RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD

SHENZHEN RUIHE TECHNOLOGY CO.,LTD Vr all-in-one

FCC ID Filing: 2AKNBRT-V03
Purchase on Amazon: Vr all-in-one

Trouble Viewing? See the or view the HTML Version or PDF in frame
Page 1 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 2 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 3 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 4 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 5 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 6 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 7 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 8 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 9 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 10 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 11 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 12 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 13 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 14 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 15 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 16 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 17 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 18 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 19 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 20 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 21 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 22 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 23 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 24 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 25 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 26 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 27 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 28 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 29 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 30 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 31 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 32 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 33 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 34 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 35 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 36 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 37 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 38 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 39 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 40 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 41 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 42 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 43 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 44 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 45 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 46 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 47 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 48 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 49 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 50 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Page 51 of RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
FCC TEST REPORT
For
SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Vr all-in-one
TEST Model No.: RT-V03
Prepared for
Address
SHENZHEN RUIHE TECHNOLOGY CO.,LTD
3/F B1 Building, Mingjun Industrial park, Huaning Rd, Bao’an Area,
Shenzhen, China
Prepared by
Address
Tel
Fax
Web
Mail
Shenzhen LCS Compliance Testing Laboratory Ltd.
1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an
District, Shenzhen, Guangdong, China
(+86)755-82591330
(+86)755-82591332
www.LCS-cert.com
[email protected]
Date of receipt of test sample
Number of tested samples
Serial number
Date of Test
Date of Report
December 01, 2016
Prototype
December 01, 2016~December 23, 2016
December 23, 2016
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 1 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
FCC TEST REPORT
FCC CFR 47 PART 15 C(15.247): 2015
Report Reference No. ................. : LCS1612223161E
Date of Issue ................................... : December 23, 2016
Testing Laboratory Name............. : Shenzhen LCS Compliance Testing Laboratory Ltd.
Address ........................................... : 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue,
Bao'an District, Shenzhen, Guangdong, China
Testing Location/ Procedure ........... : Full application of Harmonised standards ■
Partial application of Harmonised standards □
Other standard testing method □
Applicant’s Name .......................... : SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Address ........................................... : 3/F B1 Building, Mingjun Industrial park, Huaning Rd, Bao’an Area,
Shenzhen, China
Test Specification
Standard .......................................... : FCC CFR 47 PART 15 C(15.247): 2015
Test Report Form No. ................... : LCSEMC-1.0
TRF Originator ................................ : Shenzhen LCS Compliance Testing Laboratory Ltd.
Master TRF ..................................... : Dated 2011-03
Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the
Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the
material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not
assume liability for damages resulting from the reader's interpretation of the reproduced material due to its
placement and context.
EUT Description. ........................... : Vr all-in-one
Trade Mark ...................................... : REMAX
Model/ Type reference .................... : RT-V03
Ratings ............................................ : DC 3.7V by battery(3200mAh)
Recharged by DC 5V/2A
Result ............................................ : Positive
Compiled by:
Supervised by:
Approved by:
Dick Su/ File administrators
Glin Lu/ Technique principal
Gavin Liang/ Manager
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 2 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
FCC -- TEST REPORT
Test Report No. :
LCS1612223161E
December 23, 2016
Date of issue
EUT........................................
Type / Model...........................
: Vr all-in-one
: RT-V03
Applicant...............................
Address..................................
: SHENZHEN RUIHE TECHNOLOGY CO.,LTD
: 3/F B1 Building, Mingjun Industrial park, Huaning Rd, Bao’an Area,
Shenzhen, China
: /
: /
Telephone..............................
Fax.........................................
Manufacturer........................
Address...................................
Telephone..............................
Fax.........................................
Factory..................................
Address..................................
Telephone..............................
Fax.........................................
Test Result
: SHENZHEN RUIHE TECHNOLOGY CO.,LTD
: 3/F B1 Building, Mingjun Industrial park, Huaning Rd, Bao’an Area,
Shenzhen, China
: /
: /
: SHENZHEN RUIHE TECHNOLOGY CO.,LTD
: 3/F B1 Building, Mingjun Industrial park, Huaning Rd, Bao’an Area,
Shenzhen, China
: /
: /
Positive
The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test
laboratory.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 3 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
Revision History
Revision
Issue Date
Revisions
Revised By
00
2016-12-23
Initial Issue
Gavin Liang
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
TABLE OF CONTENTS
1. GENERAL INFORMATION ................................................................................................................................... 6
1.1. DESCRIPTION OF DEVICE (EUT) ........................................................................................................................ 6
1.2. HOST SYSTEM CONFIGURATION LIST AND DETAILS .......................................................................................... 6
1.3. EXTERNAL I/O CABLE ......................................................................................................................................... 6
1.4. DESCRIPTION OF TEST FACILITY ........................................................................................................................ 7
1.5. STATEMENT OF THE MEASUREMENT UNCERTAINTY .......................................................................................... 7
1.6. MEASUREMENT UNCERTAINTY ........................................................................................................................... 8
1.7. DESCRIPTION OF TEST MODES .......................................................................................................................... 8
2. TEST METHODOLOGY ......................................................................................................................................... 9
2.1. EUT CONFIGURATION ........................................................................................................................................ 9
2.2. EUT EXERCISE ................................................................................................................................................... 9
2.3. GENERAL TEST PROCEDURES ........................................................................................................................... 9
3. SYSTEM TEST CONFIGURATION .................................................................................................................... 10
3.1. JUSTIFICATION .................................................................................................................................................. 10
3.2. EUT EXERCISE SOFTWARE .............................................................................................................................. 10
3.3. SPECIAL ACCESSORIES .................................................................................................................................... 10
3.4. BLOCK DIAGRAM/SCHEMATICS......................................................................................................................... 10
3.5. EQUIPMENT MODIFICATIONS ............................................................................................................................ 10
3.6. TEST SETUP ...................................................................................................................................................... 10
4. SUMMARY OF TEST RESULTS ........................................................................................................................ 11
5. TEST RESULT ....................................................................................................................................................... 12
5.1. ON TIME AND DUTY CYCLE .............................................................................................................................. 12
5.2. MAXIMUM CONDUCTED OUTPUT POWER MEASUREMENT............................................................................... 14
5.3. POWER SPECTRAL DENSITY MEASUREMENT .................................................................................................. 16
5.4. 6 DB SPECTRUM BANDWIDTH MEASUREMENT ................................................................................................ 20
5.5. RADIATED EMISSIONS MEASUREMENT............................................................................................................. 24
5.6. CONDUCTED SPURIOUS EMISSIONS AND BAND EDGES TEST ......................................................................... 34
5.7. AC POWER LINE CONDUCTED EMISSIONS ........................................................................................................ 41
5.8. BAND-EDGE MEASUREMENTS FOR RADIATED EMISSIONS ................................................................................ 44
5.9. ANTENNA REQUIREMENTS ................................................................................................................................ 49
6. LIST OF MEASURING EQUIPMENTS .............................................................................................................. 51
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 5 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
1. GENERAL INFORMATION
1.1. Description of Device (EUT)
EUT
: Vr all-in-one
Test Model
: RT-V03
Hardware version
: v509_MB_V(1.2)
Software version
: Nibiru 2.00.001/vr0079/(20161109103756)
Power Supply
: DC 3.7V by battery(3200mAh)
Recharged by DC 5V/2A
WLAN
: Supported 802.11b/802.11g/802.11n
WLAN FCC Operation Frequency : IEEE 802.11b:2412-2462MHz
IEEE 802.11g:2412-2462MHz
IEEE 802.11n HT20:2412-2462MHz
WLAN Channel Number
: 11 Channels for WIFI 20MHz Bandwidth(802.11b/g/n-HT20)
WLAN Modulation Technology
: IEEE 802.11b: DSSS(CCK,DQPSK,DBPSK)
IEEE 802.11g: OFDM(64QAM, 16QAM, QPSK, BPSK)
IEEE 802.11n: OFDM (64QAM, 16QAM,QPSK,BPSK)
Bluetooth
: Supported BT 4.0+EDR
Bluetooth Operation frequency
: 2402MHz-2480MHz
Bluetooth Modulation Type
: GFSK,π/4DQPSK, 8DPSK
Bluetooth Channel Number
: 79 Channels for Bluetooth 4.0(DSS); 40 Channels for Bluetooth 4.0(DTS)
Antenna Type
: Internal Antenna
Antenna Gain
: 1.0 dBi(max.) For WIFI/BT
Extreme temp. Tolerance
: -30°C to +50°C
Extreme vol. Limits
: 3.40VDC to 4.20VDC (nominal: 3.70VDC)
1.2. Host System Configuration List and Details
Manufacturer
Description
Model
Serial Number
Certificate
Lenovo
PC
AC/DC
ADAPTER
B470
--
DOC
ADP-90DDB
--
DOC
Lenovo
1.3. External I/O Cable
I/O Port Description
Quantity
Cable
Earphone Jack
N/A
Mini USB Port
N/A
A USB Port
N/A
TF Card Slot
N/A
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 6 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
1.4. Description of Test Facility
CNAS Registration Number. is L4595.
FCC Registration Number. is 899208.
Industry Canada Registration Number. is 9642A-1.
VCCI Registration Number. is C-4260 and R-3804.
ESMD Registration Number. is ARCB0108.
UL Registration Number. is 100571-492.
TUV SUD Registration Number. is SCN1081.
TUV RH Registration Number. is UA 50296516-001
The 3m-Semi anechoic test site fulfils CISPR 16-1-4 according to ANSI C63.4:2014 and CISPR
16-1-4:2010 SVSWR requirement for radiated emission above 1GHz.
1.5. Statement of the Measurement Uncertainty
The data and results referenced in this document are true and accurate. The reader is cautioned that
there may be errors within the calibration limits of the equipment and facilities. The measurement
uncertainty was calculated for all measurements listed in this test report acc. To CISPR 16 – 4
“Specification for radio disturbance and immunity measuring apparatus and methods – Part 4: Uncertainty
in EMC Measurements” and is documented in the LCS quality system acc. To DIN EN ISO/IEC 17025.
Furthermore, component and process variability of devices similar to that tested may result in additional
deviation. The manufacturer has the sole responsibility of continued compliance of the device.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 7 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
1.6. Measurement Uncertainty
Test Item
Radiation Uncertainty
Frequency Range
Uncertainty
Note
9KHz~30MHz
±3.10dB
(1)
30MHz~200MHz
±2.96dB
(1)
200MHz~1000MHz
±3.10dB
(1)
1GHz~26.5GHz
±3.80dB
(1)
26.5GHz~40GHz
±3.90dB
(1)
150kHz~30MHz
±1.63dB
(1)
30MHz~300MHz
±1.60dB
(1)
Conduction Uncertainty :
Power disturbance
(1). This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence
level using a coverage factor of k=2.
1.7. Description of Test Modes
The EUT has been tested under operating condition.
This test was performed with EUT in X, Y, Z position and the worst case was found when EUT in X
position.
Worst-case mode and channel used for 150 kHz-30 MHz power line conducted emissions was the mode
and channel with the highest output power, which was determined to be 802.11b mode (High Channel).
Worst-case mode and channel used for 9kHz-1000 MHz radiated emissions was the mode and channel
with the highest output power, that was determined to be 802.11b mode(High Channel).
Pre-test AC conducted emission at both power adapter and charge from PC mode, recorded worst case.
Pre-test AC conducted emission at both voltage AC 120V/60Hz and AC 240V/50Hz, recorded worst case.
Worst-Case data rates were utilized from preliminary testing of the Chipset, worst-case data
rates used during the testing are as follows:
802.11b Mode: 1 Mbps, DSSS.
802.11g Mode: 6 Mbps, OFDM.
802.11n Mode HT20: MCS0, OFDM.
Channel List & Frequency
IEEE 802.11b/g/n HT20
Frequency Band
2412~2462MHz
Channel No.
Frequency(MHz)
2412
2417
2422
2427
2432
2437
Channel No.
10
11
--
Frequency(MHz)
2442
2447
2452
2457
2462
--
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 8 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
2. TEST METHODOLOGY
All measurements contained in this report were conducted with ANSI C63.10-2013, American National
Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices.
The radiated testing was performed at an antenna-to-EUT distance of 3 meters. All radiated and
conducted emissions measurement was performed at Shenzhen LCS Compliance Testing Laboratory Ltd.
2.1. EUT Configuration
The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions
requirement and operating in a manner that intends to maximize its emission characteristics in a
continuous normal application.
2.2. EUT Exercise
The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the
measurements.
According to FCC’s request, Test Procedure KDB558074 D01 DTS Meas. Guidance v03r05 and KDB
662911 are required to be used for this kind of FCC 15.247 digital modulation device.
According to its specifications, the EUT must comply with the requirements of the Section 15.203, 15.205,
15.207, 15.209 and 15.247 under the FCC Rules Part 15 Subpart C.
2.3. General Test Procedures
2.3.1 Conducted Emissions
The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in
Section 6.2.1 of ANSI C63.10-2013 Conducted emissions from the EUT measured in the frequency range
between 0.15 MHz and 30MHz using Quasi-peak and average detector modes.
2.3.2 Radiated Emissions
The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360
degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving
antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be
maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find
out the maximum emissions, exploratory radiated emission measurements were made according to the
requirements in Section 6.3 of ANSI C63.10-2013
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 9 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
3. SYSTEM TEST CONFIGURATION
3.1. Justification
The system was configured for testing in a continuous transmits condition. The duty cycle is 100% and the
average correction factor is 0.
3.2. EUT Exercise Software
N/A
3.3. Special Accessories
N/A
3.4. Block Diagram/Schematics
Please refer to the related document
3.5. Equipment Modifications
Shenzhen LCS Compliance Testing Laboratory Ltd. has not done any modification on the EUT.
3.6. Test Setup
Please refer to the test setup photo.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 10 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
4. SUMMARY OF TEST RESULTS
Applied Standard: FCC Part 15 Subpart C
FCC Rules
Description of Test
Result
Duty Cycle
Compliant
§15.247(b)
Maximum Conducted Output Power
Compliant
§15.247(e)
Power Spectral Density
Compliant
§15.247(a)(2)
6dB Bandwidth
Compliant
§15.247(a)
Occupied Bandwidth
Compliant
§15.209, §15.247(d)
Radiated and Conducted Spurious Emissions
Compliant
§15.205
Emissions at Restricted Band
Compliant
§15.207(a)
Conducted Emissions
Compliant
§15.203
Antenna Requirements
Compliant
§15.247(i)§2.1093
RF Exposure
Compliant
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 11 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5. TEST RESULT
5.1. On Time and Duty Cycle
5.1.1. Standard Applicable
None; for reporting purpose only.
5.1.2. Measuring Instruments and Setting
Please refer to section 6 of equipment list in this report. The following table is the setting of the spectrum
analyzer.
5.1.3. Test Procedures
1. Set the center frequency of the spectrum analyzer to the transmitting frequency;
2. Set the span=0MHz, RBW=8MHz, VBW=50MHz, Sweep time=5ms;
3. Detector = peak;
4. Trace mode = Single hold.
5.1.4. Test Setup Layout
5.1.5. EUT Operation during Test
The EUT was programmed to be in continuously transmitting mode.
5.1.6. Test result
IEEE 802.11b
On Time
(ms)
8.414
IEEE 802.11g
1.395
1.437
97.08%
0.13
0.717
IEEE 802.11n
HT20
1.307
1.348
97.00%
0.13
0.765
Mode
99.53%
Duty Cycle
Correction Factor
(dB)
0.02
1/B
Minimum VBW
(KHz)
0.119
Period
(ms)
Duty Cycle x
(Linear)
Duty Cycle
(%)
8.454
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 12 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
On Time and Duty Cycle
IEEE 802.11b
IEEE 802.11g
IEEE 802.11n HT20
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 13 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.2. Maximum Conducted Output Power Measurement
5.2.1. Standard Applicable
According to §15.247(b): For systems using digital modulation in the 2400-2483.5 MHz and 5725-5850
MHz band, the limit for maximum peak conducted output power is 30dBm. The limited has to be reduced
by the amount in dB that the gain of the antenna exceeds 6dBi. In case of point-to-point operation, the
limit has to be reduced by 1dB for every 3dB that the directional gain of the antenna exceeds 6dBi.
Systems operating in the 5725-5850 MHz band that are used exclusively for fixed, point-to-point
operations may employ transmitting antennas with directional gain greater than 6dBi without any
corresponding reduction in transmitter peak output power.
5.2.2. Measuring Instruments and Setting
Please refer to section 6 of equipment list in this report. The following table is the setting of the power
meter.
5.2.3. Test Procedures
According to KDB558074 D01 DTS Measurement Guidance Section 9.1 Maximum peak conducted output
power, 9.1.2 The maximum peak conducted output power may be measured using a broadband peak RF
power meter. The power meter shall have a video bandwidth that is greater than or equal to the DTS
bandwidth and shall utilize a fast-responding diode detector.
5.2.4. Test Setup Layout
5.2.5. EUT Operation during Test
The EUT was programmed to be in continuously transmitting mode.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 14 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.2.6. Test Result of Maximum Conducted Output Power
Temperature
25℃
Humidity
60%
Test Engineer
Dick
Configurations
IEEE 802.11b/g/n
Test Mode
IEEE 802.11b
IEEE 802.11g
IEEE 802.11n
HT20
Channel
Frequency
(MHz)
11
11
11
2412
2437
2462
2412
2437
2462
2412
2437
2462
Measured Peak Output
Power
(dBm)
8.16
8.07
8.31
7.34
7.40
7.32
7.24
7.14
7.27
Limits
(dBm)
Verdict
30
PASS
30
PASS
30
PASS
Remark:
1. Measured output power at difference data rate for each mode and recorded worst case for each mode.
2. Test results including cable loss;
3. Worst case data at 1Mbps at IEEE 802.11b; 6Mbps at IEEE 802.11g; 6.5Mbps at IEEE 802.11n HT20.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 15 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.3. Power Spectral Density Measurement
5.3.1. Standard Applicable
According to §15.247(e): For digitally modulated systems, the power spectral density conducted from the
intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time
interval of continuous transmission.
5.3.2. Measuring Instruments and Setting
Please refer to section 6 of equipment list in this report. The following table is the setting of Spectrum
Analyzer.
5.3.3. Test Procedures
1. Use this procedure when the maximum peak conducted output power in the fundamental emission is
used to demonstrate compliance.
2. The power was monitored at the coupler port with a Spectrum Analyzer. The power level was set to the
maximum level.
3. Set the RBW = 3 kHz.
4. Set the VBW ≥ 3*RBW
5. Set the span to 1.5 times the DTS channel bandwidth.
6. Detector = peak.
7. Sweep time = auto couple.
8. Trace mode = max hold.
9. Allow trace to fully stabilize.
10. Use the peak marker function to determine the maximum power level.
11. If measured value exceeds limit, reduce RBW (no less than 3 kHz) and repeat.
12. The resulting peak PSD level must be 8 dBm.
5.3.4. Test Setup Layout
5.3.5. EUT Operation during Test
The EUT was programmed to be in continuously transmitting mode.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 16 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.3.6. Test Result of Power Spectral Density
Temperature
25℃
Humidity
60%
Test Engineer
Dick
Configurations
IEEE 802.11b/g/n
Test Mode
IEEE 802.11b
IEEE 802.11g
IEEE 802.11n
HT20
Channel
Frequency
(MHz)
11
11
11
2412
2437
2462
2412
2437
2462
2412
2437
2462
Measured Peak Power
Spectral Density
(dBm/100KHz)
-5.987
-5.815
-5.516
-10.241
-10.312
-11.136
-11.682
-11.146
-10.703
Limits
(dBm/3KHz)
Verdict
PASS
PASS
PASS
Remark:
1. Measured output power at difference data rate for each mode and recorded woest case for each mode.
2. Test results including cable loss;
3. Worst case data at 1Mbps at IEEE 802.11b; 6Mbps at IEEE 802.11g; 6.5Mbps at IEEE 802.11n HT20;
4. please refer to following plots;
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 17 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
Peak Power Spectrum Density
IEEE 802.11b
IEEE 802.11g
Channel 1 / 2412 MHz
Channel 1 / 2412 MHz
Channel 6 / 2437 MHz
Channel 6 / 2437 MHz
Channel 11 / 2462 MHz
Channel 11 / 2462 MHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 18 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
Peak Power Spectrum Density
IEEE 802.11n HT20
IEEE 802.11n HT20
Channel 1 / 2412 MHz
Channel 6 / 2437 MHz
Channel 11 / 2462 MHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 19 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.4. 6 dB Spectrum Bandwidth Measurement
5.4.1. Standard Applicable
According to §15.247(a)(2): For digital modulation systems, the minimum 6 dB bandwidth shall be at least
500 kHz.
5.4.2. Measuring Instruments and Setting
Please refer to section 6 of equipment list in this report. The following table is the setting of the Spectrum
Analyzer.
Spectrum Parameter
Attenuation
Span Frequency
Detector
Trace
Sweep Time
Setting
Auto
> RBW
Peak
Max Hold
100ms
5.4.3. Test Procedures
1. The transmitter output (antenna port) was connected to the spectrum analyzer in peak hold mode.
2. The resolution bandwidth and the video bandwidth were set according to KDB558074.
3. Measured the spectrum width with power higher than 6dB below carrier.
5.4.4. Test Setup Layout
5.4.5. EUT Operation during Test
The EUT was programmed to be in continuously transmitting mode.
5.4.6. Test Result of 6dB Spectrum Bandwidth
Temperature
25℃
Humidity
60%
Test Engineer
Dick
Configurations
IEEE 802.11b/g/n
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 20 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
Test Mode
IEEE 802.11b
IEEE 802.11g
IEEE 802.11n
HT20
Channel
11
11
11
Frequency
(MHz)
2412
2437
2462
2412
2437
2462
2412
2437
2462
FCC ID: 2AKNBRT-V03
6dB Bandwidth
(MHz)
9.058
8.587
9.075
15.07
15.14
15.14
15.13
15.14
15.11
Report No.: LCS1612223161E
Limits
(MHz)
Verdict
0.500
PASS
0.500
PASS
0.500
PASS
Remark:
1. Measured output power at difference data rate for each mode and recorded worst case for each mode.
2. Test results including cable loss;
3. Worst case data at 1Mbps at IEEE 802.11b; 6Mbps at IEEE 802.11g; 6.5Mbps at IEEE 802.11n HT20;
4. please refer to following plots;
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 21 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
6 dB Bandwidth
IEEE 802.11b
IEEE 802.11g
Channel 1 / 2412 MHz
Channel 1 / 2412 MHz
Channel 6 / 2437 MHz
Channel 6 / 2437 MHz
Channel 11 / 2462 MHz
Channel 11 / 2462 MHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 22 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
6 dB Bandwidth
IEEE 802.11n HT20
--
Channel 1 / 2412 MHz
--
--
Channel 6 / 2437 MHz
--
--
Channel 11 / 2462 MHz
--
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 23 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.5. Radiated Emissions Measurement
5.5.1. Standard Applicable
15.205 (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any
of the frequency bands listed below:
MHz
0.090-0.110
\1\ 0.495-0.505
2.1735-2.1905
4.125-4.128
4.17725-4.17775
4.20725-4.20775
6.215-6.218
6.26775-6.26825
6.31175-6.31225
8.291-8.294
8.362-8.366
8.37625-8.38675
8.41425-8.41475
12.29-12.293.
12.51975-12.52025
12.57675-12.57725
13.36-13.41
MHz
MHz
16.42-16.423
16.69475-16.69525
16.80425-16.80475
25.5-25.67
37.5-38.25
73-74.6
74.8-75.2
108-121.94
123-138
149.9-150.05
156.52475-156.52525
156.7-156.9
162.0125-167.17
167.72-173.2
240-285
322-335.4
399.9-410
608-614
960-1240
1300-1427
1435-1626.5
1645.5-1646.5
1660-1710
1718.8-1722.2
2200-2300
2310-2390
2483.5-2500
2690-2900
3260-3267
3332-3339
3345.8-3358
3600-4400
GHz
4.5-5.15
5.35-5.46
7.25-7.75
8.025-8.5
9.0-9.2
9.3-9.5
10.6-12.7
13.25-13.4
14.47-14.5
15.35-16.2
17.7-21.4
22.01-23.12
23.6-24.0
31.2-31.8
36.43-36.5
(\2\)
\1\ Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz.
\2\ Above 38.6
According to §15.247 (d): 20dBc in any 100 kHz bandwidth outside the operating frequency band. In case
the emission fall within the restricted band specified on 15.205(a), then the 15.209(a) limit in the table
below has to be followed.
Frequencies
(MHz)
0.009~0.490
0.490~1.705
1.705~30.0
30~88
88~216
216~960
Above 960
Field Strength
(microvolts/meter)
2400/F(KHz)
24000/F(KHz)
30
100
150
200
500
Measurement Distance
(meters)
300
30
30
5.5.2. Measuring Instruments and Setting
Please refer to section 6 of equipment list in this report. The following table is the setting of spectrum
analyzer and receiver.
Spectrum Parameter
Attenuation
Start Frequency
Stop Frequency
RB / VB (Emission in restricted band)
RB / VB (Emission in non-restricted band)
Receiver Parameter
Attenuation
Start ~ Stop Frequency
Start ~ Stop Frequency
Start ~ Stop Frequency
Setting
Auto
1000 MHz
10th carrier harmonic
1MHz / 1MHz for Peak, 1 MHz / 1/B kHz for Average
1MHz / 1MHz for Peak, 1 MHz / 1/B kHz for Average
Setting
Auto
9kHz~150kHz / RB/VB 200Hz/1KHz for QP/AVG
150kHz~30MHz / RB/VB 9kHz/30KHz for QP/AVG
30MHz~1000MHz / RB/VB 120kHz/1MHz for QP
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 24 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.5.3. Test Procedures
1) Sequence of testing 9 kHz to 30 MHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described by
manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 0.8 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions.
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna height is 1.5 meter.
--- At each turntable position the analyzer sweeps with peak detection to find the maximum of all
emissions
Final measurement:
--- Identified emissions during the premeasurement the software maximizes by rotating the turntable
position (0° to 360°) and by rotating the elevation axes (0° to 360°).
--- The final measurement will be done in the position (turntable and elevation) causing the highest
emissions with QPK detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, correction factor, margin to
the limit and limit will be recorded. Also a plot with the graph of the premeasurement and the limit will be
stored.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 25 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
2) Sequence of testing 30 MHz to 1 GHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described by
manufacturer.
--- If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground plane.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height changes from 1 to 3 meter.
--- At each turntable position, antenna polarization and height the analyzer sweeps three times in peak to
find the maximum of all emissions.
Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software maximize
the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4 meter.
--- The final measurement will be done with QP detector with an EMI receiver.
--- The final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization, turntable
angle, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of the
premeasurement with marked maximum final measurements and the limit will be stored.
3) Sequence of testing 1 GHz to 18 GHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described by
manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna is polarized vertical and horizontal.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 26 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
--- The antenna height scan range is 1 meter to 2.5 meter.
--- At each turntable position and antenna polarization the analyzer sweeps with peak detection to find the
maximum of all emissions.
Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software maximize
the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4 meter. This
procedure is repeated for both antenna polarizations.
--- The final measurement will be done in the position (turntable, EUT-table and antenna polarization)
causing the highest emissions with Peak and Average detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, EUT-table position, antenna
polarization, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of
the premeasurement with marked maximum final measurements and the limit will be stored.
4) Sequence of testing above 18 GHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described by
manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 1 meter.
--- The EUT was set into operation.
Premeasurement:
--- The antenna is moved spherical over the EUT in different polarizations of the antenna.
Final measurement:
--- The final measurement will be performed at the position and antenna orientation for all detected
emissions that were found during the premeasurements with Peak and Average detector.
--- The final levels, frequency, measuring time, bandwidth, correction factor, margin to the limit and limit
will be recorded. Also a plot with the graph of the premeasurement and the limit will be stored.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 27 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.5.4. Test Setup Layout
For radiated emissions below 30MHz
Above 10 GHz shall be extrapolated to the specified distance using an extrapolation factor of 20
dB/decade form 3m to 1.5m.
Distance extrapolation factor = 20 log (specific distanc [3m] / test distance [1.5m]) (dB);
Limit line = specific limits (dBuV) + distance extrapolation factor [6 dB].
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 28 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.5.5. EUT Operation during Test
The EUT was programmed to be in continuously transmitting mode.
5.5.6. Results of Radiated Emissions (9 kHz~30MHz)
Temperature
25℃
Humidity
60%
Test Engineer
Dick
Configurations
802.11b/g/n
Freq.
(MHz)
Level
(dBuV)
Over Limit
(dB)
Over Limit
(dBuV)
Remark
See Note
Note:
The amplitude of spurious emissions which are attenuated by more than 20 dB below the permissible
value has no need to be reported.
Distance extrapolation factor = 40 log (specific distance / test distance) (dB);
Limit line = specific limits (dBuV) + distance extrapolation factor.
5.5.7. Results of Radiated Emissions (30MHz~1GHz)
Temperature
25℃
Humidity
60%
Test Engineer
Dick
Configurations
IEEE 802.11b (High CH)
Test result for 802.11b (High Channel)
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 29 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
Note:
Pre-scan all modes and recorded the worst case results in this report (IEEE 802.11b (High Channel)).
Emission level (dBuV/m) = 20 log Emission level (uV/m).
Corrected Reading: Antenna Factor + Cable Loss + Read Level - Preamp Factor = Level.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 30 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.5.8. Results for Radiated Emissions (Above 1GHz)
IEEE 802.11b
Channel 1 / 2412 MHz
60.54
Ant.
Fac.
dB/m
33.06
Pre.
Fac.
dB
35.04
Cab.
Loss
dB
3.94
4824.00
42.06
33.06
35.04
4824.00
60.53
33.06
4824.00
42.29
33.06
Freq.
MHz
Reading
dBuv
4824.00
Measured
dBuv/m
Limit
dBuv/m
Margin
dB
Remark
Pol.
62.50
74.00
-11.50
Peak
Horizontal
3.94
44.02
54.00
-9.98
Average
Horizontal
35.04
3.94
62.49
74.00
-11.51
Peak
Vertical
35.04
3.94
44.25
54.00
-9.75
Average
Vertical
Pre.
Fac.
dB
35.15
Cab.
Loss
dB
3.96
Measured
dBuv/m
Limit
dBuv/m
Margin
dB
Remark
Pol.
65.18
74.00
-8.82
Peak
Horizontal
Channel 6 / 2437 MHz
Freq.
MHz
Reading
dBuv
4874.00
63.21
Ant.
Fac.
dB/m
33.16
4874.00
43.48
33.16
35.15
3.96
45.45
54.00
-8.55
Average
Horizontal
4874.00
59.86
33.16
35.15
3.96
61.83
74.00
-12.17
Peak
Vertical
4874.00
41.84
33.16
35.15
3.96
43.81
54.00
-10.19
Average
Vertical
Pre.
Fac.
dB
35.14
Cab.
Loss
dB
3.98
Measured
dBuv/m
Limit
dBuv/m
Margin
dB
Remark
Pol.
63.13
74.00
-10.87
Peak
Horizontal
Channel 11 / 2462 MHz
Freq.
MHz
Reading
dBuv
4924.00
61.03
Ant.
Fac.
dB/m
33.26
4924.00
42.88
33.26
35.14
3.98
44.98
54.00
-9.02
Average
Horizontal
4924.00
62.09
33.26
35.14
3.98
64.19
74.00
-9.81
Peak
Vertical
4924.00
41.10
33.26
35.14
3.98
43.20
54.00
-10.80
Average
Vertical
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 31 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
IEEE 802.11g
Channel 1 / 2412 MHz
60.23
Ant.
Fac.
dB/m
33.06
Pre.
Fac.
dB
35.04
Cab.
Loss
dB
3.94
4824.00
43.74
33.06
35.04
4824.00
58.08
33.06
4824.00
41.18
33.06
Freq.
MHz
Reading
dBuv
4824.00
Measured
dBuv/m
Limit
dBuv/m
Margin
dB
Remark
Pol.
62.19
74.00
-11.81
Peak
Horizontal
3.94
45.70
54.00
-8.30
Average
Horizontal
35.04
3.94
60.04
74.00
-13.96
Peak
Vertical
35.04
3.94
43.14
54.00
-10.86
Average
Vertical
Pre.
Fac.
dB
35.15
Cab.
Loss
dB
3.96
Measured
dBuv/m
Limit
dBuv/m
Margin
dB
Remark
Pol.
60.82
74.00
-13.18
Peak
Horizontal
Channel 6 / 2437 MHz
Freq.
MHz
Reading
dBuv
4874.00
58.85
Ant.
Fac.
dB/m
33.16
4874.00
42.56
33.16
35.15
3.96
44.53
54.00
-9.47
Average
Horizontal
4874.00
58.34
33.16
35.15
3.96
60.31
74.00
-13.69
Peak
Vertical
4874.00
40.50
33.16
35.15
3.96
42.47
54.00
-11.53
Average
Vertical
Pre.
Fac.
dB
35.14
Cab.
Loss
dB
3.98
Measured
dBuv/m
Limit
dBuv/m
Margin
dB
Remark
Pol.
63.40
74.00
-10.60
Peak
Horizontal
Channel 11 / 2462 MHz
Freq.
MHz
Reading
dBuv
4924.00
61.30
Ant.
Fac.
dB/m
33.26
4924.00
42.44
33.26
35.14
3.98
44.54
54.00
-9.46
Average
Horizontal
4924.00
59.51
33.26
35.14
3.98
61.61
74.00
-12.39
Peak
Vertical
4924.00
40.59
33.26
35.14
3.98
42.69
54.00
-11.31
Average
Vertical
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 32 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
IEEE802.11 n HT20
Channel 1 / 2412 MHz
63.22
Ant.
Fac.
dB/m
33.06
Pre.
Fac.
dB
35.04
Cab.
Loss
dB
3.94
4824.00
47.69
33.06
35.04
4824.00
62.54
33.06
4824.00
46.64
33.06
Freq.
MHz
Reading
dBuv
4824.00
Measured
dBuv/m
Limit
dBuv/m
Margin
dB
Remark
Pol.
65.18
74.00
-8.82
Peak
Horizontal
3.94
49.65
54.00
-4.35
Average
Horizontal
35.04
3.94
64.50
74.00
-9.50
Peak
Vertical
35.04
3.94
48.60
54.00
-5.40
Average
Vertical
Pre.
Fac.
dB
35.15
Cab.
Loss
dB
3.96
Measured
dBuv/m
Limit
dBuv/m
Margin
dB
Remark
Pol.
66.76
74.00
-7.24
Peak
Horizontal
Channel 6 / 2437 MHz
Freq.
MHz
Reading
dBuv
4874.00
64.79
Ant.
Fac.
dB/m
33.16
4874.00
46.70
33.16
35.15
3.96
48.67
54.00
-5.33
Average
Horizontal
4874.00
60.96
33.16
35.15
3.96
62.93
74.00
-11.07
Peak
Vertical
4874.00
45.38
33.16
35.15
3.96
47.35
54.00
-6.65
Average
Vertical
Pre.
Fac.
dB
35.14
Cab.
Loss
dB
3.98
Measured
dBuv/m
Limit
dBuv/m
Margin
dB
Remark
Pol.
68.44
74.00
-5.56
Peak
Horizontal
Channel 11 / 2462 MHz
Freq.
MHz
Reading
dBuv
4924.00
66.34
Ant.
Fac.
dB/m
33.26
4924.00
47.50
33.26
35.14
3.98
49.60
54.00
-4.40
Average
Horizontal
4924.00
63.41
33.26
35.14
3.98
65.51
74.00
-8.49
Peak
Vertical
4924.00
45.28
33.26
35.14
3.98
47.38
54.00
-6.62
Average
Vertical
Notes:
1. Measuring frequencies from 9k~10th harmonic or 26.5GHz (which is less), No emission found between
lowest internal used/generated frequency to 30MHz.
2. Radiated emissions measured in frequency range from 9k~10th harmonic or 26.5GHz (which is less)
were made with an instrument using Peak detector mode.
3. Data of measurement within this frequency range shown “---” in the table above means the reading of
emissions are attenuated more than 20dB below the permissible limits or the field strength is too small
to be measured.
4. Worst case data at 1Mbps at IEEE 802.11b; 6Mbps at IEEE 802.11g; 6.5Mbps at IEEE 802.11n HT20.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 33 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.6. Conducted Spurious Emissions and Band Edges Test
5.6.1. Standard Applicable
According to §15.247 (d): In any 100 kHz bandwidth outside the frequency band in which the spread
spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is
produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the
band that contains the highest level of the desired power, based on either an RF conducted or a radiated
measurement. Attenuation below the general limits specified in Section 15.209(a) is not required. In
addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also
comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)).
5.6.2. Measuring Instruments and Setting
Please refer to section 6 of equipment list in this report. The following table is the setting of the spectrum
analyzer.
Spectrum Parameter
Setting
Detector
Peak
Attenuation
Auto
RB / VB (Emission in restricted band)
100KHz/300KHz
RB / VB (Emission in non-restricted band)
100KHz/300KHz
5.6.3. Test Procedures
The transmitter output is connected to a spectrum analyzer. The resolution bandwidth is set to 100 kHz.
The video bandwidth is set to 300 kHz
The spectrum from 9 kHz to 26.5GHz is investigated with the transmitter set to the lowest, middle, and
highest channels.
5.6.4. Test Setup Layout
This test setup layout is the same as that shown in section 5.4.4.
5.6.5. EUT Operation during Test
The EUT was programmed to be in continuously transmitting mode.
5.6.6. Test Results of Conducted Spurious Emissions
Temperature
25℃
Humidity
60%
Test Engineer
Chaz
Configurations
IEEE 802.11b/g/n
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 34 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
Test Mode
IEEE 802.11b
IEEE 802.11g
IEEE 802.11n
HT20
Channel
11
11
11
Frequency
(MHz)
2412
2437
2462
2412
2437
2462
2412
2437
2462
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
Spurious RF Conducted Emission
(dBc)
<-20
<-20
<-20
<-20
<-20
<-20
<-20
<-20
<-20
Limits
(dBc)
Verdict
-20
PASS
-20
PASS
-20
PASS
Remark:
1. Measured output power at difference data rate for each mode and recorded worst case for each mode.
2. Test results including cable loss;
3. Worst case data at 1Mbps at IEEE 802.11b; 6Mbps at IEEE 802.11g; 6.5Mbps at IEEE 802.11n HT20;
4. “---“means that the fundamental frequency not for 15.209 limits requirement.
5. please refer to following plots;
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 35 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
RF Conducted Spurious Emissions
IEEE 802.11b
2397 – 2427 MHz
9 KHz – 26.5 GHz
2422 – 2452 MHz
9 KHz – 26.5 GHz
2447 – 2477 MHz
9 KHz – 26.5 GHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 36 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
RF Conducted Spurious Emissions
IEEE 802.11g
2397 – 2427 MHz
9 KHz – 26.5 GHz
2422 – 2452 MHz
9 KHz – 26.5 GHz
2447 – 2477 MHz
9 KHz – 26.5 GHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 37 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
RF Conducted Spurious Emissions
IEEE 802.11n HT20
2397 – 2427 MHz
9 KHz – 26.5 GHz
2422 – 2452 MHz
9 KHz – 26.5 GHz
2447 – 2477 MHz
9 KHz – 26.5 GHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 38 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
Band-edge measurements for conducted emissions
IEEE 802.11b
2397 – 2427 MHz
Channel 1 / 2412 MHz
2447 – 2477 MHz
Channel 11 / 2462 MHz
IEEE 802.11g
2397 – 2427 MHz
Channel 1 / 2412 MHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 39 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
Band-edge measurements for conducted emissions
IEEE 802.11g
2447 – 2477 MHz
Channel 11 / 2462 MHz
IEEE 802.11n HT20
2397 – 2427 MHz
Channel 1 / 2412 MHz
2447 – 2477 MHz
Channel 11 / 2462 MHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 40 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.7. AC Power line conducted emissions
5.7.1 Standard Applicable
According to §15.207 (a): For an intentional radiator which is designed to be connected to the public utility
(AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any
frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed 250 microvolts (The limit
decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50 MHz). The limits at
specific frequency range are listed as follows:
Limits (dBμV)
Quasi-peak
66 to 56
56
60
Frequency Range
(MHz)
0.15 to 0.50
0.50 to 5
5 to 30
Average
56 to 46
46
50
* Decreasing linearly with the logarithm of the frequency
5.7.2 Block Diagram of Test Setup
Vert. reference
plane
EMI receiver
EUT
PC
LISN
Reference ground plane
5.7.3 Test Results
PASS
The test data please refer to following page.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 41 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
AC Conducted Emission of power adapter @ AC 120V/60Hz @ IEEE 802.11b (worst case)
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 42 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
AC Conducted Emission of power adapter @ AC 240V/60Hz @ IEEE 802.11b (worst case)
***Note: Pre-scan all modes and recorded the worst case results in this report (IEEE 802.11b).
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 43 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.8. Band-edge measurements for radiated emissions
5.8.1 Standard Applicable
In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated
intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall
be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the
desired power, based on either an RF conducted or a radiated measurement, provided the transmitter
demonstrates compliance with the peak conducted power limits. If the transmitter complies with the
conducted power limits based on the use of RMS averaging over a time interval, as permitted under
paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20
dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated
emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated
emission limits specified in §15.209(a) (see §15.205(c)).
5.8.2. Test Setup Layout
5.8.3. Measuring Instruments and Setting
Please refer to section 6 of equipment list in this report. The following table is the setting of Spectrum
Analyzer.
5.8.4. Test Procedures
1.
2.
3.
4.
5.
6.
7.
8.
According to KDB 558074 D01 V03 for Antenna-port conducted measurement. Antenna-port conducted
measurements may also be used as an alternative to radiated measurements for demonstrating
compliance in the restricted frequency bands. If conducted measurements are performed, then proper
impedance matching must be ensured and an additional radiated test for cabinet/case spurious emissions
is required.
Check the calibration of the measuring instrument using either an internal calibrator or a known signal from
an external generator.
Remove the antenna from the EUT and then connect to a low loss RF cable from the antenna port to a EMI
test receiver, then turn on the EUT and make it operate in transmitting mode. Then set it to Low Channel
and High Channel within its operating range, and make sure the instrument is operated in its linear range.
Set both RBW and VBW of spectrum analyzer to 100 kHz with a convenient frequency span including
100kHz bandwidth from band edge, for Radiated emissions restricted band RBW=1MHz, VBW=3MHz for
peak detector and RBW=1MHz, VBW=1/B for Peak detector.
Measure the highest amplitude appearing on spectral display and set it as a reference level. Plot the graph
with marking the highest point and edge frequency.
Repeat above procedures until all measured frequencies were complete.
Measure the conducted output power (in dBm) using the detector specified by the appropriate regulatory
agency (see 12.2.2, 12.2.3, and 12.2.4 for guidance regarding measurement procedures for determining
quasi-peak, peak, and average conducted output power, respectively).
Add the maximum transmit antenna gain (in dBi) to the measured output power level to determine the
EIRP level (see 12.2.5 for guidance on determining the applicable antenna gain)
Add the appropriate maximum ground reflection factor to the EIRP level (6 dB for frequencies ≤ 30 MHz,
4.7 dB for frequencies between 30 MHz and 1000 MHz, inclusive and 0 dB for frequencies > 1000 MHz).
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 44 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
9. For devices with multiple antenna-ports, measure the power of each individual chain and sum the EIRP of
all chains in linear terms (e.g., Watts, mW).
10. Convert the resultant EIRP level to an equivalent electric field strength using the following relationship:
E = EIRP – 20log D + 104.8
Where:
E = electric field strength in dBμV/m,
EIRP = equivalent isotropic radiated power in dBm
D = specified measurement distance in meters.
11. Since the out-of-band characteristics of the EUT transmit antenna will often be unknown, the use of a
conservative antenna gain value is necessary. Thus, when determining the EIRP based on the measured
conducted power, the upper bound on antenna gain for a device with a single RF output shall be selected
as the maximum in-band gain of the antenna across all operating bands, or 2 dBi, whichever is greater.
However, for devices that operate in multiple frequency bands while using the same transmit antenna, the
highest gain of the antenna within the operating band nearest in frequency to the restricted band emission
being measured may be used in lieu of the overall highest gain when the emission is at a frequency that is
within 20 percent of the nearest band edge frequency, but in no case shall a value less than 2 dBi be used.
12. Compare the resultant electric field strength level to the applicable regulatory limit.
13. Perform radiated spurious emission test duress until all measured frequencies were complete.
5.8.5 Test Results
Frequency
(MHz)
Conducted
Power
(dBm)
Antenna
Gain
(dBi)
2310.000
2310.000
2390.000
2390.000
2483.500
2483.500
2500.000
2500.000
-46.489
-56.885
-41.548
-52.160
-43.202
-52.535
-42.997
-54.091
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
Frequency
(MHz)
Conducted
Power
(dBm)
Antenna
Gain
(dBi)
2310.000
2310.000
2390.000
2390.000
2483.500
2483.500
2500.000
2500.000
-46.473
-56.681
-34.525
-46.718
-32.840
-45.230
-41.204
-52.408
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
IEEE 802.11b
Ground
Covert
Reflection
Radiated E
Factor
Level At 3m
(dB)
(dBuV/m)
0.00
49.771
0.00
39.375
0.00
54.712
0.00
44.100
0.00
53.058
0.00
43.725
0.00
53.263
0.00
42.169
IEEE 802.11g
Ground
Covert
Reflection
Radiated E
Factor
Level At 3m
(dB)
(dBuV/m)
0.00
49.787
0.00
39.579
0.00
61.735
0.00
49.542
0.00
63.420
0.00
51.030
0.00
55.056
0.00
43.852
Detector
Limit
(dBuV/m)
Verdict
Peak
AV
Peak
AV
Peak
AV
Peak
AV
74.00
54.00
74.00
54.00
74.00
54.00
74.00
54.00
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
Detector
Limit
(dBuV/m)
Verdict
Peak
AV
Peak
AV
Peak
AV
Peak
AV
74.00
54.00
74.00
54.00
74.00
54.00
74.00
54.00
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 45 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
Frequency
(MHz)
Conducted
Power
(dBm)
Antenna
Gain
(dBi)
2310.000
2310.000
2390.000
2390.000
2483.500
2483.500
2500.000
2500.000
-46.149
-56.512
-34.102
-46.052
-32.242
-44.903
-41.741
-52.204
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
FCC ID: 2AKNBRT-V03
IEEE 802.11n HT20
Ground
Covert
Reflection
Radiated E
Factor
Level At 3m
(dB)
(dBuV/m)
0.00
50.111
0.00
39.748
0.00
62.158
0.00
50.208
0.00
64.018
0.00
51.357
0.00
54.519
0.00
44.056
Report No.: LCS1612223161E
Detector
Limit
(dBuV/m)
Verdict
Peak
AV
Peak
AV
Peak
AV
Peak
AV
74.00
54.00
74.00
54.00
74.00
54.00
74.00
54.00
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
Remark:
1. Measured output power at difference data rate for each mode and recorded worst case for each mode.
2. Test results including cable loss;
3. Worst case data at 1Mbps at IEEE 802.11b; 6Mbps at IEEE 802.11g; 6.5Mbps at IEEE 802.11n HT20;
4. “---“means that the fundamental frequency not for 15.209 limits requirement.
5. please refer to following plots;
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 46 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
Band-edge measurements for radiated emissions
IEEE 802.11b
IEEE 802.11g
Channel 1 / 2412 MHz – Peak
Channel 1 / 2412 MHz – Peak
Channel 1 / 2412 MHz – Average
Channel 1 / 2412 MHz – Average
Channel 11 / 2462 MHz – Peak
Channel 11 / 2462 MHz – Peak
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 47 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
Band-edge measurements for radiated emissions
IEEE 802.11b
IEEE 802.11g
Channel 11 / 2462 MHz – Average
IEEE 802.11n HT20
Channel 11 / 2462 MHz – Average
IEEE 802.11n HT20
Channel 1 / 2412 MHz – Peak
Channel 11 / 2462 MHz – Peak
Channel 1 / 2412 MHz – Average
Channel 11 / 2462 MHz – Average
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 48 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
5.9. Antenna Requirements
5.9.1. Standard Applicable
According to antenna requirement of §15.203.
An intentional radiator shall be designed to ensure that no antenna other than that furnished by the
responsible party shall be used with the device. The use of a permanently attached antenna or of an
antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply
with the provisions of this Section. The manufacturer may design the unit so that a broken antenna can be
re-placed by the user, but the use of a standard antenna jack or electrical connector is prohibited. This
requirement does not apply to carrier current devices or to devices operated under the provisions of
Sections 15.211, 15.213, 15.217, 15.219, or 15.221. Further, this requirement does not apply to
intentional radiators that must be professionally installed, such as perimeter protection systems and some
field disturbance sensors, or to other intentional radiators which, in accordance with Section 15.31(d),
must be measured at the installation site. However, the installer shall be responsible for ensuring that the
proper antenna is employed so that the limits in this Part are not exceeded.
And according to §15.247(4)(1), system operating in the 2400-2483.5MHz bands that are used
exclusively for fixed, point-to-point operations may employ transmitting antennas with directional gain
greater than 6dBi provided the maximum peak output power of the intentional radiator is reduced by 1 dB
for every 3 dB that the directional gain of the antenna exceeds 6dBi.
5.9.2 Antenna Connected Construction
5.9.2.1. Standard Applicable
According to § 15.203, an intentional radiator shall be designed to ensure that no antenna other than that
furnished by the responsible party shall be used with the device.
5.9.2.2. Antenna Connector Construction
The directional gains of antenna used for transmitting is 1.0 dBi, and the antenna is an internal antenna
connect to PCB board and no consideration of replacement. Please see EUT photo for details.
The WLAN and Bluetooth share same antenna.
5.9.2.3. Results: Compliance.
Measurement
The antenna gain of the complete system is calculated by the difference of radiated power in EIRP and
the conducted power of the module.
Conducted power refers ANSI C63.10:2013 Output power test procedure for DTS devices.
Radiated power refers to ANSI C63.10:2013 Radiated emissions tests.
Measurement parameters
Detector:
Sweep Time:
Resolution bandwidth:
Video bandwidth:
Trace-Mode:
Measurement parameter
Peak
Auto
1MHz
3MHz
Max hold
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 49 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
Note: The antenna gain of the complete system is calculated by the difference of radiated power in EIRP
and the conducted power of the module. For normal WLAN devices, the IEEE 802.11b mode is used.
Limits
FCC
IC
Antenna Gain
6 dBi
Tnom
Vnom
lowest channel
2412 MHz
middle channel
2437 MHz
highest channel
2462 MHz
8.16
8.07
8.31
8.98
8.98
9.13
0.82
0.91
0.82
Conducted power [dBm]
Measured with
DSSS modulation
Radiated power [dBm]
Measured with
DSSS modulation
Gain [dBi] Calculated
Measurement uncertainty
± 1.6 dB (cond.) / ± 3.8 dB (rad.)
Result: -/-
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 50 of 51
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AKNBRT-V03
Report No.: LCS1612223161E
6. LIST OF MEASURING EQUIPMENTS
Instrument
Manufacturer
Model No.
Serial No.
Characteristics
Cal Date
Due Date
EMC Receiver
R&S
ESCS 30
100174
9kHz – 2.75GHz
June 18, 2016
June 17, 2017
Signal analyzer
Agilent
E4448A(External
mixers to 40GHz)
US44300469
9kHz~40GHz
July 16, 2016
July 15, 2017
Signal analyzer
Agilent
N9020A
MY50510140
9kHz~26.5GHz
October 27, 2017
October 27, 2017
LISN
MESS Tec
NNB-2/16Z
99079
9KHz-30MHz
June 18, 2016
June 17, 2017
LISN
(Support Unit)
EMCO
3819/2NM
9703-1839
9KHz-30MHz
June 18, 2016
June 17, 2017
RF Cable-CON
UTIFLEX
3102-26886-4
CB049
9KHz-30MHz
June 18, 2016
June 17, 2017
ISN
SCHAFFNER
ISN ST08
21653
9KHz-30MHz
June 18, 2016
June 17, 2017
3m Semi
Anechoic
Chamber
Amplifier
SIDT
FRANKONIA
SAC-3M
03CH03-HY
30M-18GHz
3m
June 18, 2016
June 17, 2017
SCHAFFNER
COA9231A
18667
9kHz-2GHzz
June 18, 2016
June 17, 2017
Amplifier
Agilent
8449B
3008A02120
1GHz-26.5GHz
July 16, 2016
July 15, 2017
Amplifier
MITEQ
AMF-6F-260400
9121372
26.5GHz-40GHz
July 16, 2016
July 15, 2017
Loop Antenna
R&S
HFH2-Z2
860004/001
9k-30MHz
June 18, 2016
June 17, 2017
By-log Antenna
SCHWARZBEC
VULB9163
9163-470
30MHz-1GHz
June 10, 2016
June 09, 2017
Horn Antenna
EMCO
3115
6741
1GHz-18GHz
June 10, 2016
June 09, 2017
Horn Antenna
SCHWARZBEC
BBHA9170
BBHA9170154
15GHz-40GHz
June 10, 2016
June 09, 2017
RF Cable-R03m
Jye Bao
RG142
CB021
30MHz-1GHz
June 18, 2016
June 17, 2017
RF Cable-HIGH
SUHNER
SUCOFLEX 106
03CH03-HY
1GHz-40GHz
June 18, 2016
June 17, 2017
Power Meter
R&S
NRVS
100444
DC-40GHz
June 18, 2016
June 17, 2017
Power Sensor
R&S
NRV-Z51
100458
DC-30GHz
June 18, 2016
June 17, 2017
Power Sensor
R&S
NRV-Z32
10057
30MHz-6GHz
June 18, 2016
June 17, 2017
AC Power
Source
HPC
HPA-500E
HPA-9100024
AC 0~300V
June 18, 2016
June 17, 2017
DC power Soure
GW
GPC-6030D
C671845
DC 1V-60V
June 18, 2016
June 17, 2017
Giant Force
GTH-225-20-S
MAB0103-00
N/A
June 18, 2016
June 17, 2017
JYE Bao
RG142
CB034-1m
20MHz-7GHz
June 18, 2016
June 17, 2017
RF CABLE-2m
JYE Bao
RG142
CB)35-2m
20MHz-1GHz
June 18, 2016
June 17, 2017
EMC Test
Software
Audix
E3
N/A
N/A
N/A
N/A
Temp. and
Humidigy
Chamber
RF CABLE-1m
Note: All equipment through GRGT EST calibration
----------------THE END OF REPORT--------------This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 51 of 51
Download: RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Mirror Download [FCC.gov]RT-V03 Vr all-in-one Test Report FCC PART 15 SHENZHEN RUIHE TECHNOLOGY CO.,LTD
Document ID3254290
Application IDsCrDQy3QoTz7OscpOEnAhA==
Document DescriptionRF Test Report-wifi
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize382.11kB (4776401 bits)
Date Submitted2017-01-11 00:00:00
Date Available2017-01-11 00:00:00
Creation Date2016-12-29 08:59:25
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2016-12-29 08:59:25
Document TitleFCC PART 15
Document CreatorMicrosoft® Office Word 2007
Document Author: news

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 51
Language                        : zh-CN
Tagged PDF                      : Yes
Title                           : FCC PART 15
Author                          : news
Creator                         : Microsoft® Office Word 2007
Create Date                     : 2016:12:29 08:59:25
Modify Date                     : 2016:12:29 08:59:25
Producer                        : Microsoft® Office Word 2007

Facebook Twitter Google+ RSS © FCCID.io 2017