T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.

Tacx b.v. Wireless Bluetooth and ANT+ sensor

Page 1 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 2 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 3 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 4 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 5 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 6 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 7 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 8 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 9 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 10 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 11 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 12 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 13 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 14 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 15 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 16 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 17 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 18 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 19 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 20 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 21 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 22 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 23 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 24 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 25 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 26 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 27 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 28 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 29 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 30 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 31 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 32 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Page 33 of T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.

FCC and IC Test Report for Parts
15.247, 15.249, 15.209
and RSS-247, RSS Gen, RSS-210
Product name
: T2030
Applicant
: Tacx
FCC ID
: 2AAMI-T2030
IC ID
: 11353A-T2030
Test report No. : 180801587 003 Ver 3.00
Report number: 180801587 003 Ver 3.00
Laboratory information
Accreditation
Telefication complies with the accreditation criteria for test laboratories as laid down in ISO/IEC 17025:2005.
The accreditation covers the quality system of the laboratory as well as the specific activities as described in the
authorized annex bearing the accreditation number L021 and is granted on 30 November 1990 by the Dutch
Council For Accreditation (RvA: Raad voor Accreditatie).
Telefication is designated by the FCC as an Accredited Test Firm for compliance testing of equipment subject to
Certification under Parts 15 & 18. The Designation number is: NL0001.
Telefication is a Wireless Device Testing laboratory recognized by Innovation, Science and Economic
Development Canada to test to Canadian radio equipment requirements.
The Industry Canada registration number for the 3 meter test chamber of Telefication is: 4173A-1.
Documentation
The test report must always be reproduced in full; reproduction of an excerpt only is subject to written
approval of the testing laboratory. The documentation of the testing performed on the tested devices is
archived for 10 years at Telefication Netherlands.
Testing Location
Test Site
Telefication BV
Test Site location
Edisonstraat 12a
6902 PK Zevenaar
The Netherlands
Tel. +31889983600
Fax. +31316583189
Test Site FCC
NL0001
Page 1 of 32
Report number: 180801587 003 Ver 3.00
Revision History
Version
Date
Remarks
By
v0.50
11-12-2018
First draft
PvW
v1.00
15-02-2019
Initial release
PvW
v2.00
01-03-2019
Added field strength of fundamental to
ANT/ANT+ in clause 3.3.5
PVW
v3.00
06-03-2019
Updated emission designator for ANT+
from 1M00F7D to 1M00F1D
PVW
Page 2 of 32
Report number: 180801587 003 Ver 3.00
Table of Contents
Revision History .............................................................................................................................................. 2
Summary of Test results .................................................................................................................................. 5
General Description ................................................................................................................................. 6
1.1
Applicant................................................................................................................................................6
1.2
Manufacturer ........................................................................................................................................6
1.3
Tested Equipment Under Test (EUT) .....................................................................................................6
1.4
Product specifications of Equipment under test ...................................................................................7
1.5
Modification of the Equipment Under Test (EUT) .................................................................................7
1.6
Observations and remarks.....................................................................................................................7
1.7
Environmental conditions......................................................................................................................7
1.8
Measurement Standards .......................................................................................................................7
1.9
Applicable Standards .............................................................................................................................7
1.10
Conclusions ............................................................................................................................................8
Test configuration of the Equipment Under Test ..................................................................................... 9
2.1
Test mode ..............................................................................................................................................9
2.2
Tested channels and Data rates ............................................................................................................9
2.3
Test setups .............................................................................................................................................9
2.4
Equipment used in the test configuration ...........................................................................................10
2.5
Sample calculation ...............................................................................................................................10
Test results ............................................................................................................................................ 11
3.1
6dB bandwidth Measurement .............................................................................................................11
3.1.1
Limit.................................................................................................................................................11
3.1.2
Measurement instruments .............................................................................................................11
3.1.3
Test setup ........................................................................................................................................11
3.1.4
Test procedure ................................................................................................................................11
3.1.5
Test Results of the 6 dB bandwidth Measurement .........................................................................11
3.2
99% Occupied Bandwidth ....................................................................................................................12
3.2.1
Limit.................................................................................................................................................12
3.2.2
Measurement instruments .............................................................................................................12
3.2.3
Test setup ........................................................................................................................................12
3.2.4
Test procedure ................................................................................................................................12
3.2.5
Test results of the 99% occupied bandwidth measurement...........................................................12
3.2.6
Plots of the BLE V5.0 99% occupied bandwidth measurement ......................................................13
3.2.7
Plots of the ANT 99% Occupied bandwidth measurement .............................................................15
3.2.8
Plot of the ANT+ 99% occupied bandwidth measurement .............................................................16
3.3
3.3.1
Output Power Measurement ..............................................................................................................17
Limit.................................................................................................................................................17
Page 3 of 32
Report number: 180801587 003 Ver 3.00
3.3.2
Measurement instruments .............................................................................................................17
3.3.3
Test setup ........................................................................................................................................17
3.3.4
Test procedure ................................................................................................................................17
3.3.5
Test results of Output Power Measurement...................................................................................17
3.4
Power Spectral Density........................................................................................................................18
3.4.1
Limit.................................................................................................................................................18
3.4.2
Measurement instruments .............................................................................................................18
3.4.3
Test setup ........................................................................................................................................18
3.4.4
Test procedure ................................................................................................................................18
3.4.5
Test results of Power Spectral Density Measurement ....................................................................18
3.5
Band edge Measurement ....................................................................................................................19
3.5.1
Limit.................................................................................................................................................19
3.5.2
Measurement instruments .............................................................................................................19
3.5.3
Test setup ........................................................................................................................................19
3.5.4
Test procedure ................................................................................................................................19
3.5.5
Measurement Uncertainty ..............................................................................................................19
3.5.6
Plots of the Band edge Measurements ...........................................................................................19
3.6
Radiated Spurious Emissions Measurement .......................................................................................21
3.6.1
Limit.................................................................................................................................................21
3.6.2
Measurement instruments .............................................................................................................21
3.6.3
Test setup ........................................................................................................................................21
3.6.4
Test procedure ................................................................................................................................21
3.6.5
Notes ...............................................................................................................................................21
3.6.6
Plots of the Radiated Spurious Emissions (BLE V5.0) ......................................................................22
3.6.7
Plots of the Radiated Spurious Emissions (ANT) .............................................................................27
3.6.8
Measurement Uncertainty ..............................................................................................................32
Page 4 of 32
Report number: 180801587 003 Ver 3.00
Summary of Test results
FCC
ISED
Description
Section in
report
Verdict
15.247 (a)
RSS-247 5.2(a)
6dB Bandwidth
3.1
Pass
--
RSS-Gen 6.7
99% Bandwidth
3.2
Pass
15.247 (b)
RSS-247 5.1 (b)
RF output power
3.3
Pass
15.247 (e)
RSS-247 5.2 (b)
Power spectral density
3.4
Pass
15.247 (d)
RSS-247 5.5
Band edge
3.5
Pass
15.209 (a)
RSS-247 5.4
RSS-Gen 8.9
RSS-210 B.10
Radiated emissions
3.6
Pass
15.205 (a)
RSS-Gen 8.10
RSS-210 B.10
Spurious emissions in the restricted bands
3.6
Pass
Page 5 of 32
Report number: 180801587 003 Ver 3.00
1.1
General Description
Applicant
Client name:
Address
Zip code:
Telephone:
E-mail:
Contact name:
1.2
Manufacturer
Manufacturer name:
Address:
Zip code:
Telephone:
E-mail:
Contact name:
1.3
Tacx b.v.
Rijksstraatweg 52, Wassenaar, the Netherlands
2241BW
+31 (0)705119259
martin@tacx.nl
Martin Smits
Tacx b.v.
Rijksstraatweg 52, Wassenaar, the Netherlands
2241BW
+31 (0)705119259
martin@tacx.nl
Martin Smits
Tested Equipment Under Test (EUT)
Product name:
Brand name:
Product type:
FCC ID:
IC ID
Software version:
Hardware version:
Date of receipt
Tests started:
Testing ended:
T2030
Tacx
Power meter
2AAMI-T2030
11353A-T2030
-V08
15-10-2018
15-10-2018
14-02-2019
Page 6 of 32
Report number: 180801587 003 Ver 3.00
1.4
Product specifications of Equipment under test
TX Frequency range (MHz)
BLE V5.0: 2400 – 2483.5
ANT: 2400 – 2483.5
ANT+: 2450 and 2457 MHz1
RX frequency range (MHz)
BLE V5.0: 2400 – 2483.5
ANT: 2400 – 2483.5
ANT+: 2450 and 2457 MHz1
Maximum output power to antenna (dBm)
-0.68
Antenna type
Ceramic chip antenna
Antenna gain (dBi)
-2.0
Type of modulation
ANT; ANT+: GFSK
BLE V5.0: GFSK
Emission designator BLE (V5.0)
2M21F7D
Emission designator ANT+
1M00F1D
Note 1: ANT+ uses the same modulation techniques and transmission power as ANT. Measurements on ANT
are considered representative for all ANT+ frequencies. See clause 3.2.8 for a comparison of the signals.
1.5
Modification of the Equipment Under Test (EUT)
The manufacturer provided both a radiated sample and a conducted sample for radio testing.
1.6
Observations and remarks
For the ANT radio, only RF power, 99% occupied bandwidth and radiated spurious emissions tests are
applicable.
Measurements of the ANT technology are considered representative for all frequencies of the ANT+
technology because ANT+ uses the same modulation techniques and transmission power as ANT.
The EUT uses ANT+ when possible, but switches to ANT when communicating with a non-ANT+ device.
For the BLE V5.0 radio, all tests in this test report are applicable.
Spurious emissions in the 9 kHz – 30 MHz range are not reported as these emissions are more than 20 dB
below the transmission level.
1.7
Environmental conditions
Test date
Ambient temperature
Humidity
1.8
31-10-2018
19.2 °C
42.8 %
01-11-2018
20.3 °C
41.8 %
14-02-2019
20.3 °C
39.7 %
Measurement Standards
•
1.9
ANSI C63.10:2013
Applicable Standards
According to the specifications of the manufacturer, the EUT must comply with the requirements of the
following standards:
•
•
FCC Part 15 Subpart C §15.247, §15.249, §15.209
RSS-247 Issue 2, RSS-Gen Issue 5, RSS-210 Issue 9
Page 7 of 32
Report number: 180801587 003 Ver 3.00
1.10 Conclusions
The sample of the product showed NO NON-COMPLIANCES to the specifications stated in paragraph 1.9 of this
report.
The results of the test as stated in this report, are exclusively applicable to the product items as identified in this
report. Telefication accepts no responsibility for any properties of product items in this test report, which are
not supported by the tests as specified in paragraph 1.9 “Applicable standards”.
All tests are performed by:
Name
: P. van Wanrooij, BASc
Review of test methods and report by:
Name
: ing. R. van Barneveld
The above conclusions have been verified by the following signatory:
Date
: 06-03-2019
Name
: ing. K.A. Roes
Function
: Coordinator Radio Laboratory
Signature
Page 8 of 32
Report number: 180801587 003 Ver 3.00
2.1
Test configuration of the Equipment Under Test
Test mode
The applicant provided test mode firmware for the EUT, in which it was possible to configure the EUT into
different test channels.
2.2
Tested channels and Data rates
2 Mbps BLE V5.0 has not been tested because the RF chip of the EUT only supports 1 Mbps BLE V5.0.
Technology
Bluetooth Low Energy V5.0
Technology
ANT
Technology
ANT+
2.3
Channels
1 (Low)
18 (Mid)
39 (High)
Data rate
1 Mbps
1 Mbps
1 Mbps
Frequency (MHz)
2402
2440
2480
Channels
1 (Low)
39 (Mid)
78 (High)
Data rate
1 Mbps
1 Mbps
1 Mbps
Frequency (MHz)
2402
2440
2480
Channels
--
Data rate
1 Mbps
Frequency (MHz)
2457
Test setups
Radiated emissions test setup 30 MHz - 1 GHz
Page 9 of 32
Report number: 180801587 003 Ver 3.00
Radiated emissions test setup above 1 GHz
2.4
Equipment used in the test configuration
Description
Radiated emission measurement
system
Conducted emission radio
equipment
Test setup number
TS 00004
Used at paragraphs
3.6
TS 00008
3.1 – 3.5
Description
Manufacturer
Model
Equipment ID
Spectrum analyser
High pass filter
Software
Rohde & Schwarz
Wainwright
DARE Instruments
FSV40
WHK10-2520-30
Radimation
2018.1.5
TE 11160
TE 11146
--
2.5
Used at
paragraphs
3.1 – 3.5
3.6
3.6
Sample calculation
Field Strength Measurement example:
Frequency (GHz)
Polarization
7,32
Horizontal
Height(m)
Peak (dBµV/m)
47.9
The following relation applies:
E (dBµV/m) = U(dBµV) + AF (dB/m) – G (dB) + CL (dB)
Where:
E = Electric field strength
U = Measuring receiver voltage
AF = Antenna factor
G = Gain of the pre-amplifier
CL = Cable loss
(52.5 = 48.12 + 36.1 - 37.42 + 5.7)
Page 10 of 32
Report number: 180801587 003 Ver 3.00
Test results
3.1
6dB bandwidth Measurement
3.1.1 Limit
The minimum 6 dB Bandwidth shall be at least 500 kHz.
3.1.2 Measurement instruments
The measurement instruments are listed in chapter 2.4 of this report.
3.1.3 Test setup
The test setup is as shown in chapter 2.3 of this report.
3.1.4 Test procedure
Tests according to ANSI C63.10.
IRN 017 - Occupied bandwidth (Hz) Method 4 – DTS Bandwidth.
3.1.5 Test Results of the 6 dB bandwidth Measurement
Technology Std.
Channel
Bluetooth Low energy
V5.0
18
39
Uncertainty
Frequency
(MHz)
2402
2440
2480
Data rate
1 Mbps
1 Mbps
1 Mbps
± 36.2 kHz
6dB bandwidth
(kHz)
1133.8
1129.5
1133.8
Page 11 of 32
Report number: 180801587 003 Ver 3.00
3.2
99% Occupied Bandwidth
3.2.1 Limit
According to RSS-Gen 6.7.
3.2.2 Measurement instruments
The measurement instruments are listed in chapter 2.4 of this report.
3.2.3 Test setup
The test setup is as shown in chapter 2.3 of this report.
3.2.4 Test procedure
IRN 017 - Occupied bandwidth (Hz) Method 1 – XX % power bandwidth.
1.
2.
3.
4.
Set the centre frequency to the nominal EUT channel centre frequency
Set span = 1.5 times to 0.5 times the Occupied Bandwidth
Set VBW ≥ 3x RBW
Video averaging is not permitted. Where practical, detection and single sweep mode shall be used.
Otherwise, peak detection and max hold mode (until the trace stabilizes) shall be used.
3.2.5 Test results of the 99% occupied bandwidth measurement
Technology Std.
Channel
Bluetooth Low energy
V5.0
18
39
Frequency
(MHz)
2402
2440
2480
Uncertainty
Technology Std.
Channel
ANT
39
78
Frequency
(MHz)
2402
2440
2480
Uncertainty
Technology Std.
ANT+
Uncertainty
Channel
--
Frequency
(MHz)
2457
Data rate
1 Mbps
1 Mbps
1 Mbps
± 12 kHz
Data rate
1 Mbps
1 Mbps
1 Mbps
± 12 kHz
Data rate
1 Mbps
± 12 kHz
99% bandwidth
(kHz)
2185
2200
2214
99% bandwidth
(kHz)
1187
1187
1187
99% bandwidth
(kHz)
1187
Page 12 of 32
Report number: 180801587 003 Ver 3.00
3.2.6 Plots of the BLE V5.0 99% occupied bandwidth measurement
Channel 1
Channel 18
Page 13 of 32
Report number: 180801587 003 Ver 3.00
Channel 39
Page 14 of 32
Report number: 180801587 003 Ver 3.00
3.2.7 Plots of the ANT 99% Occupied bandwidth measurement
Channel 1
Channel 39
Page 15 of 32
Report number: 180801587 003 Ver 3.00
Channel 78
3.2.8 Plot of the ANT+ 99% occupied bandwidth measurement
2457 MHz
Page 16 of 32
Report number: 180801587 003 Ver 3.00
3.3
Output Power Measurement
3.3.1 Limit
BLE V5.0: For systems using digital modulation in the 2400-2483.5 MHz, the limit for the peak output power is
30 dBm. If transmitting antenna of directional gain greater than 6 dBi is used, the peak output power from the
intentional radiator shall be reduced below the above stated value by the amount in dB that the directional
gain of the antenna exceeds 6 dBi. In case of point to point operation, the limit has to be reduced by 1 dB for
every 3 dB that the directional gain of the antenna exceeds 6 dBi.
ANT/ANT+: Field strength of fundamental: 50 mV/m @ 3m.
3.3.2 Measurement instruments
The measurement instruments are listed in chapter 2.4 of this report.
3.3.3 Test setup
The test setup is as shown in chapter 2.3 of this report.
3.3.4 Test procedure
The testing follows ANSI C63.10.
IRN 014 - RF power (W) - Method 1 – AVGSA (DTS) according to ANSI C63.10.
3.3.5 Test results of Output Power Measurement
Technology Std.
Channel
Bluetooth Low Energy
V5.0
18
39
Peak method
Frequency
(MHz)
2402
2440
2480
Uncertainty
Technology Std.
Channel
Frequency
(MHz)
ANT
39
78
2402
2440
2480
Channel
Frequency
(MHz)
--
2457
Uncertainty
Technology Std.
ANT+
Uncertainty
Data rate
1 Mbps
1 Mbps
1 Mbps
±0.71 dB
Data rate
1 Mbps
1 Mbps
1 Mbps
±0.71 dB
Data rate
1 Mbps
±0.71 dB
Peak output
power (dBm)
-10.10
-10.40
-9.94
Peak output
power (dBm)
-10.13
Peak output power
(dBm)
-1.31
-0.93
-0.68
Field strength of
fundamental
(mV/m @ 3m)
0.018
0.017
0.18
Field strength of
fundamental
(mV/m @ 3m)
0.018
Page 17 of 32
Report number: 180801587 003 Ver 3.00
3.4
Power Spectral Density
3.4.1 Limit
The peak power spectral density shall not be greater than 8 dBm in any 3 kHz band at any time interval of
continuous transmission.
3.4.2 Measurement instruments
The measurement instruments are listed in chapter 2.4 of this report.
3.4.3 Test setup
The test setup is as shown in chapter 2.3 of this report.
3.4.4 Test procedure
The testing follows ANSI C63.10.
IRN 030 - Spectral power density (W per n.Hz) - Method 5 – Peak method PKPSD (PSD in 3 kHz band).
3.4.5 Test results of Power Spectral Density Measurement
Technology Std.
Channel
Bluetooth Low
Energy V5.0
18
39
Uncertainty
Peak Power spectral density
Frequency
Data rate
(MHz)
2402
1 Mbps
2440
1 Mbps
2480
1 Mbps
±2.0 dB
PSD/3 kHz
(dBm)
-19.2
-18.8
-18.7
Page 18 of 32
Report number: 180801587 003 Ver 3.00
3.5
Band edge Measurement
3.5.1 Limit
Band edge:
At the edge of the authorized band the RF power shall be at least 20 dB down.
3.5.2 Measurement instruments
The measurement instruments are listed in chapter 2.4 of this report.
3.5.3 Test setup
The test setup is as shown in chapter 2.3 of this report.
3.5.4 Test procedure
According to ANSI C63.10.
IRN 026 - Radiated electrical disturbance (V per m) Method 6 – Radiated electrical disturbance at the
Authorized band edge.
3.5.5 Measurement Uncertainty
± 5.7 dB.
3.5.6 Plots of the Band edge Measurements
See next page.
Page 19 of 32
Report number: 180801587 003 Ver 3.00
BLE V5.0 Lower band edge (Channel 1)
BLE V5.0 Upper band edge (Channel 39)
Page 20 of 32
Report number: 180801587 003 Ver 3.00
3.6
Radiated Spurious Emissions Measurement
3.6.1 Limit
The emissions from an intentional radiator shall not exceed the field strength levels specified in the
following table:
15.209
Frequency (MHz)
0.009 – 0.490
0.490 – 1.705
1.705 - 30
30 -88
88 - 216
216-960
Above 960
Field strength (µV/m)
2400/F(kHz)
24000/F(kHz)
30
100
150
200
500
Measurement distance(m)
300
30
30
3.6.2 Measurement instruments
The measurement instruments are listed in chapter 2.4 of this report.
3.6.3 Test setup
The test setup is as shown in chapter 2.3 of this report.
3.6.4 Test procedure
Spurious emissions in the 9 kHz – 30 MHz range are not reported as these emissions are more than 20 dB
below the transmission level.
The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak
detector except for the frequency bands 9–90 kHz, 110–490 kHz and above 1000 MHz.
Radiated emission limits in these three bands are based on measurements employing an average detector.
Other details are according ANSI C63.10.
IRN 026 - Radiated electrical disturbance (V per m) Method 1 – 30 MHz – 1 GHz in SAR.
IRN 026 - Radiated electrical disturbance (V per m) Method 2 – 1 - 18 GHz in SAR.
IRN 026 - Radiated electrical disturbance (V per m) Method 3 – 18 - 26.5 GHz in SAR.
3.6.5 Notes
•
In the frequency range of 1 – 26 GHz the green trace is measured using a peak detector and the red
trace is measured using an average detector. The top limit line represent the peak limit and the
bottom limit represents the average limit
Page 21 of 32
Report number: 180801587 003 Ver 3.00
3.6.6 Plots of the Radiated Spurious Emissions (BLE V5.0)
30 MHz to 1 GHz
Vertical polarization
65
15.209/15.247
RBW : 100 kHz, Vertical Max Peak
60
55
50
Low ch
Electrical Field (dBµV/m)
45
40
35
30
25
20
15
10
30 M
50 M
100 M
200 M
300 M
500 M
1G
300 M
500 M
1G
300 M
500 M
1G
Frequency (Hz)
65
15.209/15.247
RBW : 100 kHz, Vertical Max Peak
60
55
50
Mid ch
Electrical Field (dBµV/m)
45
40
35
30
25
20
15
10
30 M
50 M
100 M
200 M
Frequency (Hz)
65
15.209/15.247
RBW : 100 kHz, Vertical Max Peak
60
55
50
High ch
Electrical Field (dBµV/m)
45
40
35
30
25
20
15
10
30 M
50 M
100 M
200 M
Frequency (Hz)
Page 22 of 32
Report number: 180801587 003 Ver 3.00
30 MHz to 1 GHz
Horizontal polarization
65
15.209/15.247
RBW : 100 kHz, Horizontal Max Peak
60
55
50
Low ch
Electrical Field (dBµV/m)
45
40
35
30
25
20
15
10
30 M
50 M
100 M
200 M
300 M
500 M
1G
300 M
500 M
1G
300 M
500 M
1G
Frequency (Hz)
65
15.209/15.247
RBW : 100 kHz, Horizontal Max Peak
60
55
50
Mid ch
Electrical Field (dBµV/m)
45
40
35
30
25
20
15
10
30 M
50 M
100 M
200 M
Frequency (Hz)
65
15.209/15.247
RBW : 100 kHz, Horizontal Max Peak
60
55
50
High ch
Electrical Field (dBµV/m)
45
40
35
30
25
20
15
10
30 M
50 M
100 M
200 M
Frequency (Hz)
Page 23 of 32
Report number: 180801587 003 Ver 3.00
1 GHz to 18 GHz
Vertical polarization
Limit Average 1 - 18 GHz
Limit Peak 1 - 18 GHz
RBW : 1 MHz, Vertical Max Average
RBW: 1 MHz, Vertical Max Peak
80
70
Low ch
Electrical Field (dBµV/m)
60
50
40
30
20
10
1G
2G
3G
5G
10 G
18 G
Frequency (Hz)
Limit Average 1 - 18 GHz
Limit Peak 1 - 18 GHz
RBW : 1 MHz, Vertical Max Average
RBW: 1 MHz, Vertical Max Peak
80
70
Mid ch
Electrical Field (dBµV/m)
60
50
40
30
20
10
1G
2G
3G
5G
10 G
18 G
Frequency (Hz)
Limit Average 1 - 18 GHz
Limit Peak 1 - 18 GHz
RBW : 1 MHz, Vertical Max Average
RBW: 1 MHz, Vertical Max Peak
80
70
High ch
Electrical Field (dBµV/m)
60
50
40
30
20
10
1G
2G
3G
5G
10 G
18 G
Frequency (Hz)
Page 24 of 32
Report number: 180801587 003 Ver 3.00
1 GHz to 18 GHz
Horizontal polarization
Limit Average 1 - 18 GHz
Limit Peak 1 - 18 GHz
RBW : 1 MHz, Horizontal Max Average
RBW: 1 MHz, Horizontal Max Peak
80
70
Low ch
Electrical Field (dBµV/m)
60
50
40
30
20
10
1G
2G
3G
5G
10 G
18 G
Frequency (Hz)
Limit Average 1 - 18 GHz
Limit Peak 1 - 18 GHz
RBW : 1 MHz, Horizontal Max Average
RBW: 1 MHz, Horizontal Max Peak
80
70
Mid ch
Electrical Field (dBµV/m)
60
50
40
30
20
10
1G
2G
3G
5G
10 G
18 G
Frequency (Hz)
Limit Average 1 - 18 GHz
Limit Peak 1 - 18 GHz
RBW : 1 MHz, Horizontal Max Average
RBW: 1 MHz, Horizontal Max Peak
80
70
High ch
Electrical Field (dBµV/m)
60
50
40
30
20
10
1G
2G
3G
5G
10 G
18 G
Frequency (Hz)
Page 25 of 32
Report number: 180801587 003 Ver 3.00
18 GHz to 26 GHz
Vertical polarization
85
Limit Average 18 - 26 GHz
Limit Peak 18 - 26 GHz
RBW: 100 kHz, Vertical Max Average
RBW: 100 kHz, Vertical Max Peak
80
75
70
High ch
Electrical Field (dBµV/m)
65
60
55
50
45
40
35
30
25
18 G
19 G
20 G
21 G
22 G
23 G
24 G
25 G
26 G
25 G
26 G
Frequency (Hz)
Horizontal polarization
85
Limit Average 18 - 26 GHz
Limit Peak 18 - 26 GHz
RBW: 100 kHz, Horizontal Max Average
RBW : 100 kHz, Horizontal Max Peak
80
75
70
High ch
Electrical Field (dBµV/m)
65
60
55
50
45
40
35
30
25
18 G
19 G
20 G
21 G
22 G
23 G
24 G
Frequency (Hz)
Page 26 of 32
Report number: 180801587 003 Ver 3.00
3.6.7 Plots of the Radiated Spurious Emissions (ANT)
30 MHz to 1 GHz
Vertical polarization
65
15.209/15.247
RBW : 100 kHz, Vertical Max Peak
60
55
50
Low ch
Electrical Field (dBµV/m)
45
40
35
30
25
20
15
10
30 M
50 M
100 M
200 M
300 M
500 M
1G
300 M
500 M
1G
300 M
500 M
1G
Frequency (Hz)
65
15.209/15.247
RBW : 100 kHz, Vertical Max Peak
60
55
50
Mid ch
Electrical Field (dBµV/m)
45
40
35
30
25
20
15
10
30 M
50 M
100 M
200 M
Frequency (Hz)
65
15.209/15.247
RBW : 100 kHz, Vertical Max Peak
60
55
50
High ch
Electrical Field (dBµV/m)
45
40
35
30
25
20
15
10
30 M
50 M
100 M
200 M
Frequency (Hz)
Page 27 of 32
Report number: 180801587 003 Ver 3.00
30 MHz to 1 GHz
Horizontal polarization
65
15.209/15.247
RBW : 100 kHz, Horizontal Max Peak
60
55
50
Low ch
Electrical Field (dBµV/m)
45
40
35
30
25
20
15
10
30 M
50 M
100 M
200 M
300 M
500 M
1G
300 M
500 M
1G
300 M
500 M
1G
Frequency (Hz)
65
15.209/15.247
RBW : 100 kHz, Horizontal Max Peak
60
55
50
Mid ch
Electrical Field (dBµV/m)
45
40
35
30
25
20
15
10
30 M
50 M
100 M
200 M
Frequency (Hz)
65
15.209/15.247
RBW : 100 kHz, Horizontal Max Peak
60
55
50
High ch
Electrical Field (dBµV/m)
45
40
35
30
25
20
15
10
30 M
50 M
100 M
200 M
Frequency (Hz)
Page 28 of 32
Report number: 180801587 003 Ver 3.00
1 GHz to 18 GHz
Vertical polarization
Limit Average 1 - 18 GHz
Limit Peak 1 - 18 GHz
RBW : 1 MHz, Vertical Max Average
RBW: 1 MHz, Vertical Max Peak
80
70
Low ch
Electrical Field (dBµV/m)
60
50
40
30
20
10
1G
2G
3G
5G
10 G
18 G
Frequency (Hz)
Limit Average 1 - 18 GHz
Limit Peak 1 - 18 GHz
RBW : 1 MHz, Vertical Max Average
RBW: 1 MHz, Vertical Max Peak
80
70
Mid ch
Electrical Field (dBµV/m)
60
50
40
30
20
10
1G
2G
3G
5G
10 G
18 G
Frequency (Hz)
Limit Average 1 - 18 GHz
Limit Peak 1 - 18 GHz
RBW : 1 MHz, Vertical Max Average
RBW: 1 MHz, Vertical Max Peak
80
70
High ch
Electrical Field (dBµV/m)
60
50
40
30
20
10
1G
2G
3G
5G
10 G
18 G
Frequency (Hz)
Page 29 of 32
Report number: 180801587 003 Ver 3.00
1 GHz to 18 GHz
Horizontal polarization
Limit Average 1 - 18 GHz
Limit Peak 1 - 18 GHz
RBW : 1 MHz, Horizontal Max Average
RBW: 1 MHz, Horizontal Max Peak
80
70
60
Low ch
Electrical Field (dBµV/m)
50
40
30
20
10
1G
2G
3G
5G
10 G
18 G
Frequency (Hz)
Limit Average 1 - 18 GHz
Limit Peak 1 - 18 GHz
RBW : 1 MHz, Horizontal Max Average
RBW: 1 MHz, Horizontal Max Peak
80
70
Mid ch
Electrical Field (dBµV/m)
60
50
40
30
20
10
1G
2G
3G
5G
10 G
18 G
Frequency (Hz)
Limit Average 1 - 18 GHz
Limit Peak 1 - 18 GHz
RBW : 1 MHz, Horizontal Max Average
RBW: 1 MHz, Horizontal Max Peak
80
70
High ch
Electrical Field (dBµV/m)
60
50
40
30
20
10
1G
2G
3G
5G
10 G
18 G
Frequency (Hz)
Page 30 of 32
Report number: 180801587 003 Ver 3.00
18 GHz to 26 GHz
Vertical polarization
85
Limit Average 18 - 26 GHz
Limit Peak 18 - 26 GHz
RBW: 100 kHz, Vertical Max Average
RBW: 100 kHz, Vertical Max Peak
80
75
70
Electrical Field (dBµV/m)
65
Low ch
60
55
50
45
40
35
30
25
18 G
19 G
20 G
21 G
22 G
23 G
24 G
25 G
26 G
25 G
26 G
Frequency (Hz)
18 GHz to 26 GHz
Horizontal polarization
85
Limit Average 18 - 26 GHz
Limit Peak 18 - 26 GHz
RBW: 100 kHz, Horizontal Max Average
RBW : 100 kHz, Horizontal Max Peak
80
75
70
Low ch
Electrical Field (dBµV/m)
65
60
55
50
45
40
35
30
25
18 G
19 G
20 G
21 G
22 G
23 G
24 G
Frequency (Hz)
Frequency
Polarization
7,206 GHz
Vertical
Frequency
7,32 GHz
ANT Measured peaks Vertical 1 – 18 GHz Low channel
Height
Peak
Average Peak
Average
Limit
Limit
3m
54,5
49,6
74
54
dBµV/m dBµV/m dBµV/m dBµV/m
Peak
Difference
-19,5 dB
Average
Difference
-4,4 dB
ANT Measured peaks Horizontal 1 – 18 GHz Middle channel
Polarization Height
Peak
Average Peak
Average Peak
Limit
Limit
Difference
Vertical
1,5 m
47,9
40,1
74
54
-26,1 dB
dBµV/m dBµV/m dBµV/m dBµV/m
Average
Difference
-13,9 dB
Page 31 of 32
Report number: 180801587 003 Ver 3.00
3.6.8 Measurement Uncertainty
Measurement uncertainty Radiated emissions below 1 GHz
Horizontal polarization
30 – 200 MHz
4.5 dB
200 – 1000 MHz
3.6 dB
Vertical polarization
30 – 200 MHz
5.4 dB
200 – 1000 MHz
4.6 dB
Measurement uncertainty Radiated emissions above 1 GHz
1000- 18000 MHZ
5.7 dB
18000 – 26000 MHZ
3.9 dB
Page 32 of 32
Download: T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Mirror Download [FCC.gov]T2030 Wireless Bluetooth and ANT+ sensor Test Report 180801587 003 Ver 3.00x Tacx b.v.
Document ID4191772
Application IDvtuMF4Zxwk61wuJGTIwiag==
Document DescriptionTest Report_DXX
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize253.91kB (3173872 bits)
Date Submitted2019-03-06 00:00:00
Date Available2019-03-06 00:00:00
Creation Date2019-03-06 12:07:00
Producing SoftwarepdfFactory Pro 4.63 (Windows Server 2008 R2 Enterprise x64)
Document Lastmod0000-00-00 00:00:00
Document Title180801587 003 Ver 3.00x
Document CreatorpdfFactory Pro www.pdffactory.com
Document Author: kiw-adm-av

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Fill forms, Print high-res
Title                           : 180801587 003 Ver 3.00.docx
Author                          : kiw-adm-av
Creator                         : pdfFactory Pro www.pdffactory.com
Producer                        : pdfFactory Pro 4.63 (Windows Server 2008 R2 Enterprise x64)
Create Date                     : 2019:03:06 12:07:00+01:00
Page Count                      : 33
Page Layout                     : SinglePage