W/kg
Configuration/Head/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm,
dy=8mm, dz=5mm
Reference Value = 15.06 V/m; Power Drift = 0.08 dB
Peak SAR (extrapolated) = 0.992 W/kg
SAR(1 g) = 0.571 W/kg; SAR(10 g) = 0.316 W/kg
Maximum value of SAR (measured) = 0.797 W/kg
0 dB = 0.797 W/kg = -0.98 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 48 of 130
Date: 2016/11/24
GPRS 850_Hotspot_Back side_CH 251_10mm
Communication System: GPRS (1Dn2Up); Frequency: 848.8 MHz, Duty Cycle: 1:4.15
Medium parameters used: f = 849 MHz; σ = 1.021 S/m; εr = 53.194; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.5° C ; Liquid temperature: 22.0° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(9.08, 9.08, 9.08); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (71x121x1): Interpolated grid: dx=15 mm, dy=15
mm
Maximum value of SAR (interpolated) = 0.761 W/kg
Configuration/Head/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm,
dy=8mm, dz=5mm
Reference Value = 14.79 V/m; Power Drift = 0.09 dB
Peak SAR (extrapolated) = 0.963 W/kg
SAR(1 g) = 0.554 W/kg; SAR(10 g) = 0.307 W/kg
Maximum value of SAR (measured) = 0.775 W/kg
0 dB = 0.775 W/kg = -1.11 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 49 of 130
Date: 2016/11/22
GSM 1900_Head_Le Cheek_CH 512
Communication System: GSM; Frequency: 1850.2 MHz, Duty Cycle: 1:8.3
Medium parameters used: f = 1850.2 MHz; σ = 1.378 S/m; εr = 40.207; ρ = 1000 kg/m3
Phantom section: Left Section
Ambient temperature: 23.1° C ; Liquid temperature: 22.0° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(7.66, 7.66, 7.66); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (61x111x1): Interpolated grid: dx=15 mm, dy=15
mm
Maximum value of SAR (interpolated) = 0.401 W/kg
Configuration/Head/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm,
dy=8mm, dz=5mm
Reference Value = 4.847 V/m; Power Drift = 0.15 dB
Peak SAR (extrapolated) = 0.479 W/kg
SAR(1 g) = 0.310 W/kg; SAR(10 g) = 0.192 W/kg
Maximum value of SAR (measured) = 0.402 W/kg
0 dB = 0.402 W/kg = -3.96 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 50 of 130
Date: 2016/11/24
GSM 1900_Body-worn_Back side_CH 512_10mm
Communication System: GSM; Frequency: 1850.2 MHz, Duty Cycle: 1:8.3
Medium parameters used: f = 1850.2 MHz; σ = 1.507 S/m; εr = 52.089; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.4° C ; Liquid temperature: 22.2° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(7.54, 7.54, 7.54); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (61x131x1): Interpolated grid: dx=15 mm, dy=15
mm
Maximum value of SAR (interpolated) = 0.714 W/kg
Configuration/Head/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm,
dy=8mm, dz=5mm
Reference Value = 7.367 V/m; Power Drift = 0.02 dB
Peak SAR (extrapolated) = 0.854 W/kg
SAR(1 g) = 0.502 W/kg; SAR(10 g) = 0.302 W/kg
Maximum value of SAR (measured) = 0.658 W/kg
0 dB = 0.658 W/kg = -1.82 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 51 of 130
Date: 2016/11/24
GPRS 1900_Hotspot_Back side_CH 810_10mm
Communication System: GPRS (1Dn4Up); Frequency: 1909.8 MHz, Duty Cycle: 1:2
Medium parameters used: f = 1910 MHz; σ = 1.573 S/m; εr = 51.935; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.4° C ; Liquid temperature: 22.2° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(7.54, 7.54, 7.54); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (61x131x1): Interpolated grid: dx=15 mm, dy=15
mm
Maximum value of SAR (interpolated) = 0.586 W/kg
Configuration/Head/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm,
dy=8mm, dz=5mm
Reference Value = 5.658 V/m; Power Drift = -0.02 dB
Peak SAR (extrapolated) = 0.651 W/kg
SAR(1 g) = 0.399 W/kg; SAR(10 g) = 0.249 W/kg
Maximum value of SAR (measured) = 0.525 W/kg
0 dB = 0.525 W/kg = -2.80 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 52 of 130
Date: 2016/11/22
WCDMA Band V_Head_Re Cheek_CH 4233
Communication System: WCDMA; Frequency: 846.6 MHz, Duty Cycle: 1:1
Medium parameters used: f = 847 MHz; σ = 0.894 S/m; εr = 41.038; ρ = 1000 kg/m3
Phantom section: Right Section
Ambient temperature: 23.4° C ; Liquid temperature: 21.8° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(8.84, 8.84, 8.84); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (71x111x1): Interpolated grid: dx=15 mm, dy=15
mm
Maximum value of SAR (interpolated) = 0.209 W/kg
Configuration/Head/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm,
dy=8mm, dz=5mm
Reference Value = 3.902 V/m; Power Drift = 0.05 dB
Peak SAR (extrapolated) = 0.227 W/kg
SAR(1 g) = 0.182 W/kg; SAR(10 g) = 0.134 W/kg
Maximum value of SAR (measured) = 0.209 W/kg
0 dB = 0.209 W/kg = -6.80 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 53 of 130
Date: 2016/11/24
WCDMA Band V_Hotspot_Back side_CH 4233_10mm
Communication System: WCDMA; Frequency: 846.6 MHz, Duty Cycle: 1:1
Medium parameters used: f = 847 MHz; σ = 1.007 S/m; εr = 53.299; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.5° C ; Liquid temperature: 22.0° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(9.08, 9.08, 9.08); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (71x121x1): Interpolated grid: dx=15 mm, dy=15
mm
Maximum value of SAR (interpolated) = 1.06 W/kg
Configuration/Head/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm,
dy=8mm, dz=5mm
Reference Value = 17.31 V/m; Power Drift = 0.05 dB
Peak SAR (extrapolated) = 1.33 W/kg
SAR(1 g) = 0.802 W/kg; SAR(10 g) = 0.440 W/kg
Maximum value of SAR (measured) = 1.06 W/kg
0 dB = 1.06 W/kg = 0.25 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 54 of 130
Date: 2016/11/22
WLAN 802.11b_Head_Le Cheek_CH 6
Communication System: WLAN(2.4G); Frequency: 2437 MHz, Duty Cycle: 1:1
Medium parameters used: f = 2437 MHz; σ = 1.813 S/m; εr = 38.236; ρ = 1000 kg/m3
Phantom section: Left Section
Ambient temperature: 23.4° C ; Liquid temperature: 22.1° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(6.92, 6.92, 6.92); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (81x141x1): Interpolated grid: dx=12 mm, dy=12
mm
Maximum value of SAR (interpolated) = 0.0978 W/kg
Configuration/Head/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm,
dy=5mm, dz=5mm
Reference Value = 4.149 V/m; Power Drift = 0.09 dB
Peak SAR (extrapolated) = 0.142 W/kg
SAR(1 g) = 0.065 W/kg; SAR(10 g) = 0.032 W/kg
Maximum value of SAR (measured) = 0.0993 W/kg
0 dB = 0.0993 W/kg = -10.03 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 55 of 130
Date: 2016/11/25
WLAN 802.11b_Hotspot_Back side_CH 6_10mm
Communication System: WLAN(2.4G); Frequency: 2437 MHz, Duty Cycle: 1:1
Medium parameters used: f = 2437 MHz; σ = 1.961 S/m; εr = 52.59; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.7° C ; Liquid temperature: 22.0° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(7.05, 7.05, 7.05); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (91x141x1): Interpolated grid: dx=12 mm, dy=12
mm
Maximum value of SAR (interpolated) = 0.0858 W/kg
Configuration/Head/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm,
dy=5mm, dz=5mm
Reference Value = 2.613 V/m; Power Drift = 0.18 dB
Peak SAR (extrapolated) = 0.126 W/kg
SAR(1 g) = 0.057 W/kg; SAR(10 g) = 0.025 W/kg
Maximum value of SAR (measured) = 0.0898 W/kg
0 dB = 0.0898 W/kg = -10.47 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 56 of 130
Date: 2016/11/25
Bluetooth(GFSK)_Body-worn_Back side_CH 0_10mm
Communication System: Bluetooth; Frequency: 2402 MHz, Duty Cycle: 1:1
Medium parameters used: f = 2402 MHz; σ = 1.91 S/m; εr = 52.672; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.7° C ; Liquid temperature: 22.0° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(7.05, 7.05, 7.05); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (91x141x1): Interpolated grid: dx=12 mm, dy=12
mm
Maximum value of SAR (interpolated) = 0.0286 W/kg
Configuration/Head/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm,
dy=5mm, dz=5mm
Reference Value = 1.196 V/m; Power Drift = 0.07 dB
Peak SAR (extrapolated) = 0.0730 W/kg
SAR(1 g) = 0.019 W/kg; SAR(10 g) = 0.0085 W/kg
Maximum value of SAR (measured) = 0.0316 W/kg
0 dB = 0.0316 W/kg = -15.00 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 57 of 130
Date: 2016/11/23
WLAN 802.11ac(80M) 5.2G_Head_Le Cheek_CH 42
Communication System: WLAN 5G; Frequency: 5210 MHz, Duty Cycle: 1:1
Medium parameters used: f = 5210 MHz; σ = 4.737 S/m; εr = 34.976; ρ = 1000 kg/m3
Phantom section: Left Section
Ambient temperature: 23.5° C ; Liquid temperature: 22.4° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(4.76, 4.76, 4.76); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (91x161x1): Interpolated grid: dx=10 mm, dy=10
mm
Maximum value of SAR (interpolated) = 0.373 W/kg
Configuration/Head/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm,
dy=4mm, dz=2mm
Reference Value = 0.5510 V/m; Power Drift = 0.06 dB
Peak SAR (extrapolated) = 0.570 W/kg
SAR(1 g) = 0.135 W/kg; SAR(10 g) = 0.034 W/kg
Maximum value of SAR (measured) = 0.307 W/kg
0 dB = 0.307 W/kg = -5.13 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 58 of 130
Date: 2016/11/25
WLAN 802.11ac(80M) 5.2G_Body-worn_Back side_CH 42_10mm
Communication System: WLAN(5G); Frequency: 5210 MHz, Duty Cycle: 1:1
Medium parameters used: f = 5210 MHz; σ = 5.343 S/m; εr = 48.372; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.6° C ; Liquid temperature: 22.1° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(4.07, 4.07, 4.07); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (101x161x1): Interpolated grid: dx=10 mm, dy=10
mm
Maximum value of SAR (interpolated) = 0.139 W/kg
Configuration/Head/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm,
dy=4mm, dz=2mm
Reference Value = 0.6880 V/m; Power Drift = 0.17 dB
Peak SAR (extrapolated) = 0.263 W/kg
SAR(1 g) = 0.072 W/kg; SAR(10 g) = 0.024 W/kg
Maximum value of SAR (measured) = 0.147 W/kg
0 dB = 0.147 W/kg = -8.33 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 59 of 130
Date: 2016/11/23
WLAN 802.11ac(80M) 5.3G_Head_Le Cheek_CH 58
Communication System: WLAN 5G; Frequency: 5290 MHz, Duty Cycle: 1:1
Medium parameters used: f = 5290 MHz; σ = 4.858 S/m; εr = 34.465; ρ = 1000 kg/m3
Phantom section: Left Section
Ambient temperature: 23.5° C ; Liquid temperature: 22.4° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(4.46, 4.46, 4.46); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (91x161x1): Interpolated grid: dx=10 mm, dy=10
mm
Maximum value of SAR (interpolated) = 0.399 W/kg
Configuration/Head/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm,
dy=4mm, dz=2mm
Reference Value = 1.238 V/m; Power Drift = 0.01 dB
Peak SAR (extrapolated) = 0.443 W/kg
SAR(1 g) = 0.098 W/kg; SAR(10 g) = 0.025 W/kg
Maximum value of SAR (measured) = 0.240 W/kg
0 dB = 0.240 W/kg = -6.19 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 60 of 130
Date: 2016/11/25
WLAN 802.11ac(80M) 5.3G_Body-worn_Back side_CH 58_10mm
Communication System: WLAN(5G); Frequency: 5290 MHz, Duty Cycle: 1:1
Medium parameters used: f = 5290 MHz; σ = 5.427 S/m; εr = 48.258; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.6° C ; Liquid temperature: 22.1° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(3.81, 3.81, 3.81); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (101x161x1): Interpolated grid: dx=10 mm, dy=10
mm
Maximum value of SAR (interpolated) = 0.116 W/kg
Configuration/Head/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm,
dy=4mm, dz=2mm
Reference Value = 1.014 V/m; Power Drift = 0.03 dB
Peak SAR (extrapolated) = 0.231 W/kg
SAR(1 g) = 0.059 W/kg; SAR(10 g) = 0.019 W/kg
Maximum value of SAR (measured) = 0.122 W/kg
0 dB = 0.122 W/kg = -9.14 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 61 of 130
Date: 2016/11/23
WLAN 802.11ac(80M) 5.6G_Head_Le Tilt_CH 138
Communication System: WLAN 5G; Frequency: 5690 MHz, Duty Cycle: 1:1
Medium parameters used: f = 5690 MHz; σ = 5.303 S/m; εr = 34.303; ρ = 1000 kg/m3
Phantom section: Left Section
Ambient temperature: 23.5° C ; Liquid temperature: 22.4° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(4.08, 4.08, 4.08); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (91x161x1): Interpolated grid: dx=10 mm, dy=10
mm
Maximum value of SAR (interpolated) = 0.407 W/kg
Configuration/Head/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm,
dy=4mm, dz=2mm
Reference Value = 2.051 V/m; Power Drift = 0.09 dB
Peak SAR (extrapolated) = 1.10 W/kg
SAR(1 g) = 0.095 W/kg; SAR(10 g) = 0.022 W/kg
Maximum value of SAR (measured) = 0.166 W/kg
0 dB = 0.166 W/kg = -7.79 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 62 of 130
Date: 2016/11/25
WLAN 802.11ac(80M) 5.6G_Body-worn_Back side_CH 138_10mm
Communication System: WLAN(5G); Frequency: 5690 MHz, Duty Cycle: 1:1
Medium parameters used: f = 5690 MHz; σ = 5.974 S/m; εr = 48.649; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.6° C ; Liquid temperature: 22.1° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(3.47, 3.47, 3.47); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Head/Area Scan (101x161x1): Interpolated grid: dx=10 mm, dy=10
mm
Maximum value of SAR (interpolated) = 0.117 W/kg
Configuration/Head/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm,
dy=4mm, dz=2mm
Reference Value = 0.8100 V/m; Power Drift = -0.12 dB
Peak SAR (extrapolated) = 0.191 W/kg
SAR(1 g) = 0.027 W/kg; SAR(10 g) = 0.00826 W/kg
Maximum value of SAR (measured) = 0.0597 W/kg
0 dB = 0.0597 W/kg = -12.24 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 63 of 130
6. SAR System Performance Verification
Date: 2016/11/22
Dipole 835 MHz_SN:4d063_Head
Communication System: CW; Frequency: 835 MHz, Duty Cycle: 1:1
Medium parameters used: f = 835 MHz; σ = 0.882 S/m; εr = 41.181; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.4° C ; Liquid temperature: 21.8° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(8.84, 8.84, 8.84); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Pin=250mW/Area Scan (41x121x1): Interpolated grid: dx=15 mm,
dy=15 mm
Maximum value of SAR (interpolated) = 2.98 W/kg
Configuration/Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid:
dx=5mm, dy=5mm, dz=5mm
Reference Value = 58.32 V/m; Power Drift = -0.01 dB
Peak SAR (extrapolated) = 3.56 W/kg
SAR(1 g) = 2.33 W/kg; SAR(10 g) = 1.49 W/kg
Maximum value of SAR (measured) = 2.99 W/kg
0 dB = 2.99 W/kg = 4.76 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 64 of 130
Date: 2016/11/24
Dipole 835 MHz_SN:4d063_Body
Communication System: CW; Frequency: 835 MHz, Duty Cycle: 1:1
Medium parameters used: f = 835 MHz; σ = 0.996 S/m; εr = 53.336; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.5° C ; Liquid temperature: 22.0° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(9.08, 9.08, 9.08); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Pin=250mW/Area Scan (51x131x1): Interpolated grid: dx=15 mm,
dy=15 mm
Maximum value of SAR (interpolated) = 3.39 W/kg
Configuration/Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid:
dx=5mm, dy=5mm, dz=5mm
Reference Value = 58.93 V/m; Power Drift = 0.02 dB
Peak SAR (extrapolated) = 4.05 W/kg
SAR(1 g) = 2.56 W/kg; SAR(10 g) = 1.61 W/kg
Maximum value of SAR (measured) = 3.42 W/kg
0 dB = 3.42 W/kg = 5.34 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 65 of 130
Date: 2016/11/22
Dipole 1900 MHz_SN:5d027_Head
Communication System: CW; Frequency: 1900 MHz, Duty Cycle: 1:1
Medium parameters used: f = 1900 MHz; σ = 1.429 S/m; εr = 40.087; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.1° C ; Liquid temperature: 22.0° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(7.66, 7.66, 7.66); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Pin=250mW/Area Scan (51x61x1): Interpolated grid: dx=15 mm,
dy=15 mm
Maximum value of SAR (interpolated) = 13.9 W/kg
Configuration/Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid:
dx=5mm, dy=5mm, dz=5mm
Reference Value = 102.2 V/m; Power Drift = -0.03 dB
Peak SAR (extrapolated) = 17.7 W/kg
SAR(1 g) = 9.56 W/kg; SAR(10 g) = 4.98 W/kg
Maximum value of SAR (measured) = 13.8 W/kg
0 dB = 13.8 W/kg = 11.40 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 66 of 130
Date: 2016/11/24
Dipole 1900 MHz_SN:5d027_Body
Communication System: CW; Frequency: 1900 MHz, Duty Cycle: 1:1
Medium parameters used: f = 1900 MHz; σ = 1.563 S/m; εr = 51.961; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.4° C ; Liquid temperature: 22.2° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(7.54, 7.54, 7.54); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Pin=250mW/Area Scan (51x61x1): Interpolated grid: dx=15 mm,
dy=15 mm
Maximum value of SAR (interpolated) = 15.1 W/kg
Configuration/Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid:
dx=5mm, dy=5mm, dz=5mm
Reference Value = 102.6 V/m; Power Drift = 0.06 dB
Peak SAR (extrapolated) = 18.8 W/kg
SAR(1 g) = 10.1 W/kg; SAR(10 g) = 5.21 W/kg
Maximum value of SAR (measured) = 14.6 W/kg
0 dB = 14.6 W/kg = 11.64 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 67 of 130
Date: 2016/11/22
Dipole 2450 MHz_SN:727_Head
Communication System: CW; Frequency: 2450 MHz, Duty Cycle: 1:1
Medium parameters used: f = 2450 MHz; σ = 1.826 S/m; εr = 38.213; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.4° C ; Liquid temperature: 22.1° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(6.92, 6.92, 6.92); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Pin=250mW/Area Scan (51x61x1): Interpolated grid: dx=15 mm,
dy=15 mm
Maximum value of SAR (interpolated) = 20.4 W/kg
Configuration/Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid:
dx=5mm, dy=5mm, dz=5mm
Reference Value = 106.5 V/m; Power Drift = 0.03 dB
Peak SAR (extrapolated) = 27.1 W/kg
SAR(1 g) = 12.9 W/kg; SAR(10 g) = 5.93 W/kg
Maximum value of SAR (measured) = 19.7 W/kg
0 dB = 19.7 W/kg = 12.94 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 68 of 130
Date: 2016/11/25
Dipole 2450 MHz_SN:727_Body
Communication System: CW; Frequency: 2450 MHz, Duty Cycle: 1:1
Medium parameters used: f = 2450 MHz; σ = 1.974 S/m; εr = 52.573; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.7° C ; Liquid temperature: 22.0° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(7.05, 7.05, 7.05); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Pin=250mW/Area Scan (51x51x1): Interpolated grid: dx=12 mm,
dy=12 mm
Maximum value of SAR (interpolated) = 20.1 W/kg
Configuration/Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid:
dx=5mm, dy=5mm, dz=5mm
Reference Value = 98.41 V/m; Power Drift = -0.01 dB
Peak SAR (extrapolated) = 24.8 W/kg
SAR(1 g) = 12.1 W/kg; SAR(10 g) = 5.62 W/kg
Maximum value of SAR (measured) = 18.5 W/kg
0 dB = 18.5 W/kg = 12.67 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 69 of 130
Date: 2016/11/23
Dipole 5200 MHz_SN:1023_Head
Communication System: CW; Frequency: 5200 MHz, Duty Cycle: 1:1
Medium parameters used: f = 5200 MHz; σ = 4.726 S/m; εr = 35.052; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.5° C ; Liquid temperature: 22.4° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(4.76, 4.76, 4.76); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Pin=100mW/Area Scan (71x91x1): Interpolated grid: dx=10 mm,
dy=10 mm
Maximum value of SAR (interpolated) = 17.2 W/kg
Configuration/Pin=100mW/Zoom Scan (7x7x12)/Cube 0: Measurement grid:
dx=4mm, dy=4mm, dz=2mm
Reference Value = 59.33 V/m; Power Drift = -0.06 dB
Peak SAR (extrapolated) = 28.6 W/kg
SAR(1 g) = 7.71 W/kg; SAR(10 g) = 2.22 W/kg
Maximum value of SAR (measured) = 16.1 W/kg
0 dB = 16.1 W/kg = 12.06 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 70 of 130
Date: 2016/11/25
Dipole 5200 MHz_SN:1023_Body
Communication System: CW; Frequency: 5200 MHz, Duty Cycle: 1:1
Medium parameters used: f = 5200 MHz; σ = 5.333 S/m; εr = 48.387; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.6° C ; Liquid temperature: 22.1° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(4.07, 4.07, 4.07); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Pin=100mW/Area Scan (71x91x1): Interpolated grid: dx=10 mm,
dy=10 mm
Maximum value of SAR (interpolated) = 15.0 W/kg
Configuration/Pin=100mW/Zoom Scan (7x7x12)/Cube 0: Measurement grid:
dx=4mm, dy=4mm, dz=2mm
Reference Value = 56.71 V/m; Power Drift = -0.13 dB
Peak SAR (extrapolated) = 25.6 W/kg
SAR(1 g) = 7.53 W/kg; SAR(10 g) = 2.06 W/kg
Maximum value of SAR (measured) = 14.8 W/kg
0 dB = 14.8 W/kg = 11.70 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 71 of 130
Date: 2016/11/23
Dipole 5300 MHz_SN:1023_Head
Communication System: CW; Frequency: 5300 MHz, Duty Cycle: 1:1
Medium parameters used: f = 5300 MHz; σ = 4.869 S/m; εr = 34.453; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.5° C ; Liquid temperature: 22.4° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(4.46, 4.46, 4.46); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Pin=100mW/Area Scan (71x91x1): Interpolated grid: dx=10 mm,
dy=10 mm
Maximum value of SAR (interpolated) = 17.9 W/kg
Configuration/Pin=100mW/Zoom Scan (7x7x12)/Cube 0: Measurement grid:
dx=4mm, dy=4mm, dz=2mm
Reference Value = 59.55 V/m; Power Drift = -0.18 dB
Peak SAR (extrapolated) = 29.7 W/kg
SAR(1 g) = 8.28 W/kg; SAR(10 g) = 2.34 W/kg
Maximum value of SAR (measured) = 16.8 W/kg
0 dB = 16.8 W/kg = 12.24 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 72 of 130
Date: 2016/11/25
Dipole 5300 MHz_SN:1023_Body
Communication System: CW; Frequency: 5300 MHz, Duty Cycle: 1:1
Medium parameters used: f = 5300 MHz; σ = 5.411 S/m; εr = 48.245; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.6° C ; Liquid temperature: 22.1° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(3.81, 3.81, 3.81); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Pin=100mW/Area Scan (71x91x1): Interpolated grid: dx=10 mm,
dy=10 mm
Maximum value of SAR (interpolated) = 15.7 W/kg
Configuration/Pin=100mW/Zoom Scan (7x7x12)/Cube 0: Measurement grid:
dx=4mm, dy=4mm, dz=2mm
Reference Value = 56.45 V/m; Power Drift = -0.13 dB
Peak SAR (extrapolated) = 27.8 W/kg
SAR(1 g) = 7.78 W/kg; SAR(10 g) = 2.17 W/kg
Maximum value of SAR (measured) = 15.3 W/kg
0 dB = 15.3 W/kg = 11.86 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 73 of 130
Date: 2016/11/23
Dipole 5600 MHz_SN:1023_Head
Communication System: CW; Frequency: 5600 MHz, Duty Cycle: 1:1
Medium parameters used: f = 5600 MHz; σ = 5.213 S/m; εr = 34.406; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.5° C ; Liquid temperature: 22.4° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(4.08, 4.08, 4.08); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Pin=100mW/Area Scan (71x91x1): Interpolated grid: dx=10 mm,
dy=10 mm
Maximum value of SAR (interpolated) = 18.3 W/kg
Configuration/Pin=100mW/Zoom Scan (7x7x12)/Cube 0: Measurement grid:
dx=4mm, dy=4mm, dz=2mm
Reference Value = 59.28 V/m; Power Drift = -0.15 dB
Peak SAR (extrapolated) = 31.8 W/kg
SAR(1 g) = 8.4 W/kg; SAR(10 g) = 2.46 W/kg
Maximum value of SAR (measured) = 17.1 W/kg
0 dB = 17.1 W/kg = 12.34 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 74 of 130
Date: 2016/11/25
Dipole 5600 MHz_SN:1023_Body
Communication System: CW; Frequency: 5600 MHz, Duty Cycle: 1:1
Medium parameters used: f = 5600 MHz; σ = 5.868 S/m; εr = 48.772; ρ = 1000 kg/m3
Phantom section: Flat Section
Ambient temperature: 23.6° C ; Liquid temperature: 22.1° C
DASY5 Configuration:
 Probe: EX3DV4 - SN3831; ConvF(3.47, 3.47, 3.47); Calibrated: 2016/1/27;
 Sensor-Surface: 2mm (Mechanical Surface Detection)
 Electronics: DAE4 Sn547; Calibrated: 2016/3/21
 Phantom: Head
 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373)
Configuration/Pin=100mW/Area Scan (71x91x1): Interpolated grid: dx=10 mm,
dy=10 mm
Maximum value of SAR (interpolated) = 17.1 W/kg
Configuration/Pin=100mW/Zoom Scan (7x7x12)/Cube 0: Measurement grid:
dx=4mm, dy=4mm, dz=2mm
Reference Value = 55.04 V/m; Power Drift = -0.15 dB
Peak SAR (extrapolated) = 34.0 W/kg
SAR(1 g) = 8.13 W/kg; SAR(10 g) = 2.32 W/kg
Maximum value of SAR (measured) = 17.0 W/kg
0 dB = 17.0 W/kg = 12.32 dBW/kg
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 75 of 130
7. DAE & Probe Calibration Certificate
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 76 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 77 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 78 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 79 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 80 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 81 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 82 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 83 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 84 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 85 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 86 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 87 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 88 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 89 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 90 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 91 of 130
8. Uncertainty Budget
Measurement Uncertainty evaluation template for DUT SAR test (3-6G)
Source of Uncertainty
Tolerance/ Probabilit
Uncertainty
Div
Div Value ci (1g)
h=c * f / e
i=c * g / e
ci (10g)
Standard
uncertainty
Standard
uncertainty
vi, or Veff
Measurement system
6.55%
6.55%
∞
√3
1.732
2.02%
2.02%
∞
√3
1.732
5.54%
5.54%
∞
2.40%
√3
1.732
1.40%
1.40%
∞
Boundary Effect
1.00%
√3
1.732
0.58%
0.58%
∞
Linearity
4.70%
√3
1.732
2.71%
2.71%
∞
Detection Limits
1.00%
√3
1.732
0.58%
0.58%
∞
Readout Electronics
0.30%
0.30%
0.30%
∞
Response time
0.80%
√3
1.732
0.46%
0.46%
∞
Integration Time
2.60%
√3
1.732
1.50%
1.50%
∞
1.75%
√3
1.732
1.01%
1.01%
∞
3.00%
√3
1.732
1.73%
1.73%
∞
3.00%
√3
1.732
1.73%
1.73%
∞
0.40%
√3
1.732
0.23%
0.23%
∞
2.90%
√3
1.732
1.67%
1.67%
∞
Post-processing
1.00%
√3
1.732
0.58%
0.58%
∞
Max SAR Eval
1.00%
√3
1.732
0.58%
0.58%
∞
Test sample positioning
2.90%
2.90%
2.90%
M-1
Device Holder
Uncertainty
3.60%
3.60%
3.60%
M-1
Drift of output power
5.00%
√3
1.732
2.89%
2.89%
∞
Phantom Uncertainty
4.00%
√3
1.732
2.31%
2.31%
∞
Liquid permittivity
(mea.)
3.95%
0.64
0.43
2.53%
1.70%
Liquid Conductivity
(mea.)
2.92%
0.6
0.49
1.75%
1.43%
12.11%
11.92%
24.23%
23.83%
Probe calibration
6.55%
Isotropy , Axial
3.50%
Isotropy,
Hemispherical
9.60%
Modulation Response
Measurement drift
(class A evaluation)
RF ambient condition noise
RF ambient conditions reflections
Probe positioner
Mechanical restrictions
Probe Positioning with
respect to phantom
Test Sample related
Phantom and Setup
Combined standard
uncertainty
Expant uncertainty
(95% confidence
RSS
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 92 of 130
Measurement Uncertainty evaluation template for DUT SAR test (0.3-3G)
Source of Uncertainty
Tolerance/ Probabilit
Uncertainty
Div
Div Value ci (1g)
h=c * f / e
i=c * g / e
ci (10g)
Standard
uncertainty
Standard
uncertainty
vi, or Veff
Measurement system
6.00%
6.00%
∞
√3
1.732
2.02%
2.02%
∞
√3
1.732
5.54%
5.54%
∞
2.40%
√3
1.732
1.40%
1.40%
∞
Boundary Effect
1.00%
√3
1.732
0.58%
0.58%
∞
Linearity
4.70%
√3
1.732
2.71%
2.71%
∞
Detection Limits
1.00%
√3
1.732
0.58%
0.58%
∞
Readout Electronics
0.30%
0.30%
0.30%
∞
Response time
0.80%
√3
1.732
0.46%
0.46%
∞
Integration Time
2.60%
√3
1.732
1.50%
1.50%
∞
1.75%
√3
1.732
1.01%
1.01%
∞
3.00%
√3
1.732
1.73%
1.73%
∞
3.00%
√3
1.732
1.73%
1.73%
∞
0.40%
√3
1.732
0.23%
0.23%
∞
2.90%
√3
1.732
1.67%
1.67%
∞
Post-processing
1.00%
√3
1.732
0.58%
0.58%
∞
Max SAR Eval
1.00%
√3
1.732
0.58%
0.58%
∞
Test sample positioning
2.90%
2.90%
2.90%
M-1
Device Holder
Uncertainty
3.60%
3.60%
3.60%
M-1
Drift of output power
5.00%
√3
1.732
2.89%
2.89%
∞
Phantom Uncertainty
4.00%
√3
1.732
2.31%
2.31%
∞
Liquid permittivity
(mea.)
3.56%
0.64
0.43
2.28%
1.53%
Liquid Conductivity
(mea.)
3.49%
0.6
0.49
2.09%
1.71%
11.83%
11.64%
23.66%
23.27%
Probe calibration
6.00%
Isotropy , Axial
3.50%
Isotropy,
Hemispherical
9.60%
Modulation Response
Measurement drift
(class A evaluation)
RF ambient condition noise
RF ambient conditions reflections
Probe positioner
Mechanical restrictions
Probe Positioning with
respect to phantom
Test Sample related
Phantom and Setup
Combined standard
uncertainty
Expant uncertainty
(95% confidence
RSS
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 93 of 130
9. Phantom Description
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 94 of 130
10. System Validation from Original Equipment Supplier
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 95 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 96 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 97 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 98 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 99 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 100 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 101 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 102 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 103 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 104 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 105 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 106 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 107 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 108 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 109 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 110 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 111 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 112 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 113 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 114 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 115 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 116 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 117 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 118 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 119 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 120 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 121 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 122 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 123 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 124 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 125 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 126 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 127 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 128 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 129 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Report No. : E5/2016/B0002
Page : 130 of 130
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.
除非另有說明,此報告結果僅對測試之樣品負責,同時此樣品僅保留90天。本報告未經本公司書面許可,不可部份複製。
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format
documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined
therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot
be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be
prosecuted to the fullest extent of the law.
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司
No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/新北市五股區新北產業園區五工路 134 號
t (886-2) 2299-3279
f (886-2) 2298-0488
www.tw.sgs.com
Member of SGS Group
Download: F04J Mobile Phone RF Exposure Info Test Report_SAR Fujitsu Limited
Mirror Download [FCC.gov]F04J Mobile Phone RF Exposure Info Test Report_SAR Fujitsu Limited
Document ID3249539
Application IDYcjJeb0foeZqb8IWRKxYpw==
Document DescriptionTest Report_SAR
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeRF Exposure Info
Display FormatAdobe Acrobat PDF - pdf
Filesize166.86kB (2085773 bits)
Date Submitted2017-01-06 00:00:00
Date Available2017-01-10 00:00:00
Creation Date2017-12-20 09:56:41
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-12-20 09:56:41
Document TitleTest Report_SAR
Document CreatorPScript5.dll Version 5.2.2
Document Author: Jasmine_Lu

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:75bd6c62-a2b6-11f2-0000-02c7314339d4
Producer                        : GPL Ghostscript 9.18
Modify Date                     : 2017:07:17 02:44:53Z
Create Date                     : 2017:07:17 02:44:53Z
Creator Tool                    : UnknownApplication
Document ID                     : uuid:75bd6c62-a2b6-11f2-0000-02c7314339d4
Format                          : application/pdf
Title                           : Untitled
EXIF Metadata provided by EXIF.tools

Facebook Twitter Google+ RSS © FCCID.io 2018