T103WIFI3GT Terminal Test Report 1 XAC Automation Corporation

XAC Automation Corporation Terminal

FCC ID Filing: MQT-T103WIFI3GT
Purchase on Amazon: Terminal

Trouble Viewing? See the or view the HTML Version or PDF in frame
Page 1 of T103WIFI3GT Terminal Test Report 1 XAC Automation Corporation

FCC Test Report
Report No.: RF131029E03H-1
FCC ID: MQT-T103WIFI3GT
Test Model: xAPT-103WiFi.3G
Series Model: xCE_T103WiFi.3G
Received Date: Dec. 14, 2012
Test Date: Jan. 08, 2013; Nov. 16 to 23, 2016
Issued Date: Dec. 07, 2016
Applicant: XAC AUTOMATION CORP.
Address: 4F, No. 30, INDUSTRY E. RD. IX, SCIENCE-BASED INDUSTRIAL
PARK,HSINCHU,TAIWAN
Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch
Hsin Chu Laboratory
Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300,
Taiwan R.O.C.
Test Location (1): E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300,
Taiwan R.O.C.
Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin
Chu Hsien 307, Taiwan R.O.C.
This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted
only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this
report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product
unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you
provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided,
however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time
shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific
mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report
must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 1 / 33
Report Format Version: 6.1.1
Table of Contents
Release Control Record .................................................................................................................................. 3
Certificate of Conformity ...................................................................................................................... 4
Summary of Test Results ..................................................................................................................... 5
2.1
2.2
Measurement Uncertainty ................................................................................................................... 5
Modification Record ............................................................................................................................ 5
General Information .............................................................................................................................. 6
3.1
3.2
3.2.1
3.3
3.3.1
3.4
Test Types and Results ...................................................................................................................... 15
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.1.6
4.1.7
4.2
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
4.2.7
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
4.3.7
4.4
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
4.4.6
4.4.7
General Description of EUT ................................................................................................................ 6
Description of Test Modes ................................................................................................................... 8
Test Mode Applicability and Tested Channel Detail ............................................................................. 9
Description of Support Units .............................................................................................................. 11
Configuration of System under Test .................................................................................................. 12
General Description of Applied Standards ........................................................................................ 14
Radiated Emission Measurement ..................................................................................................... 15
Limits of Radiated Emission Measurement ....................................................................................... 15
Test Instruments ................................................................................................................................ 16
Test Procedures ................................................................................................................................. 17
Deviation from Test Standard ............................................................................................................ 17
Test Setup .......................................................................................................................................... 18
EUT Operating Conditions................................................................................................................. 18
Test Results ....................................................................................................................................... 19
Conducted Emission Measurement .................................................................................................. 23
Limits of Conducted Emission Measurement .................................................................................... 23
Test Instruments ................................................................................................................................ 23
Test Procedures ................................................................................................................................. 24
Deviation from Test Standard ............................................................................................................ 24
TEST SETUP..................................................................................................................................... 24
EUT Operating Conditions................................................................................................................. 24
Test Results ....................................................................................................................................... 25
Frequency Stability ............................................................................................................................ 27
Limits of Frequency Stability Measurement ...................................................................................... 27
Test Setup .......................................................................................................................................... 27
Test Instruments ................................................................................................................................ 27
Test Procedure .................................................................................................................................. 28
Deviation fromTest Standard ............................................................................................................. 28
EUT Operating Conditions................................................................................................................. 28
Test Result ......................................................................................................................................... 29
20dB bandwidth................................................................................................................................. 30
Limits Of 20dB bandwidth Measurement .......................................................................................... 30
Test Setup .......................................................................................................................................... 30
Test Instruments ................................................................................................................................ 30
Test Procedures ................................................................................................................................. 30
Deviation from Test Standard ............................................................................................................ 30
EUT Operating Conditions................................................................................................................. 30
Test Results ....................................................................................................................................... 31
Pictures of Test Arrangements .......................................................................................................... 32
Appendix – Information on the Testing Laboratories ................................................................................ 33
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 2 / 33
Report Format Version: 6.1.1
Release Control Record
Issue No.
Description
Date Issued
RF131029E03H-1
Original release.
Dec. 07, 2016
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 3 / 33
Report Format Version: 6.1.1
1
Certificate of Conformity
Product: Terminal
Brand: XAC
Test Model: xAPT-103WiFi.3G
Series Model: xCE_T103WiFi.3G
Sample Status: MASS-PRODUCTION
Applicant: XAC AUTOMATION CORP.
Test Date: Jan. 08, 2013; Nov. 16 to 23, 2016
Standards: 47 CFR FCC Part 15, Subpart C (Section 15.225)
47 CFR FCC Part 15, Subpart C (Section 15.215)
ANSI C63.10:2013
The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd.,
Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data
evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts
of the measurements of the sample’s EMC characteristics under the conditions specified in this report.
Prepared by :
Date:
Dec. 07, 2016
Date:
Dec. 07, 2016
Wendy Wu / Specialist
Approved by :
May Chen / Manager
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 4 / 33
Report Format Version: 6.1.1
2
Summary of Test Results
47 CFR FCC Part 15, Subpart C (SECTION 15.225, 15.215)
FCC
Test Item
Clause
15.207
Conducted emission test
15.225 (a)
15.225 (b)
15.225 (c)
15.225 (d)
15.225 (e)
15.215 (c)
2.1
Result
The field strength of any emissions
within the band 13.553-13.567 MHz
The field strength of any emissions
within the bands 13.410-13.553
MHz and 13.567-13.710 MHz
The field strength of any emissions
within the bands 13.110-13.410
MHz and 13.710-14.010 MHz
The field strength of any emissions
appearing outside of the
13.110-14.010 MHz band
The frequency tolerance
20dB Bandwidth
Remarks
PASS
Meet the requirement of limit.
Minimum passing margin is -16.50dB
at 0.15781MHz.
PASS
Meet the requirement of limit.
PASS
Meet the requirement of limit.
PASS
Meet the requirement of limit.
PASS
PASS
PASS
Meet the requirement of limit.
Minimum passing margin is -0.2dB at
426.68MHz.
Meet the requirement of limit.
Meet the requirement of limit.
Measurement Uncertainty
Where relevant, the following measurement uncertainty levels have been estimated for tests performed on
the EUT as specified in CISPR 16-4-2:
Measurement
Frequency
Conducted Emissions at mains ports
150kHz ~ 30MHz
30MHz ~ 1GHz
1GHz ~ 6GHz
6GHz ~ 18GHz
18GHz ~ 40GHz
Radiated Emissions up to 1 GHz
Radiated Emissions above 1 GHz
2.2
Expanded Uncertainty
(k=2) (±)
1.83 dB
3.47 dB
3.65 dB
3.88 dB
4.11 dB
Modification Record
There were no modifications required for compliance.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 5 / 33
Report Format Version: 6.1.1
3
General Information
3.1
General Description of EUT
Product
Terminal
Brand
XAC
Test Model
xAPT-103WiFi.3G
Series Model
xCE_T103WiFi.3G
Status of EUT
MASS-PRODUCTION
Power Supply Rating
DC 12V from power adapter
Modulation Type
ASK
Operating Frequency
13.56MHz
Number of Channel
Antenna Type
Refer to Note
Antenna Connector
Refer to Note
Accessory Device
Adapter (Optional) x 1
Data Cable Supplied
NA
Note:
1. All models are listed as below.
Brand
Model
XAC
xAPT-103WiFi.3G
xCE_T103WiFi.3G
Difference
For marketing requirement
From the above models, model: xAPT-103WiFi.3G was selected as representative model for the test and its
data was recorded in this report.
2. The EUT is a WLAN, RFID, GSM and WCDMA device.
3. WLAN, RFID, GSM and WCDMA technology cannot transmit at same time.
4. The EUT power needs to be supplied from one power adapter, the information is as below table:
Brand:
DELTA
Model No.:
ADP-36PH B
AC100-240V, 1A, 50-60Hz
Input power :
AC input cable (Unshielded, 1.75m)
DC 12V, 3A
Output power :
DC output cable (Unshielded, 0.9 m with one core)
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 6 / 33
Report Format Version: 6.1.1
5. The antennas provided to the EUT, please refer to the following table:
RFID Antenna Spec.
Brand
Model No.
XAC
PCB ENIG ANT BOARD
(W/KEY) 8006(ROHS)
Antenna Antenna
Type
Connector
Loop
NA
Antenna
Gain(dBi)
Frequency
(MHz)
13
13.56
Gain(dBi)
Frequency
(MHz)
0.14
850
2.57
1900
GPRS / WCDMA(UMTS) / HSDPA / EDGE Antenna Spec.
Antenna Antenna
Type
Connector
Brand
Model No.
Ethertronics Inc.
T-000084-01
FPCB
NA
WLAN Antenna Spec.
Brand
Model No.
Antenna Type
Antenna
Connector
Antenna Gain(dBi)

Frequency
(MHz)
ACX
AT3216-T2R4
PAA
Chip
NA
1.5
2400-2500
6. The above EUT information is declared by manufacturer and for more detailed features description,
please refer to the manufacturer's specifications or user's manual.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 7 / 33
Report Format Version: 6.1.1
3.2
Description of Test Modes
One channel was provided to this EUT:
Channel
FREQ. (MHz)
13.56
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 8 / 33
Report Format Version: 6.1.1
3.2.1
Test Mode Applicability and Tested Channel Detail
APPLICABLE TO
EUT CONFIGURE
MODE
DESCRIPTION
Where
RE
PLC
FS
√
√
√
EB
√
RE: Radiated Emission
PLC: Power Line Conducted
Emission
FS: Frequency Stability
EB: 20dB Bandwidth measurement
RADIATED EMISSION TEST:
Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
between available modulations, data rates and antenna ports (if EUT with antenna diversity
architecture).
Following channel(s) was (were) selected for the final test as listed below.
AVAILABLE CHANNEL
TESTED CHANNEL
MODULATION TYPE
ASK
POWER LINE CONDUCTED EMISSION TEST:
Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
between available modulations, data rates and antenna ports (if EUT with antenna diversity
architecture).
Following channel(s) was (were) selected for the final test as listed below.
AVAILABLE CHANNEL
TESTED CHANNEL
MODULATION TYPE
ASK
FREQUENCY STABILITY:
Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
between available modulations, data rates and antenna ports (if EUT with antenna diversity
architecture).
Following channel(s) was (were) selected for the final test as listed below.
AVAILABLE CHANNEL
TESTED CHANNEL
MODULATION TYPE
ASK
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 9 / 33
Report Format Version: 6.1.1
20dB BANDWIDTH:
This item includes all test value of each mode, but only includes spectrum plot of worst value of each
mode.
Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
between available modulations, data rates and antenna ports (if EUT with antenna diversity
architecture).
Following channel(s) was (were) selected for the final test as listed below.
AVAILABLE CHANNEL
TESTED CHANNEL
MODULATION TYPE
ASK
TEST CONDITION:
Applicable To
RE
PLC
Environmental Conditions
23deg. C, 72%RH
25deg. C, 67%RH
Input Power
120Vac, 60Hz
Tested By
Andy Ho
Weiwie Lo
24deg. C, 71%RH
120Vac, 60Hz
Andy Ho
FS
25deg. C, 60%RH
120Vac, 60Hz
Rex Huang
EB
25deg. C, 60%RH
120Vac, 60Hz
Rex Huang
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 10 / 33
Report Format Version: 6.1.1
3.3
Description of Support Units
The EUT has been tested as an independent unit together with other necessary accessories or support units.
The following support units or accessories were used to form a representative test configuration during the
tests.
No.
Product
Adapter
Brand
Model No.
ADP-36PH B
MC749TA/A
Serial No.
NA
FCC ID
NA
Remark
Supplied by Client
iPod shuffle
DELTA
Apple
CC4DN25WDFDM
NA
Provided by Lab
iPod shuffle
Apple
MD778TA/A
CC4JMA9KF4T1
NA
Provided by Lab
Laptop
DELL
E6420
482T3R1
FCC DoC
Provided by Lab
Telephone
WONDER
WD-303
NA
Provided by Lab
Micro SD Card
SanDisk
2G
NA
Provided by Lab
7C17KA
05211
NA
Note:
All power cords of the above support units are non-shielded (1.8m).
ID
Descriptions
Qty.
DC Cable
0.9
Shielding
(Yes/No)
No
AC Cable
1.75
No
USB Cable
0.1
USB Cable
RJ-45 Cable
Length (m)
Cores (Qty.)
Remarks
Supplied by client
Supplied by client
Yes
Provided by Lab
0.1
Yes
Provided by Lab
10
No
Provided by Lab
RJ-11 Cable
10
No
Provided by Lab
Console Cable
1.5
No
Supplied by client
Note: The core(s) is(are) originally attached to the cable(s).
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 11 / 33
Report Format Version: 6.1.1
3.3.1
Configuration of System under Test
For conducted emission test
Note: Micro USB port for F/W update.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 12 / 33
Report Format Version: 6.1.1
For radiated emission test
Note: Micro USB port for F/W update.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 13 / 33
Report Format Version: 6.1.1
3.4
General Description of Applied Standards
The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the
requirements of the following standards:
FCC Part 15, Subpart C (15.225)
FCC Part 15, Subpart C (15.215)
ANSI C63.10-2013
All test items have been performed and recorded as per the above standards.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 14 / 33
Report Format Version: 6.1.1
4
Test Types and Results
4.1
Radiated Emission Measurement
4.1.1
Limits of Radiated Emission Measurement
(a) The field strength of any emissions within the band 13.553-13.567 MHz shall not exceed 15,848
microvolts/meter at 30 meters.
(b) Within the bands 13.410-13.553 MHz and 13.567-13.710 MHz, the field strength of any emissions shall
not exceed 334 microvolts/meter at 30 meters.
(c) Within the bands 13.110-13.410 MHz and 13.710-14.010 MHz the field strength of any emissions shall
not exceed 106 microvolts/meter at 30 meters.
(d) The field strength of any emissions appearing outside of the 13.110-14.010 MHz band shall not
exceed the general radiated emission limits in §15.209 as below table:
Frequencies
(MHz)
Field Strength
(microvolts/meter)
Measurement Distance
(meters)
0.009 ~ 0.490
2400/F(kHz)
300
0.490 ~ 1.705
24000/F(kHz)
30
1.705 ~ 30.0
30
30
30 ~ 88
100
88 ~ 216
150
216 ~ 960
200
Above 960
500
NOTE:
1.
The lower limit shall apply at the transition frequencies.
2.
Emission level (dBuV/m) = 20 log Emission level (uV/m).
3.
For frequencies above 1000MHz, the field strength limits are based on average detector, however, the
peak field strength of any emission shall not exceed the maximum permitted average limits, specified
above by more than 20dB under any condition of modulation.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 15 / 33
Report Format Version: 6.1.1
4.1.2 Test Instruments
DESCRIPTION &
MANUFACTURER
Test Receiver
Agilent
(*)
Pre-Amplifier
EMCI
(*)
Loop Antenna
Electro-Metrics
RF Cable
Pre-Amplifier
Mini-Circuits
Trilog Broadband Antenna
SCHWARZBECK
RF Cable
Fixed attenuator
Mini-Circuits
Software
Antenna Tower & Turn Table
Max-Full
CALIBRATED
CALIBRATED
DATE
UNTIL
MY50010156
Aug. 18, 2016
Aug. 17, 2017
EMC001340
980142
Jan. 20, 2016
Jan. 19, 2018
EM-6879
264
Dec. 16, 2014
Dec. 15, 2016
NA
LOOPCAB-001
LOOPCAB-002
Jan. 18, 2016
Jan. 17, 2017
ZFL-1000VH2B
AMP-ZFL-05
May 07, 2016
May 06, 2017
VULB 9168
9168-156
Jan. 04, 2016
Jan. 03, 2017
8D
966-3-1
966-3-2
966-3-3
Apr. 02, 2016
Apr. 01, 2017
UNAT-5+
PAD-3m-3-01
Oct. 05, 2016
Oct. 04, 2017
ADT_Radiated_V8.7.08 NA
NA
NA
MF-7802
NA
NA
MODEL NO.
SERIAL NO.
N9038A
MF780208406
Note:
1. The calibration interval of the above test instruments is 12 months and the calibrations are
traceable to NML/ROC and NIST/USA.
2. *The calibration interval of the above test instruments is 24 months and the calibrations are
traceable to NML/ROC and NIST/USA.
3. The test was performed in 966 Chamber No. 3.
4. The FCC Site Registration No. is 147459
5 Loop antenna was used for all emissions below 30 MHz.
6. The CANADA Site Registration No. is 20331-1
7. Tested Date:Nov. 16 to 23, 2016
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 16 / 33
Report Format Version: 6.1.1
4.1.3 Test Procedures
For Radiated emission below 30MHz
a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber
room. The table was rotated 360 degrees to determine the position of the highest radiation.
b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top
of a variable-height antenna tower.
c. Both X and Y axes of the antenna are set to make the measurement.
d. For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned
from 0 degrees to 360 degrees to find the maximum reading.
e. The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with
Maximum Hold Mode.
NOTE:
1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9kHz at frequency
below 30MHz.
For Radiated emission above 30MHz
a. The EUT was placed on the top of a rotating table 0.8 meters (for 30MHz ~ 1GHz) / 1.5 meters (for above
1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to
determine the position of the highest radiation.
b.
The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top
of a variable-height antenna tower.
c.
The height of antenna is varied from one meter to four meters above the ground to determine the
maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to
make the measurement.
d.
For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned
to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to
find the maximum reading.
e.
The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum
hold mode when the test frequency is below 1 GHz.
f.
The test-receiver system was set to peak and average detect function and specified bandwidth with
maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets
average limit, measurement with the average detector is unnecessary.
Note:
1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for
Quasi-peak detection (QP) at frequency below 1GHz.
2.
The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz
for Peak detection (PK) at frequency above 1GHz.
3.
The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is ≥ 1/T
(Duty cycle < 98%) or 10Hz (Duty cycle ≥ 98%) for Average detection (AV) at frequency above 1GHz.
4.
All modes of operation were investigated and the worst-case emissions are reported.
4.1.4
Deviation from Test Standard
No deviation.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 17 / 33
Report Format Version: 6.1.1
4.1.5
Test Setup
For Radiated emission below 30MHz
1m
EUT&
Support Units
3m
Turn Table
80cm
Ground Plane
Test Receiver
For Radiated emission 30MHz to 1GHz
Ant. Tower
1-4m
Variable
3m
10m
EUT&
Support Units
Turn Table
80cm
Ground Plane
Test Receiver
For the actual test configuration, please refer to the attached file (Test Setup Photo).
4.1.6
EUT Operating Conditions
a. Placed the EUT on the testing table.
b. Set the EUT under transmission condition continuously at specific channel frequency.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 18 / 33
Report Format Version: 6.1.1
4.1.7
Test Results
Frequency Range
13.110 ~ 14.010MHz
Detector Function
Quasi-Peak
Antenna Polarity & Test Distance: Loop Antenna Open At 3m
No.
Freq.
(MHz)
13.35
13.49
*13.56
13.63
13.77
Emission
Level
(dBuV/m)
55.5 QP
60.0 QP
81.9 QP
60.3 QP
58.1 QP
Limit
(dBuV/m)
Margin
(dB)
80.5
90.5
124.0
90.5
80.5
-25.0
-30.5
-42.1
-30.2
-22.4
Antenna
Height
(m)
1.00
1.00
1.00
1.00
1.00
Table
Angle
(Degree)
310
345
343
346
346
Raw
Value
(dBuV)
58.8
63.3
85.2
63.6
61.4
Correction
Factor
(dB/m)
-3.3
-3.3
-3.3
-3.3
-3.3
REMARKS:
1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB)
– Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission level – Limit value.
5. Above limits have been translated by the formula
6. " * ": Fundamental frequency.
The measured field strength was extrapolated to distance 30 meters, using the formula that the limit of field
strength varies as the inverse distance square (40dB per decade of distance)
Example:
13.56MHz = 15848uV/m
30m
= 84dBuV/m
30m
= 84+20log(30/3)
3m
= 124dBuV/m
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 19 / 33
Report Format Version: 6.1.1
Frequency Range
13.110 ~ 14.010MHz
Detector Function
Quasi-Peak
Antenna Polarity & Test Distance: Loop Antenna Close At 3m
No.
Freq.
(MHz)
13.35
13.49
*13.56
13.63
13.77
Emission
Level
(dBuV/m)
52.9 QP
56.9 QP
79.1 QP
57.2 QP
55.4 QP
Limit
(dBuV/m)
Margin
(dB)
80.5
90.5
124.0
90.5
80.5
-27.6
-33.6
-44.9
-33.3
-25.1
Antenna
Height
(m)
1.00
1.00
1.00
1.00
1.00
Table
Angle
(Degree)
217
195
240
192
169
Raw
Value
(dBuV)
56.2
60.2
82.4
60.5
58.7
Correction
Factor
(dB/m)
-3.3
-3.3
-3.3
-3.3
-3.3
REMARKS:
1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB)
– Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission level – Limit value.
5. Above limits have been translated by the formula
6. " * ": Fundamental frequency.
The measured field strength was extrapolated to distance 30 meters, using the formula that the limit of field
strength varies as the inverse distance square (40dB per decade of distance)
Example:
13.56MHz = 15848uV/m
30m
= 84dBuV/m
30m
= 84+20log(30/3)
3m
= 124dBuV/m
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 20 / 33
Report Format Version: 6.1.1
Frequency Range
Below 30MHz
Detector Function
Quasi-Peak
Antenna Polarity & Test Distance: Loop Antenna Open At 3m
NO.
FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1.01
3.07
17.24
20.66
21.13
28.24
39.7 QP
29.3 QP
34.3 QP
44.4 QP
48.3 QP
38.2 QP
67.5
69.5
69.5
69.5
69.5
69.5
-27.8
-40.2
-35.2
-25.1
-21.2
-31.3
1.00
1.00
1.00
1.00
1.00
1.00
190
102
132
224
360
340
38.9
32.1
38.2
48.8
52.6
40.9
0.8
-2.8
-3.9
-4.4
-4.3
-2.7
Antenna Polarity & Test Distance: Loop Antenna Close At 3m
NO.
FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
0.50
3.13
6.92
20.66
21.13
28.24
50.3 QP
36.7 QP
38.0 QP
51.2 QP
55.6 QP
44.2 QP
73.6
69.5
69.5
69.5
69.5
69.5
-23.3
-32.8
-31.5
-18.3
-13.9
-25.3
1.00
1.00
1.00
1.00
1.00
1.00
239
258
42
20
328
245
45.7
39.5
40.9
55.6
59.9
46.9
4.6
-2.8
-2.9
-4.4
-4.3
-2.7
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB)
– Pre-Amplifier Factor (dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 21 / 33
Report Format Version: 6.1.1
Frequency Range
30MHz ~ 1000MHz
Detector Function
Quasi-Peak
Antenna Polarity & Test Distance: Horizontal At 3 M
NO.
FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
108.04
156.00
252.01
266.68
373.33
533.36
37.6 QP
39.9 QP
44.7 QP
45.3 QP
41.8 QP
38.9 QP
43.5
43.5
46.0
46.0
46.0
46.0
-5.9
-3.6
-1.3
-0.7
-4.2
-7.1
2.00 H
2.00 H
1.00 H
1.00 H
1.00 H
1.50 H
300
84
312
302
61
41
49.3
48.2
54.1
53.9
47.3
40.8
-11.7
-8.3
-9.4
-8.6
-5.5
-1.9
Antenna Polarity & Test Distance: Vertical At 3 M
NO.
FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
60.00
180.01
252.00
346.68
426.68
533.33
39.0 QP
38.6 QP
44.8 QP
41.6 QP
45.8 QP
40.3 QP
40.0
43.5
46.0
46.0
46.0
46.0
-1.0
-4.9
-1.2
-4.4
-0.2
-5.7
1.00 V
1.00 V
1.50 V
1.50 V
1.50 V
1.00 V
132
201
354
115
73
180
47.7
48.1
54.2
48.0
49.8
42.2
-8.7
-9.5
-9.4
-6.4
-4.0
-1.9
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 22 / 33
Report Format Version: 6.1.1
4.2
Conducted Emission Measurement
4.2.1
Limits of Conducted Emission Measurement
Conducted Limit (dBuV)
Frequency (MHz)
Quasi-peak
Average
0.15 - 0.5
66 - 56
56 - 46
0.50 - 5.0
56
46
5.0 - 30.0
60
50
Note: 1. The lower limit shall apply at the transition frequencies.
2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz.
4.2.2
Test Instruments
DESCRIPTION &
MANUFACTURER
Test Receiver
R&S
Line-Impedance
Stabilization Network
(for EUT)
R&S
Line-Impedance
Stabilization Network
(for Peripheral)
R&S
RF Cable
10 dB PAD
Mini-Circuits
Software
BVADT
MODEL NO.
SERIAL NO.
CALIBRATED
CALIBRATED
DATE
UNTIL
ESCS 30
847124/029
Oct. 24, 2016
Oct. 23, 2017
ESH3-Z5
848773/004
Oct. 26, 2016
Oct. 25, 2017
ENV216
100072
June 13, 2016
June 12, 2017
5D-FB
COCCAB-001
Sep. 30, 2016
Sep. 29, 2017
HAT-10+
CONATT-004
June 20, 2016
June 19, 2017
BVADT_Cond_
V7.3.7.4
NA
NA
NA
Note:
1. The calibration interval of the above test instruments are 12 months and the calibrations are
traceable to NML/ROC and NIST/USA.
2. The test was performed in Shielded Room No. 1.
3 Tested Date:Nov. 24, 2016
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 23 / 33
Report Format Version: 6.1.1
4.2.3
Test Procedures
a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being
connected to the power mains through a line impedance stabilization network (LISN). Other support
units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH
of coupling impedance for the measuring instrument.
b. Both lines of the power mains connected to the EUT were checked for maximum conducted
interference.
c.
The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was
not recorded.
NOTE: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP)
and average detection (AV) at frequency 0.15MHz-30MHz.
4.2.4
Deviation from Test Standard
No deviation.
4.2.5
TEST SETUP
Vertical Ground
Reference Plane
40cm
Test Receiver
EUT
80cm
LISN
Horizontal Ground
Reference Plane
Note: 1.Support units were connected to second LISN.
For the actual test configuration, please refer to the attached file (Test Setup Photo).
4.2.6
EUT Operating Conditions
Same as 4.1.6.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 24 / 33
Report Format Version: 6.1.1
4.2.7
Test Results
Phase
No
Detector Function
Line (L)
Freq.
[MHz]
0.15000
0.19297
0.32578
0.38828
0.94688
28.00391
Corr.
Factor
(dB)
10.19
10.19
10.21
10.22
10.26
11.45
Reading Value
[dB (uV)]
Q.P.
AV.
38.69
22.01
32.87
16.81
17.76
7.37
15.21
8.22
0.55
-5.54
11.62
9.01
Emission Level
[dB (uV)]
Q.P.
AV.
48.88
32.20
43.06
27.00
27.97
17.58
25.43
18.44
10.81
4.72
23.07
20.46
Quasi-Peak (QP) /
Average (AV)
Limit
[dB (uV)]
Q.P.
AV.
66.00
56.00
63.91
53.91
59.56
49.56
58.10
48.10
56.00
46.00
60.00
50.00
Margin
(dB)
Q.P.
AV.
-17.12
-23.80
-20.85
-26.91
-31.59
-31.98
-32.67
-29.66
-45.19
-41.28
-36.93
-29.54
REMARKS:
1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
2. The emission levels of other frequencies were very low against the limit.
3. Margin value = Emission level - Limit value
4. Correction factor = Insertion loss + Cable loss
5. Emission Level = Correction Factor + Reading Value.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 25 / 33
Report Format Version: 6.1.1
Phase
No
Detector Function
Neutral (N)
Freq.
[MHz]
0.15781
0.18125
0.20859
0.38438
5.55078
28.00000
Corr.
Factor
(dB)
10.18
10.17
10.16
10.21
10.25
11.06
Reading Value
[dB (uV)]
Q.P.
AV.
38.90
23.51
35.03
19.39
29.41
14.49
19.96
11.26
10.16
6.19
14.47
10.90
Emission Level
[dB (uV)]
Q.P.
AV.
49.08
33.69
45.20
29.56
39.57
24.65
30.17
21.47
20.41
16.44
25.53
21.96
Quasi-Peak (QP) /
Average (AV)
Limit
[dB (uV)]
Q.P.
AV.
65.58
55.58
64.43
54.43
63.26
53.26
58.18
48.18
60.00
50.00
60.00
50.00
Margin
(dB)
Q.P.
AV.
-16.50
-21.89
-19.23
-24.87
-23.69
-28.61
-28.01
-26.71
-39.59
-33.56
-34.47
-28.04
REMARKS:
1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
2. The emission levels of other frequencies were very low against the limit.
3. Margin value = Emission level - Limit value
4. Correction factor = Insertion loss + Cable loss
5. Emission Level = Correction Factor + Reading Value.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 26 / 33
Report Format Version: 6.1.1
4.3
Frequency Stability
4.3.1
Limits of Frequency Stability Measurement
The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating frequency
over a temperature variation of –20 degrees to 50 degrees C at normal supply voltage, and for a variation in
the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees C.
4.3.2
Test Setup
Temperature
Chamber
Spectrum Analyzer
AC Power Supply
4.3.3
Test Instruments
DESCRIPTION &
CALIBRATED
CALIBRATED
DATE
UNTIL
100964
June 28, 2016
June 27, 2017
1440452
NA
NA
GTH-150-40-SP
MAA0812-008
-AR
Jan. 15, 2016
Jan. 14, 2017
87III
Nov. 10, 2016
Nov. 09, 2017
MODEL NO.
SERIAL NO.
Spectrum Analyzer
R&S
FSV40
AC Power Source
Extech Electronics
6205
Temperature &
Humidity Chamber
Giant Force
Digital Multimeter
FLUKE
MANUFACTURER
73680266
Note:
1. The calibration interval of the above test instruments is 12 months and the calibrations are
traceable to NML/ROC and NIST/USA.
2. Tested date : Nov. 16, 2016
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 27 / 33
Report Format Version: 6.1.1
4.3.4
Test Procedure
a. The EUT was placed inside the environmental test chamber and powered by nominal AC voltage.
b. Turned the EUT on and coupled its output to a spectrum analyzer.
c. Turned the EUT off and set the chamber to the highest temperature specified.
d. Allowed sufficient time (approximately 30 min) for the temperature of the chamber to stabilize then turned
the EUT on and measured the operating frequency after 2, 5, and 10 minutes.
e. Repeated step 2 and 3 with the temperature chamber set to the lowest temperature.
f. The test chamber was allowed to stabilize at +20 degree C for a minimum of 30 minutes. The supply
voltage was then adjusted on the EUT from 85% to 115% and the frequency record.
4.3.5
Deviation fromTest Standard
No deviation.
4.3.6
EUT Operating Conditions
Same as Item 4.1.6.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 28 / 33
Report Format Version: 6.1.1
4.3.7
Test Result
Frequency Stability Versus Temp.
0 Minute
2 Minute
5 Minute
10 Minute
Power
TEMP.
Measured Frequency Measured Frequency Measured Frequency Measured Frequency
Supply
(℃)
Frequency
Drift
Frequency
Drift
Frequency
Drift
Frequency
Drift
(Vac)
(MHz)
(MHz)
(MHz)
(MHz)
50
120
13.56004
0.00029
13.56005
0.00037
13.56005
0.00037
13.56006
0.00044
40
120
13.55998
-0.00015
13.55997
-0.00022
13.55997
-0.00022
13.55997
-0.00022
30
120
13.56001
0.00007
13.56002
0.00015
13.56001
0.00007
13.56001
0.00007
20
120
13.55996
-0.00029
13.55997
-0.00022
13.55997
-0.00022
13.55997
-0.00022
10
120
13.55999
-0.00007
13.55999
-0.00007
13.56
0.00000
13.55999
-0.00007
120
13.55992
-0.00059
13.55993
-0.00052
13.55993
-0.00052
13.55993
-0.00052
-10
120
13.56007
0.00052
13.56007
0.00052
13.56007
0.00052
13.56007
0.00052
-20
120
13.56005
0.00037
13.56005
0.00037
13.56004
0.00029
13.56004
0.00029
-30
120
13.56003
0.00022
13.56003
0.00022
13.56003
0.00022
13.56003
0.00022
Frequency Stability Versus Voltage
0 Minute
2 Minute
5 Minute
10 Minute
Power
TEMP.
Measured Frequency Measured Frequency Measured Frequency Measured Frequency
Supply
(℃)
Frequency
Drift
Frequency
Drift
Frequency
Drift
Frequency
Drift
(Vac)
20
(MHz)
(MHz)
(MHz)
(MHz)
138
13.55996
-0.00029
13.55997
-0.00022
13.55997
-0.00022
13.55997
-0.00022
120
13.55996
-0.00029
13.55997
-0.00022
13.55997
-0.00022
13.55997
-0.00022
102
13.55996
-0.00029
13.55997
-0.00022
13.55997
-0.00022
13.55997
-0.00022
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 29 / 33
Report Format Version: 6.1.1
4.4
20dB bandwidth
4.4.1
Limits Of 20dB BANDWIDTH Measurement
The 20dB bandwidth shall be specified in operating frequency band.
4.4.2
Test Setup
EUT
4.4.3
Spectrum
Analyzer
Attenuator
Test Instruments
DESCRIPTION &
MANUFACTURER
R&S SPECTRUM
ANALYZER
MODEL NO.
SERIAL NO.
FSP40
100060
CALIBRATED
CALIBRATED
DATE
UNTIL
May 09, 2012
May 10, 2013
Note:
1. The calibration interval of the above test instruments is 12 months and the calibrations are
traceable to NML/ROC and NIST/USA.
2. Tested date : Jan. 08, 2013
4.4.4
Test Procedures
The bandwidth of the fundamental frequency was measured by spectrum analyzer with 1kHz RBW and
3kHz VBW. The 20dB bandwidth is defined as the total spectrum the power of which is higher than peak
power minus 20dB.
4.4.5
Deviation from Test Standard
No deviation.
4.4.6
EUT Operating Conditions
Same as Item 4.1.6.
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 30 / 33
Report Format Version: 6.1.1
4.4.7
Test Results
20dBc point (Low)
20dBc point (High)
Operating frequency
band (MHz)
Pass/Fail
13.48 MHz
13.71 MHz
13.11 – 14.01
PASS
Spectrum Plot Of Value
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 31 / 33
Report Format Version: 6.1.1
5
Pictures of Test Arrangements
Please refer to the attached file (Test Setup Photo).
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 32 / 33
Report Format Version: 6.1.1
Appendix – Information on the Testing Laboratories
We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to
provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and
approved according to ISO/IEC 17025.
If you have any comments, please feel free to contact us at the following:
Linko EMC/RF Lab
Hsin Chu EMC/RF/Telecom Lab
Tel: 886-2-26052180
Tel: 886-3-6668565
Fax: 886-2-26051924
Fax: 886-3-6668323
Hwa Ya EMC/RF/Safety Lab
Tel: 886-3-3183232
Fax: 886-3-3270892
Email: service.adt@tw.bureauveritas.com
Web Site: www.bureauveritas-adt.com
The address and road map of all our labs can be found in our web site also.
--- END ---
Report No.: RF131029E03H-1
Reference No.: 161109E05
Page No. 33 / 33
Report Format Version: 6.1.1
Download: T103WIFI3GT Terminal Test Report 1 XAC Automation Corporation
Mirror Download [FCC.gov]T103WIFI3GT Terminal Test Report 1 XAC Automation Corporation
Document ID3253451
Application ID9w7iRki9lBdqj5foBywiQQ==
Document DescriptionTest Report (RFID) rev 2.pdf
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize57.39kB (717426 bits)
Date Submitted2017-01-10 00:00:00
Date Available2017-01-11 00:00:00
Creation Date2017-12-20 15:57:25
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-12-20 15:57:25
Document TitleTest Report 1
Document CreatorMicrosoft® Office Word 2007
Document Author: Jim

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:f6fe099f-a288-11f2-0000-02c7314339d4
Producer                        : GPL Ghostscript 9.18
Modify Date                     : 2017:07:16 21:19:13Z
Create Date                     : 2017:07:16 21:19:13Z
Creator Tool                    : UnknownApplication
Document ID                     : uuid:f6fe099f-a288-11f2-0000-02c7314339d4
Format                          : application/pdf
Title                           : Untitled
EXIF Metadata provided by EXIF.tools

Facebook Twitter Google+ RSS © FCCID.io 2018