MNFLAME Monster FLAME RF Exposure Info RF Exposure ACOUSTMAX INTERNATIONAL CO., LTD

ACOUSTMAX INTERNATIONAL CO., LTD Monster FLAME

Page 1 of MNFLAME Monster FLAME RF Exposure Info RF Exposure ACOUSTMAX INTERNATIONAL CO., LTD
Page 2 of MNFLAME Monster FLAME RF Exposure Info RF Exposure ACOUSTMAX INTERNATIONAL CO., LTD
Page 3 of MNFLAME Monster FLAME RF Exposure Info RF Exposure ACOUSTMAX INTERNATIONAL CO., LTD
Page 4 of MNFLAME Monster FLAME RF Exposure Info RF Exposure ACOUSTMAX INTERNATIONAL CO., LTD

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AAIN-MNFLAME
FCC RF Exposure Evaluation
1.
Product Information
FCC ID:
Product Description
Test Model
Additional Model No.
Model Declaration
Power Supply
Hardware Version
Software Version
Bluetooth Operation
Frequency
Bluetooth Version
2AAIN-MNFLAME
Monster FLAME
MNFLAME
DC 15V/2A by adapter
1.0
1.0
2402 – 2480 MHz
Bluetooth Channel Number
Bluetooth Channel Spacing
Bluetooth Modulation Type
Antenna Description
5G Frequency Range
Channel Number
Modulation Type
Antenna Description
Exposure category
EUT Type
Device Type
2.
V4.0
79 Channels for Bluetooth V4.0 (BT Classics)
40 Channels for Bluetooth V4.0 (BT LE)
1MHz for Bluetooth V4.0 (BT Classics)
2MHz for Bluetooth V4.0 (BT LE)
GFSK, π/4-DQPSK, 8DPSK for Bluetooth V4.0 (BT Classics)
GFSK, for Bluetooth V4.0 (BT LE)
PCB antenna, 4dBi (Max.)
5736MHz ~ 5814MHz
3 channels(5736MHz, 5762MHz, 5814MHz)
QPSK
Two same antenna,
PCB Antenna, 4dBi (max.)
General population/uncontrolled environment
Production Unit
Portable Device
Evaluation Method
According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test
exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures,
standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure
conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test
Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on
source-based time-averaged maximum conducted output power of the RF channel requiring evaluation,
adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure
conditions.22 The minimum test separation distance is determined by the smallest distance from the
antenna and radiating structures or outer surface of the device, according to the host form factor,
exposure conditions and platform requirements, to any part of the body or extremity of a user or
bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied
must be fully explained and justified by the operating configurations and exposure conditions of the
transmitter and applicable host platform requirements, typically in the SAR measurement or SAR
analysis report, according to the required published RF exposure KDB procedures. When no other RF
exposure testing or reporting is required, a statement of justification and compliance must be included
in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When
required, the device specific conditions described in the other published RF exposure KDB procedures
must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT
two-way radios, handsets, laptops & tablets etc.“
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 1 of 4
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AAIN-MNFLAME
[(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f
(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where:
• f (GHz) is the RF channel transmit frequency in GHz
• Power and distance are rounded to the nearest mW and mm before calculation
• The result is rounded to one decimal place for comparison
• 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below
The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for
transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is
< 5 mm, a distance of 5 mm according to f) in section 4.1 is applied to determine SAR test exclusion.
When one of the following test exclusion conditions is satisfied for all combinations of simultaneous
transmission configurations, further equipment approval is not required to incorporate transmitter
modules in host devices that operate in the mixed mobile and portable host platform exposure
conditions. The grantee is responsible for documenting this according to Class I permissive change
requirements. Antennas that qualify for standalone SAR test exclusion must apply the estimated
standalone SAR to determine simultaneous transmission test exclusion.
a)
The [∑ of (the highest measured or estimated SAR for each standalone antenna
configuration, adjusted for maximum tune-up tolerance) / 1.6 W/kg] + [∑ of MPE ratios] is ≤ 1.0.
b)
The SAR to peak location separation ratios of all simultaneously transmitting
antenna pairs operating in portable device exposure conditions are all ≤ 0.04, and the [∑ of MPE
ratios] is ≤ 1.0.
3.
Refer Evaluation Method
ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency
Electromagnetic Fields, 3 kHz to 300 GHz.
FCC KDB publication 447498 D01 General RF Exposure Guidance v06: Mobile and Portable Devices RF
Exposure Procedures and Equipment Authorization Policies.
FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits.
FCC CFR 47 part2 2.1093: Radiofrequency radiation exposure evaluation: portable devices
4.
Conducted Power Results
4.1
Test Setup Block Diagram
4.2
Test Equipment
Item
Kind of Equipment
Power Meter
Power Sensor
Manufacturer
R&S
R&S
Type No.
NRVS
NRV-Z32
Serial No.
100444
10057
Calibrated until
2019-06-15
2019-06-15
Remark: all calibration period of equipment list is one year.
4.3
Test Procedure
a.
The EUT was directly connected to the power meter and antenna output port
as show in the block diagram Test Setup;
b.
Setup EUT work at duty cycle more than 98%;
c.
Read power sensor values in RMS detector;
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 2 of 4
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2AAIN-MNFLAME

Mode
Channel
Frequency(MHz)
39
78
39
78
39
78
19
39
2402
2441
2480
2402
2441
2480
2402
2441
2480
2402
2440
2480
GFSK
π/4DQPSK
8DPSK
GFSK – BT LE
5.
Average Conducted Output Power
(dBm)
-1.346
0.727
-2.140
-2.110
0.010
-2.976
-2.016
0.010
-2.920
-2.929
-2.299
-3.071
Manufacturing Tolerance
Channel
Target (dBm)
Tolerance ±(dB)
Channel
Target (dBm)
Tolerance ±(dB)
Channel
Target (dBm)
Tolerance ±(dB)
Channel
Target (dBm)
Tolerance ±(dB)
6.
GFSK (Average)
Channel 0
Channel 39
-1.0
0.0
1.0
1.0
π/4-DQPSK (Average)
Channel 0
Channel 39
-2.0
0.0
1.0
1.0
8DPSK (Average)
Channel 0
Channel 39
-2.0
0.0
1.0
1.0
GFSK – BT LE (Average)
Channel 0
Channel 19
-2.0
-2.0
1.0
1.0
Channel 78
-2.0
1.0
Channel 78
-2.0
1.0
Channel 78
-2.0
1.0
Channel 39
-3.0
1.0
Evaluation Results
6.1
Standalone Evaluation
Band/Mode
(GHz)
GFSK
π/4DQPSK
8DPSK
GFSK – BT LE
2.50
2.50
2.50
2.50
Antenna
Distance
(mm)
RF output power
dBm
mW
SAR Test Exclusion
Threshold
SAR Test
Exclusion
1.0
1.0
1.0
-1.0
1.2589
1.2589
1.2589
0.7943
0.4 < 3.0
0.4 < 3.0
0.4 < 3.0
0.2 < 3.0
Yes
Yes
Yes
Yes
Remark:
1. RF output power including tune up tolerance;
2. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to f) in section 4.1
of KDB 447498 is applied to determine SAR test exclusion.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 3 of 4
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
6.2
FCC ID: 2AAIN-MNFLAME
Simultaneous Transmission for SAR Exclusion
The sample only support one BT modular and one antenna, no need consider simultaneous
transmission.
7.
Conclusion
The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure
and SAR Exclusion Threshold per KDB 447498 v06.
----------------THE END OF REPORT---------------
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 4
Download: MNFLAME Monster FLAME RF Exposure Info RF Exposure ACOUSTMAX INTERNATIONAL CO., LTD
Mirror Download [FCC.gov]MNFLAME Monster FLAME RF Exposure Info RF Exposure ACOUSTMAX INTERNATIONAL CO., LTD
Document ID4198179
Application IDj/CuDcpXV7bKaQpA9gfYjQ==
Document DescriptionRF Exposure
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeRF Exposure Info
Display FormatAdobe Acrobat PDF - pdf
Filesize61.9kB (773740 bits)
Date Submitted2019-03-12 00:00:00
Date Available2019-03-12 00:00:00
Creation Date2019-02-18 10:19:21
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2019-02-18 10:19:21
Document TitleRF Exposure
Document CreatorMicrosoft® Office Word 2007
Document Author: User

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 4
Language                        : zh-CN
Author                          : User
Creator                         : Microsoft® Office Word 2007
Create Date                     : 2019:02:18 10:19:21+08:00
Modify Date                     : 2019:02:18 10:19:21+08:00
Producer                        : Microsoft® Office Word 2007