BX050 Remote Control for Patriot II Brake Test Report Certification Creed Monarch inc

Creed Monarch inc Remote Control for Patriot II Brake

FCC ID Filing: 2AKILBX050
Purchase on Amazon: Remote Control for Patriot II Brake

Trouble Viewing? See the or view the HTML Version or PDF in frame
Page 1 of BX050 Remote Control for Patriot II Brake Test Report Certification Creed Monarch inc

Certification Test Report
FCC ID: 2AKILBX050
IC: 22194-BX050
FCC Rule Part: 15.247
ISED Canada Radio Standards Specification: RSS-247
ACS Report Number: 16-2074.W06.1A
Applicant: Creed Monarch, Inc.
Model(s): BX050
Test Begin Date: November 22, 2016
Test End Date: November 28, 2016
Report Issue Date: January 3, 2017
FOR THE SCOPE OF ACCREDITATION UNDER CERTIFICATE NUMBER AT-1533
This report must not be used by the client to claim product certification, approval, or endorsement by ANAB, ANSI, or any agency of
the Federal Government.
Prepared by:
Reviewed by:
Thierry Jean-Charles
EMC Engineer
Advanced Compliance Solutions, Inc.
Ryan McGann
Wireless Program Manager
Advanced Compliance Solutions, Inc.
This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report
are representative of the sample(s) submitted for evaluation.
This report contains 20 pages
3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587
TABLE OF CONTENTS
GENERAL ...........................................................................................................3
1.1
Purpose ............................................................................................................................................ 3
1.2
Applicant Information ........................................................................................................................ 3
1.3
Product Description .......................................................................................................................... 3
1.4
Test Methodology and Considerations ............................................................................................. 3
TEST FACILITIES ...............................................................................................4
2.1
Location ............................................................................................................................................ 4
2.2
Laboratory Accreditations/Recognitions/Certifications ...................................................................... 4
2.3
Radiated & Conducted Emissions Test Site Description .................................................................. 5
2.3.1
Semi-Anechoic Chamber Test Site ............................................................................................. 5
2.3.2
Conducted Emissions Test Site Description ................................................................................ 6
APPLICABLE STANDARD REFERENCES ........................................................ 7
LIST OF TEST EQUIPMENT ...............................................................................8
SUPPORT EQUIPMENT .....................................................................................9
EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM .................................... 9
SUMMARY OF TESTS ...................................................................................... 10
7.1
Antenna Requirement – FCC: Section 15.203 .................................................................................10
7.2
6 dB Bandwidth - FCC: Section 15.247(a)(2); ISED Canada: RSS-247 5.2(1); 99% Bandwidth ISED
Canada: RSS-GEN 6.6 ....................................................................................................................10
7.2.1
Measurement Procedure ............................................................................................................10
7.2.2
Measurement Results ................................................................................................................10
7.3
Peak Output Power - FCC Section 15.247(b)(3); ISED Canada: RSS-247 5.4(4) ...........................12
7.3.1
Measurement Procedure (Conducted Method) ..........................................................................12
7.3.2
Measurement Results ................................................................................................................12
7.4
Band-Edge and Spurious Emissions ...............................................................................................13
7.4.1
Band-Edge Compliance of RF Conducted Emissions - FCC Section 15.247(d); ISED Canada:
RSS-247 5.5 ...............................................................................................................................13
7.4.1.1 Measurement Procedure ........................................................................................................13
7.4.1.2 Measurement Results ............................................................................................................13
7.4.2
RF Conducted Spurious Emissions - FCC Section 15.247(d); ISED Canada: RSS-247 5.5 ......15
7.4.2.1 Measurement Procedure ........................................................................................................15
7.4.2.2 Measurement Results ............................................................................................................15
7.4.3
Radiated Spurious Emissions into Restricted Frequency Bands – FCC Sections 15.205, 15.209;
ISED Canada: RSS-Gen 8.9, 8.10 .............................................................................................16
7.4.3.1 Measurement Procedure ........................................................................................................16
7.4.3.2 Duty Cycle Correction ............................................................................................................16
7.4.3.3 Measurement Results ............................................................................................................16
7.4.3.4 Sample Calculation: ...............................................................................................................18
7.5
Power Spectral Density - FCC Section 15.247(e); ISED Canada: RSS-247 5.2(2) .........................19
7.5.1
PSD Measurement Procedure (Conducted Method) ..................................................................19
7.5.2
Measurement Results ................................................................................................................19
CONCLUSION .................................................................................................. 20
Model(s): BX050
1.1
FCC ID: 2AKILBX050
IC: 22194-BX050
GENERAL
Purpose
The purpose of this report is to demonstrate compliance with Part 15 Subpart C of the FCC’s Code of
Federal Regulations and Innovation, Science and Economic Development Canada’s Radio Standards
Specification RSS-247 for the tests documented herein.
1.2
Applicant Information
Creed Monarch, Inc.
P O Box 550
New Britain, CT 06050 USA
1.3
Product Description
The Creed Monarch, Inc. Patriot II remote model BX050 is a 12Volt RV battery powered Remote for RV
supplemental Brake. Remote unit is coupled to Brake unit residing in towed car with two-way RF radio
link. The equipment operates in the 900 MHz ISM band. The device also includes a 433 MHz Tire
Pressure Monitor System receiver.
Technical Details
Mode of Operation:
Frequency Range:
Number of Channels:
Channel Separation:
Modulations:
Antenna Type/Gain:
Input Power:
LoRa
922.4 MHz
N/A
CSS
Helical SMD Antenna/ 0.8 dBi
12 VDC
Model Number:
BX050
Test Sample Serial Number(s): ACS#2
Test Sample Condition: The equipment was provided in good condition without any physical damage.
1.4
Test Methodology and Considerations
The 922.4 MHz LoRa transceiver was evaluated for radiated and RF conducted emissions. The test
power setting is not provided and is not configurable via software. The EUT is for vehicle implementation
only with no provision for connection to the AC Mains. The EUT is exempted from the power line
conducted emissions requirements.
For the emissions evaluation, the EUT set in three orthogonal orientations while powered by a DC power
supply.
The RF conducted emissions evaluation was performed on a sample modified with an SMA connector at
the antenna port.
The EUT was also investigated for unintentional emissions. The results are documented separately in a
verification test report.
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 3 of 20
Model(s): BX050
FCC ID: 2AKILBX050
IC: 22194-BX050
TEST FACILITIES
2.1
Location
The radiated and conducted emissions test sites are located at the following address:
Advanced Compliance Solutions, Inc.
3998 FAU Blvd, Suite 310
Boca Raton, Florida 33431
Phone: (561) 961-5585
Fax: (561) 961-5587
www.acstestlab.com
FCC Test Firm Registration #: 475089
Innovation, Science and Economic Development Canada Lab Code: 4175C
2.2
Laboratory Accreditations/Recognitions/Certifications
ACS is accredited to ISO/IEC 17025 by ANSI-ASQ National Accreditation Board under their ANAB
program and has been issued certificate number AT-1533 in recognition of this accreditation. Unless
otherwise specified, all test methods described within this report are covered under the ISO/IEC 17025
scope of accreditation.
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 4 of 20
Model(s): BX050
2.3
FCC ID: 2AKILBX050
IC: 22194-BX050
Radiated & Conducted Emissions Test Site Description
2.3.1 Semi-Anechoic Chamber Test Site
The EMC radiated test facility consists of an RF-shielded enclosure. The interior dimensions of the indoor
semi-anechoic chamber are approximately 48 feet (14.6 m) long by 36 feet (10.8 m) wide by 24 feet (7.3
m) high and consist of rigid, 1/8 inch (0.32 cm) steel-clad, wood core modular panels with steel framing.
In the shielded enclosure, the faces of the panels are galvanized and the chamber is self-supporting. 8foot RF absorbing cones are installed on 4 walls and the ceiling. The steel-clad ground plane is covered
with vinyl flooring.
The turntable is driven by pneumatic motor, which is capable of supporting a 2000 lb. load. The turntable
is flush with the chamber floor which it is connected to, around its circumference, with a continuous
metallic loaded spring. An EMCO Model 1060 Multi-device controller controls the turntable position.
A pneumatic motor is used to control antenna polarizations and height relative to the ground. The height
information is displayed on the control unit EMCO Model 1050.
The control room is an RF shielded enclosure attached to the semi-anechoic chamber with two bulkhead
panels for connecting RF, and control cables. The dimension of the room is 7.3 m x 4.9 m x 3 m high and
the entrance doors of both control and conducted rooms are 3 feet (0.91 m) by 7 feet (2.13 m).
A diagram of the Semi-Anechoic Chamber Test Site is shown in Figure 2.3.1-1 below:
3m
8m
14.78m
7.33m
4.9m
4.9m
Conducted EMI Site
Control Room
7.33m
Figure 2.3.1-1: Semi-Anechoic Chamber Test Site
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 5 of 20
Model(s): BX050
FCC ID: 2AKILBX050
IC: 22194-BX050
2.3.2 Conducted Emissions Test Site Description
The dimensions of the shielded conducted room are 7.3 x 4.9 x 3 m . The power line conducted emission
site includes two LISNs: a Solar Model 8028-50 50 Ω/50 μH and an EMCO Model 3825/2R, which are
installed as shown in the figure below. For evaluations requiring 230 V, 50 Hz AC input, a Polarad LISN
(S/N 879341/048) is used in conjunction with a California Instruments signal generator Model 2001RPOP1.
A diagram of the room is shown below in figure 2.3.2-1:
4.9m\16ft
LISN
1.0m x 1.5m
Non-Conductive Table
LISN
7.33m\24ft.
Figure 2.3.2-1: AC Mains Conducted EMI Site
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 6 of 20
Model(s): BX050
FCC ID: 2AKILBX050
IC: 22194-BX050
APPLICABLE STANDARD REFERENCES
The following standards were used:
 ANSI C63.4-2014: Method of Measurements of Radio-Noise Emissions from Low-Voltage
Electrical and Electronic Equipment in the 9 kHz to 40 GHz.
 ANSI C63.10-2013: American National Standard of Procedures for Compliance Testing of
Unlicensed Wireless Devices
 US Code of Federal Regulations (CFR): Title 47, Part 2, Subpart J: Equipment Authorization
Procedures, 2016.
 US Code of Federal Regulations (CFR): Title 47, Part 15, Subpart C: Radio Frequency Devices,
Intentional Radiators, 2016
 FCC KDB 558074 D01 DTS Meas Guidance v03r05 - Guidance for Performing Compliance
Measurements on Digital Transmission Systems (DTS) Operating Under §15.247, April 8, 2016.
 Innovation, Science and Economic Development Canada Radio Standards Specification: RSS247 — Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and LicenceExempt Local Area Network (LE-LAN) Devices, Issue 1, May 2015.
 Innovation, Science and Economic Development Canada Radio Standards Specification: RSSGEN – General Requirements for Compliance of Radio Apparatus, Issue 4, November 2014.
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 7 of 20
Model(s): BX050
FCC ID: 2AKILBX050
IC: 22194-BX050
LIST OF TEST EQUIPMENT
The calibration interval of test equipment is annually or the manufacturer’s recommendations. Where the
calibration interval deviates from the annual cycle based on the instrument manufacturer’s
recommendations, it shall be stated below.
Table 4-1: Test Equipment List
AssetID
22
78
283
523
2002
2004
2006
2011
2071
2086
2095
2111
2112
2121
Manufacturer
Agilent
EMCO
Rohde & Schwarz
Agilent
EMCO
EMCO
EMCO
Hewlett-Packard
Trilithic, Inc.
Merrimac
ETS Lindgren
Aeroflex Inmet
Teledyne Storm Products
ACS Boca
Model #
8449B
6502
FSP40
E7405
3108
3146
3115
HP 8447D
4HC1400-1-KK
FAN-6-10K
TILE4! - Version 4.2.A
40AH2W-20
921-0101-036
Radiated Cable Set
Equipment Type
Amplifiers
Antennas
Spectrum Analyzers
Spectrum Analyzers
Antennas
Antennas
Antennas
Amplifiers
Filter
Attenuators
Software
Attenuator
Cables
Cable Set
Serial #
3008A00526
9104-2608
1000033
MY45103293
2147
1385
2573
2443A03952
9643263
23148-83-1
85242
2111
12-06-698
2121
Last Calibration Date
Calibration
Due Date
7/14/2016
5/11/2016
7/21/2016
12/26/2014
11/19/2015
11/19/2015
4/14/2015
11/2/2016
11/1/2016
11/2/2016
NCR
7/20/2016
11/2/2016
8/1/2016
7/14/2018
5/11/2018
7/21/2018
12/26/2016
11/19/2017
11/19/2017
4/14/2017
11/2/2017
11/1/2017
11/2/2017
NCR
7/20/2017
11/2/2017
8/1/2017
Note: NCR=No Calibration Required
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 8 of 20
Model(s): BX050
FCC ID: 2AKILBX050
IC: 22194-BX050
SUPPORT EQUIPMENT
Table 5-1: EUT and Support Equipment Description
Item
Type Device
Manufacturer
Model/Part #
Serial #
EUT
Creed Monarch
BX050
ACS#2
Cigarette Lighter Plug
Creed Monarch
N/A
ACS#3
DC Power Supply
MPJA
HY5003
003700278
Table 5-2: Cable Description
Cable
Cable Type
Length
Shield
Termination
Power cable
3m
No
EUT to Cigarette Lighter Plug
2-Wire Power Leads
1.95 m
No
Cigarette Lighter Plug to Power Supply
MPJA Power Cable
1.8 m
No
Power Supply to AC Mains
EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM
AC Mains
Figure 6-1: EUT Test Setup
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 9 of 20
Model(s): BX050
FCC ID: 2AKILBX050
IC: 22194-BX050
SUMMARY OF TESTS
Along with the tabular data shown below, plots were taken of all signals deemed important enough to
document.
7.1
Antenna Requirement – FCC: Section 15.203
The EUT uses an integral 0.8 dBi helical SMD antenna which is directly soldered to the PCB. The
antennan is not removable and therefore meets the requirements of FCC Section 15.203.
7.2
7.2.1
6 dB Bandwidth - FCC: Section 15.247(a)(2); ISED Canada: RSS-247 5.2(1); 99% Bandwidth
ISED Canada: RSS-GEN 6.6
Measurement Procedure
The 6dB bandwidth was measured in accordance with the FCC KDB 558074 D01 DTS Meas Guidance
v03r05 Section 8.2 Option 2. The RBW of the spectrum analyzer was set to 100 kHz and VBW 300 kHz.
Span was set large enough to capture the emissions and >> RBW.
The 99% occupied bandwidth was measured with the spectrum analyzer span set to fully display the
emission. The RBW was set to 1% to 5% of the approximated bandwidth. The occupied 99% bandwidth
was measured by using 99% bandwidth equipment function of the spectrum analyzer.
7.2.2
Measurement Results
Results are shown below.
Frequency
[MHz]
922.4
ACS Report: 16-2074.W06.1A
Table 7.2.2-1: 6dB / 99% Bandwidth
6dB Bandwidth
99% Bandwidth
[kHz]
[kHz]
762.00
616.00
Advanced Compliance Solutions
Page 10 of 20
Model(s): BX050
FCC ID: 2AKILBX050
*RBW 100 kHz
Ref
20 dBm
20 Offset
Att
30 dB
20.4 dB
Marker 1 [T1 ]
7.69 dBm
922.348000000 MHz
ndB [T1]
6.00
BW 762.000000000
Temp 1 [T1 ndB]
1.80
T2
922.008000000
Temp 2 [T1 ndB]
1.59
922.770000000
10
1 PK
MAXH
VBW 300 kHz
SWT 2.5 ms
T1
-10
IC: 22194-BX050
dB
kHz
dBm
MHz
LVL
dBm
MHz
-20
-30
3DB
-40
-50
-60
-70
-80
Center 922.4 MHz
Date: 22.NOV.2016
100 kHz/
Span 1 MHz
13:27:38
Figure 7.2.2-1: 6dB BW
*RBW 10 kHz
Ref
20 dBm
20 Offset
Att
20 dB
VBW 30 kHz
SWT 20 ms
20.4 dB
10
1 SA*
MAXH 0
T2
Marker 1 [T1 ]
3.96 dBm
922.572000000 MHz
OBW616.000000000
Temp 1 [T1 OBW]
-10.51
922.084000000
Temp 2 [T1 OBW]
-7.42
922.700000000
kHz
dBm A
MHz
dBm LVL
MHz
T1
-10
-20
-30
3DB
-40
-50
-60
-70
-80
Center 922.4 MHz
Date: 22.NOV.2016
200 kHz/
Span 2 MHz
13:40:09
Figure 7.2.2-2: 99% OBW
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 11 of 20
Model(s): BX050
FCC ID: 2AKILBX050
IC: 22194-BX050
7.3
Peak Output Power - FCC Section 15.247(b)(3); ISED Canada: RSS-247 5.4(4)
7.3.1
Measurement Procedure (Conducted Method)
The fundamental emission output power was measured in accordance with the FCC KDB 558074 D01
DTS Meas Guidance v03r05 Section 9.1.1 RBW ≥ DTS bandwidth. The RF output of the equipment
under test was directly connected to the input of the spectrum analyzer through suitable attenuation.
7.3.2
Measurement Results
Results are shown below.
Table 7.3.2-1: RF Output Power
Frequency
Level
[MHz]
[dBm]
922.4
7.92
*RBW 3 MHz
Ref
20 dBm
20 Offset
Att
30 dB
Marker 1 [T1 ]
7.92 dBm
922.180000000 MHz
20.4 dB
10
1 PK
MAXH
VBW 10 MHz
SWT 2.5 ms
LVL
-10
-20
-30
3DB
-40
-50
-60
-70
-80
Center 922.4 MHz
Date: 22.NOV.2016
1 MHz/
Span 10 MHz
13:33:28
Figure 7.3.2-1: RF Output Power
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 12 of 20
Model(s): BX050
7.4
FCC ID: 2AKILBX050
IC: 22194-BX050
Band-Edge and Spurious Emissions
7.4.1
7.4.1.1
Band-Edge Compliance of RF Conducted Emissions - FCC Section 15.247(d); ISED
Canada: RSS-247 5.5
Measurement Procedure
The RF output port of the EUT was directly connected to the input of the spectrum analyzer via suitable
attenuation. The EUT was investigated at the transmitting channel to determine band-edge compliance.
For each measurement the spectrum analyzer’s RBW was set to 100 kHz, and the VBW was set to 300
kHz.
7.4.1.2
Measurement Results
Results are shown below.
*RBW 100 kHz
Ref
20 dBm
20 Offset
10
1 PK
MAXH
Att
30 dB
VBW 300 kHz
SWT 2.5 ms
20.4 dB
Delta 1 [T1 ]
50.31 dB
22.100000000 MHz
Marker 1 [T1 ]
-42.05 dBm
900.100001
0000 MHz A
D1 7.68 dBm
LVL
-10
D2 -12.32 dBm
-20
-30
3DB
1-40
-50
-60
-70
F1
-80
Start 900 MHz
Date: 26.NOV.2016
2.5 MHz/
Stop 925 MHz
19:29:59
Figure 7.4.1.2-1: Lower Band-edge
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 13 of 20
Model(s): BX050
FCC ID: 2AKILBX050
*RBW 100 kHz
Ref
20 dBm
20 Offset
10
1 PK
MAXH
Att
30 dB
VBW 300 kHz
SWT 2.5 ms
20.4 dB
IC: 22194-BX050
Delta 1 [T1 ]
49.74 dB
-7.660000000 MHz
Marker 1 [T1 ]
-42.13 dBm
929.920000000 MHz A
D1 7.68 dBm
LVL
-10
D2 -12.32 dBm
-20
-30
3DB
-40
-50
-60
-70
F1
-80
Start 920 MHz
Date: 26.NOV.2016
1 MHz/
Stop 930 MHz
19:31:25
Figure 7.4.1.2-2: Upper Band-edge
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 14 of 20
Model(s): BX050
7.4.2
7.4.2.1
FCC ID: 2AKILBX050
IC: 22194-BX050
RF Conducted Spurious Emissions - FCC Section 15.247(d); ISED Canada: RSS-247 5.5
Measurement Procedure
The RF Conducted Spurious Emissions were measured in accordance with the FCC KDB 558074 D01
DTS Meas Guidance v03r05 Section 11.3 Emission level measurement. The RF output port of the
equipment under test was directly connected to the input of the spectrum analyzer. The EUT was
investigated for conducted spurious emissions from 30MHz to 10 GHz, 10 times the highest fundamental
frequency. The spectrum analyzer’s RBW was set to 100 kHz and the VBW was set to 300 kHz. The
peak Max Hold function of the analyzer was utilized. The reference level was determined by measuring
the Peak PSD level in any 100 kHz bandwidth within the DTS channel bandwidth.
7.4.2.2
Measurement Results
Results are shown below.
*RBW 100 kHz
Ref
*Att
20 dBm
30 dB
VBW 300 kHz
SWT 1 s
20
10
1 PK
MAXH
Marker 1 [T1 ]
7.94 dBm
922.315000000 MHz
Marker 2 [T1 ]
-25.40 dBm
9.355688750 GHz A
D1 7.68 dBm
TDF
-10
D2 -12.32 dBm
-20
-30
3DB
-40
-50
-60
-70
-80
Start 30 MHz
Date: 22.NOV.2016
997 MHz/
Stop 10 GHz
13:45:04
Figure 7.4.2.2-1: 30 MHz – 10 GHz
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 15 of 20
Model(s): BX050
7.4.3
7.4.3.1
FCC ID: 2AKILBX050
IC: 22194-BX050
Radiated Spurious Emissions into Restricted Frequency Bands – FCC Sections 15.205,
15.209; ISED Canada: RSS-Gen 8.9, 8.10
Measurement Procedure
Radiated emissions tests were made over the frequency range of 9 kHz to 10 GHz, 10 times the highest
fundamental frequency. Each emission found to be in a restricted band as defined by section 15.205,
including any emission at the operational band-edge, was compared to the radiated emission limits as
defined in Section 15.209.
For measurements below 30 MHz, the receive antenna height was set to 1m and the EUT was rotated
through 360 degrees. The resolution bandwidth was set to 200 Hz below 150 kHz and to 9 kHz above
150 kHz.
The EUT was rotated through 360° and the receive antenna height was varied from 1m to 4m so that the
maximum radiated emissions level would be detected. For frequencies below 1000MHz, quasi-peak
measurements were made using a resolution bandwidth RBW of 120 kHz and a video bandwidth VBW of
300 kHz. For frequencies above 1000 MHz, peak measurements are made with RBW of 1 MHz and
VBW of 3 MHz. Average measurements are performed in the linear scale using VBW of 30 Hz.
7.4.3.2 Duty Cycle Correction
The average measurements were further corrected using a duty cycle correction factor corresponding to
20*log(14/100) = -17.08 dB. Justification for the duty cycle of the transceiver is provided in the Theory of
Operation of the device.
7.4.3.3
Measurement Results
Radiated band-edge and spurious emissions found in the restricted frequency bands of 9 kHz to 10 GHz
are reported in the tables below.
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 16 of 20
Model(s): BX050
FCC ID: 2AKILBX050
IC: 22194-BX050
Table 7.4.3.3-1: Radiated Spurious Emissions Tabulated Data
Level
(dBuV)
Frequency
(MHz)
pk
Qpk/Avg
Antenna
Polarity
Correction
(H/V)
(dB)
Factors
Corrected Level
(dBuV/m)
Limit
(dBuV/m)
Margin
(dB)
pk
Qpk/Avg
pk
Qpk/Avg
pk
Qpk/Avg
57.40
54.32
54.97
53.43
56.96
55.82
71.57
72.82
67.83
67.02
35.00
31.47
30.10
28.09
30.30
29.37
42.91
44.17
38.16
37.30
74.0
74.0
74.0
74.0
74.0
74.0
74.0
74.0
74.0
74.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
16.6
19.7
19.0
20.6
17.0
18.2
2.4
1.2
6.2
7.0
19.0
22.5
23.9
25.9
23.7
24.6
11.1
9.8
15.8
16.7
56.50
51.79
55.22
52.64
53.42
56.76
68.35
68.01
63.44
66.87
34.94
29.67
31.97
28.80
27.56
33.20
42.58
42.06
35.71
40.05
74.0
74.0
74.0
74.0
74.0
74.0
74.0
74.0
74.0
74.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
17.5
22.2
18.8
21.4
20.6
17.2
5.7
6.0
10.6
7.1
19.1
24.3
22.0
25.2
26.4
20.8
11.4
11.9
18.3
13.9
54.39
54.64
51.92
55.10
55.84
55.89
69.21
72.48
66.16
67.76
31.54
32.24
25.25
29.99
29.10
29.21
40.12
43.60
36.33
37.71
74.0
74.0
74.0
74.0
74.0
74.0
74.0
74.0
74.0
74.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
19.6
19.4
22.1
18.9
18.2
18.1
4.8
1.5
7.8
6.2
22.5
21.8
28.7
24.0
24.9
24.8
13.9
10.4
17.7
16.3
Flat
2767.2
2767.2
3689.6
3689.6
4612
4612
7379.2
7379.2
8301.6
8301.6
55.61
52.53
49.68
48.14
49.90
48.76
58.61
59.86
54.20
53.39
50.29
46.76
41.89
39.88
40.31
39.38
47.03
48.29
41.61
40.75
2767.2
2767.2
3689.6
3689.6
4612
4612
7379.2
7379.2
8301.6
8301.6
54.71
50.00
49.93
47.35
46.36
49.70
55.39
55.05
49.81
53.24
50.23
44.96
43.76
40.59
37.57
43.21
46.70
46.18
39.16
43.50
2767.2
2767.2
3689.6
3689.6
4612
4612
7379.2
7379.2
8301.6
8301.6
52.60
52.85
46.63
49.81
48.78
48.83
56.25
59.52
52.53
54.13
46.83
47.53
37.04
41.78
39.11
39.22
44.24
47.72
39.78
41.16
1.79
1.79
5.29
5.29
7.06
7.06
12.96
12.96
13.63
13.63
Standing
1.79
1.79
5.29
5.29
7.06
7.06
12.96
12.96
13.63
13.63
Side
1.79
1.79
5.29
5.29
7.06
7.06
12.96
12.96
13.63
13.63
Notes:
All the emissions above 8.31 GHz were attenuated below the limits and the noise floor of the
measurement equipment.
A duty cycle correction factor of -17.08 dB was used for the calculation of the corrected average
levels.
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 17 of 20
Model(s): BX050
FCC ID: 2AKILBX050
IC: 22194-BX050
7.4.3.4 Sample Calculation:
RC = RU + CFT
Where:
CFT
RU
RC
AF
CA
AG
DC
Total Correction Factor (AF+CA+AG)-DC (Average Measurements Only)
Uncorrected Reading
Corrected Level
Antenna Factor
Cable Attenuation
Amplifier Gain
Duty Cycle Correction Factor
Example Calculation: Peak
Corrected Level: 55.61+ 1.79 = 57.4 dBµV/m
Margin: 74 dBµV/m – 57.4 dBµV/m = 16.6 dB
Example Calculation: Average
Corrected Level: 50.29 + 1.79 - 17.08 = 35.0 dBµV/m
Margin: 54 dBµV/m – 35.0 dBµV/m = 19.0 dB
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 18 of 20
Model(s): BX050
7.5
FCC ID: 2AKILBX050
IC: 22194-BX050
Power Spectral Density - FCC Section 15.247(e); ISED Canada: RSS-247 5.2(2)
7.5.1 PSD Measurement Procedure (Conducted Method)
The power spectral density was measured in accordance with the FCC KDB 558074 D01 DTS Meas
Guidance v03r05 Section 10.2 Method PKPSD (peak PSD). The RF output port of the EUT was directly
connected to the input of the spectrum analyzer. Offset values were input for cable and external
attenuation. The spectrum analyzer RBW was set to 3 kHz and VBW 10 kHz. Span was adjusted to 1.5
times the 6 dB bandwidth and the sweep time was set to auto.
7.5.2
Measurement Results
Results are shown below.
Table 7.5.2-1: Power Spectral Density
Frequency
[MHz]
PSD
[dBm]
Limit
[dBm]
Margin
[dB]
922.4
-4.66
8.0
12.66
*RBW 3 kHz
Ref
20 dBm
20 Offset
Att
30 dB
VBW 10 kHz
SWT 130 ms
Marker 1 [T1 ]
-4.66 dBm
922.576022000 MHz
20.4 dB
10
1 PK
MAXH
LVL
-10
-20
-30
3DB
-40
-50
-60
-70
-80
Center 922.4 MHz
Date: 22.NOV.2016
114.3 kHz/
Span 1.143 MHz
13:31:37
Figure 7.5.2-1: Power Spectral Density
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 19 of 20
Model(s): BX050
FCC ID: 2AKILBX050
IC: 22194-BX050
CONCLUSION
In the opinion of ACS, Inc., the model BX050 manufactured by Creed Monarch, Inc. meets the
requirements of FCC Part 15 subpart C and Innovation, Science and Economic Development Canada’s
Radio Standards Specification RSS-247 for the test procedures documented in the test report.
END REPORT
ACS Report: 16-2074.W06.1A
Advanced Compliance Solutions
Page 20 of 20
Download: BX050 Remote Control for Patriot II Brake Test Report Certification Creed Monarch inc
Mirror Download [FCC.gov]BX050 Remote Control for Patriot II Brake Test Report Certification Creed Monarch inc
Document ID3254701
Application IDOvjOKL9RnvhqB5Rs3GMv/A==
Document DescriptionTest Report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize22.24kB (277997 bits)
Date Submitted2017-01-11 00:00:00
Date Available2017-01-11 00:00:00
Creation Date2017-12-20 17:06:35
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-12-20 17:06:35
Document TitleCertification Test Report
Document CreatorAcrobat PDFMaker 11 for Word
Document Author: sam.mendolia

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:97423687-a265-11f2-0000-02c7314339d4
Producer                        : GPL Ghostscript 9.18
Modify Date                     : 2017:07:16 17:06:00Z
Create Date                     : 2017:07:16 17:06:00Z
Creator Tool                    : UnknownApplication
Document ID                     : uuid:97423687-a265-11f2-0000-02c7314339d4
Format                          : application/pdf
Title                           : Untitled
EXIF Metadata provided by EXIF.tools

Facebook Twitter Google+ RSS © FCCID.io 2018