A026 Portable Speaker Users Manual 2016.1212 MMA3628 说明书 SHENZHEN AVWOO TECHNOLOGY CO., LTD

SIZE: 115x165mm
POWER SOURCE:
The unit has a built in Li-ion rechargeable battery, recharge it before use or when it is drained as follows:
1. Open the Rubber Cover on the top unit. (This cover is for water and dusts Ingress Protection, always make sure it is completely close.)
2. Connect the Micro USB Plug from the supplied USB Connection Cable to the Micro USB Port.
3. Connect the full sized USB Plug from the supplied USB Connection Cable to the USB Port on the supplied USB Charger to start
charging.
● During charging, the Red Indicator on the front of unit will illuminate. When finished, it will turn off.
● This AC/USB Adaptor is intended to be correctly orientated in a vertical or floor mount position.
● To save energy, unplug the AC/USB Adaptor from the wall outlet if you will not use it for an extended period of time.
● During charging, you can also play and listen music at the same time.
To supplied USB charger
Normal operation after pairing:
1. Power on the unit by pressing and holding the
Button on the bottom of the unit approximately 3 seconds. The unit will enter to BT
(Bluetooth) mode automatically. The Blue Indicator on the front of unit will illuminate and blink.
2. Wait a few seconds until the unit is automatically paired to the external BT Device. (The Blue Indicator will stop blinking).
3. After pairing is complete you may now play music and answer calls with your external BT Device.
AUX (in):
To listen from an external Audio Player such as a MP3 Player, Discman …etc.
1. Open the Rubber Cover on the top of unit. (This cover is for water and dusts Ingress Protection, always make sure it is completely
closed after open).
2. Connect one end of the supplied Audio Connection Cable to the AUX Out/Line Out/Phone Jack on the external Audio Player.
3. In power on mode, connect the other end of the cable to the AUX (in) Jack as the figure below. The unit will turn to AUX IN mode
automatically. The Green AUX (in) Indicator will illuminate.
FCC Statement
Portable Speaker
A026
User manual
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference,
and 2) this device must accept any interference
received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and
receiver.
--Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician
for help.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure
limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
To AUX Out/Line Out/Phone Jack
on the external Audio Player
To the Micro USB Port on the top of unit
Notes:
Your battery will last longer if you're following these simple guidelines for charging and storing.
A. Before first time use, charge it approximately 4 hours until the unit is fully charged.
B. Recharge and store the unit within the temperature range of 5°C~35°C (40°F~95°F).
C. Do not charge longer than 24 hours. Excessive charging or running the unit until battery fully drains will damage battery. Battery life will
be extended if you keep the battery fully charged.
D. Battery life naturally shortens slowly over time.
E. The rechargeable battery incorporated in this product is not user replaceable.
LOCATION OF CONTROLS:
①
②
③
④
⑤
To Line in Jack
4. Play the music on the connected Player as usual. (Make sure the volume level of the connected Audio Player is turned to high level.)
5. During playback:
● Press the
Button to mute the sound, press again to turn the sound back.
● Press and holding the
or
Buttons to adjust volume level as desired.
6. When no longer in use, press and hold the
Button to shut off the unit.
Note: If the Audio Connection Cable was plugged into the AUX (in) Jack, the Bluetooth function will auto cut. Unplug the Cable from the
⑥
⑦8
1. LED Indicator
2. Button
3. Built-in Microphone
4.
Button
5. Button
6. Power ON/OFF Button
7. Micro USB Port (For charge only)
8. AUX IN Jack
9. Rubber Cover (This cover is for water and dusts Ingress
Protection, always make sure it is completely closed)
AUX (in) Jack before use Bluetooth function.
TROUBLESHOOTING:
Can’t power on
Built in battery drained
Recharge the built-in battery as page 3.
No sound or sound
weak
Volume of the unit was set to minimum position
Increase the volume by press and hold the
Volume level of paired/connected device is in low level
Rise the volume level of the paired/connected device
Volume level too high
Reduce the volume level by press and holding the
Volume level of the connected/paired device too high
Reduce the volume level of the connected/paired device
The external BT Device had NOT paired to the unit
Pair the external BT Device to the unit as page 3.
The external BT device too far from the unit
Place the external BT device close to the unit
Sound distortion
BT not functioning
OPERATION:
BT (Bluetooth) pairing:
First time use or re-pairing the unit to a new BT Device, pair as follows:
1. Power on the unit by pressing and holding the
Button on the bottom of the unit approximately 3 seconds. The unit will enter to BT
(Bluetooth) mode automatically. The Blue Indicator on the front of unit will illuminate and blink.
2. Power on the external BT Device and enter to BT searching mode. Start pairing following the on screen instructions from the external
BT Device. After paired, the unit will sound a prompt tone and the Blue Indicator will stop blinking.
3. If pairing is complete you may now play music and answer calls with your external BT Device.
4. During playback:
● Press the
Button on the unit to pause, press again to resume normal playback.
● Press and holding the
or
Buttons to adjust volume level as desired.
● Press and release the
or
Buttons repeatedly to skip tracks.
5. If the unit is paired to a Cell Phone and a call is incoming during an active music session, press the
Button to pause the music
playback then speak to the built-in microphone to answer the call. When your call is complete, press the
Button to disconnect or
end the call and resume to music playback.
6. When finished listening, press and hold the
Button to shut off the unit.
Notes:
● When the external BT Device searched the unit, our model number “MMA3628” will appear on the display of external BT Device.
● If while pairing you are asked for a code please try "0000" or "1234".
GENERAL SPECIFICATION:
Power Source
BT Version
Built-in DC
3.7V, 2000 mAH(7.4WH) Li-ion rechargeable battery;
Recharge by DC
5V 1A through Micro USB Port
4.1
BT Effective range
Up to 32 feet in open area
Audio Power
5 Watts Per channel (Total 10 Watts RMS)
Impedance of speaker
2 x 6 W; 4 ohm
ACCESSORIES:
1 x User's Manual
1 x USB Connection Cable (For charge only)
1 x Audio Connection Cables with 3.5mm Plugs
1 x AC/USB Adapter (Input: AC 100-240V~; 50/60Hz, 0.2A Max; Output: DC
5V; 1000mA)
SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Button
Button