TC700K Touch computer RF Exposure Info RF Exposure Appendix A-2 Zebra Technologies Corporation

Zebra Technologies Corporation Touch computer

FCC ID Filing: UZ7TC700K
Purchase on Amazon: Touch computer

Trouble Viewing? See the or view the HTML Version or PDF in frame
Page 1 of TC700K Touch computer RF Exposure Info RF Exposure Appendix A-2 Zebra Technologies Corporation

FCC SAR Test Report
Appendix C.
Report No. : FA672834
DASY Calibration Certificate
The DASY calibration certificates are shown as follows.
SPORTON INTERNATIONAL INC.
TEL : 886-3-327-3456 / FAX : 886-3-328-4978
FCC ID : UZ7TC75EK
Page C1 of C1
Issued Date : Oct. 07, 2016
Form version. : 160427
Calibration Laboratory of
Schmid & Partner
Engineering AG
Schweizerischer Kalibrierdienst
Service suisse d'etalonnage
Zeughausstrasse 43, 8004 Zurich, Switzerland
Swiss Calibration Service
Accredited by the Swiss Accreditation Service (SAS)
Accreditation No.:
Servizio svizzero di taratura
SCS 0108
The Swiss Accreditation Service is one of the signatories to the EA
Multilateral Agreement for the recognition of calibration certificates
Client
Auden
Certificate No:
D2450V2-735_ Dec15
CALIBRATION CERTIFICATE
Object
D2450V2 - SN: 735
Calibration procedure(s)
QA CAL-05.v9
Calibration procedure for dipole validation kits above 700 MHz
Calibration date:
December 10, 2015
This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (SI).
The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate.
All calibrations have been conducted in the closed laboratory facility: en vironment temperatu re (22 ± 3)°C and humidity < 70%.
Calibration Equipment used (M&T E critical for calibration)
Primary Standards
ID #
Cal Date (Certificate No.)
Scheduled Calibration
Power meter EPM-442A
GB37480704
07-0ct-15 (No. 217-02222)
Oct-1 6
Power sensor HP 8481A
US37292783
MY4 1092317
SN: 5058 (20k)
07-0ct-1 5 (No. 217-02222)
07-0ct-15 (No. 217-02223)
Oct-1 6
Power sensor HP 8481A
01-Apr-1 5 (No. 217 -02131)
Mar-16
Reference 20 dB Attenuator
Oct-16
Type-N mismatch combination
SN: 5047.2 I 06327
01-Apr-1 5 (No. 217-02134)
Mar-16
Reference Probe EX3DV4
DAE4
SN: 7349
30-Dec-14 (No. EX3-7349_Dec 14)
17-Aug-15 (No. DAE4-601_Aug15)
Dec-15
Scheduled Check
SN: 601
Aug-16
Secondary Standards
ID#
Check Date (in house)
RF generator R&S SMT-06
100972
15-Jun-1 5 (in house check Jun-15)
In house check: Jun-18
Network Analyzer HP 8753E
US37390585 S4206
18-0ct-01 (in house check Oct-15)
In house check: Oct-16
Name
Function
Calibrated by:
lsrae Elnaouq
Laboratory Technician
Approved by:
Katja Pokovic
Technical Manager
Issued: December 10, 2015
This calibration certificate shall not be reproduced except in full without written approval of the laboratory.
C e rtificate No : D2450V2-735_ Dec1 5
Page 1 of 8
Calibration Laboratory of
Schmid & Partner
Engineering AG
Schweizerischer Kalibrierdienst
Service suisse d'etalonnage
Servizio svizzero di taratura
Zeughausstrasse 43, 8004 Zurich, Switzerland
Swiss Calibration Service
Accreditation No.:
Accredited by the Swiss Accreditation Service (SAS)
SCS 0108
The Swiss Accreditation Service is one of the signatories to the EA
Multilateral Agreement for the recognition of calibration certificates
Glossary:
TSL
ConvF
N/A
tissue simulating liquid
sensitivity in TSL / NORM x,y,z
not applicable or not measured
Calibration is Performed According to the Following Standards:
a) IEEE Std 1528-2013, "IEEE Recommended Practice for Determining the Peak SpatialAveraged Specific Absorption Rate (SAR) in the Human Head from Wireless
Communications Devices: Measurement Techniques", June 2013
b) IEC 62209-1 , "Procedure to measure the Specific Absorption Rate (SAR) for hand-held
devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)",
February 2005
c) IEC 62209-2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless
communication devices used in close proximity to the human body (frequency range of 30
MHz to 6 GHz)", March 2010
d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz"
Additional Documentation:
e) DASY4/5 System Handbook
Methods Applied and Interpretation of Parameters:
• Measurement Conditions: Further details are available from the Validation Report at the end
of the certificate. All figures stated in the certificate are valid at the frequency indicated.
• Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed
point exactly below the center marking of the flat phantom section, with the arms oriented
parallel to the body axis.
• Feed Point Impedance and Return Loss: These parameters are measured with the dipole
positioned under the liquid filled phantom. The impedance stated is transformed from the
measurement at the SMA connector to the feed point. The Return Loss ensures low
reflected power. No uncertainty required.
• Electrical Delay: One-way delay between the SMA connector and the antenna feed point.
No uncertainty required.
• SAR measured: SAR measured at the stated antenna input power.
• SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna
connector.
• SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the
nominal SAR result.
The reported uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage
probability of approximately 95%.
Certificate No: 02450V2-735_Dec15
Page 2 of 8
Measurement Conditions
DASY system confiquration, as far as not セ@ iven on paqe 1.
V52.8.8
DASY Version
DASY5
Extrapolation
Advanced Extrapolation
Phantom
Modular Flat Phantom
with Spacer
10mm
Distance Dipole Center - TSL
Zoom Scan Resolution
dx, dy, dz = 5 mm
Frequency
2450 MHz ± 1 MHz
Head TSL parameters
. parameters an d caIcu Iations
Th e fo II owing
were app11e
I' d
Nominal Head TSL parameters
Temperature
Permittivity
Conductivity
22.0 °C
39.2
1.80 mho/m
37.9 ± 6 %
1 .88 mho/m ± 6 %
----
----
(22.0 ± 0.2)
Measured Head TSL parameters
< 0.5 °C
Head TSL temperature change during test
SAR result with Head TSL
SAR averaged over 1 cm 3 (1 g) of Head TSL
SAR measured
Condition
normalized to 1W
SAR for nominal Head TSL parameters
SAR averaged over 10 cm3 (10 g) of Head TSL
SAR measured
13.4 W/kg
250 mW input power
52.1 W/kg
:t:
17.0 % (k=2)
condition
250 mW input power
6.20 W/kg
normalized to 1W
24.4 W/kg :t: 16.5 % (k=2)
SAR for nominal Head TSL parameters
Body TSL parameters
The followinq parameters and calculations were applied.
Nominal Body TSL parameters
Measured Body TSL parameters
Body TSL temperature change during test
Temperature
Permittivity
Conductivity
22.0 °C
52.7
1.95 mho/m
(22.0 ± 0.2) °C
52.2 ±6 %
2.03 mho/m ± 6 %
< 0.5 °C
----
----
SAR result with Body TSL
SAR averaged over 1 cm3 (1 g) of Body TSL
SAR measured
SAR for nominal Body TSL parameters
SAR averaged over 10 cm 3 (10 g) of Body TSL
SAR measured
SAR for nominal Body TSL parameters
Certificate No: D2450V2-735_Dec1 5
Condition
250 mW input power
13.3 W/kg
normalized to 1W
52.1 W/kg :t: 17.0 % (k=2)
condition
250 mW input power
6.21 W/kg
normalized to 1W
24.5 W/kg :t: 16.5 % (k=2)
Page 3 of 8
Appendix (Additional assessments outside the scope of SCS 0108)
Antenna Parameters with Head TSL
56.4 Q + 5.4 jQ
Impedance, transformed to feed point
Return Loss
- 22.1 dB
Antenna Parameters with Body TSL
53.1 Q + 7.8 jQ
Impedance, transformed to feed point
Return Loss
- 21 .8 dB
General Antenna Parameters and Design
Electrical Delay (one direction)
1.152 ns
After long term use with 1OOW radiated power, only a slight warming of the dipole near the feedpoint can be measured.
The dipole is made of standard semirigid coaxial cable . The center conductor of the feeding line is directly connected to the
second arm of the dipole. The antenna is therefore short-circuited for DC-signals. On some of the dipoles, small end caps
are added to the dipole arms in order to improve matching when loaded according to the position as explained in the
"Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still
according to the Standard.
No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the
feedpoint may be damaged.
Additional EUT Data
Manufactured by
SPEAG
Manufactured on
May 07, 2003
Certificate No: D2450V2-735_Dec15
Page 4 of 8
DASYS Validation Report for Head TSL
Date: 10.l2.2015
Test Laboratory: SPEAG, Zurich, Switzerland
DUT: Dipole 2450 MHz ; Type: D2450V2; Serial: D2450V2 - SN: 735
Communication System: UID O - CW; Frequency: 2450 MHz
Medium parameters used: f = 2450 MHz; CJ= l.88 Sim; Sr= 37.9; p = 1000 kg/m
Phantom section: Flat Section
Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19-201 l )
DASY52 Configuration:
•
Probe: EX3DV4- SN7349; ConvF(7.67, 7.67, 7.67); Calibrated: 30. 12.2014;
•
Sensor-Surface: 1.4mm (Mechanical Surface Detection)
•
Electronics: DAE4 Sn601; Calibrated: 17.08.2015
•
Phantom: Flat Phantom 5.0 (front); Type: QDOOOP50AA; Serial: 1001
•
DASY52 52.8.8(1222); SEMCAD X 14.6.10(733 1)
Dipole Calibration for Head Tissue/Pin=250 mW, d=lOmm/Zoom Scan (7x7x7)/Cube 0:
Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value= 112.7 Y/m; Power Drift= 0.07 dB
Peak SAR (extrapolated)= 27.9 W/kg
SAR(l g) = 13.4 W/kg; SAR(lO g) = 6.2 W/kg
Maximum value of SAR (measured) = 22.0 W/kg
dB
-4.80
-9.60
-19.20
-24.00
0 dB= 22.0 W/kg = 13.42 dBW/kg
Certificate No: D2450V2-735_Dec15
Page 5 of 8
Impedance Measurement Plot for Head TSL
10 Dec 2015
ln!I) S11
4: 56. 3'31 u
1 U FS
5 .4 414 u
14:42: 48
2 450.000 000 MHz
-----r----
'\
353.48 p H
- -- -...I
Del
CA
Avg
16
Hld
C H2
CA
S'.11
------- ---
4: - 22 071 d B
5 d B / REF - 20 dB
LOG
--.
----
__,/"""
セ@
セ@
2 4 50 000 000 MHz
--
i__....---
._,/
Hi d
STOP 2 650. 000 000 MHz
START 2 250. 000 000 MHz
Certificate No: 0 2450V2-735_Dec15
Page 6 of 8
DASY5 Validation Report for Body TSL
Date: 10.12.2015
Test Laboratory: SPEAG, Zurich, Switzerland
DUT: Dipole 2450 MHz ; Type: D2450V2; Serial: D2450V2 - SN: 735
Communication System: UID O - CW; Frequency: 2450 MHz
Medium parameters used: f = 2450 MHz; cr = 2.03 Sim; Er = 52.2; p = 1000 kg/m
Phantom section: Flat Section
Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19-201 l )
DASY52 Configuration:
•
Probe: EX3DV4- SN7349; ConvF(7.53, 7.53, 7.53); Calibrated: 30. 12.2014;
•
Sensor-Surface: 1.4mm (Mechanical Surface Detection)
•
Electronics: DAE4 Sn60l ; Calibrated: 17.08.2015
•
Phantom: Flat Phantom 5.0 (back); Type: QDOOOP50AA; Serial: 1002
•
DASY52 52.8.8( 1222); SEMCAD X 14.6.10(7331 )
Dipole Calibration for Body Tissue/Pin=250 mW, d=lOmm/Zoom Scan (7x7x7)/Cube 0:
Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value= 108.4 Y/m; Power Drift = 0.02 dB
Peak SAR (extrapolated)= 26.6 W/kg
SAR(l g) = 13.3 W/kg; SAR(lO g) = 6.21 W/kg
Maximum value of SAR (measured) = 22.0 W/kg
dB
· 4.80
-9.60
-U.40
-19.20
-24.00
0 dB= 22.0 W/kg = 13.42 dBW/kg
Certificate No: D2450V2-735_Dec15
Page 7 of 8
Impedance Measurement Plot for Body TSL
10 Dec 2015
[!ill S11
4: 53.094
1 U FS
7. 8184
----r------.
Del
..
16
C H2
'{
Hld
··------ . l -- --
S11
5 dB / REF -20 dB
LOG
-----セ@
Av 9
16
-\
Hl d
·-' .''' ,\\
4"- 21 791 dB
' 7 _,,..--
""' \
14:42:21
2 450.000 000 MHz
. . I
..
- LI . / /
-i __.....,,. '•
pH
\'
Av9
.-· -
Cil
n 507. 89
2 450 0 00 000 MHz
i.----
\I
S TOP 2 650. 000 000 MHz
START 2 250. 000 0 00 MHz
Certificate No: D2450V2· 735_Dec15
Page 8 of 8
Calibration Laboratory of
Schmid & Partner
Engineering AG
Service suisse d'etalonnage
Servizio svizzero di taratura
Zeughausstrasse 43, 8004 Zurich, Switzerland
Swiss Calibration Service
Accredited by the Swiss Accreditation Service (SAS)
Accreditation No.:
Schweizerischer Kalibrierdienst
SCS 0108
The Swiss Accreditation Service is one of the signatories to the EA
Multilateral Agreement for the recognition of calibration certificates
Client
Sporton-TW (Auden)
Certificate No:
05GHzV2-1128_Jul16
CALIBRATION CERTIFICATE
Object
05GHzV2 - SN:1128
Calibration procedure(s)
QA CAL-22.v2
Calibration procedure for dipole validation kits between 3-6 GHz
Calibration date:
July 27, 2016
This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (SI).
The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate.
All calibrations have been conducted in the closed laboratory facility: environment temperature (22 ± 3)°C and humidity < 70%.
Calibration Equipment used (M&TE critical for calibration)
Primary Standards
ID#
Cal Date (Certificate No.)
Scheduled Calibration
Power meter NAP
Power sensor NRP-Z91
SN: 104778
SN: 103244
06-Apr-16 (No. 217-02288/02289)
Apr-17
06-Apr-16 (No. 217-02288)
Power sensor NRP-Z91
SN: 103245
06-Apr-16 (No. 217-02289)
Apr-17
Apr-17
Reference 20 dB Attenuator
Type-N mismatch combination
SN: 5058 (20k)
SN: 5047.2 / 06327
05-Apr-16 (No. 217-02292)
05-Apr-16 (No. 217-02295)
Apr-17
Reference Probe EX3DV4
SN: 3503
30-Jun-16 (No. EX3-3503_Jun16)
Jun-17
DAE4
SN: 601
30-Dec-15 (No. DAE4-601 _Dec15)
Dec-16
Apr-17
Secondary Standards
ID#
Check Date (in house)
Scheduled Check
Power meter EPM-442A
Power sensor HP 8481A
SN: GB37480704
In house check: Oct-16
SN: US37292783
07-0ct-15 (No. 217-02222)
07-0ct-15 (No. 217-02222)
In house check: Oct-16
Power sensor HP 8481A
SN: MY41092317
07-0ct-15 (No. 217-02223)
In house check: Oct-16
RF generator R&S SMT-06
SN: 100972
15-Jun-15 (in house check Jun-15)
In house check: Oct-16
Network Analyzer HP 8753E
SN: US37390585
18-0ct-01 (in house check Oct-15)
In house check: Oct-16
Name
Function
Calibrated by:
Claudio Leubler
Laboratory Technician
Approved by:
Katja Pokovic
Technical Manager
s~
#~
Issued: July 27, 2016
This calibration certificate shall not be reproduced except in full without written approval of the laboratory.
Certificate No: D5GHzV2-1128_Jul16
Page 1 of 13
Calibration Laboratory of
Schmid & Partner
Engineering AG
Schweizerischer Kalibrierdienst
Service suisse d'etalonnage
Servizio svizzero di taratura
Zeughausstrasse 43, 8004 Zurich, Switzerland
Accredited by the Swiss Accreditation Service (SAS)
Accreditation No.:
Swiss Calibration Service
SCS 0108
The Swiss Accreditation Service is one of the signatories to the EA
Multilateral Agreement for the recognition of calibration certificates
Glossary:
TSL
ConvF
N/A
tissue simulating liquid
sensitivity in TSL / NORM x,y,z
not applicable or not measured
Calibration is Performed According to the Following Standards:
a) IEEE Std 1528-2013, "IEEE Recommended Practice for Determining the Peak SpatialAveraged Specific Absorption Rate (SAR) in the Human Head from Wireless
Communications Devices: Measurement Techniques", June 2013
b) IEC 62209-2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless
communication devices used in close proximity to the human body (frequency range of 30
MHz to 6 GHz)", March 2010
c) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz"
Additional Documentation:
d) DASY4/5 System Handbook
Methods Applied and Interpretation of Parameters:
• Measurement Conditions: Further details are available from the Validation Report at the end
of the certificate. All figures stated in the certificate are valid at the frequency indicated.
• Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed
point exactly below the center marking of the flat phantom section, with the arms oriented
parallel to the body axis.
• Feed Point Impedance and Return Loss: These parameters are measured with the dipole
positioned under the liquid filled phantom. The impedance stated is transformed from the
measurement at the SMA connector to the feed point. The Return Loss ensures low
reflected power. No uncertainty required.
• Electrical Delay: One-way delay between the SMA connector and the antenna feed point.
No uncertainty required.
• SAR measured: SAR measured at the stated antenna input power.
• SAR normalized: SAR as measured, normalized to an input power of 1 Wat the antenna
connector.
• SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the
nominal SAR result.
The reported uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage
probability of approximately 95%.
Certificate No: 05GHzV2-1128_Jul16
Page 2 of 13
Measurement Conditions
DASY sys em conf1Quraf10n, as f ar as not セ@ 1ven on page
DASY Version
DASYS
Extrapolation
Advanced Extrapolation
V52.8.8
Modular Flat Phantom V5.0
Phantom
Distance Dipole Center - TSL
Zoom Scan Resolution
10 mm
with Spacer
dx, dy = 4.0 mm, dz = 1.4 mm
Graded Ratio= 1.4 (Z direction)
5250 MHz± 1 MHz
5600 MHz ± 1 MHz
5750 MHz ± 1 MHz
Frequency
Head TSL parameters at 5250 MHz
The fo IIowing
. parameters an d caIcu Iat1ons
I" d
were app11e
Nominal Head TSL parameters
Measured Head TSL parameters
Head TSL temperature change during test
Temperature
Permittivity
Conductivity
22.0 °C
35.9
4.71 mho/m
(22.0 ± 0.2) °C
34.4 ±6 %
4.52 mho/m ± 6 %
< 0.5 °C
----
----
SAR result with Head TSL at 5250 MHz
SAR averaged over 1 cm (1 g) of Head TSL
SAR measured
SAR for nominal Head TSL parameters
SAR averaged over 10 cm3 (10 g) of Head TSL
SAR measured
SAR for nominal Head TSL parameters
Certificate No: D5GHzV2-1128_Jul16
Condition
100 mW input power
7.87 W/kg
normalized to 1W
77.9 W/kg ± 19.9 % (k=2)
condition
100 mW input power
2.27 W/kg
normalized to 1W
22.4 W/kg ± 19.5 % (k=2)
Page 3 of 13
Head TSL parameters at 5600 MHz
The following parameters and calculations were applied.
Nominal Head TSL parameters
Measured Head TSL parameters
Temperature
Permittivity
Conductivity
22.0 °c
35.5
5.07 mho/m
(22.0 ± 0.2) c
33.9 ±6 %
4.86 mho/m ± 6 %
< 0.5 °C
----
----
Head TSL temperature change during test
SAR result with Head TSL at 5600 MHz
SAR averaged over 1 cm3 (1 g) of Head TSL
SAR measured
Condition
100 mW input power
8.21 W/kg
normalized to 1W
81.2 W /kg± 19.9 % (k=2)
SAR for nominal Head TSL parameters
SAR averaged over 10 cm3 (1 O g) of Head TSL
SAR measured
condition
100 mW input power
2.36 W/kg
normalized to 1W
23.3 W/kg ± 19.5 % (k=2)
SAR for nominal Head TSL parameters
Head TSL parameters at 5750 MHz
The following parameters and calculations were applied
Nominal Head TSL parameters
Measured Head TSL parameters
Head TSL temperature change during test
Temperature
Permittivity
Conductivity
22.0 °c
35.4
5.22 mho/m
(22.0 ± 0.2) 0 c
33.7 ± 6 %
5.02 mho/m ± 6 %
< 0.5 °C
----
----
SAR result with Head TSL at 5750 MHz
SAR averaged over 1 cm3 (1 g) of Head TSL
SAR measured
SAR for nominal Head TSL parameters
SAR averaged over 10 cm (10 g) of Head TSL
SAR measured
SAR for nominal Head TSL parameters
Certificate No: D5GHzV2-1128_Jul16
Condition
100 mW input power
7.92 W/kg
normalized to 1W
78.3 W/kg ± 19.9 % (k=2)
condition
100 mW input power
2.27 W/kg
normalized to 1W
22.4 W/kg ± 19.5 % (k=2)
Page 4 of 13
Body TSL parameters at 5250 MHz
Tehof lowing
l . parameters and ca11·
cu at1ons were appl"d
1e
Nominal Body TSL parameters
Measured Body TSL parameters
Body TSL temperature change during test
Temperature
Permittivity
Conductivity
22.0 °C
48.9
5.36 mho/m
(22.0 ± 0.2) °C
47.1 ±6 %
5.42 mho/m ± 6 %
< 0.5 °C
_.........
----
SAR result with Body TSL at 5250 MHz
SAR averaged over 1 cm3 (1 g) of Body TSL
SAR measured
Condition
100 mW input power
7.51 W/kg
normalized to 1W
74.5 W/kg ± 19.9 % (k=2)
SAR for nominal Body TSL parameters
SAR averaged over 1O cm3 (1 O g) of Body TSL
SAR measured
condition
100 mW input power
2. 12 W/kg
normalized to 1W
21.0 W/kg :1: 19.5 % (k=2)
SAR for nominal Body TSL parameters
Body TSL parameters at 5600 MHz
The fo II owing
. parameters and caIcu Iations were applied.
Nominal Body TSL parameters
Measured Body TSL parameters
Body TSL temperature change during test
Temperature
Permittivity
Conductivity
22.0 °C
48.5
5.77 mho/m
46.5 ±6 %
5.88 mho/m ± 6 %
----
----
(22.0 ± 0.2)
< 0.5 °C
SAR result with Body TSL at 5600 MHz
SAR averaged over 1 cm3 (1 g) of Body TSL
SAR measured
SAR for nominal Body TSL parameters
SAR averaged over 1O cm (10 g) of Body TSL
SAR measured
SAR for nominal Body TSL parameters
Certificate No: D5GHzV2-1128_Jul16
Condition
100 mW input power
7.86 W/kg
normalized to 1W
78.0 W/kg ± 19.9 % (k=2)
condition
100 mW input power
2.21 W/kg
normalized to 1W
21.9 W/kg ± 19.5 % (k=2)
Page 5 of 13
Body TSL parameters at 5750 MHz
Tehof lowing
l ' paramet ers and
calcu laf ions were appI'd
,e
Nominal Body TSL parameters
Measured Body TSL parameters
Body TSL temperature change during test
Temperature
Permittivity
Conductivity
22.0 °c
48.3
5.94 mho/m
(22.0 ± 0.2) °C
46.2 ±6 %
6.11 mho/m ± 6 %
< 0.5 °C
----
----
SAR result with Body TSL at 5750 MHz
SAR averaged over 1 cm3 (1 g) of Body TSL
Condition
SAR measured
SAR for nominal Body TSL parameters
SAR averaged over 10 cm3 (1 O g) of Body TSL
SAR measured
SAR for nominal Body TSL parameters
Certificate No: D5GHzV2-1128 Jul16
100 mW input power
7.67 W/kg
normalized to 1W
76.1 W/kg ± 19.9 % (k=2)
condition
100 mW input power
2.14 W/kg
normalized to 1W
21.2 W/kg :t 19.5 % (k=2)
Page 6 of 13
Appendix (Additional assessments outside the scope of SCS 0108)
Antenna Parameters with Head TSL at 5250 MHz
Impedance, transformed to feed point
51 .6 Q - 3.0 jQ
Return Loss
- 29.5 dB
Antenna Parameters with Head TSL at 5600 MHz
56.1 Q + 1.7 jQ
Impedance, transformed to feed point
Return Loss
- 24.6 dB
Antenna Parameters with Head TSL at 5750 MHz
53.9 Q + 3.2 jQ
Impedance, transformed to feed point
- 26.2 dB
Return Loss
Antenna Parameters with Body TSL at 5250 MHz
49.8 Q - 1.3 jQ
Impedance, transformed to feed point
- 37.6 dB
Return Loss
Antenna Parameters with Body TSL at 5600 MHz
57.4 Q + 1.9 jQ
Impedance, transformed to feed point
- 23.0 dB
Return Loss
Antenna Parameters with Body TSL at 5750 MHz
54.8 Q + 2.6 jQ
Impedance, transformed to feed point
- 25.6 dB
Return Loss
General Antenna Parameters and Design
1.203 ns
Electrical Delay (one direction)
After long term use with 1OOW radiated power, only a slight warming of the dipole near the feedpoint can be measured.
The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the
second arm of the dipole. The antenna is therefore short-circuited for DC-signals. On some of the dipoles, small end caps
are added to the dipole arms in order to improve matching when loaded according to the position as explained in the
"Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still
according to the Standard.
No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the
feedpoint may be damaged.
Additional EUT Data
Manufactured by
SPEAG
Manufactured on
September 08, 2011
Certificate No: D5GHzV2-1128_Jul16
Page 7 of 13
DASY5 Validation Report for Head TSL
Date: 27.07.2016
Test Laboratory: SPEAG, Zurich, Switzerland
DUT: Dipole D5GHzV2; Type: D5GHzV2; Serial: D5GHzV2 - SN:1128
Communication System: UID O - CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz
Medium parameters used: f = 5250 MHz; cr = 4.52 Sim; tr = 34.4; p = 1000 kg/m3
Medium parameters used: f = 5600 MHz; cr = 4.86 Sim; Sr= 33.9; p = 1000 kg/m3
Medium parameters used: f = 5750 MHz; cr = 5.02 Sim; tr = 33.7; p = 1000 kglm3
Phantom section: Flat Section
Measurement Standard: DASY5 (IEEEIIECIANSI C63.19-201 l)
DASY52 Configuration:
•
Probe: EX3DV4 - SN3503; ConvF(5.42, 5.42, 5.42); Calibrated: 30.06.2016, ConvF(4.89, 4.89,
4.89); Calibrated: 30.06.2016, ConvF(4.85, 4.85, 4.85); Calibrated: 30.06.2016;
•
Sensor-Surface: 1.4mm (Mechanical Surface Detection)
•
Electronics: DAE4 Sn601; Calibrated: 30.12.2015
•
Phantom: Flat Phantom 5.0 (front); Type: QDOOOP50AA; Serial: 1001
•
DASY52 52.8.8(1258); SEMCAD X 14.6.10(7372)
Dipole Calibration for Head Tissue/Pin=lOOmW, dist=lOmm, f=5250 MHz/Zoom Scan,
dist=l.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz= 1.4mm
Reference Value = 73.50 Vim; Power Drift= 0.00 dB
Peak SAR (extrapolated) = 28.9 W/kg
SAR(l g) =7.87 W/kg; SAR(lO g) =2.27 W/kg
Maximum value of SAR (measured) = 18.1 Wlkg
Dipole Calibration for Head Tissue/Pin=lOOmW, dist=lOmm, f=5600 MHz/Zoom Scan,
dist=l.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=l.4mm
Reference Value = 73.50 Vim; Power Drift= 0.00 dB
Peak SAR (extrapolated)= 32.4 Wlkg
SAR(l g) =8.21 W/kg; SAR(lO g) =2.36 W/kg
Maximum value of SAR (measured) = 19.6 W/kg
Dipole Calibration for Head Tissue/Pin=lOOmW, dist=lOmm, f=5750 MHz/Zoom Scan,
dist=l.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz= l .4mm
Reference Value = 71.33 Vim; Power Drift = 0.01 dB
Peak SAR (extrapolated)= 32.0 Wlkg
SAR(l g) =7.92 W/kg; SAR(lO g) =2.27 W/kg
Maximum value of SAR (measured)= 19.0 W/kg
Certificate No: D5GHzV2-1128_Jul16
Page 8 of 13
dB
-5.00
-10.00
-15.00
-20.00
-25.00
0 dB = 18.1 W/kg = 12.58 dBW/kg
Certificate No: D5GHzV2-1128_Jul16
Page 9 of 13
Impedance Measurement Plot for Head TSL
2 7 J ul
[E1J S11
1 U FS
1: 51.548 il
-2.9 7 45 il
201 6
10. 191 pF
1 0:45:46
5 250.000 000 MHz
CH1 Markers
Del
2 : 56. 055
-,1
fl
1 . 5719 il
5.50000 GH z
3: 5:3. '345 (,!
3 . 2109 (,!
5. 75000 GHz
Hld
CH2
S11
LOG
~ 5 dB/ REF -20 ~dB
.,.
- ~ - -- - - -c.:i
1:-29.50~ dB
_..
-------+
5 _750. 000~000 MHz
CH2 Markers
- - -~ - -- ---~
2:-24.550 dB
5. 60000 GHz
3:- 26.209 dB
5.75000 GH z
Hld
STOP 5 000. 000 000 MHz
START 5 000.000 000 MHz
Certificate No: D5GHzV2-1128_Jul16
Page 10 of 13
DASYS Validation Report for Body TSL
Date: 26.07.2016
Test Laboratory: SPEAG, Zurich, Switzerland
OUT: Dipole D5GHzV2; Type: D5GHzV2; Serial: D5GHzV2 - SN:1128
Communication System: UID 0- CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz
Medium parameters used: f = 5250 MHz; a= 5.42 Sim; tr = 47.1; p = 1000 kg/m
Medium parameters used: f = 5600 MHz; a= 5.88 Sim; tr = 46.5; p = 1000 kg/m
Medium parameters used: f = 5750 MHz; a = 6.11 Sim; tr = 46.2; p = 1000 kg/m 3
Phantom section: Flat Section
Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19-2011)
DASY52 Configuration:
•
Probe: EX3DV4 - SN3503; ConvF(4.85, 4.85, 4.85); Calibrated: 30.06.2016, ConvF(4.35, 4.35,
4.35); Calibrated: 30.06.2016, ConvF(4.3, 4.3, 4.3); Calibrated: 30.06.2016;
•
Sensor-Surface: 1.4mm (Mechanical Surface Detection)
•
Electronics: DAE4 Sn601; Calibrated: 30.12.2015
•
Phantom: Flat Phantom 5.0 (back); Type: QDOOOP50AA; Serial: 1002
•
DASY52 52.8.8(1258); SEMCAD X 14.6.10(7372)
Dipole Calibration for Body Tissue/Pin=lOOmW, dist=lOmm, f=5250MHz/Zoom Scan,
dist=l.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz= l.4mm
Reference Value = 67.75 V/m; Power Drift = -0.01 dB
Peak SAR (extrapolated) = 28.4 W/kg
SAR(l g) =7.51 W/kg; SAR(lO g) =2.12 W/kg
Maximum value of SAR (measured) = 17 .5 W /kg
Dipole Calibration for Body Tissue/Pin=lOOmW, dist=lOmm, f=5600 MHz/Zoom Scan,
dist=l.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz= l.4mm
Reference Value= 67.02 V/m; Power Drift= -0.04 dB
Peak SAR (extrapolated) = 32.5 W/kg
SAR(l g) =7.86 W/kg; SAR(lO g) =2.21 W/kg
Maximum value of SAR (measured)= 18.7 W/kg
Dipole Calibration for Body Tissue/Pin=lOOmW, dist=lOmm, f=5750 MHz/Zoom Scan,
dist=l.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=l.4mm
Reference Value = 65.29 V/m; Power Drift= -0.02 dB
Peak SAR (extrapolated)= 33.1 W/kg
SAR(l g) =7.67 W/kg; SAR(lO g) =2.14 W/kg
Maximum value of SAR (measured) = 18.5 W/kg
Certificate No: D5GHzV2-1128_Jul16
Page 11 of 13
dB
-5.00
-10.00
-15.00
-20.00
-25.00
0 dB = 18.5 W/kg = 12.67 dBW/kg
Certificate No: D5GHzV2-1128_Jul16
Page 12 of 13
Impedance Measurement Plot for Body TSL
25 Jul 2015
[lill S 11
1 U FS
1: 49. 838
セ@
- 1 . 3 105
{l
23.132 p F
18:07:48
5 250. 000 000 MH z
CH1 Markers
De l
Co r
2: 57e3 89 fl
1.91 0 2 {l
5.6 0000 GHz
3 : 54. 845 セ@
2. 5211 r,
5.75000 GH z
,-
Hld
CH2
S11
LOG
~5 dB/ REF - 20 jB
1:-3 7. 5 55 dB
5 ) 50.0 00 000 MHz
CH2 Marke r s
Co r
2:-22.955 dB
5.50000 GHz
3:-2 5 . 5 8 5 dB
5.75000 GHz
Avg
16
_,_
Hld
____.____
_,_
STOP 5 000. 000 00 0 MHz
Certificate No: D5GHzV2-1128_Jul16
Page 13 of 13
Calibration Laboratory of
Schmid & Partner
Engineering AG
Zeughausstrasse 43, 8004 Zurich, Switzerland
Schweizerischer Kalibrierdienst
Service suisse d'etalonnage
Servizio svizzero di taratura
Swiss Calibration Service
Accreditatio n No.:
Accredited by the Swiss Accreditation Service (SAS)
The Swiss Accreditatio n Service is one of the signatories to the EA
Multilateral Agreement for the recognition of calibration certificates
Client
Certificate No:
Sporton -TW (Auden)
SCS 0108
DAE3-49 5_May1 6
CALIBRATION CERTIFICATE
Object
DAE3 - SD 000 003 AD - SN: 495
Calibration procedure(s)
QA CAL-06.v29
Calibration procedure for the data acquisition electronics (DAE)
Calibration date:
May 27, 2016
units of measureme nts (SI).
This calibration certificate documents the traceability to national standards, which realize the physical
pages and are part of the certificate.
The measurements and the uncertainties with confidence probability are given on the following
(22 ± 3}°C and humidity < 70%.
All calibrations have been conducted in the closed laboratory facility: environment temperature
Calibration Equipment used (M&TE critical for calibration)
Primary Standards
Keithley Multimeter Type 2001
j SN: 0810278
Cal Date (Certificate No.)
Scheduled Calibration
09-Sep-15 (No:17153)
Sep-16
Check Date (in house)
Scheduled Check
Secondary Standards
ID#
Auto DAE Calibration Unit
Calibrator Box V2.1
SE UWS 053 AA 1001 05-Jan-16 (in house check)
SE UMS 006 AA 1002 05-Jan-16 (in house check)
Name
Function
Calibrated by:
R.Mayoraz
Technician
Approved by:
Fin Bomholt
In house check: Jan-17
In house check: Jan-17
Signature
Deputy Technical Manager
Issued: May 27, 2016
laboratory.
This calibration certificate shall not be reproduced except in full without written approval of the
Certificate No: DAE3-495_ May16
Page 1 of 5
Calibration Laboratory of
Schmid & Partner
Engineering AG
Zeughausstrasse 43, 8004 Zurich, Switzerland
Schweizerisc her Kalibrierdiens t
Service suisse d'etalonnage
Servizio svizzero di taratura
Swiss Calibration Service
Accreditation No.:
Accredited by the Swiss Accreditation Service (SAS)
SC$ 0108
The Swiss Accreditation Service is one of the signatories to the EA
Multilateral Agreement for the recognition of calibration certificates
Glossary
DAE
Connecto r angle
data acquisition electronics
information used in DASY system to align probe sensor X to the robot
coordinate system.
Methods Applied and Interpretation of Parameters
DC Voltage Measurement: Calibration Factor assessed for use in DASY system by
•
comparison with a calibrated instrument traceable to national standards . The figure given
corresponds to the full scale range of the voltmeter in the respective range.
•
•
Connector angle: The angle of the connector is assessed measuring the angle
mechanically by a tool inserted. Uncertainty is not required.
The following parameters as documented in the Appendix contain technical information as a
result from the performance test and require no uncertainty.
•
•
•
•
•
•
•
•
•
DC Voltage Measurement Linearity: Verification of the Linearity at + 10% and -10% of
the nominal calibration voltage. Influence of offset voltage is included in this
measurement.
Common mode sensitivity: Influence of a positive or negative common mode voltage on
the differential measurement.
Channel separation: Influence of a voltage on the neighbor channels not subject to an
input voltage.
AD Converter Values with inputs shorted: Values on the internal AD converter
corresponding to zero input voltage
Input Offset Measurem ent Output voltage and statistical results over a large number of
zero voltage measurements.
Input Offset Current: Typical value for information; Maximum channel input offset
current, not considering the input resistance.
Input resistance: Typical value for information: DAE input resistance at the connector,
during internal auto-zeroing and during measurement.
Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery
alarm signal is generated.
Power consumption: Typical value for information. Supply currents in various operating
modes.
Certificate No: DAE3-495_May16
Page 2 of 5
DC Voltage Measurem ent
AID - Converter Resolution nominal
full range = -100... +300 mV
6.1µV,
1LSB =
High Range:
full range = -1 .......+3mV
61 nV ,
1LSB =
Low Range:
DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec
High Range
404.392 ± 0.02% (k=2)
405.369 ± 0.02% (k=2)
405.725 ± 0.02% (k=2)
Low Range
3.95295 ± 1.50% (k=2)
3.99096 ± 1.50% (k=2)
3.96580 ± 1.50% (k=2)
Calibration Factors
Connecto r Angle
78.0 ° ± 1 °
Connector Angle to be used in DASY system
Certificate No: DAE3-495_May16
Page 3 of 5
Appendix (Additional assessments outside the scope of SCS01 08)
1. DC Voltaae Linearity
High Range
Reading (µV)
Difference (µV)
Error(%)
Channel X
+ Input
199996.62
1.58
0.00
ChannelX
+ Input
20000.74
-0.12
-0.00
ChannelX
- Input
-19996.44
4.68
-0.02
ChannelY
+ Input
199995.94
1.53
0.00
ChannelY
+ Input
20002.54
1.56
0.01
ChannelY
- Input
-19999.75
1.29
-0.01
Channel Z
+ Input
199992.83
-1.82
-0.00
ChannelZ
+ Input
20002.61
1.74
0.01
ChannelZ
- Input
-19998.46
2.69
-0.01
Reading (µV)
Difference (µV)
Low Range
Error(%)
ChannelX
+ Input
2001.48
0.75
0.04
ChannelX
+ Input
201.55
0.46
0.23
ChannelX
- Input
-198.32
0.30
-0.15
ChannelY
+ Input
2000.13
-0.57
-0.03
ChannelY
+ Input
200.91
-0.45
-0.22
ChannelY
- Input
-199.30
-0.77
0.39
Channel Z
+ Input
1999.63
-0.96
-0.05
ChannelZ
+ Input
200.82
-0.44
-0.22
ChannelZ
- Input
-199.88
-1.27
0.64
2. Common mode sensitivity
DASY measurement parameters· Auto Zero Time· 3 sec· Measuring time· 3 sec
Common mode
Input Voltage (mV)
ChannelX
ChannelY
Channel Z
High Range
Average Reading (µV)
Low Range
Average Reading (µV)
200
3.18
2.27
- 200
-2 .19
-3.80
200
0.69
0.05
- 200
-0.39
-0.92
200
2.28
2.22
- 200
-4.44
-4.68
3. Channel separation
DASY measurement parameters: Auto Zero Time: 3 sec; Measurina time: 3 sec
Input Voltage (mV)
Channel X (µV)
Channel Y (µV)
Channel Z (µV)
ChannelX
200
-0.76
-2.16
ChannelY
200
7.44
-0.52
ChannelZ
200
5.77
5.68
Certificate No: DAE3-495_May16
Page 4 of 5
4. AD-Conve rter Values with inputs shorted
DASY measurement parameters: A uto Zero T1me: 3 sec; Measuring time: 3 sec
High Range (LSB)
Low Range (LSB)
ChannelX
15817
17431
ChannelY
15765
17509
Channel Z
15903
17029
5. Input Offset Measurem ent
DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec
Input 10MQ
Average (µV)
min. Offset (µV)
max. Offset (µV)
Std. Deviation
(µV)
ChannelX
-0.1 5
-1.92
1.72
0.56
ChannelY
0.33
-0.86
2.13
0.60
Channell
-1.62
-2.91
-0.07
0.62
6. Input Offset Current
Nominal Input circuitry offset current on all channels: <25fA
7. I nput R es1stance (Typical values for information)
Zeroing (kOhm)
Measuring (MOhm)
ChannelX
200
200
Channel Y
200
200
Channel Z
200
200
o taqe (Typical values for information)
8. Low Batterv Alarm VI
Typical values
Alarm Level (VDC)
Supply(+ Vee)
+7.9
Supply(· Vee)
-7.6
9. Power Consumpt1on
(Tvpical values for information)
Typical values
Switched off (mA)
Stand by (mA)
Transmitting (mA)
Supply(+ Vee)
+0.01
+6
+14
Supply (- Vee)
--0.01
-8
-9
Certificate No: DAE3-495_May16
Page 5 of 5
Calibration Laboratory of
Schmid & Partner
Engineering AG
Zeughausstrasse 43, 8004 Zurich, Switzerland
Accredited by the Swiss Accreditation Service (SAS)
The Swiss Accreditation Service is one of the signatories to the EA
Schweizerisc her Kalibrierdiens t
Service suisse d'etalonnage
Servizio svizzero di taratura
Swiss Calibration Service
Accreditation No.:
SCS 0108
Multilateral Agreement for the recognition of calibration certificates
Client
Sporton -TW (Auden)
Certificate No:
DAE4-n8_ May1 6
CALIBRATION CERTIFICATE
Object
DAE4- SD 000 D04 BM - SN: 778
Calibration procedure(s)
QA CAL-06.v2 9
Calibration procedure for the data acquisition electronics (DAE)
Calibration date:
May 12, 2016
This calibration certificate documents the traceability to national standards, which realize the physical units of measurements
(SI).
The measurements and the uncertainties with confidence probability are given on the following pages and are part
of the certificate.
All calibrations have been conducted in the closed laboratory facility: environment temperature (22 ± 3)°C and humidity
< 70%.
Calibration Equipment used (M&TE critical for calibration)
Primary Standards
Keithley Multimeter Type 2001
Secondary Standards
SN: 0810278
Cal Date (Certificate No.)
09-Sep-15 (No:17153)
Scheduled Calibration
Sep-16
ID#
Check Date (in house)
SE UWS 053 AA 1001 05-Jan-16 (in house check)
SE UMS 006 AA 1002 05-Jan-16 (in house check)
Scheduled Check
Auto DAE Calibration Unit
Calibrator Box V2.1
Name
Function
Signature
Calibrated by:
Dominique Steffen
Technician
Approved by:
Fin Bomholt
In house check: Jan-17
In house check: Jan-1 7
Deputy Technical Manager
Issued: May 12, 2016
This calibration certificate shall not be reproduced except in full without written approval of the laboratory.
Certificate No: DAE4-778_M ay16
Page 1 of 5
Calibration Laboratory of
Schmid & Partner
Engineering AG
Zeughausstrasse 43, 8004 Zurich, Switzerland
Accredited by the Swiss Accreditation Service (SAS)
The Swiss Accreditation Service is one of the signatories to the EA
Multilateral Agreement for the recognition of calibration certificates
Glossary
DAE
Connecto r angle
Schweizerisc her Kalibrierdiens t
Service sulsse d'etalonnage
Servizio svizzero di taratura
Swiss Calibration Service
Accreditation No.:
SCS 0108
data acquisition electronics
information used in DASY system to align probe sensor X to the robot
coordinate system.
Methods Applied and Interpretation of Parameters
•
DC Voltage Measurement: Calibration Factor assessed for use in DASY system by
compariso n with a calibrated instrumen t traceable to national standards. The figure given
correspon ds to the full scale range of the voltmeter in the respective range.
•
Connecto r angle: The angle of the connector is assessed measuring the angle
mechanic ally by a tool inserted. Uncertain ty is not required.
•
The following paramete rs as document ed in the Appendix contain technical informatio n as a
result from the performan ce test and require no uncertainty.
•
DC Voltage Measurem ent Linearity: Verification of the Linearity at +10% and -10% of
the nominal calibration voltage. Influence of offset voltage is included in this
measurem ent.
•
Common mode sensitivity: Influence of a positive or negative common mode voltage on
the differential measurement.
•
Channel separation: Influence of a voltage on the neighbor channels not subject to an
input voltage.
•
AD Converter Values with inputs shorted: Values on the internal AD converter
corresponding to zero input voltage
•
Input Offset Measurem ent Output voltage and statistical results over a large number of
zero voltage measurem ents.
•
Input Offset Current: Typical value for information; Maximum channel input offset
current, not considering the input resistance .
•
Input resistance: Typical value for information: DAE input resistance at the connector,
during internal auto-zeroing and during measurem ent.
•
Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery
alarm signal is generated.
•
Power consumption: Typical value for information. Supply currents in various operating
modes.
Certificate No: DAE4-778_M ay16
Page 2 of 5
DC Voltage Measurement
AID - Converter Resolution nominal
High Range:
1LS8 =
6.1µV,
full range= -100 ... +300 mV
Low Range:
1LSB =
61 nV ,
full range= -1.. .. ... +3mV
DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec
Calibration Factors
High Range
404.712 ± 0.02% (k=2)
403.516 ± 0.02% (k=2)
405.068 ± 0.02% (k=2)
Low Range
3.98678 ± 1.50% (k=2)
3.96495 ± 1.50% (k=2)
4.00091 ± 1.50% (k=2)
Connector Angle
Connector Angle to be used in DASY system
Certificate No: DAE4-778_May16
270.0 ° ± 1 °
Page 3 of 5
Appendix (Additional assessments outside the scope of SCS0108)
1. DC Vo Itage L"mearuy
High Range
Reading (µV)
Difference (µV)
Error(%)
ChannelX
+ Input
200032.14
·1.38
-0.00
ChannelX
+ Input
20005.68
0.79
0.00
ChannelX
- Input
-20003.61
1.31
-0.01
ChannelY
+ Input
200030.28
-3.73
-0.00
Channel¥
+ Input
20006.01
1.25
0.01
ChannelY
- Input
-20003.00
1.89
-0.01
ChannelZ
+ Input
200035.46
1.52
0.00
Channel Z
+ Input
20002.36
-2.31
-0.01
Channel Z
- Input
-20008.31
-3.27
0.02
Reading (µV)
Difference (µV)
Low Range
Error (%)
ChannelX
+ Input
2001.27
0.01
0.00
ChannelX
+ Input
201.37
0.21
0.10
ChannelX
- Input
-198.61
-0.02
0.01
ChannelY
+ Input
2001.38
0.24
0.01
Channel¥
+ Input
200.13
-0.97
-0.48
ChannelY
- Input
-198.84
-0.10
0.05
ChannelZ
+ Input
2001.29
0.21
0.01
ChannelZ
+ Input
200.34
-0.69
-0.34
ChannelZ
- Input
-200.58
-1.74
0.88
2. Common mode sensitivity
DASY measurement paramet ers: A uo
t Z ero T1me: 3 sec; Measunng f1me: 3 sec
Common mode
Input Voltage (mV)
Channel X
ChannelY
Channel Z
High Range
Average Reading {µV)
Low Range
Average Reading {µV)
200
-4.35
-5.61
- 200
7.07
5.78
200
-1.79
-1.82
- 200
0.49
0.20
200
-12.55
-12.56
-200
10.17
10.19
3. Channel separation
DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec
Input Voltage {mV)
Channel X (µV)
Channel Y {µV)
Channel Z {µV)
ChannelX
200
-0.66
-2.54
ChannelY
200
8.70
-0.26
ChannelZ
200
3.71
7.16
Certificate No: DAE4-778_May16
Page 4 of 5
4. AD-Converter Values with inputs shorted
DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec
High Range (LSB)
Low Range (LSB)
ChannelX
16054
16869
ChannelY
16191
17846
ChannelZ
16441
16314
5. Input Offset Measurement
DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec
Input 10MQ
Average (µV)
min. Offset (µV)
max. Offset (µ V)
Std. Deviation
(µV)
ChannelX
0.48
·0.60
1.44
0.42
ChannelY
-0.09
-1.42
2.50
0.58
ChannelZ
-1.11
-2.45
-0.19
0.45
6. Input Offset Current
Nominal Input circuitry offset current on all channels: <25fA
7. Inpu t Res1s
. t ance
(Typical values for information)
Zeroing (kOhm)
Measuring (MOhm)
ChannelX
200
200
ChannelY
200
200
ChannelZ
200
200
8. Low Battery Al arm V0 Itage
Typical values
(Typical values or information
Alarm Level (VDC)
Supply(+ Vee)
+7.9
Supply (- Vee)
-7.6
9. power Consumpf10n (Typical values for information)
Typical values
Switched off (mA)
Stand by (mA)
Transmitting (mA)
Supply(+ Vee)
+0.01
+6
+14
Supply (- Vee)
- O.Q1
-8
-9
Certificate No: DAE4-778_May16
Page 5 of 5
Calibration Laboratory of
Schmid & Partner
Engineering AG
Schweizerischer Kalibrierdienst
Service suisse d'etalonnage
Servizio svizzero di taratura
Zeughausstrasse 43, 8004 Zurich, Switzerland
Accredited by the Swiss Accreditation Service (SAS)
Accreditation No.:
Swiss Calibration Service
SCS 0108
The Swiss Accreditation Service is one of the signatories to the EA
Multilateral Agreement for the recognition of calibration certificates
Client
Sporton-TW (Auden)
Certificate No:
EX3-3925_May16
CALIBRATION CERTIFICATE
Object
EX3DV4 - SN:3925
Calibration procedure(s)
QA CAL-01.v9, QA CAL-14.v4, QA CAL-23.v5, QA CAL-25.v6
Calibration procedure for dosimetric E-field probes
Calibration date:
May 26, 2016
This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (SI).
The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate.
All calibrations have been conducted in the closed laboratory facility: environment temperature (22 ± 3)°C and humidity< 70% .
Calibration Equipment used (M&TE critical for calibration)
Primary Standards
ID
Cal Date (Certificate No.)
Scheduled Calibration
Power meter NRP
SN: 104778
06-Apr-16 (No. 217-02288/02289)
Apr-17
Power sensor NRP-Z91
SN: 103244
06-Apr-16 (No. 217-02288)
Apr-17
Power sensor NRP-Z91
SN: 103245
06-Apr-16 (No. 217-02289)
Apr-17
Reference 20 dB Attenuator
SN: S5277 (20x)
05-Apr-16 (No. 217-02293)
Apr-17
Reference Probe ES3DV2
SN: 3013
31-Dec-15 (No. ES3-3013 Dec15)
Dec-16
DAE4
SN: 660
23-Dec-15 (No. DAE4-660 Dec15)
Dec-16
Scheduled Check
Secondary Standards
ID
Check Date (in house)
Power meter E4419B
SN: GB41293874
06-Apr-16 (No. 217-02285/02284)
In house check: Jun-1 6
PowersensorE4412A
SN: MY41498087
06-Apr-16 (No. 217-02285)
In house check: Jun-16
PowersensorE4412A
SN: 000110210
06-Apr-16 (No. 217-02284)
In house check: Jun-16
RF generator HP 8648C
SN: US3642U01700
04-Aug-99 (in house check Apr-13)
In house check: Jun-16
Network Analyzer HP 8753E
SN: US37390585
18-0ct-01 (in house check Oct-15)
In house check: Oct-16
Name
Function
Calibrated by:
Leif Klysner
Laboratory Technician
Approved by:
Katja Pokovic
Technical Manager
Signature
セ@
セ@
Issued: May 31 , 2016
This calibration certificate shall not be reproduced except in full without written approval of the laboratory.
Certificate No: EX3-3925_May16
Page 1 of 11
Calibration Laboratory of
Schmid & Partner
Engineering AG
Zeughausstrasse 43, 8004 Zurich, Switzerland
Schweizerischer Kalibrierdienst
Service suisse d'etalonnage
Servizio svizzero di taratura
Swiss Calibration Service
Accreditation No.:
Accredited by the Swiss Accreditation Service (SAS)
SCS 0108
The Swiss Accreditation Service is one of the signatories to the EA
Multilateral Agreement for the recognition of calibration certificates
Glossary:
TSL
NORMx,y,z
ConvF
DCP
CF
A, B, C,D
Polarization  1800 MHz: R22 waveguide).
•
•
•
•
•
•
•
•
NORMx,y,z are only intermediate values, i.e., the uncertainties of NORMx,y,z does not affect the E -field
uncertainty inside TSL (see below ConvF).
NORM(f)x,y,z == NORMx,y,z * frequency_response (see Frequency Response Chart). This linearization is
implemented in DASY4 software versions later than 4.2. The uncertainty of the frequency response is included
in the stated uncertainty of ConvF.
DCPx,y,z: DCP are numerical linearization parameters assessed based on the data of power sweep with CW
signal (no uncertainty required). DCP does not depend on frequency nor media.
PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on the signal
characteristics
Ax,y,z; Bx,y,z; Cx,y,z; Dx,y,z; VRx,y,z: A, 8, C, D are numerical linearization parameters assessed based on
the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor
media. VR is the maximum calibration range expressed in RMS voltage across the diode.
ConvF and Boundary Effect Parameters: Assessed in flat phantom using E-field (or Temperature Transfer
Standard for f s 800 MHz) and inside waveguide using analytical field distributions based on power
measurements for f > 800 MHz. The same setups are used for assessment of the parameters applied for
boundary compensation (alpha, depth) of which typical uncertainty values are given. These parameters are
used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds
to NORMx,y,z * ConvF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent
ConvF is used in DASY version 4.4 and higher which allows extending the validity from± 50 MHz to ± 100
MHz.
Spherical isotropy (30 deviation from isotropy): in a field of low gradients realized using a flat phantom
exposed by a patch antenna.
Sensor Offset: The sensor offset corresponds to the offset of virtual measurement center from the probe tip
(on probe axis). No tolerance required.
Connector Angle: The angle is assessed using the information gained by determining the NORMx (no
uncertainty required).
Certificate No: EX3-3925_May16
Page 2 of 11
May 26, 2016
EX3DV4 - SN:3925
Probe EX3DV4
SN :3925
Manufactured:
Calibrated:
March 8, 2013
May 26, 2016
Calibrated for DASY/EASY Systems
(Note: non-compatible with DASY2 system!)
Certificate No: EX3-3925_May16
Page 3 of 11
EX3DV4- SN:3925
May 26, 2016
DASY/EASY - Parameters of Probe: EX3DV4 - SN :3925
Basic Calibration Parameters
Norm (uV/(V/m)2t
DCP(mV)"
Sensor X
Sensor Y
SensorZ
Unc (k=2)
0.59
96.5
0.52
97.9
0.50
± 10.1 %
98.9
Modulation Calibration Parameters
UID
Communication System Name
cw
dB
dBvµV
dB
VR
mV
Unc"
(k=2)
0.0
0.0
0.0
0.0
0.0
0.0
1.0
1.0
1.0
0.00
152.6
143.7
138.9
±2.7 %
The reported uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage
probability of approximately 95%.
The uncertainties of Norm X,Y,Z do not affect the E 2-field uncertainty inside TSL (see Pages 5 and 6).
Numerical linearization parameter: uncertainty not required.
E Uncertainty is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the
field value.
Certificate No: EX3-3925_May16
Page 4 of 11
EX3DV4- SN:3925
May 26, 2016
DASY/EASY - Parameters of Probe: EX3DV4 - SN :3925
Calibration Parameter Determined in Head Tissue Simulating Media
f (MHz) c
Relative
Permittivitv F
Conductivity
IS/ml F
ConvF X
ConvF Y
ConvF Z
AlphaG
DepthG
(mm)
Unc
(k=2)
750
41.9
0.89
10.37
10.37
10.37
0.48
0.80
+ 12.0 %
835
41.5
0.90
9.92
9.92
9.92
0.47
0.81
+ 12.0 %
900
41.5
0.97
9.72
9.72
9.72
0.41
0.80
+ 12.0 %
1750
40.1
1.37
8.57
8.57
8.57
0.29
0.80
+ 12.0 %
1900
40.0
1.40
8.30
8.30
8.30
0.30
0.80
+ 12.0 %
2000
40.0
1.40
8.26
8.26
8.26
0.30
0.80
+ 12.0 %
2450
39.2
1.80
7.47
7.47
7.47
0.35
0.80
± 12.0 %
2600
39.0
1.96
7.28
7.28
7.28
0.36
0.86
+ 12.0 %
3500
37.9
2.91
7.14
7.14
7.14
0.29
1.30
+ 13.1 %
5200
36.0
4.66
5.31
5.31
5.31
0.35
1.80
+ 13.1 %
5300
35.9
4.76
5.15
5.15
5.15
0.35
1.80
± 13.1 %
5500
35.6
4.96
4.66
4.66
4.66
0.45
1.80
± 13.1 %
5600
35.5
5.07
4.47
4.47
4 .47
0.50
1.80
± 13.1 %
5800
35.3
5.27
4.51
4 .51
4.51
0.50
1.80
± 13.1 %
c Frequency validity above 300 MHz of± 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to± 50 MHz. The
uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity
below 300 MHz is± 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency
validity can be extended to± 110 MHz.
F At frequencies below 3 GHz, the validity of tissue parameters (& and :: (. :
:i:.:- · ':. < ..
·.· :
:::
...e
ui
10·3
10·2
10-1
100
SAR [mW/cm3]
102
101
[!]
セ@
not compensated
compensated
Uncertainty of Linearity Assessment:± 0.6% (k=2)
Certificate No: EX3-3925_May16
Page 9 of 11
103
May 26, 2016
EX3DV4- SN:3925
Conve rsion Factor Assess ment
f = 1900 MHz,WGLS R22 (H_convF)
= 835 MHz,WGLS R9 (H_convF)
40
35·
..
..
30
·•.
:s
a,
2 0-
<{
:n
' 5
,o
'0:
05
00
--11,
l セ@
•
,o
15
20
. ·
.. L
Q. l I ,
40
:JS
30
25
.. I.
_ · -- ~ _.,.
セ@
15
'lO
zfmm]
.._ _
2!>
20
z[m m]
_!_.
J nal\"bC31
Deviation from Isotropy in Liquid
Error (cj,, S), f = 900 MHz
1.0
0.8
0.6
0.4
セ@ 0.2
-~ 0.0
0 ·0.2
135
+/~
180
セ@
225
270
315
-1.0
-0.8
-0.6
-0.4
-0.2
0.0
0.2
0.4
0.6
0.8
1.0
Uncertainty of Spherical Isotropy Assessment: ± 2.6% (k=2)
Certificate No: EX3-3925_May16
Page 10 of 11
• J
lO
セ@
•
.! •
3~
•
40
May 26, 2016
EX3DV4- SN:3925
DASY/EASY - Parameters of Probe: EX3DV4 - SN:3925
Other Probe Parameters
Triangular
Sensor Arrangement
92.2
Connector Angle (°)
Mechanical Surface Detection Mode
enabled
Optical Surface Detection Mode
disabled
Probe Overall Length
337mm
Probe Body Diameter
10mm
9mm
Tip Length
2.5mm
T ip Diameter
Probe Tip to Sensor X Calibration Point
1 mm
Probe Tip to Sensor Y Calibration Point
1 mm
Probe Tip to Sensor Z Calibration Point
1 mm
Recommended Measurement Distance from Surface
Certificate No: EX3-3925_May16
Page 11 of 11
1.4 mm

Download: TC700K Touch computer RF Exposure Info RF Exposure Appendix A-2 Zebra Technologies Corporation
Mirror Download [FCC.gov]TC700K Touch computer RF Exposure Info RF Exposure Appendix A-2 Zebra Technologies Corporation
Document ID3253770
Application IDe1MvloMtfRHhfoQq62Ptfw==
Document DescriptionRF Exposure Appendix A-2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeRF Exposure Info
Display FormatAdobe Acrobat PDF - pdf
Filesize438.32kB (5478939 bits)
Date Submitted2017-01-10 00:00:00
Date Available2017-01-11 00:00:00
Creation Date2017-12-20 16:21:50
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-12-20 16:21:50
Document TitleRF Exposure Appendix A-2
Document Author: Wan

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:46dcd0a0-a289-11f2-0000-02c7314339d4
Producer                        : GPL Ghostscript 9.18
Modify Date                     : 2017:07:16 21:21:27Z
Create Date                     : 2017:07:16 21:21:27Z
Creator Tool                    : UnknownApplication
Document ID                     : uuid:46dcd0a0-a289-11f2-0000-02c7314339d4
Format                          : application/pdf
Title                           : Untitled
EXIF Metadata provided by EXIF.tools

Facebook Twitter Google+ RSS © FCCID.io 2018