APINH303 802.11a/b/g/n/ac Wireless Access Point Test Report ©2016 MiCOM Labs Inc. Aruba Networks, Inc.

Aruba Networks, Inc. 802.11a/b/g/n/ac Wireless Access Point

FCC ID Filing: Q9DAPINH303
Purchase on Amazon: 802.11a/b/g/n/ac Wireless Access Point

Trouble Viewing? See the or view the HTML Version or PDF in frame
Page 1 of APINH303 802.11a/b/g/n/ac Wireless Access Point Test Report ©2016 MiCOM Labs Inc. Aruba Networks, Inc.

Company: Hewlett Packard Enterprise
Test of: APINH303
To: FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
Report No.: HWPD85-U2 Rev A Bluetooth BLE
TEST REPORT
FROM
Test of: Hewlett Packard Enterprise APINH303
to
To: FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
Test Report Serial No.: HWPD85-U2 Rev A Bluetooth BLE
This report supersedes: NONE
Applicant:
Product Function:
Issue Date:
Hewlett Packard Enterprise
3000 Hanover St.
Palo Alto, California 94034
USA
802.11 a/b/g/n/ac Wireless Access
Point & BLE
1st December 2016
This Test Report is Issued Under the Authority of:
MiCOM Labs, Inc.
575 Boulder Court
Pleasanton California 94566
USA
Phone: +1 (925) 462-0304
Fax: +1 (925) 462-0306
www.micomlabs.com
MiCOM Labs is an ISO 17025 Accredited Testing Laboratory
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
3 of 62
Table of Contents
1. ACCREDITATION, LISTINGS & RECOGNITION................................................................................. 4
1.1. Testing Accreditation ..................................................................................................................... 4
1.2. Recognition .................................................................................................................................... 5
1.3. Product Certification ...................................................................................................................... 6
2. DOCUMENT HISTORY ......................................................................................................................... 7
3. TEST RESULT CERTIFICATE .............................................................................................................. 8
4. REFERENCES AND MEASUREMENT UNCERTAINTY ..................................................................... 9
4.1. Normative References ................................................................................................................... 9
4.2. Test and Uncertainty Procedure .................................................................................................. 10
5. PRODUCT DETAILS AND TEST CONFIGURATIONS ...................................................................... 11
5.1. Technical Details ......................................................................................................................... 11
5.2. Scope Of Test Program ............................................................................................................... 12
5.3. Equipment Model(s) and Serial Number(s) ................................................................................. 13
5.4. Antenna Details ........................................................................................................................... 13
5.5. Cabling and I/O Ports .................................................................................................................. 13
5.6. Test Configurations...................................................................................................................... 14
5.7. Equipment Modifications ............................................................................................................. 14
5.8. Deviations from the Test Standard .............................................................................................. 14
6. TEST SUMMARY ................................................................................................................................ 15
7. TEST EQUIPMENT CONFIGURATION(S) ......................................................................................... 16
7.1. Conducted ................................................................................................................................... 16
7.2. Radiated Emissions - 3m Chamber ............................................................................................. 18
8. MEASUREMENT AND PRESENTATION OF TEST DATA ............................................................... 21
9. TEST RESULTS .................................................................................................................................. 22
9.1. 6 dB & 99% Bandwidth ................................................................................................................ 22
9.2. Conducted Output Power ............................................................................................................ 24
9.3 Conducted Spurious Emissions ................................................................................................. 27
9.3.1 Conducted Emissions ......................................................................................................... 27
9.3.2 Conducted Band-Edge Emissions ...................................................................................... 29
Low Band-Edge Emissions ...................................................................................................... 29
High Band-Edge Emissions ..................................................................................................... 30
9.4 Power Spectral Density ............................................................................................................. 31
9.5 Radiated Emissions ................................................................................................................... 33
9.5.1 Restricted Band Emissions ................................................................................................. 36
9.5.2 Restricted Edge & Band-Edge Emissions .......................................................................... 39
A. APPENDIX - GRAPHICAL IMAGES .................................................................................................. 42
A.1. 6 dB & 99% Bandwidth ............................................................................................................... 43
A.2. Conducted Emissions.................................................................................................................. 46
A.2.1 Conducted Spurious Emissions .......................................................................................... 46
A.2.2 Conducted Band Edge Emissions ...................................................................................... 49
A.3. Power Spectral Density ............................................................................................................... 51
A.4. Radiated Emissions..................................................................................................................... 57
A.4.1. TX Spurious & Restricted Band Emissions .......................................................................... 57
A.4.2. Restricted Edge & Band-Edge Emissions ............................................................................ 60
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
4 of 62
1. ACCREDITATION, LISTINGS & RECOGNITION
1.1. Testing Accreditation
MiCOM Labs, Inc. is an accredited Electrical testing laboratory per the international standard ISO/IEC
17025:2005. The company is accredited by the American Association for Laboratory Accreditation
(A2LA) www.a2la.org test laboratory number 2381.01. MiCOM Labs test schedule is available at the
following URL; http://www.a2la.org/scopepdf/2381-01.pdf
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
5 of 62
1.2. Recognition
MiCOM Labs, Inc. has widely recognized wireless testing capabilities. Our international recognition
includes Conformity Assessment Body designation by APEC MRA countries. MiCOM Labs test reports
are accepted globally.
Country
USA
Canada
Recognition Body
Status
Phase
Federal Communications
Commission (FCC)
TCB
Industry Canada (IC)
FCB
APEC MRA 2
CAB
APEC MRA 2
RCB 210
--
--
A-0012
NB
EU MRA
NB 2280
CAB
APEC MRA 1
CAB
APEC MRA 1
CAB
APEC MRA 1
CAB
APEC MRA 1
MIC (Ministry of Internal
Affairs and Communication)
VCCI
Japan
Europe
European Commission
Australia
Hong Kong
Korea
Singapore
Taiwan
Vietnam
Australian Communications
and Media Authority (ACMA)
Office of the
Telecommunication Authority
(OFTA)
Ministry of Information and
Communication Radio
Research Laboratory (RRL)
Infocomm Development
Authority (IDA)
National Communications
Commission (NCC)
Bureau of Standards,
Metrology and Inspection
(BSMI)
Ministry of Communication
(MIC)
Identification No.
US0159
Listing #: 102167
US0159
Listing #: 4143A-2
4143A-3
US0159
APEC MRA 1
CAB
CAB
APEC MRA 1
EU MRA – European Union Mutual Recognition Agreement.
NB – Notified Body
APEC MRA – Asia Pacific Economic Community Mutual Recognition Agreement. Recognition
agreement under which test lab is accredited to regulatory standards of the APEC member countries.
Phase I - recognition for product testing
Phase II – recognition for both product testing and certification
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
6 of 62
1.3. Product Certification
MiCOM Labs, Inc. is an accredited Product Certification Body per the international standard ISO/IEC
17065:2012. The company is accredited by the American Association for Laboratory Accreditation
(A2LA) www.a2la.org test laboratory number 2381.02. MiCOM Labs test schedule is available at the
following URL; http://www.a2la.org/scopepdf/2381-02.pdf
United States of America – Telecommunication Certification Body (TCB)
Industry Canada – Certification Body, CAB Identifier – US0159
Europe – Notified Body (NB), NB Identifier - 2280
Japan – Recognized Certification Body (RCB), RCB Identifier - 210
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
7 of 62
2. DOCUMENT HISTORY
Report History
Revision
Date
Comments
Draft
Rev A
st
1 December 2016
Initial release.
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
8 of 62
Title:
To:
Serial #:
Issue Date:
Page:
3. TEST RESULT CERTIFICATE
Manufacturer: Hewlett Packard Enterprise
3000 Hanover St.
Palo Alto
California 94034 USA
Tested By: MiCOM Labs, Inc.
575 Boulder Court
Pleasanton
California 94566 USA
Model: APINH303
Telephone: +1 925 462 0304
Fax: +1 925 462 0306
Type Of Equipment: 802.11a/b/g/n/ac Wireless Access
Point & BLE
S/N’s: CNC7K2R00X
Test Date(s): 31st October – 4th November 2016
Website: www.micomlabs.com
STANDARD(S)
TEST RESULTS
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
EQUIPMENT COMPLIES
MiCOM Labs, Inc. tested the equipment mentioned in accordance with the requirements set forth in the
above standards. Test results indicate that the equipment tested is capable of demonstrating
compliance with the requirements as documented within this report.
Notes:
1. This document reports conditions under which testing was conducted and the results of testing
performed.
2. Details of test methods used have been recorded and kept on
file by the laboratory.
3. Test results apply only to the item(s) tested.
Approved & Released for MiCOM Labs, Inc. by:
Graeme Grieve
Quality Manager MiCOM Labs, Inc.
Gordon Hurst
President & CEO MiCOM Labs, Inc.
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
9 of 62
4. REFERENCES AND MEASUREMENT UNCERTAINTY
4.1. Normative References
REF.
PUBLICATION
KDB 662911 D01
& D02
II
KDB 558074 D01
v03r05
III
A2LA
IV
ANSI C63.10
ANSI C63.4
VI
CISPR 22
VII
ETSI TR 100 028
VIII
FCC 47 CFR Part
15.247
IX
ICES-003
M 3003
XI
RSS-247 Issue 1
XII
RSS-Gen Issue 4
XIII
XIV
KDB 644545 D03
v01
FCC 47 CFR Part
2.1033
YEAR
TITLE
Guidance for measurement of output emission of devices
that employ single transmitter with multiple outputs or
Oct 31 2013
systems with multiple transmitters operating
simultaneously in the same frequency band
Guidance for performing compliance measurements on
8th April 2016
Digital Transmission Systems (DTS) operating under
section 15.247.
R105 - Requirement's When Making Reference to A2LA
June 2015
Accreditation Status
American National Standard for Testing Unlicensed
2013
Wireless Devices
American National Standards for Methods of
Measurement of Radio-Noise Emissions from Low2014
Voltage Electrical and Electronic Equipment in the Range
of 9 kHz to 40 GHz
Information technology equipment - Radio disturbance
2008
characteristics - Limits and methods of measurement
Parts 1 and 2 Electromagnetic compatibility and Radio
2001-12
Spectrum Matters (ERM); Uncertainties in the
measurement of mobile radio equipment characteristics
Radio Frequency Devices; Subpart C – Intentional
2014
Radiators
Spectrum Management and Telecommunications;
Interference-Causing Equipment Standard. Information
Issue 6 Jan 2016
Technology Equipment (Including Digital Apparatus) –
Limits and methods of measurement.
Expression of Uncertainty and Confidence in
Edition 3 Nov.2012
Measurements
Digital Transmission Systems (DTSs), Frequency
May 2015
Hopping System (FHSs) and Licence-Exempt Local Area
Network (LE-LEN) Devices
General Requirements and Information for the
November 2014
Certification of Radiocommunication Equipment
August 14th 2014
2014
Guidance for IEEE 802.11ac New Rules
FCC requirements and rules regarding photographs and
test setup diagrams.
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
10 of 62
4.2. Test and Uncertainty Procedure
Conducted and radiated emission measurements were conducted in accordance with American
National Standards Institute ANSI C63.4, listed in the Normative References section of this report.
Measurement uncertainty figures are calculated in accordance with ETSI TR 100 028 Parts 1 and 2.
Measurement uncertainties stated are based on a standard uncertainty multiplied by a coverage
factor k = 2, providing a level of confidence of approximately 95 % in accordance with UKAS
document M 3003 listed in the Normative References section of this report.
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
11 of 62
5. PRODUCT DETAILS AND TEST CONFIGURATIONS
5.1. Technical Details
Details Description
Purpose: Test of the Hewlett Packard Enterprise APINH303 to FCC CFR 47
Part 15 Subpart C 15.247 (DTS) & IC RSS-247
Applicant: Hewlett Packard Enterprise
3000 Hanover St., Palo Alto California 94034 USA
Manufacturer: As Applicant
Laboratory performing the tests: MiCOM Labs, Inc.
575 Boulder Court, Pleasanton California 94566 USA
Test report reference number: HWPD85-U2 Rev A
Date EUT received: 31st October 2016
Standard(s) applied: FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
Dates of test (from - to): 31st October – 4th November 2016
No of Units Tested: 2
Type of Equipment: 802.11 a/b/g/n/ac & BLE Wireless Access Point
Product Family Name: Access Point
Model(s): APINH303
Location for use: Indoor
Declared Frequency Range(s): 2400 - 2483.5 MHz;
Primary function of equipment: Transmission of voice and/ or data
Secondary function of equipment: None Provided
Type of Modulation: GFSK
EUT Modes of Operation: GFSK
Transmit/Receive Operation: Transceiver - Full Duplex
Rated Input Voltage and Current: AC/ DC adaptor (adaptor NOT sold with unit) 48Vdc
Operating Temperature Range: Declared Range 0°C to 40°C
ITU Emission Designator: BLE: 1M1G1D
Equipment Dimensions: 150mm x 86mm X 38mm
Weight: 0.26kg (0.6 lbs)
Hardware Rev: P2-2
Software Image: ipq40xxqdart.ari.abeaudin-rd-sw-inst2-wip (Time Stamp 11/03/16
14:08)
Firmware Smart RF Studio 7 2.2.1 (firmware Rev. 0025)
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
12 of 62
5.2. Scope Of Test Program
Hewlett Packard Enterprise APINH303
The scope of the test program was to test the Hewlett Packard Enterprise APINH303 Bluetooth BLE
configurations in the frequency ranges 2400 - 2483.5 MHz; for compliance against the following
specifications:
FCC CFR 47 Part 15 Subpart C 15.247 (DTS)
Radio Frequency Devices; Subpart C – Intentional Radiators
Industry Canada RSS-247 Issue 1
Digital Transmission Systems (DTSs), Frequency Hopping System (FHSs) and License-Exempt Local
Area Network (LE-LEN) Devices.
Hewlett Packard Enterprise APINH303
EUT_MAIN_PICTURE
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
13 of 62
Title:
To:
Serial #:
Issue Date:
Page:
5.3. Equipment Model(s) and Serial Number(s)
Type
EUT
Support
Description
802.11 a/b/g/n/ac/ac
Wireless Access Point
Laptop PC
Manufacturer
Hewlett Packard
Enterprise
DELL
Model
Serial no.
Delivery Date
st
APINH303 CNC7K2R00X 31 October 2016
E7450
None
N/A
5.4. Antenna Details
Type
Manufacturer
Model
Metal
sheet
BF Gain - Beamforming Gain
Dir BW - Directional BeamWidth
X-Pol - Cross Polarization
integral
Aruba
Family
Gain
(dBi)
BF Gain
Dir BW
X-Pol
Frequency
Band (MHz)
PCB
3.2
3.0
360
2400 - 2483.5
5.5. Cabling and I/O Ports
Port Type
Ethernet
Max Cable
Length
100
# Of Ports
Screened
Conn Type
Data Type
RJ45
Packet Data
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
14 of 62
5.6. Test Configurations
Results for the following configurations are provided in this report:
Channel Frequency
Operational
Data Rate with
(MHz)
Mode(s)
Highest Power
(GFSK)
MBit/s
Low
Mid
High
2440.00
2480.00
2400 - 2483.5 MHz
GFSK
1.00
2402.00
5.7. Equipment Modifications
The following modifications were required to bring the equipment into compliance:
1. NONE
5.8. Deviations from the Test Standard
The following deviations from the test standard were required in order to complete the test program:
1. NONE
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
15 of 62
6. TEST SUMMARY
List of Measurements
Test Header
Result
Data Link
15.247(a)(2) 6 dB & 99% Bandwidth
Complies
View Data
15.247(b), 15.31(e) Conducted Output Power
Complies
View Data
(i) Conducted Spurious Emissions
Complies
View Data
(ii) Conducted Band-Edge Emissions
Complies
View Data
Complies
View Data
(i) 15.205 Restricted Band Emissions
Complies
View Data
(ii) 15.205 Restricted Band-Edge Emissions
Complies
View Data
Conducted Results
15.247(d) Emissions
(1) Conducted Emissions
15.247(e) Power Spectral Density
Radiated Emissions
Digital Emissions
(3) 15.209 Digital Emissions (0.03 - 1 GHz)
AC Wireline
See Report HWPD85-G4
Complies
See Report HWPD85-G4
15.207 AC Wireline Emissions
Complies
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
16 of 62
7. TEST EQUIPMENT CONFIGURATION(S)
7.1. Conducted
Conducted RF Emission Test Set-up(s)
The following tests were performed using the conducted test set-up shown in the diagram below.
1. 6 dB & 99% Bandwidth
2. Peak Output Power
3. Power Spectral Density- Peak
4. Conducted Low Band-Edge Emission - Peak
5. Conducted Spurious Emissions - Peak
6. Conducted High Band-Edge Emission - Peak
A full system calibration was performed on the test station and any resulting system losses (or gains)
were taken into account in the production of all final measurement data.
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Asset#
Description
127
Power Supply
158
Barometer/Thermometer
248
287
376
378
Resistance
Thermometer
Rohde & Schwarz 40
GHz Receiver
USB 10MHz - 18GHz
Average Power Sensor
Rohde & Schwarz 40
GHz Receiver with
Generator
381
4x4 RF Switch Box
419
Laptop with Labview
Software
420
USB to GPIB Interface
440
442
445
460
461
493
494
74
RF#2
GPIB#1
RF#2
SMA#1
RF#2
SMA#2
RF#2
SMA#3
RF#2
SMA#4
RF#2
SMA#SA
RF#2
USB#1
USB Wideband Power
Sensor
USB Wideband Power
Sensor
PoE Injector
Dell Computer
Spectrum Analyzer
USB Wideband Power
Sensor
USB Wideband Power
Sensor
Environmental Chamber
Chamber 3
GPIB cable to Power
Supply
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
17 of 62
Calibration
Due Date
Cal when
used
Manufacturer
Model#
Serial#
HP
6674A
US36370530
Control
Company
4196
E2846
01 Dec 2016
Thermotronics
GR2105-02
9340 #1
21 Oct 2017
Rhode &
Schwarz
ESIB40
100201
02 May 2017
Agilent
U2000A
MY51440005
23 Oct 2017
Rhode &
Schwarz
ESIB40
100107/040
04 Aug 2017
MiCOM Labs
MiTest RF
Switch Box
MIC002
18 Nov 2016
Lenova
W520
TS02
Not Required
National
Instruments
GPIB-USB HS
1346738
Not Required
Boonton
55006
9178
25 Dec 2016
Boonton
55006
9181
06 Oct 2017
D-Link
Dell
Agilent
DPE-101GL
Optiplex330
E4440A
Boonton
55006
9634
10 Mar 2017
Boonton
55006
9726
10 Mar 2017
Tenney
TTC
12808-1
29 Sep 2017
HP
GPIB
None
Not Required
None
18 Nov 2016
None
18 Nov 2016
None
18 Nov 2016
None
18 Nov 2016
None
18 Nov 2016
None
Not Required
EUT to Mitest box port 1
Flexco
EUT to Mitest box port 2
Flexco
EUT to Mitest box port 3
Flexco
EUT to Mitest box port 4
Flexco
Mitest box to SA
Flexco
USB Cable to Mitest
Box
Dynex
SMA Cable
port1
SMA Cable
port2
SMA Cable
port3
SMA Cable
port4
SMA Cable
SA
USB Cable
QTAH1E2000625 Not Required
BC944G1
Not Required
MY46185537
13 Aug 2017
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
18 of 62
7.2. Radiated Emissions - 3m Chamber
The following tests were performed using the radiated test set-up shown in the diagram below.
Radiated emissions below 1GHz.
Radiated Emissions above 1GHz.
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
19 of 62
A full system calibration was performed on the test station and any resulting system losses (or gains)
were taken into account in the production of all final measurement data.
Asset#
Description
Manufacturer
Model#
Serial#
Calibration
Due Date
158
Barometer/Thermometer
Control
Company
4196
E2846
01 Dec 2016
Panasonic
WV-CU101
04R08507
Not Required
Rhode &
Schwarz
ESIB40
100201
02 May 2017
Microtronics
RBC50704
001
16 Aug 2017
Microtronics
BRC50703
002
16 Aug 2017
Microtronics
BRC50705
003
16 Aug 2017
Staco Energy
Co
3PN1020B
0546
Cal when used
EMCO
EMCO 6502
00060498
26 Sep 2017
Sunol
JB3
A052907
15 Aug 2017
EWT
EWT
EWT
EWT
EWT
EWT-14-0199
EWT-14-0203
EWT-14-0200
EWT-14-0201
EWT-14-0202
H1
H1
H1
H1
H1
16 Aug 2017
16 Aug 2017
16 Aug 2017
16 Aug 2017
16 Aug 2017
EWT
EWT-57-0112
H1
16 Aug 2017
Fluke
Fluke 26
series III
76080720
26 Oct 2017
Microtronics
BRM50716
034
16 Aug 2017
Rhode &
Schwarz
ESIB40
100107/040
04 Aug 2017
Microcircuits
VLFX-1050
N/A
16 Aug 2017
Microtronics
BRM50701
Amp 10 - 2500
MHz
001
16 Aug 2017
NA
09 Jun 2017
3117
00154575
10 Jan 2017
0406
09 Jun 2017
WS38
Not Required
170
287
301
302
303
330
336
338
341
342
343
344
345
346
373
Video System Controller
for Semi Anechoic
Chamber
Rohde & Schwarz 40
GHz Receiver
5470 to 5725 MHz
Notch Filter
5150 to 5350 MHz
Notch Filter
5725 to 5875 MHz
Notch filter
Variac 0-280 Vac
Active loop Ant 10kHz to
30 MHz
Sunol 30 to 3000 MHz
Antenna
900MHz Notch Filter
2.4 GHz Notch Filter
5.15 GHz Notch Filter
5.35 GHz Notch Filter
5.46 GHz Notch Filter
1.6 TO 10GHz High
Pass Filter
26III RMS Multimeter
396
Band Rejection Filter
5150 to 5880MHz
Rohde & Schwarz 40
GHz Receiver with
Generator
DC - 1050 MHz Low
Pass Filter
2.4 GHz Notch Filter
397
Amp 10 - 2500MHz
377
378
393
399
406
410
ETS 1-18 GHz Horn
Antenna
Amplifier for Radiated
Emissions
Desktop Computer
MiCOM Labs
ETS
MiCOM Labs
Dell
40dB 1 to
18GHz Amp
Inspiron 620
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
411
Mast/Turntable
Controller
412
USB to GPIB Interface
413
414
Mast Controller
DC Power Supply 0-60V
415
Turntable Controller
416
Gigabit ethernet filter
447
Rad Emissions Test
Software
462
463
464
465
466
467
468
469
470
476
480
481
482
502
87
VLF-1700
Schwarzbeck cable from
Antenna to Amplifier.
Schwarzbeck cable from
Amplifier to Bulkhead.
Schwarzbeck cable from
Bulkhead to Receiver
Low Pass Filter DC1000 MHz
Low Pass Filter DC1500 MHz
2495 to 2650 MHz notch
filter
Low pass filter
Low pass filter
High Pass filter
Low Pass dc-2200MHz
filter
Cable - Bulkhead to
Amp
Cable - Bulkhead to
Receiver
Cable - Amp to Antenna
Test Software for
Radiated Emissions
Uninterruptible Power
Supply
Low pass filter DC-1700
MHz
Sunol Sciences
National
Instruments
Sunol Science
HP
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
20 of 62
SC98V
060199-1D
Not Required
GPIB-USB HS
11B8DC2
Not Required
030801-3
1029A01285
Not Required
Cal when used
None
Not Required
None
Not Required
447
Not Required
TWR95-4
6274
Turntable
Sunol Sciences
Controller
Gigafoil
ETS-Lingren
260366
Rad
Emissions
Test Software
MiCOM
Version
1.0.109
Schwarzbeck
AK 9513
462
31 May 2017
Schwarzbeck
AK 9513
463
31 May 2017
Schwarzbeck
AK 9513
464
31 May 2017
Mini-Circuits
NLP-1200+
VUU01901402
02 Jun 2017
Mini-Circuits
NLP-1750+
VUU10401438
02 Jun 2017
MicroTronics
BRM50709
011
16 Aug 2017
Mini Circuits
Mini Circuit
Mini Circuits
SLP-550
SLP-1000
SHP-700
15542 NLP2400+
157-1573050360
151-1513050787
157-1573051574
None
None
None
16 Aug 2017
16 Aug 2017
16 Aug 2017
VUU13801345
16 Aug 2017
480
02 Jun 2017
481
02 Jun 2017
482
02 Jun 2017
Version 5 Build
59
Not Required
F3471 02/01
Cal when used
None
31 May 2017
Mini Circuits
SRC Haverhill
SRC Haverhill
SRC Haverhill
EMISoft
Vasona
Falcon Electric ED2000-1/2LC
Mini Circuits
VLF-1700
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
21 of 62
8. MEASUREMENT AND PRESENTATION OF TEST DATA
The measurement and graphical data presented in this test report was generated automatically using
state-of-the-art technology creating an easy to read report structure. Numerical measurement data is
separated from supporting graphical data (plots) through hyperlinks. Numerical measurement data can
be reviewed without scrolling through numerous graphical pages to arrive at the next data matrix.
Plots have been relegated into the Appendix ‘Graphical Data’.
Test and report automation was performed by MiTest. MiTest is an automated test system developed by
MiCOM Labs. MiTest is the first cloud based modular test system enabling end-to-end automation of
regulatory compliance testing.
The MiCOM Labs “MiTest” Automated Test System“ (Patent Pending)
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
22 of 62
9. TEST RESULTS
9.1. 6 dB & 99% Bandwidth
Conducted Test Conditions for 6 dB and 99% Bandwidth
Standard: FCC CFR 47:15.247
Test Heading: 6 dB and 99 % Bandwidth
Standard Section(s): 15.247 (a)(2)
Ambient Temp. (ºC): 24.0 - 27.5
Rel. Humidity (%): 32 - 45
Pressure (mBars): 999 - 1001
Reference Document(s): See Normative References
Test Procedure for 6 dB and 99% Bandwidth Measurement
The bandwidth at 6 dB and 99 % was measured with a spectrum analyzer connected to the antenna terminal, while EUT is operating
in transmission mode at the appropriate center frequency.
Testing was performed under ambient conditions at nominal voltage. Where the device operated with multiple antenna ports i.e.
MIMO device, each port was measured and reported.
Test configuration and setup used for the measurement was per the Conducted Test Set-up specified in this document.
Limits for 6 dB and 99% Bandwidth
(a) Operation under the provisions of this Section is limited to frequency hopping and digitally modulated intentional radiators
that comply with the following provisions:
(2) Systems using digital modulation techniques may operate in the 902-928 MHz and 2400-2483.5 MHz bands. The
minimum 6 dB bandwidth shall be at least 500 kHz.
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
23 of 62
Equipment Configuration for 6 dB & 99% Bandwidth
Duty Cycle (%): 99
Variant: GFSK
Data Rate: 1.00 MBit/s
Antenna Gain (dBi): Not Applicable
Modulation: GFSK
Beam Forming Gain (Y)(dB): Not Applicable
TPC: Not Applicable
Tested By: CC
Engineering Test Notes: None
Test Measurement Results
Measured 6 dB Bandwidth (MHz)
Test
Frequency
Port(s)
6 dB Bandwidth (MHz)
Limit
Lowest
Margin
MHz
Highest
Lowest
KHz
MHz
2402.0
0.709
≥500.0
-0.21
0.709
≥500.0
-0.21
0.709
----
0.709
2480.0
----
0.709
0.709
----
0.709
2440.0
0.709
0.709
≥500.0
-0.21
Measured 99% Bandwidth (MHz)
Test
Frequency
Port(s)
MHz
2402.0
1.074
2440.0
1.078
2480.0
1.078
----
----
----
Maximum
99%
Bandwidth
(MHz)
1.074
1.078
1.078
Traceability to Industry Recognized Test Methodologies
Work Instruction: WI-03 MEASURING RF SPECTRUM MASK
Measurement Uncertainty: ±2.81 dB
Note: click the links in the above matrix to view the graphical image (plot).
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
24 of 62
9.2. Conducted Output Power
Conducted Test Conditions for Fundamental Emission Output Power
Standard: FCC CFR 47:15.247
Test Heading: Output Power
Standard Section(s): 15.247 (b) & (c)
Ambient Temp. (ºC): 24.0 - 27.5
Rel. Humidity (%): 32 - 45
Pressure (mBars): 999 - 1001
Reference Document(s): See Normative References
Test Procedure for Fundamental Emission Output Power Measurement
In the case of average power measurements an average power sensor was utilized.
For peak power measurements the spectrum analyzer built-in power function was used to integrate peak power over the 20 dB
bandwidth.
Testing was performed under ambient conditions at nominal voltage only. Where the device operated with multiple antenna ports i.e.
MIMO device, each port was measured, summed (Σ) and reported.
Test configuration and setup used for the measurement was per the Conducted Test Set-up specified in this document.
Supporting Information
Calculated Power = A + G + Y+ 10 log (1/x) dBm
A = Total Power [10*Log10 (10a/10 + 10b/10 + 10c/10 + 10d/10)]
G = Antenna Gain
Y = Beamforming Gain
x = Duty Cycle (average power measurements only)
Limits for Fundamental Emission Output Power
(b) The maximum peak conducted output power of the intentional radiator shall not exceed the following for non-frequency hopping
systems:
(3) For systems using digital modulation in the 902-928 MHz and 2400-2483.5 MHz bands: 1 Watt. As an alternative to a peak
power measurement, compliance with the one Watt limit can be based on a measurement of the maximum conducted output
power. Maximum Conducted Output Power is defined as the total transmit power delivered to all antennas and antenna
elements averaged across all symbols in the signaling alphabet when the transmitter is operating at its maximum power control
level. Power must be summed across all antennas and antenna elements. The average must not include any time intervals
during which the transmitter is off or is transmitting at a reduced power level. If multiple modes of operation are possible (e.g.,
alternative modulation methods), the maximum conducted output power is the highest total transmit power occurring in any
mode.
(4) The conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional
gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section, if transmitting antennas of directional gain
greater than 6 dBi are used, the conducted output power from the intentional radiator shall be reduced below the stated values
in paragraphs (b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the antenna exceeds 6 dBi.
(c) Operation with directional antenna gains greater than 6 dBi.
(1) Fixed point-to-point operation:
(i) Systems operating in the 2400-2483.5 MHz band that are used exclusively for fixed, point-to-point operations may
employ transmitting antennas with directional gain greater than 6 dBi provided the maximum conducted output power of
the intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6 dBi.
(iii) Fixed, point-to-point operation, as used in paragraphs (c)(1)(i) and (c)(1)(ii) of this section, excludes the use of point-tomultipoint systems, omnidirectional applications, and multiple co-located intentional radiators transmitting the same
information. The operator of the spread spectrum or digitally modulated intentional radiator or, if the equipment is
professionally installed, the installer is responsible for ensuring that the system is used exclusively for fixed, point-to-point
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
25 of 62
operations. The instruction manual furnished with the intentional radiator shall contain language in the installation
instructions informing the operator and the installer of this responsibility.
(2) In addition to the provisions in paragraphs (b)(3), (b)(4) and (c)(1)(i) of this section, transmitters operating in the 2400-2483.5
MHz band that emit multiple directional beams, simultaneously or sequentially, for the purpose of directing signals to individual
receivers or to groups of receivers provided the emissions comply with the following:
(i) Different information must be transmitted to each receiver.
(ii) If the transmitter employs an antenna system that emits multiple directional beams but does not do emit multiple
directional beams simultaneously, the total output power conducted to the array or arrays that comprise the device, i.e.,
the sum of the power supplied to all antennas, antenna elements, staves, etc. and summed across all carriers or frequency
channels, shall not exceed the limit specified in paragraph (b)(1) or (b)(3) of this section, as applicable. However, the total
conducted output power shall be reduced by 1 dB below the specified limits for each 3 dB that the directional gain of the
antenna/antenna array exceeds 6 dBi. The directional antenna gain shall be computed as follows:
(A) The directional gain shall be calculated as the sum of 10 log (number of array elements or staves) plus the
directional gain of the element or stave having the highest gain.
(B) A lower value for the directional gain than that calculated in paragraph (c)(2)(ii)(A) of this section will be accepted
if sufficient evidence is presented, e.g., due to shading of the array or coherence loss in the beamforming.
(iii) If a transmitter employs an antenna that operates simultaneously on multiple directional beams using the same or
different frequency channels, the power supplied to each emission beam is subject to the power limit specified in
paragraph (c)(2)(ii) of this section. If transmitted beams overlap, the power shall be reduced to ensure that their aggregate
power does not exceed the limit specified in paragraph (c)(2)(ii) of this section. In addition, the aggregate power
transmitted simultaneously on all beams shall not exceed the limit specified in paragraph (c)(2)(ii) of this section by more
than 8 dB.
(iv) Transmitters that emit a single directional beam shall operate under the provisions of paragraph (c)(1) of this section.
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
26 of 62
Equipment Configuration for Peak Output Power
Duty Cycle (%): 99.0
Variant: GFSK
Data Rate: 1.00 MBit/s
Antenna Gain (dBi): 3.2
Modulation: GFSK
Beam Forming Gain (Y)(dB): Not Applicable
TPC: Not Applicable
Tested By: CC
Engineering Test Notes: None
Test Measurement Results
Measured Output Power (dBm)
Test
Frequency
Port(s)
MHz
2402.0
0.91
2440.0
0.92
2480.0
0.93
----
----
----
Calculated
Total Power
Σ Port(s)
dBm
Limit
Margin
EUT Power
Setting
dBm
dB
0.91
30.00
-29.09
4.00
0.92
30.00
-29.08
4.00
0.93
30.00
-29.07
4.00
Traceability to Industry Recognized Test Methodologies
Work Instruction: WI-01 MEASURING RF OUTPUT POWER
Measurement Uncertainty: ±1.33 dB
The above measurements are true pulse readings and therefore a Duty Cycling correction factor is not required.
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
27 of 62
9.3 Conducted Spurious Emissions
9.3.1 Conducted Emissions
Conducted Test Conditions for Transmitter Conducted Spurious and Band-Edge Emissions
Standard: FCC CFR 47:15.247
Test Heading: Max Unwanted Emission Levels
Standard Section(s): 15.247 (d)
Ambient Temp. (ºC): 24.0 - 27.5
Rel. Humidity (%): 32 - 45
Pressure (mBars): 999 - 1001
Reference Document(s): See Normative References
Test Procedure for Transmitter Conducted Spurious and Band-Edge Emissions Measurement
Transmitter Conducted Spurious and Band-Edge emissions were measured at a limit of 30 dBc (average detector) or 20 dBc (peak
detector) below the highest in-band spectral density measured with a spectrum analyzer connected to the antenna terminal.
Measurements were made while EUT was operating in transmit mode of operation at the appropriate centre frequency closest to the
band-edge. Emissions were maximized during the measurement and limits derived from the peak spectral power and drawn on each
plot.
Where the device operated with multiple antenna ports i.e. MIMO device, each port was measured separately. Testing was
performed under ambient conditions at nominal voltage only.
Test configuration and setup used for the measurement was per the Conducted Test Set-up specified in this document.
Limits Transmitter Conducted Spurious and Band-Edge Emissions
(d) In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is
operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz
bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated
measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies
with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this
section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified
in §15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also
comply with the radiated emission limits specified in §15.209(a) (see §15.205(c)).
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
28 of 62
Title:
To:
Serial #:
Issue Date:
Page:
Equipment Configuration for Transmitter Conducted Spurious Emissions
Duty Cycle (%): 99
Variant: GFSK
Data Rate: 1.00 MBit/s
Antenna Gain (dBi): 3.2
Modulation: GFSK
Beam Forming Gain (Y): Not Applicable
TPC: Not Applicable
Tested By: CC
Engineering Test Notes: None
Test Measurement Results
Transmitter Conducted Spurious Emissions (dBm)
Test
Frequency
Frequency
Range
MHz
MHz
SE
Limit
SE
Limit
SE
Limit
SE
Limit
2402.0
30.0 - 26000.0
-40.504
-20.00
2440.0
30.0 - 26000.0
-40.618
-20.00
2480.0
330.0 - 26000.0 -41.206
-22.00
----
----
----
----
----
----
Port a
Port b
Port c
Port d
Traceability to Industry Recognized Test Methodologies
Work Instruction: WI-05 MEASUREMENT OF SPURIOUS EMISSIONS
Measurement Uncertainty: <=40 GHz ±2.37 dB, > 40 GHz ±4.6 dB
Note: click the links in the above matrix to view the graphical image (plot).
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
29 of 62
9.3.2 Conducted Band-Edge Emissions
Low Band-Edge Emissions
Equipment Configuration for Conducted Low Band-Edge Emissions - Peak
Duty Cycle (%): 99.0
Variant: GFSK
Data Rate: 1.00 MBit/s
Antenna Gain (dBi): 3.2
Modulation: GFSK
Beam Forming Gain (Y)(dB): Not Applicable
TPC: Not Applicable
Tested By: CC
Engineering Test Notes: None
Test Measurement Results
Channel
2402.0 MHz
Frequency:
Band-Edge
2400.0 MHz
Frequency:
Test Frequency
2350.0 - 2405.0 MHz
Range:
Band-Edge Markers and Limit
Port(s)
M1 Amplitude
M2 Frequency
Plot Limit (dBm)
(dBm)
(MHz)
-39.98
-19.00
2401.40
Revised Limit
Amplitude
M2A Frequency
(dBm)
(MHz)
--
--
Margin
(MHz)
-1.400
Traceability to Industry Recognized Test Methodologies
Work Instruction: WI-05 MEASUREMENT OF SPURIOUS EMISSIONS
Measurement Uncertainty: <=40 GHz ±2.37 dB, > 40 GHz ±4.6 dB
Note: click the links in the above matrix to view the graphical image (plot).
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
30 of 62
High Band-Edge Emissions
Equipment Configuration for Conducted High Band-Edge Emissions - Peak
Duty Cycle (%): 99.0
Variant: GFSK
Data Rate: 1.00 MBit/s
Antenna Gain (dBi): Not Applicable
Modulation: GFSK
Beam Forming Gain (Y)(dB): Not Applicable
TPC: Not Applicable
Tested By: CC
Engineering Test Notes: None
Test Measurement Results
Channel
2480.0 MHz
Frequency:
Band-Edge
2483.5 MHz
Frequency:
Test Frequency
2475.0 - 2524.0 MHz
Range:
Band-Edge Markers and Limit
Port(s)
M3 Amplitude
M2 Frequency
Plot Limit (dBm)
(dBm)
(MHz)
-46.65
-20.00
2480.60
Revised Limit
Amplitude
M2A Frequency
(dBm)
(MHz)
--
--
Margin
(MHz)
-2.900
Traceability to Industry Recognized Test Methodologies
Work Instruction: WI-05 MEASUREMENT OF SPURIOUS EMISSIONS
Measurement Uncertainty: <=40 GHz ±2.37 dB, > 40 GHz ±4.6 dB
Note: click the links in the above matrix to view the graphical image (plot).
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
31 of 62
9.4 Power Spectral Density
Conducted Test Conditions for Power Spectral Density
Standard: FCC CFR 47:15.247
Test Heading: Power Spectral Density
Standard Section(s): 15.247 (e)
Ambient Temp. (ºC): 24.0 - 27.5
Rel. Humidity (%): 32 - 45
Pressure (mBars): 999 - 1001
Reference Document(s): See Normative References
Test Procedure for Power Spectral Density
The transmitter output was connected to a spectrum analyzer and the measured made in a 3 kHz resolution bandwidth using the
analyzer auto-coupled sweep-time. A peak value was found over the full emission bandwidth and the spectrum downloaded for post
processing purposes.
Where the device operated with multiple antenna ports i.e. MIMO device, each port was measured separately. The Peak Power
Spectral Density is the highest level found across the emission bandwidth. With multiple antenna port measurements the numerical
analyzer data from each port is summed (å) and a link to this additional graphic is provided.
Testing was performed under ambient conditions at nominal voltage only.
Test configuration and setup used for the measurement was per the Conducted Test Set-up specified in this document.
Measure and sum the spectra across the outputs. With this technique, spectra are measured at each output of the device at the
required resolution bandwidth. The individual spectra are then summed mathematically in linear power units. Unlike in-band power
measurements, in which the sum involves a single measured value (output power) from each output, measurements for compliance
with PSD limits involve summing entire spectra across corresponding frequency bins on the various outputs. Consistency is
maintained for any device with multiple transmitter outputs to be certain the individual outputs are all aligned with the same span and
same number of points. In this instance, the linear power spectrum value within the first spectral bin of output 0 is summed with that in
the first spectral bin of output 1, and the first spectral bin of output 2, and so on up to the Nth output to obtain the true value for the
first frequency bin of the summed spectrum. The summed spectrum value for each frequency bin is computed in this fashion. These
summed spectral values were post processed and the resulting numerical and graphical data presented.
NOTE:
It may be observed that the spectrum in some antenna port plots break the limit line however this in itself does NOT constitute a
failure. In all cases a spectrum summation plot is provided in order to prove compliance. A failure occurs only after the summation
of all spectrum plots have been summed and are found to be greater than the limit line.
Supporting Information
Calculated Power = A + 10 log (1/x) dBm
A = Total Power Spectral Density [10 Log10 (10a/10 + 10b/10 + 10c/10 + 10d/10)]
x = Duty Cycle
Limits Power Spectral Density
For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater
than +8 dBm in any 3 kHz band during any time interval of continuous transmission. This power spectral density shall be determined
in accordance with the provisions of paragraph (b) of this section. The same method of determining the conducted output power shall
be used to determine the power spectral density.
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
32 of 62
Equipment Configuration for Power Spectral Density - Peak
Duty Cycle (%): 99.0
Variant: GFSK
Data Rate: 1.00 MBit/s
Antenna Gain (dBi): 3.2
Modulation: GFSK
Beam Forming Gain (Y)(dB): Not Applicable
TPC: Not Applicable
Tested By: CC
Engineering Test Notes: None
Test Measurement Results
Measured Power Spectral Density
Test
Frequency
Port(s) (dBm/3KHz)
Amplitude
Summation
Limit
Margin
MHz
dBm/3KHz
dBm/3KHz
dB
2402.0
-11.230
-19.2
-12.802
-12.802
8.0
-20.8
-12.996
----
8.0
2480.0
----
-11.230
2440.0
----
-12.996
8.0
-21.0
Traceability to Industry Recognized Test Methodologies
Work Instruction: WI-03 MEASURING RF SPECTRUM MASK
Measurement Uncertainty: ±2.81 dB
Note: click the links in the above matrix to view the graphical image (plot).
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
33 of 62
9.5 Radiated Emissions
Radiated Test Conditions for Radiated Spurious and Band-Edge Emissions (Restricted Bands)
FCC CFR 47 Part 15 Subpart C
15.247 (DTS)
Radiated Spurious and BandTest Heading:
Edge Emissions
Standard:
Standard Section(s): 15.205, 15.209
Ambient Temp. (ºC): 20.0 - 24.5
Rel. Humidity (%): 32 - 45
Pressure (mBars): 999 - 1001
Reference Document(s): See Normative References
Test Procedure for Radiated Spurious and Band-Edge Emissions (Restricted Bands)
Radiated emissions for restricted bands above 1 GHz are measured in the anechoic chamber at a 3-meter distance on every azimuth
in both horizontal and vertical polarities. The emissions are recorded and maximized as a function of azimuth by rotation through
360° with a spectrum analyzer in peak hold mode. Depending on the frequency band spanned a notch filter and waveguide filter was
used to remove the fundamental frequency. The highest emissions relative to the limit are listed for each frequency spanned.
Measurements on any restricted band frequency or frequencies above 1 GHz are based on the use of measurement instrumentation
employing peak and average detectors. All measurements were performed using a resolution bandwidth of 1 MHz.
Test configuration and setup for Radiated Spurious and Band-Edge Measurement were per the Radiated Test Set-up specified in this
document.
Limits for Restricted Bands
Peak emission: 74 dBuV/m
Average emission: 54 dBuV/m
Field Strength Calculation
The field strength is calculated by adding the Antenna Factor and Cable Loss, and subtracting Amplifier Gain from the measured
reading. All factors are included in the reported data.
FS = R + AF + CORR - FO
where:
FS = Field Strength
R = Measured Spectrum analyzer Input Amplitude
AF = Antenna Factor
CORR = Correction Factor = CL – AG + NFL
CL = Cable Loss
AG = Amplifier Gain
FO = Distance Falloff Factor
NFL = Notch Filter Loss or Waveguide Loss
Example:
Given receiver input reading of 51.5 dBmV; Antenna Factor of 8.5 dB; Cable Loss of 1.3 dB; Falloff Factor of 0 dB, an Amplifier Gain
of 26 dB and Notch Filter Loss of 1 dB. The Field Strength (FS) of the measured emission is:
FS = 51.5 + 8.5 + 1.3 - 26.0 +1 = 36.3 dBmV/m
Conversion between dBmV/m (or dBmV) and mV/m (or mV) are as follows:
Level (dBmV/m) = 20 * Log (level (mV/m))
40 dBmV/m = 100 mV/m
48 dBmV/m = 250 mV/m
Restricted Bands of Operation (15.205)
(a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed
below:
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
34 of 62
Frequency Band
MHz
MHz
MHz
GHz
0.090-0.110
16.42-16.423
399.9-410
4.5-5.15
0.495-0.505
16.69475-16.69525
608-614
5.35-5.46
2.1735-2.1905
16.80425-16.80475
960-1240
7.25-7.75
4.125-4.128
25.5-25.67
1300-1427
8.025-8.5
4.17725-4.17775
37.5-38.25
1435-1626.5
9.0-9.2
4.20725-4.20775
73-74.6
1645.5-1646.5
9.3-9.5
6.215-6.218
74.8-75.2
1660-1710
10.6-12.7
6.26775-6.26825
108-121.94
1718.8-1722.2
13.25-13.4
6.31175-6.31225
123-138
2200-2300
14.47-14.5
8.291-8.294
149.9-150.05
2310-2390
15.35-16.2
8.362-8.366
156.52475-156.52525
2483.5-2500
17.7-21.4
8.37625-8.38675
156.7-156.9
2690-2900
22.01-23.12
8.41425-8.41475
162.0125-167.17
3260-3267
23.6-24.0
12.29-12.293
167.72-173.2
3332-3339
31.2-31.8
12.51975-12.52025
240-285
3345.8-3358
36.43-36.5
12.57675-12.57725
322-335.4
3600-4400
Above 38.6
13.36-13.41
(b) Except as provided in paragraphs (d) and (e) of this section, the field strength of emissions appearing within these frequency
bands shall not exceed the limits shown in §15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in
§15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz,
compliance with the emission limits in §15.209 shall be demonstrated based on the average value of the measured emissions. The
provisions in §15.35 apply to these measurements.
(c) Except as provided in paragraphs (d) and (e) of this section, regardless of the field strength limits specified elsewhere in this
subpart, the provisions of this section apply to emissions from any intentional radiator.
(d) The following devices are exempt from the requirements of this section:
(1) Swept frequency field disturbance sensors operating between 1.705 and 37 MHz provided their emissions only sweep
through the bands listed in paragraph (a) of this section, the sweep is never stopped with the fundamental emission within the
bands listed in paragraph (a) of this section, and the fundamental emission is outside of the bands listed in paragraph (a) of this
section more than 99% of the time the device is actively transmitting, without compensation for duty cycle.
(2) Transmitters used to detect buried electronic markers at 101.4 kHz which are employed by telephone companies.
(3) Cable locating equipment operated pursuant to §15.213.
(4) Any equipment operated under the provisions of §15.253, 15.255, and 15.256 in the frequency band 75-85 GHz, or §15.257
of this part.
(5) Biomedical telemetry devices operating under the provisions of §15.242 of this part are not subject to the restricted band
608-614 MHz but are subject to compliance within the other restricted bands.
(6) Transmitters operating under the provisions of subparts D or F of this part.
(7) Devices operated pursuant to §15.225 are exempt from complying with this section for the 13.36-13.41 MHz band only.
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
35 of 62
(8) Devices operated in the 24.075-24.175 GHz band under §15.245 are exempt from complying with the requirements of this
section for the 48.15-48.35 GHz and 72.225-72.525 GHz bands only, and shall not exceed the limits specified in §15.245(b).
(9) Devices operated in the 24.0-24.25 GHz band under §15.249 are exempt from complying with the requirements of this
section for the 48.0-48.5 GHz and 72.0-72.75 GHz bands only, and shall not exceed the limits specified in §15.249(a).
(e) Harmonic emissions appearing in the restricted bands above 17.7 GHz from field disturbance sensors operating under the
provisions of §15.245 shall not exceed the limits specified in §15.245(b).
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
9.5.1
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
36 of 62
Restricted Band Emissions
Equipment Configuration for TX Spurious & Restricted Band Emissions
Variant: GFSK
Antenna: Aruba Metal sheet
Antenna Gain (dBi): 3.2
Modulation: GFSK
Beam Forming Gain (Y): Not Applicable
Duty Cycle (%): 99
Channel Frequency (MHz): 2402.00
Data Rate: 1.00 MBit/s
Power Setting: 4
Tested By: JMH
Test Measurement Results
1000.00 - 18000.00 MHz
Num
Frequency
MHz
Raw
dBμV
Cable AF dB
Level Measurement
Pol
Hgt cm
Loss
dBμV/m
Type
dB
#1
7205.55
48.49
4.26
-7.35
45.40
Peak (NRB) Vertical
101
Test Notes: EUT on 150 cm table powered by host laptop via CC debugger.
Azt
Deg
Limit
Margin
dBμV/m
dB
--
--
Pass
/Fail
Pass
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
37 of 62
Equipment Configuration for TX Spurious & Restricted Band Emissions
Variant: GFSK
Antenna: Aruba Metal sheet
Antenna Gain (dBi): 3.2
Modulation: GFSK
Beam Forming Gain (Y): Not Applicable
Duty Cycle (%): 99
Channel Frequency (MHz): 2440.00
Data Rate: 1.00 MBit/s
Power Setting: 4
Tested By: JMH
Test Measurement Results
1000.00 - 18000.00 MHz
Num
Frequency
MHz
Raw
dBμV
#1
7319.24
55.14
Cable
Loss
dB
4.26
AF dB
Pol
Hgt
cm
Azt
Deg
Horizontal
134
74.0
-21.9
Pass
#2
7319.24
44.75
4.26
-7.27
41.74
Max Avg
Horizontal
Test Notes: EUT on 150 cm table powered by host laptop via CC debugger.
134
54.0
-12.3
Pass
-7.27
Level Measurement
dBμV/m
Type
52.13
Max Peak
Limit Margin
dBμV/m
dB
Pass
/Fail
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
38 of 62
Equipment Configuration for TX Spurious & Restricted Band Emissions
Variant: GFSK
Antenna: Aruba Metal sheet
Antenna Gain (dBi): 3.2
Modulation: GFSK
Beam Forming Gain (Y): Not Applicable
Duty Cycle (%): 99
Channel Frequency (MHz): 2480.00
Data Rate: 1.00 MBit/s
Power Setting: 4
Tested By: JMH
Test Measurement Results
1000.00 - 18000.00 MHz
Num
Frequency
MHz
Raw
dBμV
#1
7439.43
52.57
Cable
Loss
dB
4.31
AF dB
-7.13
Level Measurement
dBμV/m
Type
49.75
Max Peak
#2
7439.43
42.04
4.31
-7.13
39.22
Max Avg
Test Notes: EUT on 150 cm table powered by host laptop via CC debugger.
Pol
Hgt cm
Azt
Deg
Limit
Margin
dBμV/m
dB
Pass
/Fail
Vertical
138
340
74.0
-24.3
Pass
Vertical
138
340
54.0
-14.8
Pass
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
9.5.2
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
39 of 62
Restricted Band-Edge Emissions
Aruba Metal sheet
Band-Edge Freq
Limit 74.0dBµV/m
Limit 54.0dBµV/m
Power Setting
Operational Mode
Operating
Frequency (MHz)
MHz
dBµV/m
dBµV/m
GFSK
2402.00
2390.00
60.90
46.16
GFSK
2480.00
2483.50
61.35
48.82
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
40 of 62
Equipment Configuration for Radiated - Lower Restricted Band-Edge Emissions
Variant: GFSK
Antenna: Aruba Metal sheet
Antenna Gain (dBi): 3.2
Modulation: GFSK
Beam Forming Gain (Y): Not Applicable
Duty Cycle (%): 99
Channel Frequency (MHz): 2402.00
Data Rate: 1.00 MBit/s
Power Setting: 4
Tested By: JMH
Test Measurement Results
2310.00 - 2410.00 MHz
Num
Frequency
MHz
Raw
dBμV
AF dB
26.24
Cable
Loss
dB
2.69
#1
2382.16
#2
2390.00
Level Measurement
dBμV/m
Type
31.97
60.90
11.43
2.69
32.04
46.16
Max Peak
Max Avg
Restricted#3
2390.00
----Band
Test Notes: EUT on 150 cm table powered by host laptop via CC debugger.
Pol
Hgt cm
Azt
Deg
Limit
Margin
dBμV/m
dB
Pass
/Fail
Vertical
156
30
74.0
-13.1
Pass
Vertical
156
30
54.0
-7.8
Pass
--
--
--
--
--
--
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
41 of 62
Equipment Configuration for Radiated - Upper Restricted Band-Edge Emissions
Variant: GFSK
Antenna: Aruba Metal sheet
Antenna Gain (dBi): 3.2
Modulation: GFSK
Beam Forming Gain (Y): Not Applicable
Duty Cycle (%): 99
Channel Frequency (MHz): 2480.00
Data Rate: 1.00 MBit/s
Power Setting: 4
Tested By: JMH
Test Measurement Results
2472.00 - 2500.00 MHz
Num
Frequency
MHz
Raw
dBμV
AF dB
13.72
Cable
Loss
dB
2.73
#1
2483.50
#2
2483.50
Level Measurement
dBμV/m
Type
32.37
48.82
26.25
2.73
32.37
61.35
Max Avg
Max Peak
Restricted#3
2483.50
----Band
Test Notes: EUT on 150 cm table powered by host laptop via CC debugger.
Pol
Hgt cm
Azt
Deg
Limit
Margin
dBμV/m
dB
Pass
/Fail
Vertical
151
47
54.0
-5.2
Pass
Vertical
151
47
74.0
-12.7
Pass
--
--
--
--
--
--
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
42 of 62
A. APPENDIX - GRAPHICAL IMAGES
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
43 of 62
A.1. 6 dB & 99% Bandwidth
6 dB & 99% BANDWIDTH
Variant: GFSK, Channel: 2402.00 MHz, Chain a, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = MAX HOLD
M1 : 2401.649 MHz : -3.964 dBm
M2 : 2402.255 MHz : 2.073 dBm
Delta1 : 709 KHz : 0.189 dB
T1 : 2401.469 MHz : -11.838 dBm
T2 : 2402.543 MHz : -11.944 dBm
OBW : 1.074 MHz
Measured 6 dB Bandwidth: 0.709 MHz
Limit: ≥500.0 kHz
Margin: -0.21 MHz
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
44 of 62
6 dB & 99% BANDWIDTH
Variant: GFSK, Channel: 2440.00 MHz, Chain a, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = MAX HOLD
M1 : 2439.645 MHz : -4.861 dBm
M2 : 2440.251 MHz : 1.330 dBm
Delta1 : 709 KHz : 0.565 dB
T1 : 2439.465 MHz : -12.703 dBm
T2 : 2440.543 MHz : -12.719 dBm
OBW : 1.078 MHz
Measured 6 dB Bandwidth: 0.709 MHz
Limit: ≥500.0 kHz
Margin: -0.21 MHz
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
45 of 62
6 dB & 99% BANDWIDTH
Variant: GFSK, Channel: 2480.00 MHz, Chain a, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = MAX HOLD
M1 : 2479.645 MHz : -5.690 dBm
M2 : 2479.762 MHz : 0.362 dBm
Delta1 : 709 KHz : 0.212 dB
T1 : 2479.465 MHz : -13.669 dBm
T2 : 2480.543 MHz : -13.488 dBm
OBW : 1.078 MHz
Measured 6 dB Bandwidth: 0.709 MHz
Limit: ≥500.0 kHz
Margin: -0.21 MHz
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
46 of 62
A.2. Conducted Emissions
A.2.1 Conducted Spurious Emissions
CONDUCTED SPURIOUS EMISSIONS - PEAK
Variant: GFSK, Channel: 2402.00 MHz, Chain a, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = VIEW
M1 : 2371.984 MHz : 0.393 dBm
M2 : 6535.511 MHz : -40.504 dBm
Limit: -20.00 dBm
Margin: -20.50 dB
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
47 of 62
CONDUCTED SPURIOUS EMISSIONS - PEAK
Variant: GFSK, Channel: 2440.00 MHz, Chain a, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = VIEW
M1 : 2424.028 MHz : -0.551 dBm
M2 : 6951.864 MHz : -40.618 dBm
Limit: -20.00 dBm
Margin: -20.62 dB
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
48 of 62
CONDUCTED SPURIOUS EMISSIONS - PEAK
Variant: GFSK, Channel: 2480.00 MHz, Chain a, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = VIEW
M1 : 2476.072 MHz : -2.152 dBm
M2 : 6639.599 MHz : -41.206 dBm
Limit: -22.00 dBm
Margin: -19.21 dB
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
49 of 62
A.2.2 Conducted Band Edge Emissions
Low Band-Edge Emissions
CONDUCTED LOW BAND-EDGE EMISSION - PEAK
Variant: GFSK, Channel: 2402.00 MHz, Chain a, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = VIEW
M1 : 2400.000 MHz : -39.981 dBm
M2 : 2401.363 MHz : -20.427 dBm
M3 : 2402.355 MHz : 1.690 dBm
Channel Frequency: 2402.00 MHz
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
50 of 62
High Band-Edge Emissions
CONDUCTED HIGH BAND-EDGE EMISSION - PEAK
Variant: GFSK, Channel: 2480.00 MHz, Chain a, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = VIEW
M1 : 2480.204 MHz : 0.138 dBm
M2 : 2480.597 MHz : -15.989 dBm
M3 : 2483.500 MHz : -46.646 dBm
Channel Frequency: 2480.00 MHz
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
51 of 62
A.3. Power Spectral Density
POWER SPECTRAL DENSITY - PEAK
Variant: GFSK, Channel: 2402.00 MHz, Chain a, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = VIEW
M1 : 2402.104 MHz : -11.230 dBm
Limit: ≤ 8.000 dBm
Margin: 19.23 dB
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
52 of 62
POWER SPECTRAL DENSITY - PEAK
Variant: GFSK, Channel: 2402.00 MHz, SUM, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = VIEW
M1 : 2402.104 MHz : -11.230 dBm
Limit: ≤ 8.0 dBm
Margin: -19.2 dB
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
53 of 62
POWER SPECTRAL DENSITY - PEAK
Variant: GFSK, Channel: 2440.00 MHz, Chain a, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = VIEW
M1 : 2440.206 MHz : -12.802 dBm
Limit: ≤ 8.000 dBm
Margin: 20.80 dB
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
54 of 62
POWER SPECTRAL DENSITY - PEAK
Variant: GFSK, Channel: 2440.00 MHz, SUM, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = VIEW
M1 : 2440.206 MHz : -12.802 dBm
Limit: ≤ 8.0 dBm
Margin: -20.8 dB
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
55 of 62
POWER SPECTRAL DENSITY - PEAK
Variant: GFSK, Channel: 2480.00 MHz, Chain a, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = VIEW
M1 : 2480.026 MHz : -12.996 dBm
Limit: ≤ 8.000 dBm
Margin: 21.00 dB
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
56 of 62
POWER SPECTRAL DENSITY - PEAK
Variant: GFSK, Channel: 2480.00 MHz, SUM, Temp: 20, Voltage: 48 Vdc
Analyzer Setup
Marker:Frequency:Amplitude
Test Results
Detector = MAX PEAK
Sweep Count = 0
RF Atten (dB) = 20
Trace Mode = VIEW
M1 : 2480.026 MHz : -12.996 dBm
Limit: ≤ 8.0 dBm
Margin: -21.0 dB
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
57 of 62
A.4. Radiated Emissions
A.4.1. TX Spurious & Restricted Band Emissions
TX SPURIOUS & RESTRICTED BAND EMISSIONS
Variant: GFSK, Test Freq: 2402.00 MHz, Antenna: Aruba Metal sheet, Power Setting: 4, Duty Cycle (%): 99
1000.00 - 18000.00 MHz
Num
Frequency
MHz
Raw
dBμV
7205.55
48.49
Cable
Loss
dB
4.26
AF
dB
-7.35
Level Measurement
dBμV/m
Type
45.40
Peak (NRB)
Pol
Hgt
cm
Azt
Deg
Vertical
101
Limit
Margin
dBμV/m
dB
--
--
Pass
/Fail
Pass
Test Notes: EUT on 150 cm table powered by host laptop via CC debugger.
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
58 of 62
TX SPURIOUS & RESTRICTED BAND EMISSIONS
Variant: GFSK, Test Freq: 2440.00 MHz, Antenna: Aruba Metal sheet, Power Setting: 4, Duty Cycle (%): 99
1000.00 - 18000.00 MHz
Num
Frequency
MHz
Raw
dBμV
7319.24
55.14
Cable
Loss
dB
4.26
7319.24
44.75
4.26
AF
dB
Level Measurement
dBμV/m
Type
-7.27
52.13
-7.27
41.74
Pol
Hgt
cm
Azt
Deg
Limit
Margin
dBμV/m
dB
Pass
/Fail
Max Peak
Horizontal
134
74.0
-21.9
Pass
Max Avg
Horizontal
134
54.0
-12.3
Pass
Test Notes: EUT on 150 cm table powered by host laptop via CC debugger.
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
59 of 62
TX SPURIOUS & RESTRICTED BAND EMISSIONS
Variant: GFSK, Test Freq: 2480.00 MHz, Antenna: Aruba Metal sheet, Power Setting: 4, Duty Cycle (%): 99
1000.00 - 18000.00 MHz
Num
Frequency
MHz
Raw
dBμV
7439.43
52.57
Cable
Loss
dB
4.31
7439.43
42.04
4.31
AF
dB
Level Measurement
dBμV/m
Type
-7.13
49.75
-7.13
39.22
Pol
Hgt
cm
Azt
Deg
Limit
Margin
dBμV/m
dB
Pass
/Fail
Max Peak
Vertical
138
340
74.0
-24.3
Pass
Max Avg
Vertical
138
340
54.0
-14.8
Pass
Test Notes: EUT on 150 cm table powered by host laptop via CC debugger.
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
60 of 62
A.4.2. Restricted Edge & Band-Edge Emissions
RADIATED - LOWER RESTRICTED BAND-EDGE EMISSIONS
Variant: GFSK, Test Freq: 2402.00 MHz, Antenna: Aruba Metal sheet, Power Setting: 4, Duty Cycle (%): 99
2310.00 - 2410.00 MHz
Num
Frequency
MHz
Raw
dBμV
2382.16
26.24
Cable
Loss
dB
2.69
31.97
60.90
2390.00
11.43
2.69
32.04
46.16
2390.00
--
--
--
--
AF
dB
Level Measurement
dBμV/m
Type
Pol
Hgt
cm
Azt
Deg
Limit
Margin
dBμV/m
dB
Pass
/Fail
Max Peak
Vertical
156
30
74.0
-13.1
Pass
Max Avg
RestrictedBand
Vertical
156
30
54.0
-7.8
Pass
--
--
--
--
--
--
Test Notes: EUT on 150 cm table powered by host laptop via CC debugger.
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
Title:
To:
Serial #:
Issue Date:
Page:
Hewlett Packard Enterprise APINH303
FCC CFR 47 Part 15.247 (DTS) & IC RSS-247
HWPD85-U2 Rev A Bluetooth BLE
1st December 2016
61 of 62
RADIATED - UPPER RESTRICTED BAND-EDGE EMISSIONS
Variant: GFSK, Test Freq: 2480.00 MHz, Antenna: Aruba Metal sheet, Power Setting: 4, Duty Cycle (%): 99
2472.00 - 2500.00 MHz
Num
Frequency
MHz
Raw
dBμV
2483.50
13.72
Cable
Loss
dB
2.73
32.37
48.82
2483.50
26.25
2.73
32.37
61.35
2483.50
--
--
--
--
AF
dB
Level Measurement
dBμV/m
Type
Pol
Hgt
cm
Azt
Deg
Limit
Margin
dBμV/m
dB
Pass
/Fail
Max Avg
Vertical
151
47
54.0
-5.2
Pass
Max Peak
RestrictedBand
Vertical
151
47
74.0
-12.7
Pass
--
--
--
--
--
--
Test Notes: EUT on 150 cm table powered by host laptop via CC debugger.
back to matrix
This test report may be reproduced in full only. The document may only be updated by MiCOM Labs
personnel. All changes will be noted in the Document History section of the report.
MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com
575 Boulder Court
Pleasanton, California 94566, USA
Tel: +1 (925) 462 0304
Fax: +1 (925) 462 0306
www.micomlabs.com
Download: APINH303 802.11a/b/g/n/ac Wireless Access Point Test Report ©2016 MiCOM Labs Inc. Aruba Networks, Inc.
Mirror Download [FCC.gov]APINH303 802.11a/b/g/n/ac Wireless Access Point Test Report ©2016 MiCOM Labs Inc. Aruba Networks, Inc.
Document ID3252259
Application IDYVbkyI2YunbN+ZAXqgXMxQ==
Document DescriptionBLE Test Report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize132.95kB (1661864 bits)
Date Submitted2017-01-09 00:00:00
Date Available2017-01-11 00:00:00
Creation Date2017-12-20 13:46:07
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-12-20 13:46:07
Document Title©2016 MiCOM Labs Inc.
Document CreatorMicrosoft® Word 2010
Document Author: ©2016 MiCOM Labs Inc. • 575 Boulder Court • Pleasanton • CA 94566 • USA • Tel: +1 (925) 462-0304

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:828195f7-a29d-11f2-0000-02c7314339d4
Producer                        : GPL Ghostscript 9.18
Modify Date                     : 2017:07:16 23:46:17Z
Create Date                     : 2017:07:16 23:46:17Z
Creator Tool                    : UnknownApplication
Document ID                     : uuid:828195f7-a29d-11f2-0000-02c7314339d4
Format                          : application/pdf
Title                           : Untitled
EXIF Metadata provided by EXIF.tools

Facebook Twitter Google+ RSS © FCCID.io 2018