MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.

CONEDERA S.A. Tablet pc

Page 1 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 2 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 3 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 4 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 5 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 6 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 7 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 8 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 9 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 10 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 11 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 12 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 13 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 14 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 15 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 16 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 17 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 18 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 19 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 20 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 21 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Page 22 of MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.

Report No.: AGC02399180201FE04
Page 21 of 42
9.4. LIMITS AND MEASUREMENT RESULT
LIMITS AND MEASUREMENT RESULT
Measurement Result
Applicable Limits
In any 100 KHz Bandwidth Outside the
frequency band in which the spread spectrum
intentional radiator is operating, the radio frequency
power that is produce by the intentional radiator
shall be at least 20 dB below that in 100KHz
bandwidth within the band that contains the highest
level of the desired power.
In addition, radiation emissions which fall in the
restricted bands, as defined in §15.205(a), must also
comply with the radiated emission limits specified
in§15.209(a))
Test Data
Criteria
At least -20dBc than the limit
Specified on the BOTTOM
Channel
PASS
At least -20dBc than the limit
Specified on the TOP Channel
PASS
Report No.: AGC02399180201FE04
Page 22 of 42
Test Graph
11B-LCH
11B-LCH
11B-LCH
11B-MCH
11B-MCH
11B-MCH
Report No.: AGC02399180201FE04
Page 23 of 42
11B-HCH
11B-HCH
11B-HCH
11G-LCH
11G-LCH
11G-LCH
Report No.: AGC02399180201FE04
Page 24 of 42
11G-MCH
11G-MCH
11G-MCH
11G-HCH
11G-HCH
11G-HCH
Report No.: AGC02399180201FE04
Page 25 of 42
11nHT20-LCH
11nHT20-LCH
11nHT20-LCH
11nHT20-MCH
11nHT20-MCH
11nHT20-MCH
Report No.: AGC02399180201FE04
Page 26 of 42
11nHT20-HCH
11nHT20-HCH
11nHT20-HCH
11nHT40-LCH
11nHT40-LCH
11nHT40-LCH
Report No.: AGC02399180201FE04
Page 27 of 42
11nHT40-MCH
11nHT40-MCH
11nHT40-MCH
11nHT40-HCH
11nHT40-HCH
11nHT40-HCH
Report No.: AGC02399180201FE04
Page 28 of 42
10. MAXIMUM CONDUCTED OUTPUT POWER SPECTRAL DENSITY
10.1 MEASUREMENT PROCEDURE
(1). Connect EUT RF output port to the Spectrum Analyzer through an RF attenuator
(2). Set the EUT Work on the top, the middle and the bottom operation frequency individually.
(3). Set SPA Trace 1 Max hold, then View.
Note: The method of AVGPSD in the KDB 558074 item 10.3 was used in this testing.
10.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)
Refer To Section 8.2.
10.3 MEASUREMENT EQUIPMENT USED
Refer To Section 6.
Report No.: AGC02399180201FE04
Page 29 of 42
10.4 LIMITS AND MEASUREMENT RESULT
Mode
11b
11g
11nHT20
11NHT40
Channel
PSD [dBm/3kHz]
Limit[dBm/3kHz]
Verdict
LCH
-8.329
PASS
MCH
-7.927
PASS
HCH
-6.407
PASS
LCH
-11.136
PASS
MCH
-10.197
PASS
HCH
-10.417
PASS
LCH
-11.695
PASS
MCH
-11.136
PASS
HCH
-10.986
PASS
LCH
-14.073
PASS
MCH
-13.901
PASS
HCH
-12.974
PASS
Report No.: AGC02399180201FE04
Page 30 of 42
Test Graph
11b-LCH
11b-MCH
11b-HCH
11g-LCH
11g-MCH
11g-HCH
Report No.: AGC02399180201FE04
Page 31 of 42
11nHT20-LCH
11nHT20-MCH
11nHT20-HCH
11nHT40-LCH
11nHT40-MCH
11nHT40-HCH
Report No.: AGC02399180201FE04
Page 32 of 42
11. RADIATED EMISSION
11.1. MEASUREMENT PROCEDURE
1. The EUT was placed on the top of the turntable 0.8 or 1.5 meter above ground. The phase center of the
receiving antenna mounted on the top of a height-variable antenna tower was placed 3 meters far away
from the turntable.
2. Power on the EUT and all the supporting units. The turntable was rotated by 360 degrees to determine
the position of the highest radiation.
3. The height of the broadband receiving antenna was varied between one meter and four meters above
ground to find the maximum emissions field strength of both horizontal and vertical polarization.
4. For each suspected emissions, the antenna tower was scan (from 1 M to 4 M) and then the turntable was
rotated (from 0 degree to 360 degrees) to find the maximum reading.
5. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function with specified bandwidth
under Maximum Hold Mode.
6. For emissions above 1GHz, use 1MHz VBW and RBW for peak reading. Then 1MHz RBW and 10Hz
VBW for average reading in spectrum analyzer. Place the measurement antenna away from each area of
the EUT determined to be a source of emissions at the specified measurement distance, while keeping
the measurement antenna aimed at the source of emissions at each frequency of significant emissions,
with polarization oriented for maximum response. The measurement antenna may have to be higher or
lower than the EUT, depending on the radiation pattern of the emission and staying aimed at the emission
source for receiving the maximum signal. The final measurement antenna elevation shall be that which
maximizes the emissions. The measurement antenna elevation for maximum emissions shall be restricted
to a range of heights of from 1 m to 4 m above the ground or reference ground plane.
7. When the radiated emissions limits are expressed in terms of the average value of the emissions, and
pulsed operation is employed, the measurement field strength shall be determined by averaging over one
complete pulse train, including blanking intervals, as long as the pulse train does not exceed 0.1 seconds.
As an alternative (provided the transmitter operates for longer than 0.1 seconds) or in cases where the
pulse train exceeds 0.1 seconds, the measured field strength shall be determined from the average
absolute voltage during a 0.1 second interval during which the field strength is at its maximum values.
8.If the emissions level of the EUT in peak mode was 3 dB lower than the average limit specified, then
testing will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not
have 3 dB margin will be repeated one by one using the quasi-peak method for below 1GHz.
9. For testing above 1GHz, the emissions level of the EUT in peak mode was lower than average limit (that
means the emissions level in peak mode also complies with the limit in average mode), then testing will
be stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in
average mode again and reported.
10. In case the emission is lower than 30MHz, loop antenna has to be used for measurement and the
recorded data should be QP measured by receiver. High - Low scan is not required in this case.
Report No.: AGC02399180201FE04
Page 33 of 42
11.2. TEST SETUP
Radiated Emission Test-Setup Frequency Below 30MHz
RADIATED EMISSION TEST SETUP 30MHz-1000MHz
RADIATED EMISSION TEST SETUP ABOVE 1000MHz
Report No.: AGC02399180201FE04
Page 34 of 42
11.3. LIMITS AND MEASUREMENT RESULT
15.209(a) Limit in the below table has to be followed
Frequencies
(MHz)
Field Strength
(micorvolts/meter)
Measurement Distance
(meters)
0.009~0.490
2400/F(KHz)
300
0.490~1.705
24000/F(KHz)
30
1.705~30.0
30
30
30~88
100
88~216
150
216~960
200
Above 960
500
Note: All modes were tested For restricted band radiated emission,
the test records reported below are the worst result compared to other modes.
Report No.: AGC02399180201FE04
Page 35 of 42
11.4. TEST RESULT
RADIATED EMISSION BELOW 30MHZ
No emission found between lowest internal used/generated frequencies to 30MHz.
RADIATED EMISSION BELOW 1GHZ
RADIATED EMISSION TEST- (30MHZ-1GHZ) -HORIZONTAL
RESULT: PASS
Report No.: AGC02399180201FE04
Page 36 of 42
RADIATED EMISSION TEST- (30MHZ-1GHZ) -VERTICAL
RESULT: PASS
Note: 1. Factor=Antenna Factor + Cable loss, Margin= Result -Limit.
2. The “Factor” value can be calculated automatically by software of measurement system.
3. All test modes had been pre-tested. The 802.11b at low channel is the worst case and recorded in
the report.
Report No.: AGC02399180201FE04
Page 37 of 42
RADIATED EMISSION ABOVE 1GHZ
Frequency
Emission Level
Limits
Margin
Detector
(MHz)
(dBμV/m)
(dBμV/m)
(dB)
Type
Comment
TX 11b 2412MHz
4824
48.88
74
-25.12
Pk
Horizontal
4824
34.51
54
-19.49
AV
Horizontal
7236
52.98
74
-21.02
pk
Horizontal
7236
38.37
54
-15.63
AV
Horizontal
4824
43.81
74
-30.19
Pk
Vertical
4824
25.81
54
-28.19
AV
Vertical
7236
48.63
74
-25.37
Pk
Vertical
7236
33.44
54
-20.56
AV
Vertical
TX 11b 2437MHz
4874
47.87
74
-26.13
Pk
Horizontal
4874
41.64
54
-12.36
AV
Horizontal
7311
48.45
74
-25.55
Pk
Horizontal
7311
41.99
54
-12.01
AV
Horizontal
4874
48.97
74
-25.03
Pk
Vertical
4874
42.64
54
-11.36
AV
Vertical
7311
49.86
74
-24.14
Pk
Vertical
7311
41.97
54
-12.03
AV
Vertical
TX 11b 2462MHz
4924
48.88
74
-25.12
Pk
Horizontal
4924
41.85
54
-12.15
AV
Horizontal
7386
48.64
74
-25.36
Pk
Horizontal
7386
41.37
54
-12.63
AV
Horizontal
4924
47.79
74
-26.21
Pk
Vertical
4924
41.68
54
-12.32
AV
Vertical
7386
49.79
74
-24.21
Pk
Vertical
7386
41.45
54
-12.55
AV
Vertical
RESULT: PASS
Note:
1. Margin = Emission Leve - Limit
2.1GHz-25GHz(All test modes had been pre-tested. The 802.11b mode is the worst case and recorded
in the report. No recording in the test report at least have 20dB margin).
Report No.: AGC02399180201FE04
Page 38 of 42
12. BAND EDGE EMISSION
12.1. MEASUREMENT PROCEDURE
1)Radiated restricted band edge measurements
The radiated restricted band edge measurements are measured with an EMI test receiver connected to the
receive antenna while the EUT is transmitting
2)Conducted Emissions at the bang edge
a)The transmitter output was connected to the spectrum analyzer
b)Set RBW=100kHz,VBW=300kHz
c)Suitable frequency span including 100kHz bandwidth from band edge
12.2. TEST SET-UP
Radiated same as 11.2
Conducted set up
EUT
Spectrum analyzer
cable
Report No.: AGC02399180201FE04
Page 39 of 42
12.3. RADIATED TEST RESULT
Frequency
Emission Level
Limits
Margin
Detector
(MHz)
(dBμV/m)
(dBμV/m)
(dB)
Type
Comment
TX 11b 2412MHz
2399.9
48.89
74
-25.11
pk
Horizontal
2399.9
42.08
54
-11.92
AV
Horizontal
2400
49.28
74
-24.72
pk
Horizontal
2400
41.69
54
-12.31
AV
Horizontal
2399.9
47.81
74
-26.19
pk
Vertical
2399.9
41.07
54
-12.93
AV
Vertical
2400
49.09
74
-24.91
pk
Vertical
2400
41.20
54
-12.80
AV
Vertical
TX 11b 2462MHz
2483.5
49.41
74
-24.59
pk
Horizontal
2483.5
42.37
54
-11.63
AV
Horizontal
2483.6
47.53
74
-26.47
pk
Horizontal
2483.6
41.44
54
-12.56
AV
Horizontal
2483.5
47.52
74
-26.48
pk
Vertical
2483.5
42.61
54
-11.39
AV
Vertical
2483.6
48.39
74
-25.61
pk
Vertical
2483.6
40.13
54
-13.87
AV
Vertical
RESULT: PASS
Note: Scan with 11b,11g,11n, the worst case is 11b Mode
Margin= Emission Level -Limit.
Report No.: AGC02399180201FE04
Page 40 of 42
12.4. CONDUCTED TEST RESULT
Test Graph
11b-LCH
11b-HCH
11g-LCH
11g-HCH
11nHT20-LCH
11nHT20-HCH
Report No.: AGC02399180201FE04
Page 41 of 42
11nHT40-LCH
11nHT40-HCH
Report No.: AGC02399180201FE04
Page 42 of 42
APPENDIX A: PHOTOGRAPHS OF TEST SETUP
RADIATED EMISSION TEST SETUP
RADIATED EMISSION ABOVE 1G TEST SETUP
----END OF REPORT----
Download: MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Mirror Download [FCC.gov]MINI3 Tablet pc Test Report EMC COMPLIANCE CONEDERA S.A.
Document ID3839097
Application IDu0jq6aXVqdS8/frxtLG4gQ==
Document Description14_mini3 TestRpt DTS-WiFi p2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize474.96kB (5936953 bits)
Date Submitted2018-05-04 00:00:00
Date Available2018-05-04 00:00:00
Creation Date2018-05-03 11:26:08
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2018-05-03 11:28:38
Document TitleEMC COMPLIANCE TEST REPORT
Document CreatorMicrosoft® Office Word 2007
Document Author: Simon

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Modify Date                     : 2018:05:03 11:28:38+08:00
Create Date                     : 2018:05:03 11:26:08+08:00
Metadata Date                   : 2018:05:03 11:28:38+08:00
Creator Tool                    : Microsoft® Office Word 2007
Format                          : application/pdf
Title                           : EMC COMPLIANCE TEST REPORT
Creator                         : Simon
Document ID                     : uuid:5fdf9ad9-e650-4b91-9d26-40fbd4ff07bc
Instance ID                     : uuid:60154ef6-1468-4fb7-86a4-4397c2505a31
Producer                        : Microsoft® Office Word 2007
Page Count                      : 22
Author                          : Simon