IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH

i.safe MOBILE GmbH Intrinsically safe Tablet PC

Page 1 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 2 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 3 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 4 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 5 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 6 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 7 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 8 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 9 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 10 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 11 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 12 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 13 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 14 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 15 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 16 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 17 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 18 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 19 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 20 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 21 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 22 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 23 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 24 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 25 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 26 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 27 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 28 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 29 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 30 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 31 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 32 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 33 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 34 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 35 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 36 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 37 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 38 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 39 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 40 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 41 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 42 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 43 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 44 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 45 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 46 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 47 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 48 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 49 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 50 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 51 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 52 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 53 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 54 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 55 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 56 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 57 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 58 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 59 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 60 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 61 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 62 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 63 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 64 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 65 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 66 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 67 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 68 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 69 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 70 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 71 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 72 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Page 73 of IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH

SAR EVALUATION REPORT
For
i.safe MOBILE GmbH
i_Park Tauberfranken 10 97922 Lauda-Koenigshofen, Germany
FCC ID: 2AACZ-IS9101
Report Type:
Product Type:
Original Report
Intrinsically safe tablet PC
Report Number:
RSZ180529003-20A
Report Date:
2018-07-23
Reviewed By:
Rocky Xiao
RF Engineer
Prepared By:
Bay Area Compliance Laboratories Corp. (Dongguan)
No.69 Pulongcun, Puxinhu Industry Area,
Tangxia, Dongguan, Guangdong, China
Tel: +86-769-86858888
Fax: +86-769-86858891
www.baclcorp.com.cn
Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or
used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Dongguan).
This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA* or any agency of
the Federal Government. * This report may contain data that are not covered by the A2LA accreditation and are marked with an
asterisk “*”
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
Attestation of Test Results
EUT Description
EUT
Information
Tested Model
IS910.1
Multiple Model
RG910
FCC ID
Serial Number
Test Date
MODE
GSM 850
PCS 1900
CDMA 850(BC0)
CDMA 1900(BC1)
WCDMA Band 2
WCDMA Band 5
LTE Band 7
LTE Band 41
WLAN 2.4G
Bluetooth
1g Body SAR
1g Body SAR
1g Body SAR
1g Body SAR
1g Body SAR
1g Body SAR
1g Body SAR
1g Body SAR
1g Body SAR
1g Body SAR
1g Body SAR
1g Body SAR
Simultaneous
Intrinsically safe tablet PC
2AACZ-IS9101
18052900321 (IS910.1)
18052900322 (RG910)
2018-06-09 ~ 2018-06-13
Max. SAR Level(s) Reported(W/kg)
Limit (W/kg)
0.20
1.12
0.44
0.97
1.05
0.24
0.37
0.25
0.08
0.04
1.20
1.20 (Hotspot)
1. 6
FCC 47 CFR part 2.1093
Radiofrequency radiation exposure evaluation: portable devices
IEEE1528:2013
IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption
Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement
Techniques
IEC 62209-2:2010
Human exposure to radio frequency fields from hand-held and body-mounted wireless
Applicable
communication devices-Human models, instrumentation, and procedures-Part 2: Procedure to
Standards
determine the specific absorption rate (SAR) for wireless communication devices used in
close proximity to the human body (frequency range of 30 MHz to 6 GHz)
KDB procedures
KDB 447498 D01 General RF Exposure Guidance v06
KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04
KDB 865664 D02 RF Exposure Reporting v01r02
KDB 941225 D01 3G SAR Procedures v03r01
KDB 941225 D05 SAR for LTE Devices v02r05
KDB 941225 D06 Hotspot Mode v02r01
KDB 248227 D01 802 11 Wi-Fi SAR v02r02
Note: This wireless device has been shown to be capable of compliance for localized specific absorption rate (SAR)
for General Population/Uncontrolled Exposure limits specified in FCC 47 CFR part 2.1093 and has been tested in
accordance with the measurement procedures specified in IEEE 1528-2013 and RF exposure KDB procedures.
The results and statements contained in this report pertain only to the device(s) evaluated.
SAR Evaluation Report
2 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
TABLE OF CONTENTS
DOCUMENT REVISION HISTORY ......................................................................................................................... 4
EUT DESCRIPTION .................................................................................................................................................... 5
TECHNICAL SPECIFICATION ......................................................................................................................................... 5
REFERENCE, STANDARDS, AND GUIDELINES.................................................................................................. 6
SAR LIMITS ................................................................................................................................................................. 7
FACILITIES .................................................................................................................................................................. 8
DESCRIPTION OF TEST SYSTEM .......................................................................................................................... 9
EQUIPMENT LIST AND CALIBRATION ............................................................................................................. 14
EQUIPMENTS LIST & CALIBRATION INFORMATION .................................................................................................... 14
SAR MEASUREMENT SYSTEM VERIFICATION .............................................................................................. 15
LIQUID VERIFICATION ............................................................................................................................................... 15
SYSTEM ACCURACY VERIFICATION ........................................................................................................................... 17
SAR SYSTEM VALIDATION DATA ..................................................................................................................... 18
EUT TEST STRATEGY AND METHODOLOGY ................................................................................................. 22
TEST POSITIONS FOR DEVICE OPERATING NEXT TO A PERSON’S EAR........................................................................ 22
CHEEK/TOUCH POSITION ........................................................................................................................................... 23
EAR/TILT POSITION ................................................................................................................................................... 23
TEST POSITIONS FOR BODY-WORN AND OTHER CONFIGURATIONS .............................................................................. 24
TEST DISTANCE FOR SAR EVALUATION .................................................................................................................... 24
SAR EVALUATION PROCEDURE ................................................................................................................................. 25
CONDUCTED OUTPUT POWER MEASUREMENT ........................................................................................... 26
PROVISION APPLICABLE ............................................................................................................................................ 26
TEST PROCEDURE ...................................................................................................................................................... 26
RADIO CONFIGURATION ............................................................................................................................................ 26
MAXIMUM TARGET OUTPUT POWER ......................................................................................................................... 33
IS910.1 TEST RESULTS: ............................................................................................................................................ 34
RG910 TEST RESULTS: ............................................................................................................................................. 43
STANDALONE SAR TEST EXCLUSION CONSIDERATIONS ......................................................................... 52
ANTENNA DISTANCE TO EDGE .................................................................................................................................. 52
STANDALONE SAR TEST EXCLUSION CONSIDERATIONS ............................................................................................. 52
STANDALONE SAR TEST EXCLUSION CONSIDERATIONS DETAIL: ............................................................................... 53
SAR TEST EXCLUSION FOR THE EUT EDGE CONSIDERATIONS RESULT ...................................................................... 53
SAR MEASUREMENT RESULTS ........................................................................................................................... 55
SAR TEST DATA ........................................................................................................................................................ 55
SAR MEASUREMENT VARIABILITY .................................................................................................................. 66
SAR SIMULTANEOUS TRANSMISSION DESCRIPTION ................................................................................. 67
SAR PLOTS ................................................................................................................................................................. 69
APPENDIX A MEASUREMENT UNCERTAINTY ............................................................................................... 70
APPENDIX B EUT TEST POSITION PHOTOS .................................................................................................... 72
APPENDIX C CALIBRATION CERTIFICATES .................................................................................................. 73
SAR Evaluation Report
3 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
DOCUMENT REVISION HISTORY
Revision Number
Report Number
Description of Revision
Date of Revision
1.0
RSZ180529003-20A
Original Report
2018-07-23
SAR Evaluation Report
4 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
EUT DESCRIPTION
This report has been prepared on behalf of i.safe MOBILE GmbH and their product Intrinsically safe
tablet PC, Model: IS910.1, FCC ID: 2AACZ-IS9101 or the EUT (Equipment under Test) as referred to in
the rest of this report.
*All measurement and test data in this report was gathered from production sample serial number: 18052900321 for
IS910.1 and 18052900322 for RG910(Assigned by BACL, Dongguan). The EUT supplied by the applicant was
received on 2018-05-31.
Technical Specification
Device Type:
Exposure Category:
Antenna Type(s):
DTM Type:
Multi-slot Class:
Body-Worn Accessories:
Face-Head Accessories:
Portable
Population / Uncontrolled
Internal Antenna
Class B
GPRS(Class 12); EGPRS(Class 12)
Headset
None
GSM Voice, GPRS/EDGE Data, CDMA 1xRTT, 1xEVDO Rev.A,
Operation Mode :
Frequency Band:
Conducted RF Power:
Power Source:
Normal Operation:
SAR Evaluation Report
WCDMA( R99 (Voice+Data), HSDPA/HSUPA/HSPA+), FDD-LTE,
TDD-LTE, WLAN, Bluetooth
GSM 850: 824-849 MHz(TX); 869-894 MHz(RX)
PCS 1900: 1850-1910 MHz(TX); 1930-1990 MHz(RX)
CDMA 850(BC0): 824-849 MHz(TX) ; 869-894 MHz(RX)
CDMA 1900(BC1): 1850-1910 MHz(TX) ; 1930-1990 MHz(RX)
WCDMA Band 2: 1850-1910 MHz(TX); 1930-1990 MHz(RX)
WCDMA Band 5: 824-849 MHz(TX); 869-894 MHz(RX)
LTE Band 7: 2500-2570 MHz(TX) ; 2620-2690 MHz(RX)
LTE Band 41: 2555-2655 MHz(TX) ; 2555-2655 MHz(RX)
WLAN: 2412 -2462 MHz /2422 -2452 MHz
Bluetooth : 2402 MHz-2480 MHz
RG910:
IS910.1:
GSM 850 : 33.31 dBm
GSM 850 : 33.39 dBm
PCS 1900: 28.41 dBm
PCS 1900: 28.42 dBm
CDMA 850(BC0): 21.83 dBm
CDMA 850(BC0): 21.86 dBm
CDMA 1900(BC1): 21.75 dBm
CDMA 1900(BC1): 21.79 dBm
WCDMA Band 2: 22.88 dBm
WCDMA Band 2: 22.96 dBm
WCDMA Band 5: 22.46 dBm
WCDMA Band 5: 22.52 dBm
LTE Band 7: 22.12 dBm
LTE Band 7: 22.29 dBm
LTE Band 41: 22.15 dBm
LTE Band 41: 22.17 dBm
WLAN: 8.94 dBm
WLAN: 8.97 dBm
Bluetooth(BDR/EDR): 6.62 dBm
Bluetooth(BDR/EDR): 6.69 dBm
BLE: -1.38 dBm
BLE: -1.25 dBm
3.7 VDC Rechargeable Battery
Body Supported
5 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
REFERENCE, STANDARDS, AND GUIDELINES
FCC:
The Report and Order requires routine SAR evaluation prior to equipment authorization of portable
transmitter devices, including portable telephones. For consumer products, the applicable limit is 1.6 mW/g
as recommended by the ANSI/IEEE standard C95.1-1992 [6] for an uncontrolled environment (Paragraph
65). According to the Supplement C of OET Bulletin 65 “Evaluating Compliance with FCC Guide-lines for
Human Exposure to Radio frequency Electromagnetic Fields", released on Jun 29, 2001 by the FCC, the
device should be evaluated at maximum output power (radiated from the antenna) under “worst-case”
conditions for normal or intended use, incorporating normal antenna operating positions, device peak
performance frequencies and positions for maximum RF energy coupling.
This report describes the methodology and results of experiments performed on wireless data terminal. The
objective was to determine if there is RF radiation and if radiation is found, what is the extent of radiation
with respect to safety limits. SAR (Specific Absorption Rate) is the measure of RF exposure determined by
the amount of RF energy absorbed by human body (or its parts) – to determine how the RF energy couples
to the body or head which is a primary health concern for body worn devices. The limit below which the
exposure to RF is considered safe by regulatory bodies in North America is 1.6 mW/g average over 1 gram
of tissue mass.
CE:
The order requires routine SAR evaluation prior to equipment authorization of portable transmitter devices,
including portable telephones. For consumer products, the applicable limit is 2 mW/g as recommended by
EN62209-1 for an uncontrolled environment. According to the Standard, the device should be evaluated at
maximum output power (radiated from the antenna) under “worst-case” conditions for normal or intended
use, incorporating normal antenna operating positions, device peak performance frequencies and positions
for maximum RF energy coupling.
This report describes the methodology and results of experiments performed on wireless data terminal. The
objective was to determine if there is RF radiation and if radiation is found, what is the extent of radiation
with respect to safety limits. SAR (Specific Absorption Rate) is the measure of RF exposure determined by
the amount of RF energy absorbed by human body (or its parts) – to determine how the RF energy couples
to the body or head which is a primary health concern for body worn devices. The limit below which the
exposure to RF is considered safe by regulatory bodies in Europe is 2 mW/g average over 10 gram of tissue
mass.
The test configurations were laid out on a specially designed test fixture to ensure the reproducibility of
measurements. Each configuration was scanned for SAR. Analysis of each scan was carried out to
characterize the above effects in the device.
SAR Evaluation Report
6 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
SAR Limits
FCC Limit
SAR (W/kg)
(General Population /
Uncontrolled Exposure
Environment)
(Occupational /
Controlled Exposure
Environment)
Spatial Average
(averaged over the whole body)
0.08
0.4
Spatial Peak
(averaged over any 1 g of tissue)
1.60
8.0
Spatial Peak
(hands/wrists/feet/ankles
averaged over 10 g)
4.0
20.0
EXPOSURE LIMITS
CE Limit
SAR (W/kg)
EXPOSURE LIMITS
Spatial Average
(averaged over the whole body)
Spatial Peak
(averaged over any 10 g of
tissue)
Spatial Peak
(hands/wrists/feet/ankles
averaged over 10 g)
(General Population /
Uncontrolled Exposure
Environment)
(Occupational /
Controlled Exposure
Environment)
0.08
0.4
2.0
10
4.0
20.0
Population/Uncontrolled Environments are defined as locations where there is the exposure of individual
who have no knowledge or control of their exposure.
Occupational/Controlled Environments are defined as locations where there is exposure that may be
incurred by people who are aware of the potential for exposure (i.e. as a result of employment or
occupation).
General Population/Uncontrolled environments Spatial Peak limit 1.6W/kg (FCC) & 2 W/kg (CE) applied
to the EUT.
SAR Evaluation Report
7 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
FACILITIES
The Test site used by Bay Area Compliance Laboratories Corp. (Dongguan) to collect test data is located
on the No.69 Pulongcun, Puxinhu Industry Area, Tangxia, Dongguan, Guangdong, China.
The test site has been approved by the FCC under the KDB 974614 D01 and is listed in the FCC Public
Access Link (PAL) database, FCC Registration No. : 897218,the FCC Designation No. : CN1220.
The test site has been registered with ISED Canada under ISED Canada Registration Number 3062D.
The test sites and measurement facilities used to collect data are located at:
SAR Lab 1
SAR Evaluation Report
SAR Lab 2
8 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
DESCRIPTION OF TEST SYSTEM
These measurements were performed with the automated near-field scanning system DASY5 from Schmid
& Partner Engineering AG (SPEAG) which is the Fifth generation of the system shown in the figure
hereinafter:
DASY5 System Description
The DASY5 system for performing compliance tests consists of the following items:
SAR Evaluation Report
9 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
A standard high precision 6-axis robot with controller, teach pendant and software. An arm extension
for accommodating the data acquisition electronics (DAE).
An isotropic field probe optimized and calibrated for the targeted measurement.
A data acquisition electronics (DAE) which performs the signal application, signal multiplexing,
AD-conversion, offset measurements, mechanical surface detection, collision detection, etc. The unit is
battery powered with standard or rechargeable batteries. The signal is optically transmitted to the EOC.
The Electro-optical converter (EOC) performs the conversion from optical to electrical signals for the
digital communication to the DAE. To use optical surface detection, a special version of the EOC is
required. The EOC signal is transmitted to the measurement server.
The function of the measurement server is to perform the time critical tasks such as signal filtering,
control of the robot operation and fast movement interrupts.
The Light Beam used is for probe alignment. This improves the (absolute) accuracy of the probe
positioning.
A computer running Win7 professional operating system and the DASY52 software.
Remote control and teach pendant as well as additional circuitry for robot safety such as warning
lamps, etc.
The phantom, the device holder and other accessories according to the targeted measurement.
DASY5 Measurement Server
The DASY5 measurement server is based on a PC/104 CPU
board with a 400MHz Intel ULV Celeron, 128MB chip-disk
and 128MB RAM. The necessary circuits for communication
with the DAE4 (or DAE3) electronics box, as well as the 16
bit AD-converter system for optical detection and digital I/O
interface are contained on the DASY5 I/O board, which is
directly connected to the PC/104 bus of the CPU board.
The measurement server performs all real-time data
evaluation of field measurements and surface detection,
controls robot movements and handles safety operation. The
PC operating system cannot interfere with these time critical
processes. All connections are supervised by a watchdog, and disconnection of any of the cables to the
measurement server will automatically disarm the robot and disable all program-controlled robot
movements. Furthermore, the measurement server is equipped with an expansion port which is reserved for
future applications. Please note that this expansion port does not have a standardized point out, and
therefore only devices provided by SPEAG can be connected. Devices from any other supplier could
seriously damage the measurement server.
Data Acquisition Electronics
The data acquisition electronics (DAE4) consist of a highly sensitive electrometer-grade preamplifier with
auto-zeroing, a channel and gain-switching multiplexer, a fast 16 bit AD-converter and a command decoder
with a control logic unit. Transmission to the measurement server is accomplished through an optical
downlink for data and status information, as well as an optical uplink for commands and the clock.
The mechanical probe mounting device includes two different sensor systems for frontal and sideways
probe contacts. They are used for mechanical surface detection and probe collision detection.
The input impedance of both the DAE4 as well as of the DAE3 box is 200MOhm; the inputs are
symmetrical and floating. Common mode rejection is above 80 dB.
SAR Evaluation Report
10 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
EX3DV4 E-Field Probes
Frequency
10 MHz to > 6 GHz
Linearity: ± 0.2 dB (30 MHz to 6 GHz)
Directivity
± 0.3 dB in TSL (rotation around probe axis)
± 0.5 dB in TSL (rotation normal to probe axis)
Dynamic
Range
10 µW/g to > 100 mW/g
Linearity: ± 0.2 dB (noise: typically < 1 µW/g)
Dimensions
Overall length: 337 mm (Tip: 20 mm)
Tip diameter: 2.5 mm (Body: 12 mm)
Typical distance from probe tip to dipole centers: 1 mm
Application
High precision dosimetric measurements in any exposure scenario
(e.g., very strong gradient fields); the only probe that enables
compliance testing for frequencies up to 6 GHz with precision of
better 30%.
Compatibility
DASY3, DASY4, DASY52 SAR and higher, EASY4/MRI
Calibration Frequency Points for EX3DV4 E-Field Probes SN: 7431 Calibrated: 2017/9/30
Calibration Frequency
Point(MHz)
750 Head
750 Body
900 Head
900 Body
1750 Head
1750 Body
1900 Head
1900 Body
2450 Head
2450 Body
2600 Head
2600 Body
5200 Head
5200 Body
5300 Head
5300 Body
5600 Head
5600 Body
5800 Head
5800 Body
SAR Evaluation Report
Frequency Range(MHz)
Conversion Factor
From
To
650
650
850
850
1650
1650
1850
1850
2350
2350
2550
2550
5100
5100
5250
5250
5490
5490
5700
5700
850
850
1000
1000
1850
1850
2000
2000
2550
2550
2700
2700
5250
5250
5410
5410
5700
5700
5900
5900
10.04
10.11
9.72
9.86
8.36
8.23
8.24
7.86
7.62
7.38
7.31
5.92
5.22
5.6
4.93
4.99
4.4
5.05
4.43
10.04
10.11
9.72
9.86
8.36
8.23
8.24
7.86
7.62
7.38
7.31
5.92
5.22
5.6
4.93
4.99
4.4
5.05
4.43
10.04
10.11
9.72
9.86
8.36
8.23
8.24
7.86
7.62
7.38
7.31
5.92
5.22
5.6
4.93
4.99
4.4
5.05
4.43
11 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
SAM Twin Phantom
The SAM twin phantom is a fiberglass shell phantom with
2mm shell thickness (except the ear region, where shell
thickness
increases to 6 mm). The phantom has three measurement areas:
_ Left Head
_ Right Head
_ Flat phantom
The phantom table for the DASY systems based on the
robots have the size of 100 x 50 x 85 cm (L x W x H).
For easy dislocation these tables have fork lift cut outs at the
bottom.
The bottom plate contains three pairs of bolts for locking the
device holder. The device holder positions are adjusted to the
standard measurement positions in the three sections. Only one device holder is necessary if two phantoms
are used (e.g., for different liquids)
A white cover is provided to cover the phantom during off-periods to prevent water evaporation and
changes in the liquid parameters. Free space scans of devices on top of this phantom cover are possible.
Three reference marks are provided on the phantom counter. These reference marks are used to teach the
absolute phantom position relative to the robot.
Robots
The DASY5 system uses the high precision industrial robot. The robot offers the same features important
for our application:
z High precision (repeatability 0.02mm)
z High reliability (industrial design)
z Low maintenance costs (virtually maintenance free due to direct drive gears; no belt drives)
z Jerk-free straight movements (brushless synchrony motors; no stepper motors)
z Low ELF interference (motor control fields shielded via the closed metallic construction shields)
The above mentioned robots are controlled by the Staubli CS8c robot controllers. All information regarding
the use and maintenance of the robot arm and the robot controller is contained on the CDs delivered along
with the robot. Paper manuals are available upon request direct from Staubli.
Area Scans
Area scans are defined prior to the measurement process being executed with a user defined variable
spacing between each measurement point (integral) allowing low uncertainty measurements to be
conducted. Scans defined for FCC applications utilize a 15mm 2 step integral, with 1.5mm interpolation
used to locate the peak SAR area used for zoom scan assessments.
Where the system identifies multiple SAR peaks (which are within 25% of peak value) the system will
provide the user with the option of assessing each peak location individually for zoom scan averaging.
Zoom Scan (Cube Scan Averaging)
The averaging zoom scan volume utilized in the DASY5 software is in the shape of a cube and the side
dimension of a 1 g or 10 g mass is dependent on the density of the liquid representing the simulated tissue.
A density of 1000 kg/m3 is used to represent the head and body tissue density and not the phantom liquid
density, in order to be consistent with the definition of the liquid dielectric properties, i.e. the side length of
the 1g cube is 10mm,with the side length of the 10g cube is 21.5mm.
SAR Evaluation Report
12 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
When the cube intersects with the surface of the phantom, it is oriented so that 3 vertices touch the surface
of the shell or the center of a face is tangent to the surface. The face of the cube closest to the surface is
modified in order to conform to the tangent surface.
The zoom scan integer steps can be user defined so as to reduce uncertainty, but normal practice for typical
test applications (including FCC) utilize a physical step of 7 x7 x 7 (5mmx5mmx5mm) providing a volume
of 30 mm in the X & Y & Z axis.
Tissue Dielectric Parameters for Head and Body Phantoms
The head tissue dielectric parameters recommended by the IEEE SCC-34/SC-2 in P1528 have been
incorporated in the following table. These head parameters are derived from planar layer models simulating
the highest expected SAR for the dielectric properties and tissue thickness variations in a human head.
Other head and body tissue parameters that have not been specified in P1528 are derived from the tissue
dielectric parameters computed from the 4-Cole-Cole equations described in Reference [12] and
extrapolated according to the head parameters specified in P1528.
Recommended Tissue Dielectric Parameters for Head and Body
Head Tissue
Body Tissue
Frequency
(MHz)
εr
Ơ (S/m)
εr
Ơ (S/m)
150
52.3
0.76
61.9
0.80
300
45.3
0.87
58.2
0.92
450
43.5
0.87
56.7
0.94
835
41.5
0.90
55.2
0.97
900
41.5
0.97
55.0
1.05
915
41.5
0.98
55.0
1.06
1450
40.5
1.20
54.0
1.30
1610
40.3
1.29
53.8
1.40
1800-2000
40.0
1.40
53.3
1.52
2450
39.2
1.80
52.7
1.95
3000
38.5
2.40
52.0
2.73
5800
35.3
5.27
48.2
6.00
SAR Evaluation Report
13 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
EQUIPMENT LIST AND CALIBRATION
Equipments List & Calibration Information
Equipment
Model
S/N
Calibration
Date
Calibration
Due Date
DASY5 Test Software
DASY52.8
N/A
NCR
NCR
DASY5 Measurement Server
DASY5 4.5.12
1567
NCR
NCR
Data Acquisition Electronics
DAE4
772
2017/10/9
2018/10/8
E-Field Probe
EX3DV4
7431
2017/9/30
2018/9/29
Mounting Device
MD4HHTV5
BJPCTC0152
NCR
NCR
Twin SAM
Twin SAM V5.0
1412
NCR
NCR
Dipole, 750 MHz
D750V3
1167
2016/11/8
2019/11/7
Dipole, 1900 MHz
D1900V2
543
2016/10/25
2019/10/24
Dipole,2450 MHz
D2450V2
971
2015/7/8
2018/7/8
Dipole, 2600 MHz
D2600V2
1132
2016/11/10
2019/11/9
Simulated Tissue 750 MHz Body
TS-750-B
1710075002
Each Time
Simulated Tissue 1900 MHz Body
TS-1900-B
1709190002
Each Time
Simulated Tissue 2450 MHz Body
TS-2450-B
1703245002
Each Time
Simulated Tissue 2600 MHz Body
TS-2600-B
1709260002
Network Analyzer
8753C
3033A02857
2017/8/31
2018/8/31
Dielectric assessment kit
1253
SM DAK 040 CA
NCR
NCR
ESG Series Signal Generator
E4422B
MY41000355
2017/12/14
2018/12/14
Power Meter
EPM-441A
GB37481494
2017/12/11
2018/12/11
Power Amplifier
ZVA-183-S+
5969001149
NCR
NCR
Directional Coupler
488Z
N/A
NCR
NCR
Attenuator
20dB, 100W
N/A
NCR
NCR
Attenuator
R&S, universal Radio
Communication Tester
Wireless communication tester
Wideband Radio Communication
Tester
3dB, 150W
N/A
NCR
NCR
CMU200
109 038
2017/7/21
2018/7/21
E5515C
MY48367501
2017/12/11
2018/12/11
CMW500
1201.0002K50
2017/8/31
2018/8/31
SAR Evaluation Report
Each Time
14 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
SAR MEASUREMENT SYSTEM VERIFICATION
Liquid Verification
Liquid Verification Results
Frequency
(MHz)
Liquid Verification Setup Block Diagram
Liquid Type
Liquid
Parameter
εr
750
Simulated Tissue 750 MHz Body 57.124
824.2
Simulated Tissue 750 MHz Body 57.283
824.7
Simulated Tissue 750 MHz Body 57.418
826.4
Simulated Tissue 750 MHz Body 57.376
836.52
Simulated Tissue 750 MHz Body 57.172
836.6
Simulated Tissue 750 MHz Body 56.996
846.6
Simulated Tissue 750 MHz Body 56.877
848.31
Simulated Tissue 750 MHz Body 56.846
848.8
Simulated Tissue 750 MHz Body 56.835
*Liquid Verification above was performed on 2018/06/10.
Frequency
(MHz)
Liquid Type
Liquid
Parameter
εr
1850.2
Simulated Tissue 1900 MHz Body 54.598
1851.25
Simulated Tissue 1900 MHz Body 54.592
1852.4
Simulated Tissue 1900 MHz Body 54.582
1880
Simulated Tissue 1900 MHz Body 54.206
1900
Simulated Tissue 1900 MHz Body 54.173
1907.6
Simulated Tissue 1900 MHz Body 54.135
1908.75
Simulated Tissue 1900 MHz Body 54.112
1909.8
Simulated Tissue 1900 MHz Body 54.101
*Liquid Verification above was performed on 2018/06/09.
SAR Evaluation Report
Ơ
(S/m)
0.932
0.944
0.947
0.953
0.961
0.961
0.963
0.967
0.973
Ơ
(S/m)
1.454
1.461
1.468
1.488
1.515
1.516
1.521
1.531
Delta
(%)
Target Value
εr
55.53
55.24
55.24
55.23
55.2
55.2
55.16
55.16
55.16
Ơ
(S/m)
0.96
0.97
0.97
0.97
0.97
0.97
0.98
0.99
0.99
Δεr
2.87
3.7
3.94
3.89
3.57
3.25
3.11
3.06
3.04
Target
Value
εr
53.3
53.3
53.3
53.3
53.3
53.3
53.3
53.3
Ơ
(S/m)
1.52
1.52
1.52
1.52
1.52
1.52
1.52
1.52
ΔƠ
(S/m)
-2.92
-2.68
-2.37
-1.75
-0.93
-0.93
-1.73
-2.32
-1.72
Delta
(%)
Δεr
2.44
2.42
2.41
1.7
1.64
1.57
1.52
1.5
ΔƠ
(S/m)
-4.34
-3.88
-3.42
-2.11
-0.33
-0.26
0.07
0.72
Tolerance
(%)
±5
±5
±5
±5
±5
±5
±5
±5
±5
Tolerance
(%)
±5
±5
±5
±5
±5
±5
±5
±5
15 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Frequency
(MHz)
Liquid Type
Report No.: RSZ180529003-20A
Liquid
Parameter
εr
2402
Simulated Tissue 2450 MHz Body 54.424
2412
Simulated Tissue 2450 MHz Body 54.393
2431
Simulated Tissue 2450 MHz Body 54.275
2441
Simulated Tissue 2450 MHz Body 54.187
2442
Simulated Tissue 2450 MHz Body 54.186
2450
Simulated Tissue 2450 MHz Body 53.929
2462
Simulated Tissue 2450 MHz Body 53.806
2480
Simulated Tissue 2450 MHz Body 53.798
2510
Simulated Tissue 2450 MHz Body 53.677
2535
Simulated Tissue 2450 MHz Body 53.526
*Liquid Verification above was performed on 2018/06/13.
Frequency
(MHz)
Liquid Type
Liquid
Parameter
εr
2560
Simulated Tissue 2600 MHz Body 53.54
2565
Simulated Tissue 2600 MHz Body 53.368
2605
Simulated Tissue 2600 MHz Body 53.352
2600
Simulated Tissue 2600 MHz Body 53.349
2645
Simulated Tissue 2600 MHz Body 53.324
*Liquid Verification above was performed on 2018/06/12.
SAR Evaluation Report
Ơ
(S/m)
1.866
1.905
1.918
1.931
1.933
1.952
1.971
1.982
1.995
2.058
Ơ
(S/m)
2.122
2.136
2.145
2.151
2.165
Delta
(%)
Target Value
εr
52.76
52.75
52.73
52.71
52.71
52.7
52.68
52.66
52.62
52.59
Ơ
(S/m)
1.9
1.91
1.93
1.94
1.94
1.95
1.97
1.99
2.04
2.07
Δεr
3.15
3.11
2.93
2.8
2.8
2.33
2.14
2.16
2.01
1.78
Delta
(%)
Target Value
εr
52.56
52.55
52.5
52.51
52.45
Ơ
(S/m)
2.11
2.11
2.17
2.16
2.23
ΔƠ
(S/m)
-1.79
-0.26
-0.62
-0.46
-0.36
0.1
0.05
-0.4
-2.21
-0.58
Δεr
1.86
1.56
1.62
1.6
1.67
ΔƠ
(S/m)
0.57
1.23
-1.15
-0.42
-2.91
Tolerance
(%)
±5
±5
±5
±5
±5
±5
±5
±5
±5
±5
Tolerance
(%)
±5
±5
±5
±5
±5
16 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
System Accuracy Verification
Prior to the assessment, the system validation kit was used to test whether the system was operating within
its specifications of ±10%. The validation results are tabulated below. And also the corresponding SAR plot
is attached as well in the SAR plots files.
The spacing distances in the System Verification Setup Block Diagram is given by the following:
a)
s = 15 mm ± 0,2 mm for 300 MHz ≤ f ≤ 1 000 MHz;
b) s = 10 mm ± 0,2 mm for 1 000 MHz < f ≤ 3 000 MHz;
c)
s = 10 mm ± 0,2 mm for 3 000 MHz < f ≤ 6 000 MHz.
System Verification Setup Block Diagram
System Accuracy Check Results
Date
Frequency
Band
Liquid Type
Input
Power
(mW)
Measured
SAR
(W/kg)
Normalized
to 1W
(W/kg)
Target
Value
(W/kg)
Delta
(%)
Tolerance
(%)
2018/06/10
750 MHz
750MHz Body
100
1g
0.843
8.43
8.58
-1.75
±10
2018/06/09
1900 MHz
1900MHz Body
100
1g
4.12
41.2
41.1
0.24
±10
2018/06/13
2450 MHz
2450MHz Body
100
1g
5.07
50.7
50.6
0.20
±10
2018/06/12
2600 MHz
2600MHz Body
100
1g
5.33
53.3
53.9
-1.11
±10
*The SAR values above are normalized to 1 Watt forward power.
SAR Evaluation Report
17 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
SAR SYSTEM VALIDATION DATA
System Performance 750 MHz Body
DUT: D750V3; Type: 750 MHz; Serial: 1167
Communication System: CW; Frequency: 750 MHz; Duty Cycle: 1:1
Medium parameters used: f = 750 MHz; σ = 0.932 S/m; εr = 57.124; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY5 Configuration:
•
•
•
•
•
Probe: EX3DV4 - SN7431; ConvF(10.11, 10.11, 10.11); Calibrated: 2017/9/30;
Sensor-Surface: 1.4mm (Mechanical Surface Detection)
Electronics: DAE4 Sn772;Calibrated: 2017/10/9
Phantom: Twin SAM; Type: Twin SAM V5.0; Serial: 1412
Measurement SW: DASY52, Version 52.8 (8);
Area Scan (41x101x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm
Maximum value of SAR (interpolated) = 1.08 W/kg
Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm
Reference Value = 31.70 V/m; Power Drift = -0.16 dB
Peak SAR (extrapolated) = 1.18 W/kg
SAR(1 g) = 0.843 W/kg; SAR(10 g) = 0.559 W/kg
Maximum value of SAR (measured) = 1.09 W/kg
0 dB = 1.09 W/kg = 0.37 dBW/kg
SAR Evaluation Report
18 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
System Performance 1900 MHz Body
DUT: D1900V2; Type: 1900 MHz; Serial: 543
Communication System: CW; Frequency: 1900 MHz; Duty Cycle: 1:1
Medium parameters used: f = 1900 MHz; σ = 1.515 S/m; εr = 54.173; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY5 Configuration:
•
•
•
•
•
Probe: EX3DV4 - SN7431; ConvF(8, 8, 8); Calibrated: 2017/9/30;
Sensor-Surface: 1.4mm (Mechanical Surface Detection)
Electronics: DAE4 Sn772;Calibrated: 2017/10/9
Phantom: Twin SAM; Type: Twin SAM V5.0; Serial: 1412
Measurement SW: DASY52, Version 52.8 (8);
Area Scan (41x51x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm
Maximum value of SAR (interpolated) = 6.73 W/kg
Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm
Reference Value = 54.57 V/m; Power Drift = -0.11 dB
Peak SAR (extrapolated) = 7.82 W/kg
SAR(1 g) = 4.12 W/kg; SAR(10 g) = 2.16 W/kg
Maximum value of SAR (measured) = 6.44 W/kg
0 dB = 6.44 W/kg = 8.09 dBW/kg
SAR Evaluation Report
19 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
System Performance 2450MHz Body
DUT: D2450V2; Type: 2450 MHz; Serial: 971
Communication System:CW; Frequency: 2450 MHz; Duty Cycle: 1:1
Medium parameters used: f = 2450 MHz; σ = 1.952 S/m; εr = 53.929; ρ = 1000 kg/m3
Phantom section: Flat Section
D ASY5 Configuration:
•
•
•
•
•
Probe: EX3DV4 - SN7431; ConvF(7.62, 7.62, 7.62); Calibrated: 2017/9/30;
Sensor-Surface: 1.4mm (Mechanical Surface Detection)
Electronics: DAE4 Sn772;Calibrated: 2017/10/9
Phantom: Twin SAM; Type: Twin SAM V5.0; Serial: 1412
Measurement SW: DASY52, Version 52.8 (8);
Area Scan (51x61x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm
Maximum value of SAR (interpolated) = 9.58 W/kg
Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm
Reference Value = 54.75 V/m; Power Drift = -0.04 dB
Peak SAR (extrapolated) = 11.3 W/kg
SAR(1 g) = 5.07 W/kg; SAR(10 g) = 2.30 W/kg
Maximum value of SAR (measured) = 8.89 W/kg
0 dB = 8.89 W/kg = 9.49 dBW/kg
SAR Evaluation Report
20 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
System Performance 2600 MHz Body
DUT: D2600V2; Type: 2600 MHz; Serial: 1132
Communication System: CW; Frequency: 2600 MHz; Duty Cycle: 1:1
Medium parameters used: f = 2600 MHz; σ = 2.151 S/m; εr = 53.349; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY5 Configuration:
•
Probe: EX3DV4 - SN7431; ConvF(7.31, 7.31, 7.31); Calibrated: 2017/9/30;
•
Sensor-Surface: 1.4mm (Mechanical Surface Detection)
•
Electronics: DAE4 Sn772;Calibrated: 2017/10/9
•
Phantom: Twin SAM; Type: Twin SAM V5.0; Serial: 1412
•
Measurement SW: DASY52, Version 52.8 (8);
Area Scan (51x61x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm
Maximum value of SAR (interpolated) = 10.3 W/kg
Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm
Reference Value = 56.81 V/m; Power Drift = 0.02 dB
Peak SAR (extrapolated) = 11.5 W/kg
SAR(1 g) = 5.33 W/kg; SAR(10 g) = 2.52 W/kg
Maximum value of SAR (measured) = 9.54 W/kg
0 dB = 9.54 W/kg = 9.80 dBW/kg
SAR Evaluation Report
21 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
EUT TEST STRATEGY AND METHODOLOGY
Test Positions for Device Operating Next to a Person’s Ear
This category includes most wireless handsets with fixed, retractable or internal antennas located toward
the top half of the device, with or without a foldout, sliding or similar keypad cover. The handset should
have its earpiece located within the upper ¼ of the device, either along the centerline or off-centered, as
perceived by its users. This type of handset should be positioned in a normal operating position with the
“test device reference point” located along the “vertical centerline” on the front of the device aligned to the
“ear reference point”. The “test device reference point” should be located at the same level as the center
of the earpiece region. The “vertical centerline” should bisect the front surface of the handset at its top
and bottom edges. A “ear reference point” is located on the outer surface of the head phantom on each ear
spacer. It is located 1.5 cm above the center of the ear canal entrance in the “phantom reference plane”
defined by the three lines joining the center of each “ear reference point” (left and right) and the tip of the
mouth.
A handset should be initially positioned with the earpiece region pressed against the ear spacer of a head
phantom. For the SCC-34/SC-2 head phantom, the device should be positioned parallel to the “N-F” line
defined along the base of the ear spacer that contains the “ear reference point”. For interim head
phantoms, the device should be positioned parallel to the cheek for maximum RF energy coupling. The
“test device reference point” is aligned to the “ear reference point” on the head phantom and the “vertical
centerline” is aligned to the “phantom reference plane”. This is called the “initial ear position”. While
maintaining these three alignments, the body of the handset is gradually adjusted to each of the following
positions for evaluating SAR:
LE ER
15
mm
EE
ERP - ear reference
i t- entrance to ear
EEP
SAR Evaluation Report
22 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
Cheek/Touch Position
The device is brought toward the mouth of the head phantom by pivoting against the “ear reference point”
or along the “N-F” line for the SCC-34/SC-2 head phantom.
This test position is established:
When any point on the display, keypad or mouthpiece portions of the handset is in contact
with the phantom.
(or) When any portion of a foldout, sliding or similar keypad cover opened to its intended
self-adjusting normal use position is in contact with the cheek or mouth of the phantom.
For existing head phantoms – when the handset loses contact with the phantom at the pivoting point,
rotation should continue until the device touches the cheek of the phantom or breaks its last contact
from the ear spacer.
Cheek /Touch Position
Ear/Tilt Position
With the handset aligned in the “Cheek/Touch Position”:
1) If the earpiece of the handset is not in full contact with the phantom’s ear spacer (in the “Cheek/Touch
position”) and the peak SAR location for the “Cheek/Touch” position is located at the ear spacer region or
corresponds to the earpiece region of the handset, the device should be returned to the “initial ear position”
by rotating it away from the mouth until the earpiece is in full contact with the ear spacer.
2) (otherwise) The handset should be moved (translated) away from the cheek perpendicular to the line
passes through both “ear reference points” (note: one of these ear reference points may not physically exist
on a split head model) for approximate 2-3 cm. While it is in this position, the device handset is tilted away
from the mouth with respect to the “test device reference point” until the inside angle between the vertical
centerline on the front surface of the phone and the horizontal line passing through the ear reference point is
by 15 80°. After the tilt, it is then moved (translated) back toward the head perpendicular to the line passes
through both “ear reference points” until the device touches the phantom or the ear spacer. If the antenna
touches the head first, the positioning process should be repeated with a tilt angle less than 15° so that the
device and its antenna would touch the phantom simultaneously. This test position may require a device
holder or positioner to achieve the translation and tilting with acceptable positioning repeatability.
If a device is also designed to transmit with its keypad cover closed for operating in the head position, such
positions should also be considered in the SAR evaluation. The device should be tested on the left and right
side of the head phantom in the “Cheek/Touch” and “Ear/Tilt” positions. When applicable, each
configuration should be tested with the antenna in its fully extended and fully retracted positions. These test
configurations should be tested at the high, middle and low frequency channels of each operating mode; for
example, AMPS, CDMA, and TDMA. If the SAR measured at the middle channel for each test
configuration (left, right, Cheek/Touch, Tilt/Ear, extended and retracted) is at least 2.0 dB lower than the
SAR limit, testing at the high and low channels is optional for such test configuration(s). If the transmission
band of the test device is less than 10 MHz, testing at the high and low frequency channels is optional.
SAR Evaluation Report
23 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
Ear /Tilt 15o Position
Test positions for body-worn and other configurations
Body-worn operating configurations should be tested with the belt-clips and holsters attached to the device
and positioned against a flat phantom in normal use configurations. Devices with a headset output should
be tested with a headset connected to the device. When multiple accessories that do not contain metallic
components are supplied with the device, the device may be tested with only the accessory that dictates the
closest spacing to the body. When multiple accessories that contain metallic components are supplied with
the device, the device must be tested with each accessory that contains a unique metallic component. If
multiple accessories share an identical metallic component (e.g., the same metallic belt-clip used with
different holsters with no other metallic components), only the accessory that dictates the closest spacing to
the body must be tested.
Body-worn accessories may not always be supplied or available as options for some devices that are
intended to be authorized for body-worn use. A separation distance of 1.5 cm between the back of the
device and a flat phantom is recommended for testing body-worn SAR compliance under such
circumstances. Other separation distances may be used, but they should not exceed 2.5 cm. In these cases,
the device may use body-worn accessories that provide a separation distance greater than that tested for the
device provided however that the accessory contains no metallic components.
Test Distance for SAR Evaluation
For this case the EUT(Equipment Under Test) is set 0mm away from the phantom, the test distance is 0mm.
SAR Evaluation Report
24 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
SAR Evaluation Procedure
The evaluation was performed with the following procedure:
Step 1: Measurement of the SAR value at a fixed location above the ear point or central position was
used as a reference value for assessing the power drop. The SAR at this point is measured at the start
of the test and then again at the end of the testing.
Step 2: The SAR distribution at the exposed side of the head was measured at a distance of 4 mm
from the inner surface of the shell. The area covered the entire dimension of the head or radiating
structures of the EUT, the horizontal grid spacing was 15 mm x 15 mm, and the SAR distribution was
determined by integrated grid of 1.5mm x 1.5mm. Based on these data, the area of the maximum
absorption was determined by spline interpolation. The first Area Scan covers the entire dimension of
the EUT to ensure that the hotspot was correctly identified.
Step 3: Around this point, a volume of 30 mm x 30 mm x 30 mm was assessed by measuring 7x 7 x 7
points. On the basis of this data set, the spatial peak SAR value was evaluated under the following
procedure:
1) The data at the surface were extrapolated, since the center of the dipoles is 1.2 mm away
from the tip of the probe and the distance between the surface and the lowest measuring point is
1.3 mm. The extrapolation was based on a least square algorithm. A polynomial of the fourth
order was calculated through the points in z-axes. This polynomial was then used to evaluate the
points between the surface and the probe tip.
2) The maximum interpolated value was searched with a straightforward algorithm. Around this
maximum the SAR values averaged over the spatial volumes (1 g or 10 g) were computed by the
3D-Spline interpolation algorithm. The 3D-Spline is composed of three one dimensional splines
with the “Not a knot"-condition (in x, y and z-directions). The volume was integrated with the
trapezoidal-algorithm. One thousand points (10 x 10 x 10) were interpolated to calculate the
averages.
All neighboring volumes were evaluated until no neighboring volume with a higher average
value was found.
Step 4: Re-measurement of the SAR value at the same location as in Step 1. If the value changed by
more than 5%, the evaluation was repeated.
SAR Evaluation Report
25 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
CONDUCTED OUTPUT POWER MEASUREMENT
Provision Applicable
The measured peak output power should be greater and within 5% than EMI measurement.
Test Procedure
The RF output of the transmitter was connected to the input of the EMI Test Receiver through Connector.
EUT
Connector
EMI Test
Receiver
Wireless Communication Test
Set
(R&S CMU200/
E5515C/CMW500)
GSM/WCDMA/LTE
Radio Configuration
The power measurement was configured by the Wireless Communication Test Set.
GSM/GPRS/EGPRS
Function: Menu select > GSM Mobile Station > GSM 850/1900
Press Connection control to choose the different menus
Press RESET > choose all the reset all settings
Connection Press Signal Off to turn off the signal and change settings
Network Support > GSM + GPRS or GSM + EGSM
Main Service > Packet Data
Service selection > Test Mode A – Auto Slot Config. off
MS Signal Press Slot Config Bottom on the right twice to select and change the number of time slots and
power setting
> Slot configuration > Uplink/Gamma
> 33 dBm for GPRS 850
> 30 dBm for GPRS 1900
> 27 dBm for EGPRS 850
> 26 dBm for EGPRS 1900
BS Signal Enter the same channel number for TCH channel (test channel) and BCCH channel
Frequency Offset > + 0 Hz
Mode > BCCH and TCH
BCCH Level > -85 dBm (May need to adjust if link is not stabe)
BCCH Channel > choose desire test channel [Enter the same channel number for TCH channel (test
channel) and BCCH channel]
Channel Type > Off
P0 > 4 dB
Slot Config >Unchanged (if already set under MS signal)
TCH > choose desired test channel
Hopping > Off
Main Timeslot > 3
Network Coding Scheme > CS4 (GPRS) and MCS5 (EGPRS)
Bit Stream >2E9-1 PSR Bit Stream
AF/RF Enter appropriate offsets for Ext. Att. Output and Ext. Att. Input
Connection Press Signal on to turn on the signal and change settings
SAR Evaluation Report
26 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
CDMA 1x RTT
Maximum output power is verified on the high, middle and low channels according to procedures in section
4.4.5.2 of 3GPP2 C.S0011/TIA-98-E. Steps 3 and 4 are measured using Loopback Service Option SO55
with power control bits in “All Up” condition. Step 10 is measured using TDSO/SO32 with power control
bits in the “Bits Hold” condition (i.e. alternative Up/Down Bits).
EVDO
Maximum output power is verified on the high, middle and low channels according to procedures in section
3.1.2.3.4 of 3GPP2 C.S0033-0/TIA-866 for Rev. 0, section 4.3.4 of 3GPP2 C.S0033-A for Rev. A.
Maximum output power is measured for Rev. 0 and Rev. A in Subtype 0/1 and Subtype 2 Physical Layer
configurations, respectively.
SAR Evaluation Report
27 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
WCDMA Release 99
The following tests were conducted according to the test requirements outlines in section 5.2 of the 3GPP
TS34.121-1 specification. The EUT has a nominal maximum output power of 24dBm (+1.7/-3.7).
WCDMA
General Settings
Loopback Mode
Test Mode 1
Rel99 RMC
12.2kbps RMC
Power Control
Algorithm
Algorithm2
βc/βd
8/15
HSDPA
The following tests were conducted according to the test requirements outlines in section 5.2 of the 3GPP
TS34.121-1 specification.
WCDMA
General
Settings
HSDPA
Specific
Settings
Mode
Subset
Loopback Mode
Rel99 RMC
HSDPA FRC
Power Control
Algorithm
βc
βd
βd(SF)
βc/βd
βhs
MPR(dB)
DACK
DNAK
DCQI
Ack-Nack repetition
factor
CQI Feedback
CQI Repetition Factor
Ahs=βhs/ βc
SAR Evaluation Report
HSDPA
HSDPA
HSDPA
Test Mode 1
12.2kbps RMC
H-Set1
HSDPA
Algorithm2
2/15
15/15
12/15
15/15
2/15
4/15
12/15
24/15
15/15
8/15
64
15/8
30/15
0.5
15/15
4/15
15/4
30/15
0.5
4ms
30/15
28 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
HSUPA
The following tests were conducted according to the test requirements outlines in section 5.2 of the 3GPP
TS34.121-1 specification.
WCDMA
General
Settings
HSDPA
Specific
Settings
Mode
Subset
Loopback Mode
Rel99 RMC
HSDPA FRC
HSUPA Test
Power Control
Algorithm
βc
βd
βec
βc / βd
βhs
CM(dB)
MPR(dB)
DACK
DNAK
DCQI
Ack-Nack
repetition factor
CQI Feedback
CQI Repetition
Factor
Ahs=βhs/ βc
DE-DPCCH
DHARQ
AG Index
ETFCI
Associated Max
UL Data Rate kbps
HSUPA
Specific
Settings
Reference E_FCls
SAR Evaluation Report
HSUPA
HSUPA
HSUPA
HSUPA
Test Mode 1
12.2kbps RMC
H-Set1
HSUPA Loopback
HSUPA
Algorithm2
11/15
15/15
209/225
11/15
22/15
1.0
6/15
15/15
12/15
6/15
12/15
3.0
15/15
9/15
30/15
15/9
30/15
2.0
2/15
15/15
2/15
2/15
4/15
3.0
15/15
5/15
5/15
1.0
17
71
21
81
205.8
308.9
4ms
20
75
12
67
30/15
15
92
242.1
174.9
482.8
E-TFCI 11 E
E-TFCI PO 4
E-TFCI 67
E-TFCI PO 18
E-TFCI 71
E-TFCI PO23
E-TFCI 75
E-TFCI PO26
E-TFCI 81
E-TFCI PO 27
E-TFCI
11
E-TFCI
PO4
E-TFCI
92
E-TFCI
PO 18
E-TFCI 11 E
E-TFCI PO 4
E-TFCI 67
E-TFCI PO 18
E-TFCI 71
E-TFCI PO23
E-TFCI 75
E-TFCI PO26
E-TFCI 81
E-TFCI PO 27
29 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
HSPA+
The following tests were conducted according to the test requirements in Table C.11.1.4 of 3GPP TS
34.121-1
SAR Evaluation Report
30 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
FDD-LTE
For UE Power Class 1 and 3, the allowed Maximum Power Reduction (MPR) for the maximum output
power in Table 6.2.2-1due to higher order modulation and transmit bandwidth configuration (resource
blocks) is specified in Table 6.2.3-1.
For UE Power Class 1 and 3 the specific requirements and identified sub clauses are specified in Table
6.2.4-1 along with the allowed A-MPR values that may be used to meet these requirements. The allowed
A-MPR values specified below in Table 6.2.4.-1 to 6.2.4-15 are in addition to the allowed MPR
requirements specified in sub clause 6.2.3.
SAR Evaluation Report
31 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
TDD-LTE
SAR Evaluation Report
32 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
Maximum Target Output Power
Max Target Power(dBm)
Mode/Band
GSM 850
GPRS 1 TX Slot
GPRS 2 TX Slot
GPRS 3 TX Slot
GPRS 4 TX Slot
EDGE 1 TX Slot
EDGE 2 TX Slot
EDGE 3 TX Slot
EDGE 4 TX Slot
PCS 1900
GPRS 1 TX Slot
GPRS 2 TX Slot
GPRS 3 TX Slot
GPRS 4 TX Slot
EDGE 1 TX Slot
EDGE 2 TX Slot
EDGE 3 TX Slot
EDGE 4 TX Slot
CDMA 850(CDMA 1x RTT)
CDMA 850(EVDO)
CDMA 1900(CDMA 1x RTT)
CDMA 1900(EVDO)
WCDMA Band 2
HSDPA
HSUPA
HSPA+
WCDMA Band 5
HSDPA
HSUPA
HSPA+
LTE Band 7
LTE Band 41
WLAN(802.11b)
WLAN(802.11g)
WLAN(802.11n HT20)
WLAN(802.11n HT40)
Bluetooth BDR/EDR
Bluetooth LE
SAR Evaluation Report
Low
33.5
33.5
33.2
30.9
28
27.5
26
24.6
23.4
28.5
28.5
27.6
26.4
24.3
25.5
24.7
23.7
22.7
22
21.8
21.8
21.9
23.1
22
21.5
21.1
22.6
22.6
22.1
21.8
22.3
22.2
-1
Channel
Middle
33.5
33.5
33.2
30.9
28
27.5
26
24.6
23.4
28.5
28.5
27.6
26.4
24.3
25.5
24.7
23.7
22.7
22
21.8
21.8
21.9
23.1
22
21.5
21.1
22.6
22.6
22.1
21.8
22.3
22.2
-1
High
33.5
33.5
33.2
30.9
28
27.5
26
24.6
23.4
28.5
28.5
27.6
26.4
24.3
25.5
24.7
23.7
22.7
22
21.8
21.8
21.9
23.1
22
21.5
21.1
22.6
22.6
22.1
21.8
22.3
22.2
-5
33 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
IS910.1 Test Results:
GSM:
Band
Frequency
RF Output Power
(MHz)
(dBm)
128
824.2
33.31
190
836.6
33.19
251
848.8
33.17
512
1850.2
28.29
661
1880
28.42
810
1909.8
28.40
Channel No.
GSM 850
PCS 1900
GPRS:
Band
GSM 850
PCS 1900
RF Output Power (dBm)
Channel
No.
Frequency
(MHz)
1 slot
2 slots
3 slots
4 slots
128
824.2
33.39
33.13
30.82
27.93
190
836.6
33.23
33.02
30.36
27.61
251
848.8
33.05
32.97
30.27
27.39
512
1850.2
28.33
26.55
26.29
22.68
661
1880
28.42
27.51
26.28
23.89
810
1909.8
28.34
27.45
26.24
24.17
Channel
No.
Frequency
(MHz)
1 slot
2 slots
3 slots
4 slots
128
824.2
27.40
25.86
24.49
23.26
190
836.6
26.97
25.41
24.18
22.83
251
848.8
26.85
25.08
23.99
22.71
512
1850.2
24.54
23.36
23.36
21.21
661
1880
25.22
24.24
23.44
22.23
810
1909.8
25.44
24.57
23.62
22.64
EDGE:
Band
GSM 850
PCS 1900
RF Output Power (dBm)
For SAR, the time based average power is relevant, the difference in between depends on the duty cycle of
the TDMA signal.
Number of Time slot
Duty Cycle
Time based Ave. power compared to
slotted Ave. power
Crest Factor
1:8
1:4
1:2.66
1:2
-9 dB
-6 dB
-4.25 dB
-3 dB
2.66
SAR Evaluation Report
34 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
The time based average power for GPRS
Band
Time based average Power (dBm)
Channel
No.
Frequency
(MHz)
1 slot
2 slot
3 slots
4 slots
128
824.2
24.39
27.13
26.57
24.93
190
836.6
24.23
27.02
26.11
24.61
251
848.8
24.05
26.97
26.02
24.39
512
1850.2
19.33
20.55
22.04
19.68
661
1880
19.42
21.51
22.03
20.89
810
1909.8
19.34
21.45
21.99
21.17
GSM 850
PCS 1900
The time based average power for EDGE
Band
Frequency
(MHz)
1 slot
2 slot
3 slots
4 slots
128
824.2
18.4
19.86
20.24
20.26
190
836.6
17.97
19.41
19.93
19.83
251
848.8
17.85
19.08
19.74
19.71
512
1850.2
15.54
17.36
19.11
18.21
661
1880
16.22
18.24
19.19
19.23
810
1909.8
16.44
18.57
19.37
19.64
GSM 850
PCS 1900
Note:
Time based average Power (dBm)
Channel
No.
1. Rohde & Schwarz Radio Communication Tester (CMU200) was used for the measurement of GSM peak
and average output power for active timeslots.
2 .For GPRS, 1, 2, 3 and 4 timeslots has been activated separately with power level 3(850 MHz band) and
3(1900 MHz band).
3. According to KDB941225D01-SAR for EGPRS mode are not required when the source-based
time-averaged output power for data mode is lower than that in the normal GPRS mode.
CDMA 1x RTT
Band
BC0
BC1
RF Output Power
(dBm)
RC3+SO32
RC3+SO55
(FCH)
21.62
21.25
Channel
Frequency
No.
(MHz)
1013
824.70
21.35
384
836.52
21.79
21.86
21.64
21.49
777
848.31
21.68
21.69
21.59
21.62
25
1851.25
21.24
21.34
21.17
21.42
600
1880
21.43
21.65
21.39
21.53
1175
1908.75
21.56
21.37
21.54
21.55
SAR Evaluation Report
RC1+SO55
RC3+SO32
(SCH)
21.35
35 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
EVDO
Band
Channel No.
BC0
BC1
Frequency
(MHz)
RF Output Power
(dBm)
RTAP 153.6kbps
RETAP 4096pbs
Subtype 0
Subtype 2
21.71
21.26
1013
824.7
384
836.52
21.42
21.23
777
848.31
21.52
21.45
25
1851.25
21.79
21.72
600
1880
21.64
21.65
1175
1908.75
21.56
21.52
WCDMA:
Results (12.2kbps RMC)
Frequency
Band
WCDMA Band 2
WCDMA Band 5
(MHz)
RF Output Power
(dBm)
1852.4
22.59
1880
22.64
1907.6
22.96
826.4
22.49
836.6
22.52
846.6
22.45
Results (HSDPA)
Band
WCDMA Band 2
WCDMA Band 5
SAR Evaluation Report
RF Output Power (dBm)
Frequency
(MHz)
Subset 1
Subset 2
Subset 3
Subset 4
1852.4
20.85
20.96
20.72
20.96
1880
21.22
21.17
21.13
21.32
1907.6
21.69
21.88
21.58
21.83
826.4
22.45
22.26
22.36
22.19
836.6
22.33
22.29
22.39
22.26
846.6
22.32
22.30
22.46
22.29
36 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
Results (HSUPA)
Band
WCDMA Band 2
WCDMA Band 5
RF Output Power (dBm)
Frequency
(MHz)
Subset 1
Subset 2
Subset 3
Subset 4
Subset 5
1852.4
20.52
20.58
20.56
20.49
20.60
1880
20.68
20.50
20.80
20.54
20.58
1907.6
21.10
21.23
21.18
21.18
21.21
826.4
21.81
21.67
21.89
21.64
21.94
836.6
21.90
21.80
21.94
21.74
21.96
846.6
21.86
21.87
21.94
21.70
21.81
Results (HSPA+)
Band
WCDMA Band 2
WCDMA Band 5
Frequency
(MHz)
RF Output Power
(dBm)
1852.4
20.42
1880
20.55
1907.6
21.08
826.4
21.61
836.6
21.67
846.6
21.64
Note:
1. The default test configuration is to measure SAR with an established radio link between the EUT and a
communication test set using a 12.2 kbps RMC (reference measurement Channel) Configured in Test Loop
Model 1.
2. KDB 941225 D01-Body SAR is not required for HSDPA/HSUPA/HSPA+ when the maximum average
output of each RF channel is less than ¼ dB higher than measured 12.2kbps RMC or the maximum
SAR for 12.2kbps RMC is < 75% of SAR limit.
SAR Evaluation Report
37 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
LTE Band 7:
Test
Test
Bandwidth
Modulation
QPSK
5M
16-QAM
QPSK
10M
16-QAM
QPSK
15M
16-QAM
SAR Evaluation Report
Resource
Block &
RB offset
1#0
1#12
1#24
12#0
12#6
12#11
25#0
1#0
1#12
1#24
12#0
12#6
12#11
25#0
1#0
1#24
1#49
25#0
25#12
25#24
50#0
1#0
1#24
1#49
25#0
25#12
25#24
50#0
1#0
1#37
1#74
36#0
36#17
36#35
75#0
1#0
1#37
1#74
36#0
36#17
36#35
75#0
Target
MPR
Meas
MPR
Low
Middle
High
Channel
Channel
Channel
(dBm)
22.11
21.66
21.94
21.39
21.29
20.86
21.52
21.12
21.44
21.5
21.66
21.88
21.37
21.56
21.31
21.43
21.95
20.93
21.47
21.43
20.67
21.07
22.2
21.59
21.73
22.17
21.23
21.62
21.38
21.45
21.26
20.97
21.48
21.24
21.08
21.2
21.73
21.97
21.12
22.08
22.04
21.61
(dBm)
21.75
21.32
21.4
21.62
21.37
21.4
21.14
21.8
21.52
20.95
21.76
21.28
21.47
21.5
21.8
21.69
21.86
21.29
21
20.87
20.69
21.53
21.37
21.6
21.44
21.89
21.49
21.73
21.11
21.59
21.85
21.82
21.54
21.4
21.21
21.13
21.41
21.57
21.42
21.17
22.15
22.02
(dBm)
21.54
21.62
21.64
21.89
20.95
21.21
21.45
21.76
21.14
21.22
21.32
21.07
21.91
21.8
21.01
21.02
21.13
21.25
21.61
20.77
21.1
21.55
21.99
22.21
21.92
21.62
21.59
22.29
21.74
21.61
21.13
21.36
21.58
21.34
20.91
21.67
21.74
21.12
21.43
21.87
21.31
21.36
38 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Test
Test
Bandwidth
Modulation
QPSK
20M
16-QAM
SAR Evaluation Report
Resource
Block &
RB offset
1#0
1#49
1#99
50#0
50#24
50#49
100#0
1#0
1#49
1#99
50#0
50#24
50#49
100#0
Report No.: RSZ180529003-20A
Target
MPR
Meas
MPR
Low
Middle
High
Channel
Channel
Channel
(dBm)
22.15
21.82
21.81
21.65
21.17
21.41
20.95
21
20.61
20.84
20.89
20.59
21.1
20.34
(dBm)
22.03
21.8
21.57
21.35
21.91
21.19
20.72
21.67
20.37
20.99
21
20.93
21.18
20.54
(dBm)
22.1
21.62
21.53
21.5
20.98
20.95
20.88
20.81
21.04
21.37
21.28
20.66
20.97
20.92
39 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
LTE Band 41:
Test
Test
Bandwidth
Modulation
QPSK
5M
16-QAM
QPSK
10M
16-QAM
QPSK
15M
16-QAM
SAR Evaluation Report
Resource
Block &
RB offset
1#0
1#12
1#24
12#0
12#6
12#11
25#0
1#0
1#12
1#24
12#0
12#6
12#11
25#0
1#0
1#24
1#49
25#0
25#12
25#24
50#0
1#0
1#24
1#49
25#0
25#12
25#24
50#0
1#0
1#37
1#74
36#0
36#17
36#35
75#0
1#0
1#37
1#74
36#0
36#17
36#35
75#0
Target
MPR
Meas
MPR
Low
Middle
High
Channel
Channel
Channel
(dBm)
21.78
21.36
21.53
21.63
21.45
21.36
21.15
21.87
21.65
21.08
21.84
21.32
21.52
21.46
21.29
21.49
21.39
21.07
21.47
21.54
20.8
21.19
21.27
21.66
21.73
22.17
21.38
21.74
21.34
21.58
21.29
21.04
21.5
21.23
21.15
21.34
21.74
21.96
21.26
21.33
21.99
21.64
(dBm)
21.4
21.57
21.79
21.53
21.45
21.12
21.45
21.72
21.66
21.4
21.41
21.54
21.44
21.21
21.41
21.42
21.29
21.3
21.29
21.08
20.61
21.57
21.57
21.53
21.66
21.53
21.53
21.35
21.47
21.42
21.51
21.47
21.32
21.17
21.19
21.2
21.62
21.79
21.68
21.81
21.88
21.83
(dBm)
21.43
21.51
21.63
21.45
21.38
21.33
21.41
21.51
21.54
21.47
21.46
21.35
21.63
21.41
21.5
21.55
21.3
21.25
21.27
21.27
21.15
21.42
21.62
21.89
21.67
21.6
21.56
21.87
21.5
21.26
21.41
21.43
21.51
21.6
21.3
21.31
21.61
21.62
21.55
21.5
21.63
21.52
40 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Test
Test
Bandwidth
Modulation
QPSK
20M
16-QAM
Note:
Resource
Block &
RB offset
1#0
1#49
1#99
50#0
50#24
50#49
100#0
1#0
1#49
1#99
50#0
50#24
50#49
100#0
Report No.: RSZ180529003-20A
Target
MPR
Meas
MPR
Low
Middle
High
Channel
Channel
Channel
(dBm)
21.93
21.61
20.96
21.68
21.27
21.55
20.93
21.08
20.59
20.81
20.99
20.61
21.11
20.34
(dBm)
21.96
21.97
21.27
21.09
21.75
21.17
20.98
21.36
20.96
21.13
21.08
20.69
20.99
20.99
(dBm)
21.89
21.54
21.18
21.23
21.34
21.48
21.17
20.99
20.82
20.91
21.13
20.98
20.82
20.82
1. SAR for LTE band exposure configurations is measured according to the procedures of KDB 941225 D05
SAR for LTE Devices v02.
2. The CMW500 Wideband Radio Communication tester is used for LTE output power measurements and
SAR testing. Closed loop power control is used to keep the radio transmitters the max output power during
the test.
3. KDB941225D05v02- SAR for higher order modulation is required only when the highest maximum output
power for the configuration in the higher order modulation is > ½ dB higher than the same configuration in
QPSK or when the reported SAR for the QPSK configuration is > 1.45 W/kg
SAR Evaluation Report
41 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
WLAN:
Mode
802.11b
802.11g
802.11n HT20
802.11n HT40
Channel
frequency (MHz)
2412
2442
2462
2412
2442
2462
2412
2442
2462
2422
2442
2452
Data Rate
1Mbps
6Mbps
MCS0
MCS0
RF Output
Power(dBm)
8.53
8.83
8.67
8.08
8.21
8.97
8.24
8.08
8.77
8.06
8.16
8.03
Bluetooth:
Mode
BDR(GFSK)
EDR(π/4-DQPSK)
EDR(8-DPSK)
Bluetooth LE
Channel frequency
(MHz)
2402
2431
2441
2480
2402
2441
2448
2480
2402
2441
2445
2480
2402
2440
2480
RF Output Power
(dBm)
5.17
6.69
5.45
1.41
4.41
4.68
6.24
1.50
4.65
4.99
6.62
1.78
-2.28
-1.25
-5.52
Note: For BDR/EDR,the highest output channel did not located in Low, Middle or High channel, another
more channel that has the highest output channel (2431/2445/2448 MHz) was selected to test.
SAR Evaluation Report
42 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
RG910 Test Results:
GSM:
Band
Frequency
RF Output Power
(MHz)
(dBm)
128
824.2
33.28
190
836.6
33.13
251
848.8
33.11
512
1850.2
28.26
661
1880
28.39
810
1909.8
28.36
Channel No.
GSM 850
PCS 1900
GPRS:
Band
GSM 850
PCS 1900
RF Output Power (dBm)
Channel
No.
Frequency
(MHz)
1 slot
2 slots
3 slots
4 slots
128
824.2
33.31
33.12
30.74
27.88
190
836.6
33.20
33.11
30.24
27.68
251
848.8
33.10
33.03
30.18
27.45
512
1850.2
28.35
26.63
26.12
22.61
661
1880
28.41
27.39
26.15
23.75
810
1909.8
28.38
27.48
26.14
24.04
Channel
No.
Frequency
(MHz)
1 slot
2 slots
3 slots
4 slots
128
824.2
27.43
25.82
24.55
23.32
190
836.6
27.07
25.27
24.07
22.97
251
848.8
26.95
25.10
23.96
22.70
512
1850.2
24.42
23.32
23.27
21.15
661
1880
25.26
24.30
23.43
22.21
810
1909.8
25.42
24.52
23.65
22.65
EDGE:
Band
GSM 850
PCS 1900
RF Output Power (dBm)
For SAR, the time based average power is relevant, the difference in between depends on the duty cycle of
the TDMA signal.
Number of Time slot
Duty Cycle
Time based Ave. power compared to
slotted Ave. power
Crest Factor
1:8
1:4
1:2.66
1:2
-9 dB
-6 dB
-4.25 dB
-3 dB
2.66
SAR Evaluation Report
43 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
The time based average power for GPRS
Band
Time based average Power (dBm)
Channel
No.
Frequency
(MHz)
1 slot
2 slot
3 slots
4 slots
128
824.2
24.31
27.12
26.49
24.88
190
836.6
24.2
27.11
25.99
24.68
251
848.8
24.1
27.03
25.93
24.45
512
1850.2
19.35
20.63
21.87
19.61
661
1880
19.41
21.39
21.9
20.75
810
1909.8
19.38
21.48
21.89
21.04
GSM 850
PCS 1900
The time based average power for EDGE
Band
Frequency
(MHz)
1 slot
2 slot
3 slots
4 slots
128
824.2
18.43
19.82
20.3
20.32
190
836.6
18.07
19.27
19.82
19.97
251
848.8
17.95
19.1
19.71
19.70
512
1850.2
15.42
17.32
19.02
18.15
661
1880
16.26
18.3
19.18
19.21
810
1909.8
16.42
18.52
19.4
19.65
GSM 850
PCS 1900
Note:
Time based average Power (dBm)
Channel
No.
1. Rohde & Schwarz Radio Communication Tester (CMU200) was used for the measurement of GSM peak
and average output power for active timeslots.
2 .For GPRS, 1, 2, 3 and 4 timeslots has been activated separately with power level 3(850 MHz band) and
3(1900 MHz band).
3. According to KDB941225D01-SAR for EGPRS mode are not required when the source-based
time-averaged output power for data mode is lower than that in the normal GPRS mode.
CDMA 1x RTT
Band
BC0
BC1
RF Output Power
(dBm)
RC3+SO32
RC3+SO55
(FCH)
21.54
21.23
Channel
Frequency
No.
(MHz)
1013
824.70
21.22
384
836.52
21.65
21.83
21.57
21.35
777
848.31
21.59
21.61
21.43
21.47
25
1851.25
21.22
21.42
21.22
21.52
600
1880
21.38
21.61
21.45
21.58
1175
1908.75
21.59
21.39
21.56
21.59
SAR Evaluation Report
RC1+SO55
RC3+SO32
(SCH)
21.26
44 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
EVDO
Band
Channel No.
BC0
BC1
Frequency
(MHz)
RF Output Power
(dBm)
RTAP 153.6kbps
RETAP 4096pbs
Subtype 0
Subtype 2
21.68
21.24
1013
824.7
384
836.52
21.33
21.28
777
848.31
21.42
21.67
25
1851.25
21.75
21.64
600
1880
21.62
21.45
1175
1908.75
21.51
21.49
WCDMA:
Results (12.2kbps RMC)
Frequency
Band
WCDMA Band 2
WCDMA Band 5
(MHz)
RF Output Power
(dBm)
1852.4
22.54
1880
22.64
1907.6
22.88
826.4
22.43
836.6
22.46
846.6
22.40
Results (HSDPA)
Band
WCDMA Band 2
WCDMA Band 5
SAR Evaluation Report
RF Output Power (dBm)
Frequency
(MHz)
Subset 1
Subset 2
Subset 3
Subset 4
1852.4
20.98
20.95
20.84
21.03
1880
21.19
21.31
21.12
21.15
1907.6
21.79
21.79
21.76
21.90
826.4
22.45
22.19
22.33
22.18
836.6
22.44
22.36
22.41
22.19
846.6
22.24
22.17
22.32
22.15
45 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
Results (HSUPA)
Band
WCDMA Band 2
WCDMA Band 5
RF Output Power (dBm)
Frequency
(MHz)
Subset 1
Subset 2
Subset 3
Subset 4
Subset 5
1852.4
20.60
20.43
20.65
20.52
20.66
1880
20.56
20.62
20.78
20.46
20.61
1907.6
21.17
21.18
21.32
21.22
21.17
826.4
21.79
21.79
21.96
21.68
21.87
836.6
21.88
21.79
21.86
21.83
21.94
846.6
21.85
21.74
21.83
21.70
21.77
Results (HSPA+)
Band
WCDMA Band 2
WCDMA Band 5
Frequency
(MHz)
RF Output Power
(dBm)
1852.4
20.40
1880
20.42
1907.6
20.98
826.4
21.63
836.6
21.65
846.6
21.61
Note:
1. The default test configuration is to measure SAR with an established radio link between the EUT and a
communication test set using a 12.2 kbps RMC (reference measurement Channel) Configured in Test Loop
Model 1.
2. KDB 941225 D01-Body SAR is not required for HSDPA/HSUPA/HSPA+ when the maximum average
output of each RF channel is less than ¼ dB higher than measured 12.2kbps RMC or the maximum
SAR for 12.2kbps RMC is < 75% of SAR limit.
SAR Evaluation Report
46 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
LTE Band 7:
Test
Test
Bandwidth
Modulation
QPSK
5M
16-QAM
QPSK
10M
16-QAM
QPSK
15M
16-QAM
SAR Evaluation Report
Resource
Block &
RB offset
1#0
1#12
1#24
12#0
12#6
12#11
25#0
1#0
1#12
1#24
12#0
12#6
12#11
25#0
1#0
1#24
1#49
25#0
25#12
25#24
50#0
1#0
1#24
1#49
25#0
25#12
25#24
50#0
1#0
1#37
1#74
36#0
36#17
36#35
75#0
1#0
1#37
1#74
36#0
36#17
36#35
75#0
Target
MPR
Meas
MPR
Low
Middle
High
Channel
Channel
Channel
(dBm)
22.06
21.55
22.06
21.45
21.3
20.88
21.35
21.14
21.47
21.54
21.84
21.79
21.47
21.58
21.16
21.5
21.96
20.89
21.49
21.55
20.74
21.06
22.06
21.63
21.71
22.11
21.19
21.71
21.34
21.58
21.12
21
21.49
21.19
20.98
21.27
21.74
21.82
21.12
22.1
22.08
21.62
(dBm)
21.65
21.28
21.34
21.53
21.5
21.39
21.18
21.73
21.56
21.06
21.62
21.33
21.38
21.46
21.69
21.69
21.77
21.34
20.93
20.96
20.57
21.48
21.28
21.7
21.57
21.73
21.49
21.79
21.1
21.63
21.84
21.93
21.49
21.41
21.23
21.08
21.38
21.64
21.32
21.23
22.11
22.1
(dBm)
21.46
21.57
21.63
21.95
21.11
21.23
21.4
21.76
21.13
21.28
21.47
21.02
21.86
21.79
21.13
21.01
21.25
21.2
21.51
20.76
21
21.64
21.98
22.08
21.91
21.64
21.6
22.12
21.86
21.59
21.05
21.38
21.57
21.33
20.94
21.76
21.79
21.04
21.42
21.95
21.29
21.39
47 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Test
Test
Bandwidth
Modulation
QPSK
20M
16-QAM
SAR Evaluation Report
Resource
Block &
RB offset
1#0
1#49
1#99
50#0
50#24
50#49
100#0
1#0
1#49
1#99
50#0
50#24
50#49
100#0
Report No.: RSZ180529003-20A
Target
MPR
Meas
MPR
Low
Middle
High
Channel
Channel
Channel
(dBm)
22.08
21.72
21.87
21.55
21.19
21.45
20.95
20.91
20.6
20.98
20.9
20.68
21.14
20.33
(dBm)
21.94
21.81
21.62
21.37
21.86
21.35
20.68
21.71
20.49
21.08
20.82
20.97
21.18
20.51
(dBm)
21.87
21.45
21.46
21.36
20.86
21.08
20.89
20.91
21.07
21.34
21.33
20.77
20.97
20.78
48 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
LTE Band 41:
Test
Test
Bandwidth
Modulation
QPSK
5M
16-QAM
QPSK
10M
16-QAM
QPSK
15M
16-QAM
SAR Evaluation Report
Resource
Block &
RB offset
1#0
1#12
1#24
12#0
12#6
12#11
25#0
1#0
1#12
1#24
12#0
12#6
12#11
25#0
1#0
1#24
1#49
25#0
25#12
25#24
50#0
1#0
1#24
1#49
25#0
25#12
25#24
50#0
1#0
1#37
1#74
36#0
36#17
36#35
75#0
1#0
1#37
1#74
36#0
36#17
36#35
75#0
Target
MPR
Meas
MPR
Low
Middle
High
Channel
Channel
Channel
(dBm)
21.53
21.66
21.51
21.52
21.37
21.49
21.22
21.51
21.49
21.55
21.48
21.54
21.48
21.31
21.44
21.38
21.33
21.4
21.28
21.32
21.16
21.6
21.64
21.72
21.6
21.59
21.67
21.67
21.33
21.24
21.5
21.57
21.47
21.33
21.48
21.32
21.53
21.68
21.47
21.66
21.55
21.55
(dBm)
21.42
21.66
21.74
21.56
21.35
21.16
21.37
21.7
21.7
21.53
21.41
21.61
21.49
21.04
21.4
21.49
21.25
21.28
21.18
20.98
20.65
21.44
21.6
21.55
21.63
21.63
21.51
21.53
21.59
21.3
21.6
21.63
21.42
21.09
21.18
21.18
21.7
21.75
21.66
21.65
22.15
21.83
(dBm)
21.49
21.46
21.63
21.5
21.4
21.47
21.39
21.52
21.51
21.53
21.47
21.36
21.6
21.33
21.43
21.42
21.36
21.22
21.32
21.27
21.16
21.45
21.54
21.79
21.65
21.64
21.61
21.81
21.47
21.31
21.37
21.37
21.67
21.55
21.23
21.35
21.47
21.51
21.66
21.59
21.73
21.54
49 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Test
Test
Bandwidth
Modulation
QPSK
20M
16-QAM
Note:
Resource
Block &
RB offset
1#0
1#49
1#99
50#0
50#24
50#49
100#0
1#0
1#49
1#99
50#0
50#24
50#49
100#0
Report No.: RSZ180529003-20A
Target
MPR
Meas
MPR
Low
Middle
High
Channel
Channel
Channel
(dBm)
21.82
21.65
21.28
21.33
21.45
21.2
21.29
21.03
20.92
21.09
20.9
20.77
20.9
20.91
(dBm)
21.89
21.74
21.58
21.03
21.67
21.19
21.01
21.2
20.9
21.15
21
20.85
21.07
21.04
(dBm)
21.81
21.61
21.65
21.26
21.33
21.43
21.21
20.96
20.92
20.95
21.18
20.87
20.81
20.9
1. SAR for LTE band exposure configurations is measured according to the procedures of KDB 941225 D05
SAR for LTE Devices v02.
2. The CMW500 Wideband Radio Communication tester is used for LTE output power measurements and
SAR testing. Closed loop power control is used to keep the radio transmitters the max output power during
the test.
3. KDB941225D05v02- SAR for higher order modulation is required only when the highest maximum output
power for the configuration in the higher order modulation is > ½ dB higher than the same configuration in
QPSK or when the reported SAR for the QPSK configuration is > 1.45 W/kg
SAR Evaluation Report
50 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
WLAN:
Mode
802.11b
802.11g
802.11n HT20
802.11n HT40
Channel
frequency (MHz)
2412
2442
2462
2412
2442
2462
2412
2442
2462
2422
2442
2452
Data Rate
1Mbps
6Mbps
MCS0
MCS0
RF Output
Power(dBm)
8.67
8.81
8.60
8.17
8.10
8.94
8.07
8.09
8.74
7.93
8.14
8.10
Bluetooth:
Mode
BDR(GFSK)
EDR(π/4-DQPSK)
EDR(8-DPSK)
Bluetooth LE
Channel frequency
(MHz)
2402
2431
2441
2480
2402
2441
2448
2480
2402
2441
2445
2480
2402
2440
2480
RF Output Power
(dBm)
5.13
6.62
5.45
1.53
4.50
4.55
6.33
1.33
4.84
4.90
6.58
1.69
-2.26
-1.38
-5.49
Note: For BDR/EDR,the highest output channel did not located in Low, Middle or High channel, another
more channel that has the highest output channel (2431/2445/2448 MHz) was selected to test.
SAR Evaluation Report
51 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
Standalone SAR test exclusion considerations
Antennas Location:
Top
135mm
193mm
GSM&CDMA&WCD
MA<E AUX
Front
Back(Reverse)
Left
11m
134mm
BT&WLAN
Antenna
90mm
123m
Right
9mm
GSM&CDMA&
WCDMA<E TX
Antenna
10mm
Bottom
Antenna Distance To Edge
Antenna Distance To Edge(mm)
Antenna
Back
Left
Right
Top
Bottom
WWAN(GSM/CDMA/WCDMA/LTE)
WLAN/BT Antenna
<5
<5
123
134
11
193
135
10
90
Standalone SAR test exclusion considerations
Frequency
(MHz)
Pavg
(dBm)
Pavg
(mW)
Distance
(mm)
Calculated
value
Threshold
(1-g)
SAR Test
Exclusion
WLAN
2462
7.94
2.5
YES
Bluetooth
2480
5.01
1.6
YES
Mode
NOTE:
The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are
determined by:
[( max. power of channel, including tune-up tolerance, mW )/( min. test separation distance, mm)] ·
[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤7.5 for 10-g extremity SAR, where
1. f(GHz) is the RF channel transmit frequency in GHz.
2. Power and distance are rounded to the nearest mW and mm before calculation.
3. The result is rounded to one decimal place for comparison.
4. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test
Exclusion.
SAR Evaluation Report
52 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
Standalone SAR test exclusion considerations detail:
Mode
Frequency
(MHz)
Pavg
(dBm)
Pavg
(mW)
Test Exclusion
Distance (mm)
GSM 850
848.8
27.2
524.8
114
PCS 1900
1909.8
22.1
162.2
55
CDMA 850
848.31
22
158.5
49
CDMA 1900
1908.75
21.8
151.4
54
WCDMA Band 2
1907.6
22.96
197.7
59
WCDMA Band 5
846.6
22.52
178.6
53
LTE Band 7
2560
22.3
169.8
58
LTE Band 41
2605
22.2
166
58
SAR test exclusion for the EUT edge considerations Result
Mode
Back
Left
Right
Top
Bottom
GSM 850
PCS 1900
CDMA 850
CDMA 1900
WCDMA Band 2
WCDMA Band 5
LTE Band 7
LTE Band 41
WLAN
BT
Required
Required
Required
Required
Required
Required
Required
Required
Selected
Selected
Exclusion
Exclusion
Exclusion
Exclusion
Exclusion
Exclusion
Exclusion
Exclusion
Exclusion
Exclusion
Required
Required
Required
Required
Required
Required
Required
Required
Selected
Selected
Exclusion
Exclusion
Exclusion
Exclusion
Exclusion
Exclusion
Exclusion
Exclusion
Exclusion
Exclusion
Required
Required
Required
Required
Required
Required
Required
Required
Exclusion
Exclusion
Note:
Required:The distance is less than Test Exclusion Distance, the SAR test is required.
Exclusion: The distance is large than Test Exclusion Distance, SAR test is not required.
Selected: Though SAR scan can be exclusived, measurement for this edge was selected to be performed for
conservative consideration.
SAR test exclusion for the EUT edge considerations detail:
Distance< 50mm(To Edges)
The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are
determined by:
[( max. power of channel, including tune-up tolerance, mW )/( min. test separation distance, mm)] ·
[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤7.5 for 10-g extremity SAR, where
1. f(GHz) is the RF channel transmit frequency in GHz.
2. Power and distance are rounded to the nearest mW and mm before calculation.
3. The result is rounded to one decimal place for comparison.
4. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test
Exclusion.
5. The Time based average Power is used for calculation
SAR Evaluation Report
53 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
Distance> 50mm(To Edges)
At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined
according to the following:
a) [Power allowed at numeric threshold for 50 mm in step 1) + (test separation distance - 50 mm)·( f(MHz)/150)]
mW, at 100 MHz to 1500 MHz
b) [Power allowed at numeric threshold for 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at >
1500 MHz and ≤ 6 GHz
SAR Evaluation Report
54 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
SAR MEASUREMENT RESULTS
This page summarizes the results of the performed dosimetric evaluation.
SAR Test Data
Environmental Conditions
Temperature:
21.5-22.1 ℃
21.7-22.5 ℃
20.6-21.8 ℃
20.3-21.0 ℃
50 %
49 %
42 %
50 %
ATM Pressure:
101.6 kPa
101.3 kPa
101.3 kPa
101.3 kPa
Test Date:
2018/06/09
2018/06/10
2018/06/12
2018/06/13
Relative Humidity:
Testing was performed by Gaochao Gong, Sam Liang, William Ye.
SAR Evaluation Report
55 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
GSM 850:
EUT
Position
Tested
Model
Body Worn Back
IS910.1
(0mm)
Body Back
(0mm)
IS910.1
RG910
Body Right
(0mm)
Body Bottom
(0mm)
Note:
IS910.1
IS910.1
Scaled
Factor
Meas.
SAR
GSM
Max.
Max.
Meas. Rated
Power Power
(dBm) (dBm)
836.6
GSM
33.19
33.5
1.074
0.128
0.137
0.14
1#
848.8
GSM
824.2
GPRS
33.13
33.2
1.016
0.198
0.201
0.20
2#
836.6
GPRS
33.02
33.2
1.042
0.192
0.200
0.20
3#
848.8
GPRS
32.97
33.2
1.054
0.174
0.183
0.18
4#
824.2
GPRS
33.12
33.2
1.019
0.180
0.183
0.18
5#
824.2
GPRS
836.6
GPRS
33.02
33.2
1.042
0.071
0.074
0.07
6#
848.8
GPRS
824.2
GPRS
836.6
GPRS
33.02
33.2
1.042
0.170
0.177
0.18
7#
848.8
GPRS
Frequency
(MHz)
Test
Mode
824.2
1g SAR (W/kg)
Scaled Corrected
Plot
SAR
SAR
1. When the 1-g SAR is ≤ 0.8W/kg, testing for other channels are optional.
2. The EUT transmit and receive through the same GSM antenna while testing SAR.
3. When SAR or MPE is not measured at the maximum power level allowed for production units, the results
must be scaled to the maximum tune-up tolerance limit according to the power applied to the individual
channels tested to determine compliance.
4. When the maximum output power variation across the required test channels is > ½ dB, instead of the
middle channel, the highest output power channel must be used.
5. The Multi-slot Classes of EUT is Class 12 which has maximum 4 Downlink slots and 4 Uplink slots, the
maximum active slots is 5, when perform the multiple slots scan, 3DL+2UL is the worst case.
6. According to IEC 62209-2:2010 ,If the correction ΔSAR has a positive sign, the measured SAR results shall
not be corrected.
SAR Evaluation Report
56 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
GSM 1900:
EUT
Position
Body Worn Back
(0mm)
Body Back
(0mm)
Tested
Model
IS910.1
IS910.1
RG910
Body Right
(0mm)
Body Bottom
(10mm)
Note:
IS910.1
IS910.1
Scaled
Factor
Meas.
SAR
Scaled Corrected
Plot
SAR
SAR
GSM
Max.
Max.
Meas. Rated
Power Power
(dBm) (dBm)
28.29
28.5
1.050
0.875
0.919
0.95
8#
1880
GSM
28.42
28.5
1.019
0.835
0.851
0.87
9#
1909.8
GSM
28.4
28.5
1.023
0.750
0.767
0.77
10#
1850.2
GPRS
26.29
26.4
1.026
0.931
0.95
0.98
11#
1880
GPRS
26.28
26.4
1.028
1.07
1.100
1.12
12#
1909.8
GPRS
26.24
26.4
1.038
0.931
0.966
1.00
13#
1880
GPRS
26.15
26.4
1.059
0.765
0.810
0.82
14#
1850.2
GPRS
26.29
26.4
1.026
0.630
0.646
0.67
15#
1880
GPRS
26.28
26.4
1.028
0.864
0.888
0.90
16#
1909.8
GPRS
26.24
26.4
1.038
0.795
0.825
0.85
17#
1850.2
GPRS
1880
GPRS
26.28
26.4
1.028
0.449
0.462
0.47
18#
1909.8
GPRS
Frequency
(MHz)
Test
Mode
1850.2
1g SAR (W/kg)
1. When the 1-g SAR is ≤ 0.8W/kg, testing for other channels are optional.
2. The EUT transmit and receive through the same GSM antenna while testing SAR.
3. When SAR or MPE is not measured at the maximum power level allowed for production units, the results
must be scaled to the maximum tune-up tolerance limit according to the power applied to the individual
channels tested to determine compliance.
4. When the maximum output power variation across the required test channels is > ½ dB, instead of the
middle channel, the highest output power channel must be used.
5. The Multi-slot Classes of EUT is Class 12 which has maximum 4 Downlink slots and 4 Uplink slots, the
maximum active slots is 5, when perform the multiple slots scan, 2DL+3UL is the worst case.
6. According to IEC 62209-2:2010 ,If the correction ΔSAR has a positive sign, the measured SAR results shall
not be corrected.
SAR Evaluation Report
57 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
CDMA 850(BC0):
EUT
Position
Body Worn Back
(0mm)
Body Back
(0mm)
Tested
Model
IS910.1
IS910.1
RG910
Body Right
(0mm)
Body Bottom
(0mm)
IS910.1
IS910.1
Max.
Frequency
Meas.
Test Mode
(MHz)
Power
(dBm)
RC3+SO55
824.70
Max.
Rated
Power
(dBm)
Scaled
Factor
Meas.
SAR
1g SAR (W/kg)
Scaled Corrected
Plot
SAR
SAR
836.52
RC3+SO55
21.86
22
1.033
0.340
0.351
0.36
19#
848.31
RC3+SO55
824.70
RTAP 153.6 21.71
21.8
1.021
0.415
0.424
0.44
20#
836.52
RTAP 153.6 21.42
21.8
1.091
0.353
0.385
0.39
21#
848.31
RTAP 153.6 21.52
21.8
1.067
0.388
0.414
0.42
22#
824.70
RTAP 153.6 21.68
21.8
1.028
0.402
0.413
0.42
23#
824.70
RTAP 153.6
836.52
RTAP 153.6 21.42
21.8
1.091
0.169
0.184
0.19
24#
848.31
RTAP 153.6
824.70
RTAP 153.6
836.52
RTAP 153.6 21.42
21.8
1.091
0.307
0.335
0.34
25#
848.31
RTAP 153.6
CDMA 1900(BC1):
EUT
Position
Body Worn Back
(0mm)
Body Back
(0mm)
Tested
Model
IS910.1
IS910.1
RG910
Body Right
(0mm)
Body Bottom
(0mm)
IS910.1
IS910.1
SAR Evaluation Report
Scaled
Factor
Meas.
SAR
Scaled Corrected
Plot
SAR
SAR
RC3+SO55
Max.
Max.
Meas. Rated
Power Power
(dBm) (dBm)
21.34
21.8
1.112
0.767
0.853
0.88
26#
1880
RC3+SO55
21.65
21.8
1.035
0.815
0.844
0.86
27#
1908.75
RC3+SO55
21.37
21.8
1.104
0.813
0.898
0.90
28#
1851.25
RTAP 153.6
21.79
21.9
1.026
0.861
0.883
0.91
29#
1880
RTAP 153.6
21.64
21.9
1.062
0.895
0.950
0.97
30#
1908.75
RTAP 153.6
21.56
21.9
1.081
0.797
0.862
0.86
31#
1880
RTAP 153.6
21.62
21.9
1.067
0.782
0.834
0.85
32#
1851.25
RTAP 153.6
1880
RTAP 153.6
21.64
21.9
1.062
0.591
0.628
0.64
33#
1908.75
RTAP 153.6
1851.25
RTAP 153.6
1880
RTAP 153.6
21.64
21.9
1.062
0.322
0.342
0.35
34#
1908.75
RTAP 153.6
Frequency
(MHz)
Test Mode
1851.25
1g SAR (W/kg)
58 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Note:
Report No.: RSZ180529003-20A
1. When the 1-g SAR is≤ 0.8W/kg, testing for other channels are optional.
2. The EUT transmit and receive through the same antenna while testing SAR.
3. When SAR or MPE is not measured at the maximum power level allowed for production units, the results
must be scaled to the maximum tune-up tolerance limit according to the power applied to the individual
channels tested to determine compliance.
4. According to IEC 62209-2:2010 ,If the correction ΔSAR has a positive sign, the measured SAR results shall
not be corrected.
WCDMA Band 2:
EUT
Position
Body Back
(0mm)
Tested
Model
IS910.1
RG910
Body Right
(0mm)
Body Bottom
(0mm)
IS910.1
IS910.1
Scaled
Factor
Meas.
SAR
Scaled Corrected
Plot
SAR
SAR
RMC
Max.
Max.
Meas. Rated
Power Power
(dBm) (dBm)
22.59
23.1
1.125
0.850
0.956
0.98
35#
1880
RMC
22.64
23.1
1.112
0.929
1.033
1.05
36#
1907.6
RMC
22.96
23.1
1.033
1.01
1.043
1.05
37#
1907.6
RMC
22.88
23.1
1.052
0.825
0.868
0.87
38#
1852.4
RMC
22.59
23.1
1.125
0.661
0.744
0.76
39#
1880
RMC
22.64
23.1
1.112
0.847
0.942
0.96
40#
1907.6
RMC
22.96
23.1
1.033
0.896
0.926
0.93
41#
1852.4
RMC
1880
RMC
22.64
23.1
1.112
0.481
0.535
0.54
42#
1907.6
RMC
Frequency
(MHz)
Test
Mode
826.4
Frequency
(MHz)
Test
Mode
1852.4
1g SAR (W/kg)
WCDMA Band 5:
EUT
Position
Body Back
(0mm)
Body Right
(0mm)
Body Bottom
(0mm)
Tested
Model
IS910.1
IS910.1
IS910.1
RG910
SAR Evaluation Report
Scaled
Factor
Meas.
SAR
RMC
Max.
Max.
Meas. Rated
Power Power
(dBm) (dBm)
836.6
RMC
22.52
22.6
1.019
0.181
0.184
0.18
43#
846.6
RMC
826.4
RMC
836.6
RMC
22.52
22.6
1.019
0.105
0.107
0.11
44#
846.6
RMC
826.4
RMC
22.49
22.6
1.026
0.231
0.237
0.24
45#
836.6
RMC
22.52
22.6
1.019
0.195
0.199
0.20
46#
846.6
RMC
22.45
22.6
1.035
0.162
0.168
0.17
47#
826.4
RMC
22.43
22.6
1.04
0.217
0.226
0.23
48#
1g SAR (W/kg)
Scaled Corrected
Plot
SAR
SAR
59 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Note:
Report No.: RSZ180529003-20A
1. When the 1-g SAR is≤ 0.8W/kg, testing for other channels are optional.
2. The EUT transmit and receive through the same antenna while testing SAR.
3. The default test configuration is to measure SAR with an established radio link between the EUT and a
communication test set using a 12.2 kbps RMC (reference measurement Channel) Configured in Test Loop
Model.
4. KDB 941225 D01-Body SAR is not required for HSDPA/HSUPA/HSPA+ when the maximum average
output of each RF channel is less than ¼ dB higher than measured 12.2kbps RMC or the maximum SAR for
12.2kbps RMC is < 75% of SAR limit.
5. When SAR or MPE is not measured at the maximum power level allowed for production units, the results
must be scaled to the maximum tune-up tolerance limit according to the power applied to the individual
channels tested to determine compliance.
6. According to IEC 62209-2:2010 ,If the correction ΔSAR has a positive sign, the measured SAR results shall
not be corrected.
LTE Band 7:
EUT
Position
Body Back
(0mm)
IS910.1
RG910
Body Right
(0mm)
Body Bottom
(0mm)
2510
20
1RB
Max.
Meas.
Power
(dBm)
22.15
2535
20
1RB
22.03
22.3
1.064
0.307
0.327
0.33
50#
2560
20
1RB
22.1
22.3
1.047
0.304
0.318
0.32
51#
2535
20
50%RB
21.91
22.3
1.094
0.254
0.278
0.28
52#
2510
20
1RB
22.08
22.3
1.052
0.268
0.282
0.28
53#
2510
20
1RB
2535
20
1RB
22.03
22.3
1.064
0.301
0.320
0.32
54#
2560
20
1RB
2535
20
50%RB
21.91
22.3
1.094
0.233
0.255
0.26
55#
2510
20
1RB
2535
20
1RB
22.03
22.3
1.064
0.200
0.213
0.21
56#
2560
20
1RB
2535
20
50%RB
21.91
22.3
1.094
0.162
0.177
0.18
57#
Tested Frequency Bandwidth
Model
(MHz)
(MHz)
IS910.1
IS910.1
SAR Evaluation Report
Test
Mode
Max.
1g SAR (W/kg)
Rated
Power Scaled Meas. Scaled Corrected Plot
SAR
SAR
(dBm) Factor SAR
22.3 1.035 0.358 0.371
0.37
49#
60 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
LTE Band 41:
EUT
Position
Body Back
(0mm)
Tested
Model
IS910.1
RG910
Body Right
(0mm)
Body Bottom
(0mm)
Note:
IS910.1
IS910.1
2565
20
1RB
Max.
Meas.
Power
(dBm)
21.93
2605
20
1RB
21.96
22.2
1.057
0.238
0.252
0.25
59#
2645
20
1RB
21.89
22.2
1.074
0.152
0.163
0.16
60#
2605
20
50%RB
21.75
22.2
1.109
0.133
0.147
0.15
61#
2605
20
1RB
21.89
22.2
1.074
0.208
0.223
0.22
62#
2565
20
1RB
2605
20
1RB
21.96
22.2
1.057
0.085
0.090
0.09
63#
2645
20
1RB
2605
20
50%RB
21.75
22.2
1.109
0.074
0.082
0.08
64#
2565
20
1RB
2605
20
1RB
21.96
22.2
1.057
0.091
0.096
0.10
65#
2645
20
1RB
2605
20
50%RB
21.75
22.2
1.109
0.079
0.088
0.09
66#
Frequency Bandwidth Test
(MHz)
(MHz)
Mode
Max.
1g SAR (W/kg)
Rated
Power Scaled Meas. Scaled Corrected
SAR
SAR
(dBm) Factor SAR
22.2 1.064 0.156 0.166
0.17
Plot
58#
1. SAR for LTE band exposure configurations is measured according to the procedures of KDB 941225 D05
SAR for LTE Devices v02.
2. KDB941225D05- Start with the largest channel bandwidth and measure SAR for QPSK with 1 RB
allocation, using the RB offset and required test channel combination with the highest maximum output
power among RB offset the upper edge, middle and lower edge of each required test channel.
3. When the 1-g SAR is ≤ 0.8W/kg, testing for other channels are optional.
4. Worst case SAR for 50% RB allocation is selected to be tested.
5.KDB941225D05- For QPSK with 100% RB allocation, SAR is not required when the highest maximum
output power for 100 % RB allocation is less than the highest maximum output power in 50% and 1 RB
allocations and the highest reported SAR for 1 RB and 50% RB allocation are ≤ 0.8 W/kg.
6. KDB941225D05-For QPSK with 100% RB allocation, when the reported SAR measured for the Highest
output power channel is <1.45 W/kg, tests for the remaining required test channels are optional.
7. KDB941225D05- other channel bandwidths SAR test is required when the highest maximum output power
of a configuration requiring testing in the smaller channel bandwidth is > ½ dB higher than the equivalent
channel configurations in the largest channel bandwidth configuration or the reported SAR of a configuration
for the largest channel bandwidth is > 1.45 W/kg.
8. KDB941225D05-SAR for higher order modulation is required only when the highest maximum output
power for the configuration in the higher order modulation is > ½ dB higher than the same configuration in
QPSK or when the reported SAR for the QPSK configuration is > 1.45 W/kg
9. According to IEC 62209-2:2010 ,If the correction ΔSAR has a positive sign, the measured SAR results shall
not be corrected.
SAR Evaluation Report
61 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
WLAN 2.4G:
EUT
Position
Body Back
(0mm)
Tested
Model
IS910.1
RG910
Body Right
(0mm)
Note:
IS910.1
2412
Max.
Max.
Meas. Rated
Power Power
(dBm) (dBm)
802.11b 8.53
2442
802.11b
8.83
1.04
0.079
0.082
0.08
68#
2462
802.11b
8.67
1.079
0.045
0.049
0.05
69#
2442
802.11b
8.81
1.045
0.063
0.066
0.07
70#
2412
802.11b
2442
802.11b
8.83
1.04
0.056
0.058
0.06
71#
2462
802.11b
Frequency
(MHz)
Test
Mode
1g SAR (W/kg)
Scaled
Factor
Meas.
SAR
Scaled Corrected
Plot
SAR
SAR
1.114
0.044
0.049
0.05
67#
1.When the SAR value is less than half of the limit, testing for other channels are optional.
2.When SAR or MPE is not measured at the maximum power level allowed for production units, the results
must be scaled to the maximum tune-up tolerance limit according to the power applied to the individual
channels tested to determine compliance.
3.KDB 248227 D01-SAR measurement is not required for 2.4 GHz OFDM(801.11g/n20) when the highest
reported SAR for DSSS(802.11b) is ≤ 1.2 W/kg, and the output power for DSSS is not less than that for
OFDM.
4. According to IEC 62209-2:2010 ,If the correction ΔSAR has a positive sign, the measured SAR results shall
not be corrected.
Bluetooth:
EUT
Position
Body Back
(0mm)
Tested
Model
IS910.1
RG910
Body Right
(0mm)
IS910.1
Max. Max.
Meas. Rated
Power Power
(dBm) (dBm)
5.17
Frequency
(MHz)
Test
Mode
2402
GFSK
2431
GFSK
6.69
2441
GFSK
2480
1g SAR (W/kg)
Scaled
Factor
Meas.
SAR
Scaled Corrected
Plot
SAR
SAR
1.524
0.028
0.043
0.04
72#
1.074
0.037
0.04
0.04
73#
5.45
1.429
0.03
0.043
0.04
74#
GFSK
1.41
1.146
<0.01
0.01
0.01
2431
GFSK
6.62
1.091
0.024
0.026
0.03
75#
2402
GFSK
2431
GFSK
6.69
1.074
0.024
0.026
0.03
76#
2441
GFSK
2480
GFSK
Note:
1. When the 1-g SAR is≤ 0.8W/kg, testing for other channels are optional.
2. When SAR or MPE is not measured at the maximum power level allowed for production units, the results must
be scaled to the maximum tune-up tolerance limit according to the power applied to the individual channels
tested to determine compliance.
3. For modes that peak SAR is too low to evaluate, a SAR value 0.01W/kg is considered as their Scaled SAR.
4. According to IEC 62209-2:2010 ,If the correction ΔSAR has a positive sign, the measured SAR results shall not
be corrected.
SAR Evaluation Report
62 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
SAR Evaluation Report
Report No.: RSZ180529003-20A
63 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
Corrected SAR Evaluation Table
Frequency
(MHz)
Liquid
Type
Cε
△εr
Cδ
△δ
△SAR
(%)
750
824.2
824.7
826.4
836.52
836.6
846.6
848.31
848.8
1g Body
1g Body
1g Body
1g Body
1g Body
1g Body
1g Body
1g Body
1g Body
-0.218
-0.219
-0.219
-0.219
-0.219
-0.219
-0.220
-0.220
-0.220
2.87
3.7
3.94
3.89
3.57
3.25
3.11
3.06
3.04
0.761
0.754
0.754
0.754
0.753
0.753
0.752
0.752
0.752
-2.92
-2.68
-2.37
-1.75
-0.93
-0.93
-1.73
-2.32
-1.72
-2.85
-2.83
-2.65
-2.17
-1.48
-1.41
-1.98
-2.42
-1.96
Frequency
(MHz)
Liquid
Type
Cε
△εr
Cδ
△δ
△SAR
(%)
1850.2
1851.25
1852.4
1880
1900
1907.6
1908.75
1909.8
1g Body
1g Body
1g Body
1g Body
1g Body
1g Body
1g Body
1g Body
-0.226
-0.226
-0.226
-0.226
-0.226
-0.226
-0.226
-0.226
2.44
2.42
2.41
1.7
1.64
1.57
1.52
1.5
0.604
0.603
0.603
0.598
0.594
0.593
0.592
0.592
-4.34
-3.88
-3.42
-2.11
-0.33
-0.26
0.07
0.72
-3.17
-2.89
-2.61
-1.65
-0.57
-0.51
-0.30
0.09
Frequency
(MHz)
Liquid
Type
Cε
△εr
Cδ
△δ
△SAR
(%)
2402
2412
2431
2441
2442
2450
2462
2480
2510
2535
1g Body
1g Body
1g Body
1g Body
1g Body
1g Body
1g Body
1g Body
1g Body
1g Body
-0.225
-0.225
-0.225
-0.225
-0.225
-0.225
-0.225
-0.225
-0.225
-0.224
3.15
3.11
2.93
2.8
2.8
2.33
2.14
2.16
2.01
1.78
0.491
0.489
0.484
0.482
0.482
0.480
0.478
0.474
0.467
0.462
-1.79
-0.26
-0.62
-0.46
-0.36
0.1
0.05
-0.4
-2.21
-0.58
-1.59
-0.83
-0.96
-0.85
-0.80
-0.48
-0.46
-0.67
-1.48
-0.67
Frequency
(MHz)
Liquid
Type
Cε
△εr
Cδ
△δ
△SAR
(%)
2560
2565
2605
2600
2645
1g Body
1g Body
1g Body
1g Body
1g Body
-0.224
-0.224
-0.224
-0.224
-0.224
1.86
1.56
1.62
1.6
1.67
0.456
0.455
0.446
0.447
0.437
0.57
1.23
-1.15
-0.42
-2.91
-0.16
0.21
-0.88
-0.55
-1.65
SAR Evaluation Report
64 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
SAR Evaluation Report
Report No.: RSZ180529003-20A
65 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
SAR Measurement Variability
In accordance with published RF Exposure KDB procedure 865664 D01 SAR measurement 100 MHz to 6
GHz v01. These additional measurements are repeated after the completion of all measurements requiring
the same head or body tissue-equivalent medium in a frequency band. The test device should be returned
to ambient conditions (normal room temperature) with the battery fully charged before it is re-mounted on
the device holder for the repeated measurement(s) to minimize any unexpected variations in the repeated
results
1) Repeated measurement is not required when the original highest measured SAR is < 0.80 W/kg;
steps 2) through 4) do not apply.
2) When the original highest measured SAR is ≥ 0.80 W/kg, repeat that measurement once.
3) Perform a second repeated measurement only if the ratio of largest to smallest SAR for the
original and first repeated measurements is > 1.20 or when the original or repeated measurement
is ≥ 1.45 W/kg (~ 10% from the 1-g SAR limit).
4) Perform a third repeated measurement only if the original, first or second repeated measurement is
≥1.5 W/kg and the ratio of largest to smallest SAR for the original, first and second repeated
measurements is > 1.20.
Note: The same procedures should be adapted for measurements according to extremity and occupational
exposure limits by applying a factor of 2.5 for extremity exposure and a factor of 5 for occupational
exposure to the corresponding SAR thresholds.
The Highest Measured SAR Configuration in Each Frequency Band
Body
Tested
Model
SAR probe
calibration point
Frequency
Band
Freq.(MHz)
EUT
Position
IS910.1
1900MHz
(1850-2000 MHz)
GSM 1900
1880
Body Back
Meas. SAR (W/kg)
Original
Repeated
Largest to
Smallest
SAR Ratio
1.07
1.04
1.03
Note:
1. Second Repeated Measurement is not required since the ratio of the largest to smallest SAR for the original
and first repeated measurement is not > 1.20.
2. The measured SAR results do not have to be scaled to the maximum tune-up tolerance to determine if
repeated measurements are required.
3. SAR measurement variability must be assessed for each frequency band, which is determined by the SAR
probe calibration point and tissue-equivalent medium used for the device measurements..
SAR Evaluation Report
66 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
SAR SIMULTANEOUS TRANSMISSION DESCRIPTION
Simultaneous Transmission:
Description of Simultaneous Transmit Capabilities
Transmitter Combination
Simultaneous?
Hotspot?
WWAN(GSM/CDMA/WCDMA/LTE) + Bluetooth
√
×
WWAN(GSM/CDMA/WCDMA/LTE) + Bluetooth
√
√
Simultaneous and Hotspot SAR test exclusion considerations:
Mode(SAR1+SAR2)
GSM 850 +Bluetooth
PCS1900 +Bluetooth
CDMA 850 +Bluetooth
CDMA 1900 +Bluetooth
WCDMA Band
2+Bluetooth
WCDMA Band
5+Bluetooth
LTE Band 7+Bluetooth
LTE Band 41+Bluetooth
SAR Evaluation Report
Position
Reported SAR(W/kg)
ΣSAR <
1.6W/kg
Body Worn Back
Body Back
Body Worn Back
Body Back
Body Worn Back
Body Back
Body Worn Back
Body Back
SAR1
0.14
0.20
0.95
1.12
0.36
0.44
0.90
0.97
SAR2
0.04
0.04
0.04
0.04
0.04
0.04
0.04
0.04
Body Back
1.05
0.04
1.09
Body Back
0.18
0.04
0.22
Body Back
Body Back
0.37
0.25
0.04
0.04
0.41
0.29
0.18
0.24
0.99
1.16
0.40
0.48
0.94
1.01
67 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Mode(SAR1+SAR2)
GSM 850+ WLAN
PCS1900 + WLAN
CDMA 850+ WLAN
CDMA 1900 + WLAN
WCDMA Band 2+ WLAN
WCDMA Band 5+ WLAN
LTE Band 7+ WLAN
LTE Band 41+ WLAN
Position
Body Worn Back
Body Back
Body Right
Body Bottom
Body Worn Back
Body Back
Body Right
Body Bottom
Body Worn Back
Body Back
Body Right
Body Bottom
Body Worn Back
Body Back
Body Right
Body Bottom
Body Back
Body Right
Body Bottom
Body Back
Body Right
Body Bottom
Body Back
Body Right
Body Bottom
Body Back
Body Right
Body Bottom
Report No.: RSZ180529003-20A
Reported SAR(W/kg)
SAR1
0.14
0.20
0.07
0.18
0.95
1.12
0.90
0.47
0.36
0.44
0.19
0.34
0.90
0.97
0.64
0.35
1.05
0.96
0.54
0.18
0.11
0.24
0.37
0.32
0.21
0.25
0.09
0.10
SAR2
0.08
0.08
0.06
N/A
0.08
0.08
0.06
N/A
0.08
0.08
0.06
N/A
0.08
0.08
0.06
N/A
0.08
0.06
N/A
0.08
N/A
0.06
0.08
0.06
N/A
0.08
0.06
N/A
ΣSAR <
1.6W/kg
0.22
0.28
0.13
N/A
1.03
1.20
0.96
N/A
0.44
0.52
0.25
N/A
0.98
1.05
0.70
N/A
1.13
1.02
N/A
0.26
N/A
0.30
0.45
0.38
N/A
0.33
0.15
N/A
Note:
1. Hotspot mode SAR is measured for all edges and surfaces of the device with a transmitting antenna
located within 25 mm from that surface or edge; for the data modes, wireless technologies and frequency
bands supporting hotspot mode.
2. Hotspot Mode is not feasible during voice calls.
Conclusion:
Sum of SAR: ΣSAR ≤ 1.6 W/kg therefore simultaneous transmission SAR with Volume Scans is not
required.
SAR Evaluation Report
68 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
SAR Plots
Please Refer to the Attachment.
SAR Evaluation Report
69 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
APPENDIX A MEASUREMENT UNCERTAINTY
The uncertainty budget has been determined for the measurement system and is given in the following
Table.
Measurement uncertainty evaluation for IEEE1528-2013 SAR test
Source of
uncertainty
Tolerance/
uncertainty
±%
Probability
distribution
Divisor
ci
(1 g)
ci
(10 g)
Standard
uncertainty
± %, (1 g)
Standard
uncertainty
± %, (10 g)
Measurement system
Probe calibration
6.55
6.6
6.6
Axial Isotropy
4.7
√3
2.7
2.7
Hemispherical Isotropy
9.6
√3
0.0
0.0
Boundary effect
1.0
√3
0.6
0.6
Linearity
4.7
√3
2.7
2.7
Detection limits
1.0
√3
0.6
0.6
Readout electronics
0.3
0.3
0.3
Response time
0.0
√3
0.0
0.0
Integration time
0.0
√3
0.0
0.0
1.0
√3
0.6
0.6
1.0
√3
0.6
0.6
0.8
√3
0.5
0.5
6.7
√3
3.9
3.9
2.0
√3
1.2
1.2
RF ambient conditions –
noise
RF ambient
conditions–reflections
Probe positioner mech.
Restrictions
Probe positioning with
respect to phantom shell
Post-processing
Test sample related
Test sample positioning
Device holder
uncertainty
Drift of output power
2.8
2.8
2.8
6.3
6.3
6.3
5.0
√3
2.9
2.9
Phantom and set-up
Phantom uncertainty (shape
and thickness tolerances)
4.0
√3
2.3
2.3
Liquid conductivity target)
5.0
√3
0.64
0.43
1.8
1.2
Liquid conductivity meas.)
2.5
0.64
0.43
1.6
1.1
Liquid permittivity target)
5.0
√3
0.6
0.49
1.7
1.4
Liquid permittivity meas.)
2.5
0.6
0.49
1.5
1.2
12.2
12.0
24.3
23.9
Combined standard
uncertainty
Expanded uncertainty 95 %
confidence interval)
SAR Evaluation Report
RSS
70 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
Measurement uncertainty evaluation for IEC62209-2 SAR test
Source of
uncertainty
Tolerance/
uncertainty
±%
Probability
distribution
Divisor
ci
(1 g)
ci
(10 g)
Standard
uncertainty
± %, (1 g)
Standard
uncertainty
± %, (10 g)
Measurement system
Probe calibration
6.55
6.6
6.6
Axial Isotropy
4.7
√3
2.7
2.7
Hemispherical Isotropy
9.6
√3
0.0
0.0
Linearity
4.7
√3
2.7
2.7
Modulation Response
0.0
√3
0.0
0.0
Detection limits
1.0
√3
0.6
0.6
Boundary effect
1.0
√3
0.6
0.6
Readout electronics
0.3
0.3
0.3
Response time
0.0
√3
0.0
0.0
Integration time
0.0
√3
0.0
0.0
1.0
√3
0.6
0.6
1.0
√3
0.6
0.6
Probe positioner mech.
Restrictions
0.8
√3
0.5
0.5
Probe positioning with
respect to phantom shell
6.7
√3
3.9
3.9
Post-processing
2.0
√3
1.2
1.2
RF ambient conditions –
noise
RF ambient
conditions–reflections
Test sample related
Device holder Uncertainty
6.3
6.3
6.3
Test sample positioning
2.8
2.8
2.8
Power scaling
4.5
√3
2.6
2.6
Drift of output power
5.0
√3
2.9
2.9
Phantom and set-up
Phantom uncertainty (shape
and thickness tolerances)
4.0
√3
2.3
2.3
Algorithm for correcting SAR
for deviations in permittivity
and conductivity
1.9
0.84
1.1
0.9
Liquid conductivity (meas.)
2.5
0.64
0.43
1.6
1.1
Liquid permittivity (meas.)
2.5
0.6
0.49
1.5
1.2
Temp. unc. - Conductivity
1.7
√3
0.78
0.71
0.8
0.7
Temp. unc. - Permittivity
0.3
√3
0.23
0.26
0.0
0.0
12.2
12.1
24.5
24.2
Combined standard
uncertainty
Expanded uncertainty 95 %
confidence interval)
SAR Evaluation Report
RSS
71 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
APPENDIX B EUT TEST POSITION PHOTOS
Please Refer to the Attachment.
SAR Evaluation Report
72 of 73
Bay Area Compliance Laboratories Corp. (Dongguan)
Report No.: RSZ180529003-20A
APPENDIX C CALIBRATION CERTIFICATES
Please Refer to the Attachment.
***** END OF REPORT *****
SAR Evaluation Report
73 of 73
Download: IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Mirror Download [FCC.gov]IS9101 Intrinsically safe Tablet PC RF Exposure Info SAR Report_RSZ180529003-20A i.safe MOBILE GmbH
Document ID3951450
Application IDlc5/OsJ+P0Eu9irtz0yIqQ==
Document DescriptionSAR Test report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeRF Exposure Info
Display FormatAdobe Acrobat PDF - pdf
Filesize105.56kB (1319488 bits)
Date Submitted2018-08-03 00:00:00
Date Available2018-08-03 00:00:00
Creation Date2018-08-03 18:44:40
Producing SoftwareAcrobat Distiller 7.0 (Windows)
Document Lastmod2018-08-03 11:33:54
Document TitleSAR Report_RSZ180529003-20A
Document CreatorPScript5.dll Version 5.2
Document Author: DG06245

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : DG06245
Create Date                     : 2018:08:03 18:44:40+08:00
Modify Date                     : 2018:08:03 11:33:54-07:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Metadata Date                   : 2018:08:03 11:33:54-07:00
Format                          : application/pdf
Title                           : Microsoft Word - SAR Report_RSZ180529003-20A.doc
Creator                         : DG06245
Document ID                     : uuid:3b84a8ee-9fd9-4416-adae-d68c423a4605
Instance ID                     : uuid:c185f7a5-8a98-4c88-8300-89a34fb1b478
Page Count                      : 73