FCC ID 2A3G3-WMX8202

CIIPC for this application. This change establishes portable category SAR conditions. The minimum test separation distance is 5mm. The PIFA antenna Brand: HONGBO / Model: 260-25083 highest reported Body SAR, PD and Simultaneous SAR values are 0.74 W/kg, 5.01W/m2 and 1.58 W/kg, respectively.

Single Modular Approval. Power listed is the EIRP. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. This device has 20 MHz, 40 MHz, 80 MHz, 160 MHz and 320 MHz bandwidth modes. For 5.925-7.125GHz band operation, the PIFA antenna (Maximum 5.16 dBi gain) and Monopole antenna (Maximum 4.81 dBi gain) can be used with this approval. Device must compliant indoor restrictions when connected to indoor low power AP.

CIIPC for this application. This change establishes portable category SAR conditions. The minimum test separation distance is 5mm. The PIFA antenna Brand: HONGBO / Model: 260-25094 highest reported Body and Simultaneous SAR values are 0.79 W/kg and 1.58 W/kg, respectively.

Single Modular Approval. Power listed is the maximum conducted output power. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369.

The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter.

The module antenna(s) must be installed to meet the RF exposure compliance separation distance. The minimum test separation distance is 5mm. The PIFA antenna Brand: HONGBO / Model: 260-25083 highest reported Body SAR, PD and Simultaneous SAR values are 0.74 W/kg, 5.01W/m2 and 1.58 W/kg, respectively, any additional testing and authorization process as required.

The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The host-product antenna must be permanently installed and not replaceable by the end user. Any attempt to replace or modify the antenna by the end user is strictly prohibited and will void the FCC certification. This device has 20 MHz, 40 MHz, 80 MHz, 160 MHz and 320 MHz bandwidth modes.

Single Modular Approval. U-NII-1 through U-NII-3 Power listed is the maximum combined conducted output power, U-NII-4 and U-NII -3 & -4 span channels Power listed is the EIRP. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369.

The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. This device has 20 MHz, 40 MHz, 80 MHz and 160 MHz bandwidth modes.

Single Modular Approval. Power listed is the maximum combined conducted output power. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369.

The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. This device has 20 MHz and 40 MHz bandwidth modes.