DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.

SHENZHEN BMORN TECHNOLOGY CO.,LTD. 2in1 tablet pc

FCC ID Filing: 2ACPR-DTTAB-116-1

Page 1 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 2 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 3 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 4 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 5 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 6 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 7 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 8 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 9 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 10 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 11 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 12 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 13 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 14 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 15 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 16 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 17 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 18 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 19 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 20 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 21 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 22 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 23 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 24 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 25 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 26 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 27 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 28 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 29 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 30 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 31 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 32 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 33 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 34 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 35 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 36 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 37 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 38 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 39 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 40 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 41 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 42 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 43 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 44 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 45 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 46 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 47 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 48 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 49 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 50 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 51 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 52 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 53 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 54 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 55 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 56 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Page 57 of DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.

Report No.:NTEK-2017NT08075526F3
FCC RADIO TEST REPORT
FCC ID:2ACPR-DTTAB-116-1
Product: 2in1 tablet pc
Trade Mark: N/A
Model No.: DTTAB2in1-116-1
Serial Model: W1549
Report No.: NTEK-2017NT08075526F3
Issue Date: 21 Aug. 2017
Prepared for
SHENZHEN BMORN TECHNOLOGY CO.,LTD.
5/F, Hengfang Verteran Industrial Park, Xingye Road, Xixiang, Bao'an,
Shenzhen, Guangdong, China
Prepared by
Shenzhen NTEK Testing Technology Co., Ltd.
1/F, Building E, Fenda Science Park, Sanwei Community,
Xixiang Street Bao’an District, Shenzhen P.R. China
Tel.: +86-755-6115 9388
Fax.: +86-755-6115 6599
Website:http://www.ntek.org.cn
Version.1.3
Page 1 of 57
Report No.:NTEK-2017NT08075526F3
TABLE OF CONTENTS
TEST RESULT CERTIFICATION ...................................................................................................................... 3
SUMMARY OF TEST RESULTS ......................................................................................................................... 4
FACILITIES AND ACCREDITATIONS ............................................................................................................. 5
3.1 FACILITIES ........................................................................................................................................................... 5
3.2 LABORATORY ACCREDITATIONS AND LISTINGS ........................................................................................ 5
3.3
MEASUREMENT UNCERTAINTY ............................................................................................................... 5
GENERAL DESCRIPTION OF EUT .................................................................................................................. 6
DESCRIPTION OF TEST MODES ..................................................................................................................... 8
SETUP OF EQUIPMENT UNDER TEST ......................................................................................................... 10
6.1
6.2
6.3
BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM ..................................................................... 10
SUPPORT EQUIPMENT............................................................................................................................... 11
EQUIPMENTS LIST FOR ALL TEST ITEMS.............................................................................................. 12
TEST REQUIREMENTS .................................................................................................................................... 14
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
CONDUCTED EMISSIONS TEST ............................................................................................................... 14
RADIATED SPURIOUS EMISSION ............................................................................................................ 19
6DB BANDWIDTH....................................................................................................................................... 28
DUTY CYCLE ............................................................................................................................................... 32
MAXIMUM OUTPUT POWER .................................................................................................................... 34
POWER SPECTRAL DENSITY ................................................................................................................... 36
CONDUCTED BAND EDGE MEASUREMENT......................................................................................... 40
SPURIOUS RF CONDUCTED EMISSIONS................................................................................................ 44
ANTENNA APPLICATION .......................................................................................................................... 57
Version.1.3
Page 2 of 57
Report No.:NTEK-2017NT08075526F3
TEST RESULT CERTIFICATION
Applicant’s name ......................... : SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Address ....................................... : 5/F, Hengfang Verteran Industrial Park, Xingye Road, Xixiang,
Bao'an, Shenzhen, Guangdong, China
Manufacturer's Name .................. : SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Address ....................................... : 5/F, Hengfang Verteran Industrial Park, Xingye Road, Xixiang,
Bao'an, Shenzhen, Guangdong, China
Product description
Product name .............................. : 2in1 tablet pc
Model and/or type reference ..... : DTTAB2in1-116-1
Serial Model ................................ : W1549
Measurement Procedure Used:
APPLICABLE STANDARDS
APPLICABLE STANDARD/ TEST PROCEDURE
TEST RESULT
FCC 47 CFR Part 2, Subpart J
FCC 47 CFR Part 15, Subpart C
KDB 174176 D01 Line Conducted FAQ v01r01
Complied
ANSI C63.10-2013
FCC KDB 558074 D01 DTS Meas Guidance v04
This device described above has been tested by Shenzhen NTEK Testing Technology Co., Ltd., and the test
results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is
applicable only to the tested sample identified in the report.
This report shall not be reproduced except in full, without the written approval of Shenzhen NTEK Testing
Technology Co., Ltd., this document may be altered or revised by Shenzhen NTEK Testing Technology Co.,
Ltd., personnel only, and shall be noted in the revision of the document.
The test results of this report relate only to the tested sample identified in this report.
Date of Test
Testing Engineer
07 Aug. 2017 ~ 21 Aug. 2017
(Susan Su)
Technical Manager
(Jason Chen)
Authorized Signatory
(Sam Chen)
Version.1.3
Page 3 of 57
Report No.:NTEK-2017NT08075526F3
SUMMARY OF TEST RESULTS
FCC Part15 (15.247), Subpart C
Standard Section
Test Item
Verdict
15.207
Conducted Emission
PASS
15.247 (a)(2)
6dB Bandwidth
PASS
15.247 (b)
Maximum Output Power
PASS
15.247 (c)
Radiated Spurious Emission
PASS
15.247 (d)
Power Spectral Density
PASS
15.205
Band Edge Emission
PASS
15.203
Antenna Requirement
PASS
Remark
Remark:
1. “N/A” denotes test is not applicable in this Test Report.
2. All test items were verified and recorded according to the standards and without any deviation during
the test.
3. This EUT has also been tested and complied with the requirements of FCC Part 15, Subpart B,
recorded in a separate test report.
Version.1.3
Page 4 of 57
Report No.:NTEK-2017NT08075526F3
FACILITIES AND ACCREDITATIONS
3.1 FACILITIES
All measurement facilities used to collect the measurement data are located at
1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street Bao’an District, Shenzhen
518126 P.R. China
The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.10 and CISPR
Publication 22.
3.2 LABORATORY ACCREDITATIONS AND LISTINGS
Site Description
CNAS-Lab.
: The Laboratory has been assessed and proved to be in compliance with
CNAS-CL01:2006 (identical to ISO/IEC 17025:2005)
The Certificate Registration Number is L5516.
IC-Registration
The Certificate Registration Number is 9270A-1.
FCC- Accredited
Test Firm Registration Number: 463705.
Designation Number: CN1184
The Certificate Registration Number is 4298.01
This laboratory is accredited in accordance with the recognized
International Standard ISO/IEC 17025:2005 General requirements for
the competence of testing and calibration laboratories.
This accreditation demonstrates technical competence for a defined
scope and the operation of a laboratory quality management system
(refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009).
Shenzhen NTEK Testing Technology Co., Ltd.
1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang
Street, Bao’an District, Shenzhen 518126 P.R. China.
A2LA-Lab.
Name of Firm
Site Location
3.3 MEASUREMENT UNCERTAINTY
The reported uncertainty of measurement y±U, where expended uncertainty U is based on a standard
uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %.
No.
Item
Uncertainty
Conducted Emission Test
±1.38dB
RF power, conducted
±0.16dB
Spurious emissions, conducted
±0.21dB
All emissions, radiated(<1G)
±4.68dB
All emissions, radiated(>1G)
±4.89dB
Temperature
±0.5°C
Humidity
±2%
Version.1.3
Page 5 of 57
Report No.:NTEK-2017NT08075526F3
GENERAL DESCRIPTION OF EUT
Product Feature and Specification
Equipment
2in1 tablet pc
Trade Mark
N/A
FCC ID
2ACPR-DTTAB-116-1
Model No.
DTTAB2in1-116-1
Serial Model
W1549
Model Difference
All the model are the same circuit and RF module,
except the model No. and the colour.
Operating Frequency
2412-2462MHz for 802.11b/g/11n(HT20);
2422-2452MHz for 802.11n(HT40);
Modulation
DSSS with DBPSK/DQPSK/CCK for 802.11b;
OFDM with BPSK/QPSK/16QAM/64QAM for 802.11g/n;
Number of Channels
11 channels for 802.11b/g/11n(HT20);
7 channels for 802.11n(HT40);
Antenna Type
FPCB Antenna
Antenna Gain
2 dBi
DC supply:
DC 3.8V/8000mAh from Battery or DC 5V from Adapter.
Power supply
Adapter supply:
Model: BI18-050300-AdU
Input:AC 100~240V 50~60Hz 0.8A
Output:5V, 3A
HW Version
S101C REV:1.1
SW Version
WINDOS 10 HOME 64-bit
Note: Based on the application, features, or specification exhibited in User's Manual, the EUT is considered
as an ITE/Computing Device. More details of EUT technical specification, please refer to the User's Manual.
Version.1.3
Page 6 of 57
Report No.:NTEK-2017NT08075526F3
Revision History
Report No.
Version
Description
Issued Date
NTEK-2017NT08075526F3
Rev.01
Initial issue of report
Aug 21, 2017
Version.1.3
Page 7 of 57
Report No.:NTEK-2017NT08075526F3
DESCRIPTION OF TEST MODES
To investigate the maximum EMI emission characteristics generates from EUT, the test system was
pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode
which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration
mode(s) mentioned above was evaluated respectively.
The Transmitter was operated in the normal operating mode. The TX frequency was fixed which was for the
purpose of the measurements.
Test of channel included the lowest and middle and highest frequency to perform the test, then record on this
report.
Those data rates (802.11b: 1 Mbps; 802.11g: 6 Mbps; 802.11n (HT20): MCS0; 802.11n (HT40): MCS0) were
used for all test.
The EUT was pretested with 3 orientations placed on the table for the radiated emission measurement –X, Y,
and Z-plane. The Y-plane results were found as the worst case and were shown in this report.
Frequency and Channel list for 802.11b/g/n (HT20/HT40):
Channel
…
…
10
11
Note: fc=2412MHz+(k-1)×5MHz k=1 to 11
Frequency(MHz)
2412
2417
…
2432
2437
…
2457
2462
EUT built-in battery-powered, fully-charged battery use of the test battery
Version.1.3
Page 8 of 57
Report No.:NTEK-2017NT08075526F3
Test Mode:
Test Items
Mode
AC Power Line Conducted
Emissions
Normal Link
Maximum Conducted Output
Power
Power Spectral Density
6dB Spectrum Bandwidth
Radiated Emissions Below
1GHz
Radiated Emissions Above
1GHz
Band Edge Emissions
Version.1.3
Data Rate
Channel
Ant
11b/CCK
11g/BPSK
1 Mbps
6 Mbps
1/6/11
1/6/11
11n HT20
11n HT40
MCS0
MCS0
1/6/11
3/6/9
11b/CCK
11g/BPSK
11n HT20
11n HT40
1 Mbps
6 Mbps
MCS0
MCS0
1/6/11
1/6/11
1/6/11
3/6/9
11b/CCK
1 Mbps
1/6/11
11g/BPSK
11n HT20
11n HT40
Normal Link
6 Mbps
MCS0
MCS0
1/6/11
1/6/11
3/6/9
11b/CCK
1 Mbps
1/6/11
11g/BPSK
11n HT20
11n HT40
6 Mbps
MCS0
MCS0
1/6/11
1/6/11
3/6/9
11b/CCK
11g/BPSK
11n HT20
11n HT40
1 Mbps
6 Mbps
MCS0
MCS0
1/6/11
1/6/11
1/6/11
3/6/9
Page 9 of 57
Report No.:NTEK-2017NT08075526F3
SETUP OF EQUIPMENT UNDER TEST
6.1 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM
For AC Conducted Emission Mode
AC PLUG
E-1
EUT
C-1
E-2
Adapter
For Radiated Test Cases
EUT
For Conducted Test Cases
Measurement
Instrument
C2
EUT
Note:The temporary antenna connector is soldered on the PCB board in order to perform conducted tests and
this temporary antenna connector is listed in the equipment list.
Version.1.3
Page 10 of 57
Report No.:NTEK-2017NT08075526F3
6.2 SUPPORT EQUIPMENT
The EUT has been tested as an independent unit together with other necessary accessories or support units.
The following support units or accessories were used to form a representative test configuration during the
tests.
Item
Equipment
Mfr/Brand
Model/Type No.
FCC ID
Note
2ACPR-DTTAB-1
E-1.
2in1 tablet pc
N/A
DTTAB2in1-116-1
EUT
16-1
E-2
Adapter
N/A
BI18-050300-AdU
N/A
Item
Cable Type
Shielded Type
Ferrite Core
Length
C-1
Power Cable
NO
NO
1.2m
C-2
RF Cable
NO
NO
0.5m
Notes:
(1)
(2)
(3)
The support equipment was authorized by Declaration of Confirmation.
For detachable type I/O cable should be specified the length in cm in『Length』column.
“YES” is means “shielded” “with core”; “NO” is means “unshielded” “without core”.
Version.1.3
Page 11 of 57
Report No.:NTEK-2017NT08075526F3
6.3 EQUIPMENTS LIST FOR ALL TEST ITEMS
Radiation Test equipment
Kind of
Equipment
Item
Spectrum
Analyzer
Spectrum
Analyzer
EMI Test
Receiver
Last
calibration
Calibrated
until
Calibrati
on
period
E4407B
MY45108040 2017.06.06
2018.06.05
1 year
Agilent
N9020A
MY49100060 2016.11.10
2017.11.09
1 year
Agilent
N9038A
MY53227146 2017.06.06
2018.06.05 1 year
Manufacturer
Type No.
Agilent
Serial No.
Test Receiver
R&S
ESPI
101318
2017.06.06
2018.06.05
1 year
Bilog Antenna
TESEQ
CBL6111D
31216
2017.04.09
2018.04.08
1 year
50Ω Coaxial
Switch
Anritsu
MP59B
6200264416
2017.06.06
2018.06.05
1 year
Horn Antenna
EM
EM-AH-1018
2011071402
2017.04.09
2018.04.08
1 year
Horn Ant
Schwarzbeck
BBHA 9170
9170-181
2017.07.06
2018.07.05
1 year
Amplifier
EM
EM-30180
060538
2017.08.09
2018.08.08
1 year
10
Amplifier
MITEQ
TTA1840-35HG
177156
2017.06.06
2018.06.05
1 year
11
Loop Antenna
ARA
PLA-1030/B
1029
2017.06.06
2018.06.05
1 year
12
Power Meter
DARE
RPR3006W
100696
2017.08.07
2018.08.06
1 year
N/A
R-01
N/A
2017.04.21
2020.04.20
1 year
N/A
R-02
N/A
2017.04.21
2020.04.20
1 year
N/A
R-03
N/A
2017.04.21
2020.04.20
1 year
N/A
R-04
N/A
2017.04.21
2020.04.20
1 year
NTS
R001
N/A
N/A
N/A
N/A
13
14
15
16
17
Test Cable
(9KHz-30MHz)
Test Cable
(30MHz-1GHz)
High Test
Cable(1G-40G
Hz)
High Test
Cable(1G-40G
Hz)
temporary
antenna
connector
(Note)
Note:
We will use the temporary antenna connector (soldered on the PCB board) When conducted test
And this temporary antenna connector is listed within the instrument list
Version.1.3
Page 12 of 57
Report No.:NTEK-2017NT08075526F3
Conduction Test equipment
Kind of
Item
Manufacturer
Equipment
Type No.
Serial No.
Last
calibration
Calibrated
until
Calibration
period
Test Receiver
R&S
ESCI
101160
2017.06.06
2018.06.05
1 year
LISN
R&S
ENV216
101313
2017.04.19
2018.04.18
1 year
LISN
EMCO
3816/2
00042990
2017.06.06
2018.06.05
1 year
Anritsu
MP59B
6200264417
2017.06.06
2018.06.05
1 year
N/A
C01
N/A
2017.04.21
2020.04.20
1 year
N/A
C02
N/A
2017.04.21
2020.04.20
1 year
N/A
C03
N/A
2017.04.21
2020.04.20
1 year
29
2017.04.19
50Ω Coaxial
Switch
Test Cable
(9KHz-30MH
z)
Test Cable
(9KHz-30MH
z)
Test Cable
(9KHz-30MH
z)
Filter
TRILTHIC
2400MHz
2018.04.18
1 year
Note: Each piece of equipment is scheduled for calibration once a year.
Version.1.3
Page 13 of 57
Report No.:NTEK-2017NT08075526F3
TEST REQUIREMENTS
7.1 CONDUCTED EMISSIONS TEST
7.1.1
Applicable Standard
According to FCC Part 15.207(a) and KDB 174176 D01 Line Conducted FAQ v01r01
7.1.2
Conformance Limit
Conducted Emission Limit
Quasi-peak
Average
0.15-0.5
66-56*
56-46*
0.5-5.0
56
46
5.0-30.0
60
50
Note: 1. *Decreases with the logarithm of the frequency
2. The lower limit shall apply at the transition frequencies
3. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz.
Frequency(MHz)
7.1.3
Measuring Instruments
The Measuring equipment is listed in the section 6.3 of this test report.
7.1.4
Test Configuration
Reference
Ground
EMI Receiver
80cm
LISN
7.1.5
EUT
Auxiliary
Equipment
80cm
Reference
Ground
50Ω
LISN
Test Procedure
According to the requirements in Section 13.1.4.1 of ANSI C63.10-2013 Conducted emissions the EUT
measured in the frequency range between 0.15 MHz and 30 MHz using CISPR Quasi-Peak and average
detector mode.
1. The EUT was placed 0.4 meter from the conducting wall of the shielding room.
2. The EUT was placed on a table which is 0.8m above ground plane.
3. Connect EUT to the power mains through a line impedance stabilization network (LISN). All other
support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling
impedance for the measuring instrument.
4. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in
the center forming a bundle 30 to 40cm long.
5. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable
may be terminated, if required, using the correct terminating impedance. The overall length shall not
exceed 1 m.
6. LISN at least 80 cm from nearest part of EUT chassis.
7. The frequency range from 150KHz to 30MHz was searched.
8. Set the test-receiver system to Peak Detect Function and specified bandwidth(IF bandwidth=9KHz) with
Maximum Hold Mode
9. For the actual test configuration, please refer to the related Item –EUT Test Photos.
Version.1.3
Page 14 of 57
Report No.:NTEK-2017NT08075526F3
7.1.6
Test Results
EUT:
2in1 tablet pc
Temperature:
Pressure:
26 ℃
Test Voltage :
DC 5V from Adapter AC 120V/60Hz
Frequency
DTTAB2in1-116
-1
Relative Humidity:54%
Phase :
Test Mode:
Normal Link
Model Name :
1010hPa
Reading Level Correct Factor
Measure-ment
Limits
Margin
Remark
(MHz)
(dBμV)
(dB)
(dBμV)
(dBμV)
(dB)
0.1675
45.18
9.82
55.00
65.08
-10.08
QP
0.1675
27.07
9.82
36.89
55.08
-18.19
AVG
0.3659
33.97
9.83
43.80
58.59
-14.79
QP
0.3659
17.26
9.83
27.09
48.59
-21.50
AVG
0.5897
30.72
9.83
40.55
56.00
-15.45
QP
0.5897
12.93
9.83
22.76
46.00
-23.24
AVG
1.2540
29.32
9.90
39.22
56.00
-16.78
QP
1.2540
13.48
9.90
23.38
46.00
-22.62
AVG
2.4219
28.73
9.92
38.65
56.00
-17.35
QP
2.4219
16.01
9.92
25.93
46.00
-20.07
AVG
5.1539
29.53
10.05
39.58
60.00
-20.42
QP
5.1539
16.26
10.05
26.31
50.00
-23.69
AVG
Remark:
1. All readings are Quasi-Peak and Average values.
2. Factor = Insertion Loss + Cable Loss.
Version.1.3
Page 15 of 57
Report No.:NTEK-2017NT08075526F3
EUT:
2in1 tablet pc
Temperature:
Pressure:
Test Voltage :
26 ℃
Frequency
DTTAB2in1-1161
Relative Humidity: 54%
Phase :
Test Mode:
Normal Link
Model Name :
1010hPa
DC 5V from Adapter AC 120V/60Hz
Reading Level Correct Factor
Measure-ment
Limits
Margin
Remark
(MHz)
(dBμV)
(dB)
(dBμV)
(dBμV)
(dB)
0.1980
41.79
9.92
51.71
63.69
-11.98
QP
0.1980
11.44
9.92
21.36
53.69
-32.33
AVG
0.3458
35.24
9.92
45.16
59.06
-13.90
QP
0.3458
18.84
9.92
28.76
49.06
-20.30
AVG
0.7860
29.60
9.93
39.53
56.00
-16.47
QP
0.7860
14.37
9.93
24.30
46.00
-21.70
AVG
1.3500
30.86
9.93
40.79
56.00
-15.21
QP
1.3500
15.09
9.93
25.02
46.00
-20.98
AVG
2.7540
29.75
9.95
39.70
56.00
-16.30
QP
2.7540
17.68
9.95
27.63
46.00
-18.37
AVG
5.4537
26.92
9.98
36.90
60.00
-23.10
QP
5.4537
15.41
9.98
25.39
50.00
-24.61
AVG
Remark:
1. All readings are Quasi-Peak and Average values.
2. Factor = Insertion Loss + Cable Loss.
Version.1.3
Page 16 of 57
Report No.:NTEK-2017NT08075526F3
EUT:
2in1 tablet pc
Temperature:
26 ℃
Pressure:
Test Voltage :
1010hPa
Frequency
DTTAB2in1-116
-1
Relative Humidity: 54%
Phase :
Test Mode:
Normal Link
Model Name :
DC 5V from Adapter AC 240V/60Hz
Reading Level Correct Factor
Measure-ment
Limits
Margin
Remark
(MHz)
(dBμV)
(dB)
(dBμV)
(dBμV)
(dB)
0.1819
41.88
9.82
51.70
64.39
-12.69
QP
0.1819
23.06
9.82
32.88
54.39
-21.51
AVG
0.3659
33.97
9.83
43.80
58.59
-14.79
QP
0.3659
16.40
9.83
26.23
48.59
-22.36
AVG
0.5655
32.27
9.83
42.10
56.00
-13.90
QP
0.5655
21.91
9.83
31.74
46.00
-14.26
AVG
0.9220
30.00
9.90
39.90
56.00
-16.10
QP
0.9220
10.55
9.90
20.45
46.00
-25.55
AVG
2.1299
29.50
9.87
39.37
56.00
-16.63
QP
2.1299
12.13
9.87
22.00
46.00
-24.00
AVG
6.5339
29.98
9.99
39.97
60.00
-20.03
QP
6.5339
18.02
9.99
28.01
50.00
-21.99
AVG
Remark:
1. All readings are Quasi-Peak and Average values.
2. Factor = Insertion Loss + Cable Loss.
Version.1.3
Page 17 of 57
Report No.:NTEK-2017NT08075526F3
EUT:
2in1 tablet pc
Temperature:
Pressure:
Test Voltage :
26 ℃
Frequency
DTTAB2in1-116
-1
Relative Humidity: 54%
Phase :
Test Mode:
Normal Link
Model Name :
1010hPa
DC 5V from Adapter AC 240V/60Hz
Reading Level Correct Factor
Measure-ment
Limits
Margin
Remark
(MHz)
(dBμV)
(dB)
(dBμV)
(dBμV)
(dB)
0.1675
42.38
9.92
52.30
65.08
-12.78
QP
0.1675
13.39
9.92
23.31
55.08
-31.77
AVG
0.2548
37.46
9.92
47.38
61.60
-14.22
QP
0.2548
15.83
9.92
25.75
51.60
-25.85
AVG
0.6820
30.87
9.93
40.80
56.00
-15.20
QP
0.6820
15.88
9.93
25.81
46.00
-20.19
AVG
1.8140
33.58
9.94
43.52
56.00
-12.48
QP
1.8140
21.27
9.94
31.21
46.00
-14.79
AVG
3.1059
32.65
9.95
42.60
56.00
-13.40
QP
3.1059
22.57
9.95
32.52
46.00
-13.48
AVG
15.6219
35.48
10.25
45.73
60.00
-14.27
QP
15.6219
23.50
10.25
33.75
50.00
-16.25
AVG
Remark:
1. All readings are Quasi-Peak and Average values.
2. Factor = Insertion Loss + Cable Loss.
Version.1.3
Page 18 of 57
Report No.:NTEK-2017NT08075526F3
7.2 RADIATED SPURIOUS EMISSION
7.2.1
Applicable Standard
According to FCC Part 15.247(d) and 15.209 and ANSI C63.10-2013
7.2.2
Conformance Limit
According to FCC Part 15.247(d): radiated emissions which fall in the restricted bands, as defined in
§15.205(a), must also comply with the radiated emission limits specified in §15.209(a) (see §15.205(c)).
According to FCC Part15.205, Restricted bands
MHz
MHz
MHz
GHz
0.090-0.110
16.42-16.423
399.9-410
4.5-5.15
10.495-0.505
16.69475-16.69525
608-614
5.35-5.46
2.1735-2.1905
16.80425-16.80475
960-1240
7.25-7.75
4.125-4.128
25.5-25.67
1300-1427
8.025-8.5
4.17725-4.17775
37.5-38.25
1435-1626.5
9.0-9.2
4.20725-4.20775
73-74.6
1645.5-1646.5
9.3-9.5
6.215-6.218
74.8-75.2
1660-1710
10.6-12.7
6.26775-6.26825
123-138
2200-2300
14.47-14.5
8.291-8.294
149.9-150.05
2310-2390
15.35-16.2
8.362-8.366
156.52475-156.52525
2483.5-2500
17.7-21.4
8.37625-8.38675
156.7-156.9
2690-2900
22.01-23.12
8.41425-8.41475
162.0125-167.17
3260-3267
23.6-24.0
12.29-12.293
167.72-173.2
3332-3339
31.2-31.8
12.51975-12.52025
240-285
3345.8-3358
36.43-36.5
12.57675-12.57725
322-335.4
3600-4400
(2)
13.36-13.41
20dBc in any 100 kHz bandwidth outside the operating frequency band. In case the emission fall within the
restricted band specified on 15.205(a), then the 15.209(a) limit in the table below has to be followed.
Restricted
Field Strength (μV/m)
Field Strength (dBμV/m) Measurement Distance
Frequency(MHz)
0.009~0.490
2400/F(KHz)
20 log (uV/m)
300
0.490~1.705
2400/F(KHz)
20 log (uV/m)
30
1.705~30.0
30
29.5
30
30-88
100
40
88-216
150
43.5
216-960
200
46
Above 960
500
54
Limits of Radiated Emission Measurement(Above 1000MHz)
Frequency(MHz)
Above 1000
Class B (dBuV/m) (at 3M)
PEAK
AVERAGE
74
54
Remark :1. Emission level in dBuV/m=20 log (uV/m)
2. Measurement was performed at an antenna to the closed point of EUT distance of meters.
3. Distance extrapolation factor =40log(Specific distance/ test distance)( dB);
Limit line=Specific limits(dBuV) + distance extrapolation factor.
7.2.3
Measuring Instruments
The Measuring equipment is listed in the section 6.3 of this test report.
Version.1.3
Page 19 of 57
Report No.:NTEK-2017NT08075526F3
7.2.4
Test Configuration
(a) For radiated emissions below 30MHz
Turntable
3m
EUT
0.8 m
Test
Receiver
1.0m
Ground Plane
Coaxial Cable
(b) For radiated emissions from 30MHz to 1000MHz
3m
Turntable
1m to 4m
EUT
Test
Receiver
0.8m
Ground Plane
Coaxial Cable
(c) For radiated emissions above 1000MHz
3m
4m
Turntable
EUT
1.5m
1.5m
Amplifie
Version.1.3
Test Receiver
Page 20 of 57
Report No.:NTEK-2017NT08075526F3
7.2.5
Test Procedure
The test site semi-anechoic chamber has met the requirement of NSA tolerance 4 dB according to the
standards: ANSI C63.10-2013. The test distance is 3m.The setup is according to the requirements in Section
13.1.4.1 of ANSI C63.10-2013 and CAN/CSA-CEI/IEC CISPR 22.
This test is required for any spurious emission that falls in a Restricted Band, as defined in Section 15.205.
It must be performed with the highest gain of each type of antenna proposed for use with the EUT.
Use the following spectrum analyzer settings:
Spectrum Parameter
Setting
Attenuation
Auto
Start Frequency
1000 MHz
Stop Frequency
10th carrier harmonic
RB / VB (emission in restricted band)
1 MHz / 1 MHz for Peak, 1 MHz / 10Hz for Average
Receiver Parameter
Attenuation
Start ~ Stop Frequency
Start ~ Stop Frequency
Start ~ Stop Frequency
Setting
Auto
9kHz~150kHz / RB 200Hz for QP
150kHz~30MHz / RB 9kHz for QP
30MHz~1000MHz / RB 120kHz for QP
a. The measuring distance of at 3 m shall be used for measurements at frequency up to 1GHz and
frequencies above 1GHz,
b. The EUT was placed on the top of a rotating table 0.8 m for below 1GHz and 1.5m for above 1GHz the
ground at a 3 meter. The table was rotated 360 degrees to determine the position of the highest
radiation.
c. The height of the equipment or of the substitution antenna shall be 0.8 m for below 1GHz and 1.5m for
above 1GHz; the height of the test antenna shall vary between 1 m to 4 m. Both horizontal and vertical
polarizations of the antenna are set to make the measurement.
d. For the radiated emission test above 1GHz:
Place the measurement antenna away from each area of the EUT determined to be a source of
emissions at the specified measurement distance, while keeping the measurement antenna aimed at
the source of emissions at each frequency of significant emissions, with polarization oriented for
maximum response. The measurement antenna may have to be higher or lower than the EUT,
depending on the radiation pattern of the emission and staying aimed at the emission source for
receiving the maximum signal. The final measurement antenna elevation shall be that which maximizes
the emissions. The measurement antenna elevation for maximum emissions shall be restricted to a
range of heights of from 1 m to 4 m above the ground or reference ground plane.
e. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode
pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi
Peak detector mode re-measured.
f. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the EUT
shall be deemed to meet QP Limits and then no additional QP Mode measurement performed.
g For the actual test configuration, please refer to the related Item –EUT Test Photos.
Note:
Both horizontal and vertical antenna polarities were tested
and performed pretest to three orthogonal axis. The worst case emissions were reported
During the radiated emission test, the Spectrum Analyzer was set with the following configurations:
For peak measurement:
Set RBW=100 kHz for f < 1 GHz; VBW≥RBW; Sweep = auto; Detector function = peak; Trace = max hold;
Set RBW = 1 MHz, VBW= 3MHz for f≥1 GHz
For average measurement:
VBW = 10 Hz, when duty cycle is no less than 98 percent.
VBW ≥ 1/T, when duty cycle is less than 98 percent where T is the minimum transmission duration over
which the transmitter is on and is transmitting at its maximum power control level for the tested mode of
operation.
Version.1.3
Page 21 of 57
Report No.:NTEK-2017NT08075526F3
Note: for the frequency ranges below 30 MHz, a narrower RBW is used for these ranges but the measured
value should add a RBW correction factor (RBWCF) where RBWCF [dB] =10*lg(100 [kHz]/narrower RBW
[kHz]). , the narrower RBW is 1 kHz and RBWCF is 20 dB for the frequency 9 kHz to 150 kHz, and the
narrower RBW is 10 kHz and RBWCF is 10 dB for the frequency 150 kHz to 30 MHz.
7.2.6
Test Results
 Spurious Emission below 30MHz (9KHz to 30MHz)
EUT:
2in1 tablet pc
Model No.:
Temperature:
20 ℃
Relative Humidity:
Test Mode:
802.11b/g/n(HT20, HT40)
Test By:
DTTAB2in1-116-1
48%
Susan Su
Ant.Pol.
Emission Level(dBuV/m)
Limit 3m(dBuV/m)
Over(dB)
Freq.
(MHz)
H/V
PK
AV
PK
AV
PK
AV
--------Note: the amplitude of spurious emission that is attenuated by more than 20dB below the permissible
limit has no need to be reported.
Distance extrapolation factor =20log(Specific distance/ test distance)( dB);
Limit line=Specific limits(dBuV) + distance extrapolation factor
Version.1.3
Page 22 of 57
Report No.:NTEK-2017NT08075526F3

Spurious Emission below 1GHz (30MHz to 1GHz)
All the modulation modes have been tested, and the worst result was report as below:
EUT:
Temperature:
2in1 tablet pc
20 ℃
Pressure:
Test Voltage :
1010hPa
DC 3.8V
Polar
(H/V)
Model Name :
DTTAB2in1-116-1
Relative Humidity: 48%
Test Mode:
Normal Link
Frequency
Meter
Reading
Factor
Emission
Level
Limits
Margin
(MHz)
(dBuV)
(dB)
(dBuV/m)
(dBuV/m)
(dB)
32.6340
15.12
20.04
35.16
40.00
43.8119
19.10
14.49
33.59
40.00
88.6524
19.74
11.76
31.50
43.50
116.9495
19.69
10.27
29.96
43.50
230.9068
16.74
12.06
28.80
46.00
399.0300
15.55
15.13
30.68
46.00
Remark:
Absolute Level= ReadingLevel+ Factor, Margin= Absolute Level - Limit
Version.1.3
-4.84
-6.41
-12.00
-13.54
-17.20
-15.32
Remark
QP
QP
QP
QP
QP
QP
Page 23 of 57
Report No.:NTEK-2017NT08075526F3
Polar
(H/V)
Frequency
Meter
Reading
Factor
Emission
Level
Limits
Margin
(MHz)
(dBuV)
(dB)
(dBuV/m)
(dBuV/m)
(dB)
30.4237
6.48
21.02
27.50
40.00
56.0007
12.75
12.21
24.96
40.00
83.8156
15.16
11.24
26.40
40.00
120.6991
20.74
10.62
31.36
43.50
205.6750
18.15
13.80
31.95
43.50
417.6409
15.68
16.35
32.03
46.00
Remark:
Absolute Level= ReadingLevel+ Factor, Margin= Absolute Level - Limit
Version.1.3
-12.50
-15.04
-13.60
-12.14
-11.55
-13.97
Remark
QP
QP
QP
QP
QP
QP
Page 24 of 57
Report No.:NTEK-2017NT08075526F3
 Spurious Emission Above 1GHz (1GHz to 27GHz)
EUT:
2in1 tablet pc
Model No.:
DTTAB2in1-116-1
Temperature:
Relative Humidity:
48%
20 ℃
Test Mode:
802.11b/g/n(HT20, HT40)
Test By:
Susan Su
All the modulation modes have been tested, and the worst result was report as below:
Frequency
Read
Level
Cable
loss
Antenna
Factor
Preamp
Factor
Emission
Level
Limits
Margin
(MHz)
(dBμV)
(dB)
dB/m
(dB)
(dBμV/m)
(dBμV/m)
(dB)
Remark
Comment
Low Channel (2412 MHz)(802.11b)--Above 1G
4824.265
63.24
5.21
35.59
44.30
59.74
74.00
-14.26
Pk
Vertical
4824.265
40.48
5.21
35.59
44.30
36.98
54.00
-17.02
AV
Vertical
7236.296
60.28
6.48
36.27
44.60
58.43
74.00
-15.57
Pk
Vertical
7236.296
43.66
6.48
36.27
44.60
41.81
54.00
-12.19
AV
Vertical
4824.414
61.10
5.21
35.55
44.30
57.56
74.00
-16.44
Pk
Horizontal
4824.414
43.25
5.21
35.55
44.30
39.71
54.00
-14.29
AV
Horizontal
7236.428
63.09
6.48
36.27
44.52
61.32
74.00
-12.68
Pk
Horizontal
7236.428
46.96
6.48
-8.81
AV
Horizontal
4874.312
62.98
5.21
35.66
44.20
4874.312
43.21
5.21
35.66
7311.227
59.55
7.10
36.50
7311.227
47.40
7.10
4874.529
60.90
4874.529
48.75
7311.313
7311.313
36.27
44.52
45.19
54.00
Low Channel (2437 MHz)(802.11b)--Above 1G
59.65
74.00
-14.35
Pk
Vertical
44.20
39.88
54.00
-14.12
AV
Vertical
44.43
58.72
74.00
-15.28
Pk
Vertical
36.50
44.43
46.57
54.00
-7.43
AV
Vertical
5.21
35.66
44.20
57.57
74.00
-16.43
Pk
Horizontal
5.21
35.66
44.20
45.42
54.00
-8.58
AV
Horizontal
59.80
7.10
36.50
44.43
58.97
74.00
-15.03
Pk
Horizontal
42.19
7.10
-12.64
AV
Horizontal
4924.102
65.62
5.21
35.52
44.21
62.14
74.00
-11.86
Pk
Vertical
4924.102
42.35
5.21
35.52
44.21
38.87
54.00
-15.13
AV
Vertical
7386.425
60.47
7.10
36.53
44.60
59.50
74.00
-14.50
Pk
Vertical
7386.425
44.56
7.10
36.53
44.60
43.59
54.00
-10.41
AV
Vertical
4924.066
66.93
5.21
35.52
44.21
63.45
74.00
-10.55
Pk
Horizontal
4924.066
47.14
5.21
35.52
44.21
43.66
54.00
-10.34
AV
Horizontal
7386.198
60.94
7.10
36.53
44.60
59.97
74.00
-14.03
Pk
Horizontal
7386.198
45.23
7.10
36.53
44.60
44.26
54.00
-9.74
AV
Horizontal
36.50
44.43
41.36
54.00
Low Channel (2462 MHz)(802.11b)--Above 1G
Note: (1) All Readings are Peak Value (VBW=3MHz) and Peak Value (VBW=10Hz).
(2) Emission Level= Antenna Factor + Cable Loss + Read Level - Preamp Factor
(3) Data of measurement within this frequency range shown “ -- ” in the table above means the
reading of emissions are attenuated more than 20dB below the permissible limits or the field
strength is too small to be measured.
(4)”802.11b” mode is the worst mode. When PK value is lower than the Average value limit, average
don't record.
Version.1.3
Page 25 of 57
Report No.:NTEK-2017NT08075526F3
 Spurious Emission in Restricted Band 2310MHz -18000MHz
All the modulation modes have been tested, and the worst result was report as below:
(MHz)
Meter
Reading
(dBμV)
(dB)
Antenna
Factor
dB/m
2310.00
2310.00
2310.00
2310.00
2390.00
2390.00
2390.00
2390.00
2483.50
2483.50
2483.50
2483.50
58.39
44.02
58.65
41.99
57.95
42.00
56.85
41.42
57.54
42.72
58.99
41.29
2.97
2.97
2.97
2.97
3.14
3.14
3.14
3.14
3.58
3.58
3.58
3.58
27.80
27.80
27.80
27.80
27.21
27.21
27.21
27.21
27.70
27.70
27.70
27.70
2310.00
2310.00
2310.00
2310.00
2390.00
2390.00
2390.00
2390.00
2483.50
2483.50
2483.50
2483.50
59.17
44.22
56.49
42.93
57.38
42.03
57.99
43.44
58.58
44.22
59.20
42.09
2.97
2.97
2.97
2.97
3.14
3.14
3.14
3.14
3.58
3.58
3.58
3.58
27.80
27.80
27.80
27.80
27.21
27.21
27.21
27.21
27.70
27.70
27.70
27.70
2310.00
2310.00
2310.00
2310.00
2390.00
2390.00
2390.00
2390.00
2483.50
2483.50
2483.50
2483.50
58.25
43.69
58.77
42.57
58.15
41.92
56.82
42.50
57.79
42.82
58.55
42.65
2.97
2.97
2.97
2.97
3.14
3.14
3.14
3.14
3.58
3.58
3.58
3.58
27.80
27.80
27.80
27.80
27.21
27.21
27.21
27.21
27.70
27.70
27.70
27.70
2310.00
2310.00
2310.00
2310.00
2390.00
2390.00
2390.00
2390.00
2483.50
2483.50
2483.50
2483.50
59.61
44.45
57.34
42.97
58.07
41.91
57.95
44.02
58.36
44.68
58.47
42.51
2.97
2.97
2.97
2.97
3.14
3.14
3.14
3.14
3.58
3.58
3.58
3.58
27.80
27.80
27.80
27.80
27.21
27.21
27.21
27.21
27.70
27.70
27.70
27.70
Frequency
Version.1.3
Cable Loss
Preamp
Emission
Factor
Level
(dB)
(dBμV/m)
802.11b
43.80
45.36
43.80
30.99
43.80
45.62
43.80
28.96
43.80
44.50
43.80
28.55
43.80
43.40
43.80
27.97
44.00
44.82
44.00
30.00
44.00
46.27
44.00
28.57
802.11g
43.80
46.14
43.80
31.19
43.80
43.46
43.80
29.90
43.80
43.93
43.80
28.58
43.80
44.54
43.80
29.99
44.00
45.86
44.00
31.50
44.00
46.48
44.00
29.37
802.11n20
43.80
45.22
43.80
30.66
43.80
45.74
43.80
29.54
43.80
44.70
43.80
28.47
43.80
43.37
43.80
29.05
44.00
45.07
44.00
30.10
44.00
45.83
44.00
29.93
802.11n40
43.80
46.58
43.80
31.42
43.80
44.31
43.80
29.94
43.80
44.62
43.80
28.46
43.80
44.50
43.80
30.57
44.00
45.64
44.00
31.96
44.00
45.75
44.00
29.79
Limits
Margin
Detector
(dBμV/m)
(dB)
Type
74
54
74
54
74
54
74
54
74
54
74
54
-28.64
-23.01
-28.38
-25.04
-29.50
-25.45
-30.60
-26.03
-29.18
-24.00
-27.73
-25.43
Pk
AV
Pk
AV
Pk
AV
Pk
AV
Pk
AV
Pk
AV
Horizontal
Horizontal
Vertical
Vertical
Vertical
Vertical
Horizontal
Horizontal
Vertical
Vertical
Horizontal
Horizontal
74
54
74
54
74
54
74
54
74
54
74
54
-27.86
-22.81
-30.54
-24.10
-30.07
-25.42
-29.46
-24.01
-28.14
-22.50
-27.52
-24.63
Pk
AV
Pk
AV
Pk
AV
Pk
AV
Pk
AV
Pk
AV
Horizontal
Horizontal
Vertical
Vertical
Vertical
Vertical
Horizontal
Horizontal
Vertical
Vertical
Horizontal
Horizontal
74
54
74
54
74
54
74
54
74
54
74
54
-28.78
-23.34
-28.26
-24.46
-29.30
-25.53
-30.63
-24.95
-28.93
-23.90
-28.17
-24.07
Pk
AV
Pk
AV
Pk
AV
Pk
AV
Pk
AV
Pk
AV
Horizontal
Horizontal
Vertical
Vertical
Vertical
Vertical
Horizontal
Horizontal
Vertical
Vertical
Horizontal
Horizontal
74
54
74
54
74
54
74
54
74
54
74
54
-27.42
-22.58
-29.69
-24.06
-29.38
-25.54
-29.50
-23.43
-28.36
-22.04
-28.25
-24.21
Pk
AV
Pk
AV
Pk
AV
Pk
AV
Pk
AV
Pk
AV
Horizontal
Horizontal
Vertical
Vertical
Vertical
Vertical
Horizontal
Horizontal
Vertical
Vertical
Horizontal
Horizontal
Comment
Page 26 of 57
Report No.:NTEK-2017NT08075526F3
Spurious Emission in Restricted Bands 3260MMHz- 18000MHz
All the modulation modes have been tested, the worst result was report as below:
Frequenc Reading
Level
(MHz)
(dBμV)
Cable
Loss
(dB)
Antenna
Factor
dB/m
Preamp Emission
Limits
Margin
Factor
Level
(dB) (dBμV/m) (dBμV/m) (dB)
Detector
Comment
Type
3260
60.57
4.04
29.57
44.70
49.48
74
-24.52
Pk
Vertical
3260
55.77
4.04
29.57
44.70
44.68
54
-9.32
AV
Vertical
3260
61.80
4.04
29.57
44.70
50.71
74
-23.29
Pk
Horizontal
3260
56.89
4.04
29.57
44.70
45.80
54
-8.20
AV
Horizontal
3332
65.02
4.26
29.87
44.40
54.75
74
-19.25
Pk
Vertical
3332
54.00
4.26
29.87
44.40
43.73
54
-10.27
AV
Vertical
3332
62.92
4.26
29.87
44.40
52.65
74
-21.35
Pk
Horizontal
3332
53.01
4.26
29.87
44.40
42.74
54
-11.26
AV
Horizontal
17797
43.39
10.99
43.95
43.50
54.83
74
-19.17
Pk
Vertical
17797
33.33
10.99
43.95
43.50
44.77
54
-9.23
AV
Vertical
17788
44.13
11.81
43.69
44.60
55.03
74
-18.97
Pk
Horizontal
17788
31.92
11.81
43.69
44.60
42.82
54
-11.18
AV
Horizontal
“802.11b” mode is the worst mode. When PK value is lower than the Average value limit, average
don't record.
Version.1.3
Page 27 of 57
Report No.:NTEK-2017NT08075526F3
7.3 6DB BANDWIDTH
7.3.1
Applicable Standard
According to FCC Part 15.247(a)(2) and KDB 558074 DTS 01 Meas. Guidance v04
7.3.2
Conformance Limit
The minimum permissible 6dB bandwidth is 500 kHz.
7.3.3
Measuring Instruments
The Measuring equipment is listed in the section 6.3 of this test report.
7.3.4
Test Setup
Please refer to Section 6.1 of this test report.
7.3.5
Test Procedure
The testing follows KDB 558074 DTS 01 Meas. Guidance v04
The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator.
The path loss was compensated to the results for each measurement.
Set to the maximum power setting and enable the EUT transmit continuously.
The EUT was operating in controlled its channel.
Use the following spectrum analyzer settings:
Span = the frequency band of operation
RBW = 100KHz
VBW  3*RBW
Sweep = auto
Detector function = peak
Trace = max hold
Version.1.3
Page 28 of 57
Report No.:NTEK-2017NT08075526F3
7.3.6
Test Results
EUT:
2in1 tablet pc
Model No.:
DTTAB2in1-116-1
Temperature:
20 ℃
Relative Humidity:
48%
Test Mode:
802.11b/g/n20/n40
Test By:
Susan Su
Mode
802.11b
802.11g
802.11n20
802.11n40
Version.1.3
Channel
Low
Middle
High
Low
Middle
High
Low
Middle
High
Low
Middle
High
Frequency
(MHz)
6dB bandwidth
2412
2437
2462
2412
2437
2462
2412
2437
2462
2422
2437
2452
Result
(MHz)
Limit
(kHz)
10.10
10.10
10.09
16.60
16.59
16.61
17.85
17.85
17.84
36.51
36.50
36.48
≥500
≥500
≥500
≥500
≥500
≥500
≥500
≥500
≥500
≥500
≥500
≥500
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Page 29 of 57
Report No.:NTEK-2017NT08075526F3
Test plot
(802.11b) 6dB Bandwidth plot on channel 1
(802.11g) 6dB Bandwidth plot on channel 1
(802.11b) 6dB Bandwidth plot on channel 6
(802.11g) 6dB Bandwidth plot on channel 6
(802.11b) 6dB Bandwidth plot on channel 11
(802.11g) 6dB Bandwidth plot on channel 11
Version.1.3
Page 30 of 57
Report No.:NTEK-2017NT08075526F3
Test plot
(802.11n20) 6dB Bandwidth plot on channel 1
(802.11n40) 6dB Bandwidth plot on channel 3
(802.11n20) 6dB Bandwidth plot on channel 6
(802.11n40) 6dB Bandwidth plot on channel 6
(802.11n20) 6dB Bandwidth plot on channel 11
(802.11n40) 6dB Bandwidth plot on channel 9
Version.1.3
Page 31 of 57
Report No.:NTEK-2017NT08075526F3
7.4 DUTY CYCLE
7.4.1
Applicable Standard
According to KDB 558074)6)b), issued 06/09/2015.
7.4.2
Conformance Limit
No limit requirement.
7.4.3
Measuring Instruments
The Measuring equipment is listed in the section 6.3 of this test report.
7.4.4
Test Setup
Please refer to Section 6.1 of this test report.
7.4.5
Test Procedure
The zero-span mode on a spectrum analyzer or EMI receiver if the response time and spacing between bins
on the sweep are sufficient to permit accurate measurements of the on and off times of the transmitted signal.
Set the center frequency of the instrument to the center frequency of the transmission. Set RBW ≥ OBW if
possible; otherwise, set RBW to the largest available value. Set VBW ≥ RBW. Set detector = peak or
average. The zero-span measurement method shall not be used unless both RBW and VBW are > 50/T and
the number of sweep points across duration T exceeds 100. (For example, if VBW and/or RBW are limited to
3 MHz, then the zero-span method of measuring duty cycle shall not be used if T ≤ 16.7 microseconds.)
The transmitter output is connected to the Spectrum Analyzer. We tested accroding to the zero-span
measurement method, 6.0)b) in KDB 558074(issued 06/09/2015)
The largest availble value of RBW is 8 MHz and VBW is 50 MHz. The zero-span method of measuring duty
cycle shall not be used if T ≤ 6.25 microseconds. (50/6.25 = 8)
The zero-span method was used because all measured T data are > 6.25 microseconds and both RBW and
VBW are > 50/T.
The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator.
The path loss was compensated to the results for each measurement.
Set to the maximum power setting and enable the EUT transmit continuously.
The EUT was operating in controlled its channel.
Use the following spectrum analyzer settings:
Span = Zero Span
RBW = 8MHz(the largest available value)
VBW = 8MHz ( RBW)
Number of points in Sweep >100
Detector function = peak
Trace = Clear write
Measure Ttotal and Ton
Calculate Duty Cycle = Ton / Ttotal
Version.1.3
Page 32 of 57
Report No.:NTEK-2017NT08075526F3
7.4.6
Test Results
EUT:
2in1 tablet pc
Model No.:
DTTAB2in1-116-1
Temperature:
20 ℃
Relative Humidity:
48%
Test Mode:
802.11b/g/n20/n40
Test By:
Susan Su
Duty
Cycle
VBW
Ttotal
Duty Cycle
Mode
Channel
Ton
Factor
Setting
(dB)
802.11b
1Mbps
100%
10Hz
802.11g
6Mbps
100%
1KHz
802.11n HT20
MCS0
100%
1KHz
802.11n HT40
MCS0
100%
3KHz
Note: All the modulation modes were tested, the data of the worst mode are described in the following table.
Data
rate
Version.1.3
Page 33 of 57
Report No.:NTEK-2017NT08075526F3
7.5 MAXIMUM OUTPUT POWER
7.5.1
Applicable Standard
According to FCC Part 15.247(b)(3) and KDB 558074 DTS 01 Meas. Guidance v04
7.5.2
Conformance Limit
The maximum peak conducted output power of the intentional radiator for systems using digital modulation
in the 2400 - 2483.5 MHz bands shall not exceed: 1 Watt (30dBm). If transmitting antenna of directional gain
greater than 6dBi is used, the peak output power from the intentional radiator shall be reduced below the
above stated value by the amount in dB that the directional gain of the antenna exceeds 6 dBi. In case of
point-to-point operation, the limit has to be reduced by 1dB for every 3dB that the directional gain of the
antenna exceeds 6dBi.
7.5.3
Measuring Instruments
The following table is the setting of the power meter.
7.5.4
Test Setup
7.5.5
Test Procedure
1. Test procedures refer KDB 558074 D01 v03r05 section 9.2.3.2 Measurement using a power meter
(PM).
2. Alternatively, measurements may be performed using a wideband gated RF power meter provided that
the gate parameters are adjusted such that the power is measured only when the EUT is transmitting at its
maximum power control level. Since this measurement is made only during the ON time of the transmitter,
no duty cycle correction is required.
3. Multiple antenna system was performed in accordance with KDB 662911 D01 v02r01 Emissions
Testing of Transmitters with Multiple Outputs in the Same Band.
7.5.6
EUT opration during Test
The EUT was programmed to be in continuously transmitting mode.
Version.1.3
Page 34 of 57
Report No.:NTEK-2017NT08075526F3
7.5.7
Test Results
EUT:
2in1 tablet pc
Model No.:
DTTAB2in1-116-1
Temperature:
20 ℃
Relative Humidity:
48%
Test Mode:
802.11b/g/n20/n40
Test By:
Susan Su
Test Channel
Frequency
(MHz)
Power
Setting
11
2412
2437
2462
Default
Default
Default
11
2412
2437
2462
Default
Default
Default
11
2412
2437
2462
Default
Default
Default
2422
2437
2452
Default
Default
Default
Version.1.3
Duty Cycle
Average
Factor
Output Power
(dB)
(dBm)
802.11b
12.8
12.9
12.8
802.11g
9.5
9.6
9.3
802.11n HT20
9.6
9.6
9.4
802.11n HT40
8.7
8.6
8.7
Maximum
Output
Power(dBm)
LIMIT
(dBm)
Verdict
12.8
12.9
12.8
30
30
30
PASS
PASS
PASS
9.5
9.6
9.3
30
30
30
PASS
PASS
PASS
9.6
9.6
9.4
30
30
30
PASS
PASS
PASS
8.7
8.6
8.7
30
30
30
PASS
PASS
PASS
Page 35 of 57
Report No.:NTEK-2017NT08075526F3
7.6 POWER SPECTRAL DENSITY
7.6.1
Applicable Standard
According to FCC Part 15.247(e) and KDB 558074 DTS 01 Meas. Guidance v04
7.6.2
Conformance Limit
The transmitter power spectral density conducted from the transmitter to the antenna shall not be greater
than 8 dBm in any 3 kHz band during any time interval of continuous transmission.
7.6.3
Measuring Instruments
The Measuring equipment is listed in the section 6.3 of this test report.
7.6.4
Test Setup
Please refer to Section 6.1 of this test report.
7.6.5
Test Procedure
The testing follows Measurement Procedure 10.3 Method AVGPSD of FCC KDB Publication No. 558074
D01 DTS Meas. Guidance v04
This procedure may be used when the maximum (average) conducted output power was used to
demonstrate compliance to the output power limit. This is the baseline method for determining the maximum
(average) conducted PSD level. If the instrument has an RMS power averaging detector, it must be used;
otherwise, use the sample detector. The EUT must be configured to transmit continuously (duty cycle ≥
98%); otherwise sweep triggering/signal gating must be implemented to ensure that measurements are
made only when the EUT is transmitting at its maximum power control level (no transmitter off time is to be
considered).
The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator.
The path loss was compensated to the results for each measurement.
Set to the maximum power setting and enable the EUT transmit continuously.
The EUT was operating in controlled its channel.
a) Set instrument center frequency to DTS channel center frequency.
b) Set span to at least 1.5 times the OBW.
c) Set RBW to: 3 kHz ≤ RBW ≤ 100 kHz. .
d) Set VBW ≥3 x RBW.
e) Detector = power averaging (RMS) or sample detector (when RMS not available).
f) Ensure that the number of measurement points in the sweep ≥ 2 x span/RBW.
g) Sweep time = auto couple.
h) Employ trace averaging (RMS) mode over a minimum of 100 traces.
i) Use the peak marker function to determine the maximum amplitude level.
j) If measured value exceeds limit, reduce RBW (no less than 3 kHz) and repeat (note that this may require
zooming in on the emission of interest and reducin
Version.1.3
Page 36 of 57
Report No.:NTEK-2017NT08075526F3
7.6.6
Test Results
EUT:
2in1 tablet pc
Model No.:
DTTAB2in1-116-1
Temperature:
20 ℃
Relative Humidity:
48%
Test Mode:
802.11b/g/n20/n40
Test By:
Susan Su
Test Channel
Frequency
(MHz)
Duty Cycle
Factor(dB)
11
2412
2437
2462
11
2412
2437
2462
11
2412
2437
2462
2422
2437
2452
Version.1.3
Power Density
(dBm/3KHz)
802.11b
-19.127
-18.760
-18.083
802.11g
-21.260
-19.941
-19.989
802.11n HT20
-20.810
-20.417
-19.805
802.11n HT40
-23.916
-23.227
-23.484
Limit
(dBm/3KHz)
Verdict
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
Page 37 of 57
Report No.:NTEK-2017NT08075526F3
Test plot
(802.11b) PSD plot on channel 1
(802.11g) PSD plot on channel 1
(802.11b) PSD plot on channel 6
(802.11g) PSD plot on channel 6
(802.11b) PSD plot on channel 11
(802.11g) PSD plot on channel 11
Version.1.3
Page 38 of 57
Report No.:NTEK-2017NT08075526F3
Test plot
(802.11n20) PSD plot on channel 1
(802.11n40) PSD plot on channel 3
(802.11n20) PSD plot on channel 6
(802.11n40) PSD plot on channel 6
(802.11n20) PSD plot on channel 11
(802.11n40) PSD plot on channel 9
Version.1.3
Page 39 of 57
Report No.:NTEK-2017NT08075526F3
7.7 CONDUCTED BAND EDGE MEASUREMENT
7.7.1
Applicable Standard
According to FCC Part 15.247(d) and KDB 558074 DTS 01 Meas. Guidance v04
7.7.2
Conformance Limit
In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated
intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall
be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the
desired power, based on either an RF conducted or a radiated measurement, provided the transmitter
demonstrates compliance with the peak conducted power limits. If the transmitter complies with the
conducted power limits based on the use of RMS averaging over a time interval, as permitted under
paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20
dB.
7.7.3
Measuring Instruments
The Measuring equipment is listed in the section 6.3 of this test report.
7.7.4
Test Setup
Please refer to Section 6.1 of this test report.
7.7.5
Test Procedure
The testing follows FCC KDB Publication No. 558074 D01 DTS Meas. Guidance v04.
The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator.
The path loss was compensated to the results for each measurement.
Set to the maximum power setting and enable the EUT transmit continuously.
The EUT was operating in controlled its channel.
Set RBW to 100 kHz and VBW of spectrum analyzer to 300 kHz with a convenient frequency span including
100 kHz bandwidth from band edge.
Measure the highest amplitude appearing on spectral display and set it as a reference level. Plot the graph
with marking the highest point and edge frequency.
Repeat above procedures until all measured frequencies were complete.
Version.1.3
Page 40 of 57
Report No.:NTEK-2017NT08075526F3
7.7.6
Test Results
EUT:
2in1 tablet pc
Model No.:
DTTAB2in1-116-1
Temperature:
20 ℃
Relative Humidity:
48%
Test Mode:
802.11b/g/n20/n40
Test By:
Susan Su
Version.1.3
Page 41 of 57
Report No.:NTEK-2017NT08075526F3
Test plot For
802.11b: Band Edge-Low Channel
802.11g: Band Edge-Low Channel
802.11b: Band Edge-High Channel
802.11g: Band Edge-High Channel
Version.1.3
Page 42 of 57
Report No.:NTEK-2017NT08075526F3
Test plot For
802.11n20: Band Edge-Low Channel
802.11n40: Band Edge-Low Channel
802.11n20: Band Edge-High Channel
802.11n40: Band Edge-High Channel
Version.1.3
Page 43 of 57
Report No.:NTEK-2017NT08075526F3
7.8 SPURIOUS RF CONDUCTED EMISSIONS
7.8.1
Conformance Limit
1. Below -20dB of the highest emission level in operating band.
2. Fall in the restricted bands listed in section 15.205. The maximum permitted average field strength is
listed in section 15.209.
7.8.2
Measuring Instruments
The Measuring equipment is listed in the section 6.3 of this test report.
7.8.3
Test Setup
Please refer to Section 6.1 of this test report.
7.8.4
Test Procedure
The Spurious RF conducted emissions compliance of RF radiated emission should be measured by
following the guidance in ANSI C63.10-2013 with respect to maximizing the emission by rotating the EUT,
measuring the emission while the EUT is situated in three orthogonal planes (if appropriate), adjusting the
measurement antenna height and polarization etc. Set RBW=100kHz and VBW= 300KHz to measure the
peak field strength , and mwasure frequeny range from 9KHz to 26.5GHz.
7.8.5
Test Results
Remark: The measurement frequency range is from 9KHz to the 10th harmonic of the fundamental
frequency. The lowest, middle and highest channels are tested to verify the spurious emissions and bandege
measurement data.
Version.1.3
Page 44 of 57
Report No.:NTEK-2017NT08075526F3
Test Plot
Version.1.3
802.11b on channel 01
802.11b on channel 01
802.11b on channel 01
802.11b on channel 01
Page 45 of 57
Report No.:NTEK-2017NT08075526F3
Test Plot
Version.1.3
802.11b on channel 06
802.11b on channel 06
802.11b on channel 06
802.11b on channel 06
Page 46 of 57
Report No.:NTEK-2017NT08075526F3
Test Plot
Version.1.3
802.11b on channel 11
802.11b on channel 11
802.11b on channel 11
802.11b on channel 11
Page 47 of 57
Report No.:NTEK-2017NT08075526F3
Test Plot
Version.1.3
802.11g on channel 01
802.11g on channel 01
802.11g on channel 01
802.11g on channel 01
Page 48 of 57
Report No.:NTEK-2017NT08075526F3
Test Plot
Version.1.3
802.11g on channel 06
802.11g on channel 06
802.11g on channel 06
802.11g on channel 06
Page 49 of 57
Report No.:NTEK-2017NT08075526F3
Test Plot
Version.1.3
802.11g on channel 11
802.11g on channel 11
802.11g on channel 11
802.11g on channel 11
Page 50 of 57
Report No.:NTEK-2017NT08075526F3
Test Plot
Version.1.3
802.11n20 on channel 01
802.11n20 on channel 01
802.11 n20 on channel 01
802.11 n20 on channel 01
Page 51 of 57
Report No.:NTEK-2017NT08075526F3
Test Plot
Version.1.3
802.11 n20 on channel 06
802.11 n20 on channel 06
802.11 n20 on channel 06
802.11 n20 on channel 06
Page 52 of 57
Report No.:NTEK-2017NT08075526F3
Test Plot
Version.1.3
802.11 n20 on channel 11
802.11 n20 on channel 11
802.11 n20 on channel 11
802.11 n20 on channel 11
Page 53 of 57
Report No.:NTEK-2017NT08075526F3
Test Plot
Version.1.3
802.11n40 on channel 03
802.11n40 on channel 03
802.11n40 on channel 03
802.11n40 on channel 03
Page 54 of 57
Report No.:NTEK-2017NT08075526F3
Test Plot
Version.1.3
802.11n40 on channel 06
802.11 n40 on channel 06
802.11 n40 on channel 06
802.11 n40 on channel 06
Page 55 of 57
Report No.:NTEK-2017NT08075526F3
Test Plot
Version.1.3
802.11 n40 on channel 9
802.11 n40 on channel 9
802.11 n40 on channel 9
802.11 n40 on channel 9
Page 56 of 57
Report No.:NTEK-2017NT08075526F3
7.9 ANTENNA APPLICATION
7.9.1
Antenna Requirement
15.203 requirement: For intentional device, according to 15.203: an intentional radiator shall be designed to
ensure that no antenna other than that furnished by the responsible party shall be used with the device.
7.9.2
Result
The EUT antenna is permanent attached FPCB antenna (Gain:2dBi). It comply with the standard
requirement.
END OF REPORT
Version.1.3
Page 57 of 57
Download: DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Mirror Download [FCC.gov]DTTAB-116-1 2in1 tablet pc Test Report Wifi Report for FCC ID-V1.3 SHENZHEN BMORN TECHNOLOGY CO.,LTD.
Document ID3548622
Application ID2klNmqwGp2aC/6UHudXFew==
Document DescriptionTest Report Wi-Fi
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize235.5kB (2943799 bits)
Date Submitted2017-09-07 00:00:00
Date Available2017-09-07 00:00:00
Creation Date2017-08-31 09:22:03
Producing SoftwareAcrobat Distiller 15.0 (Windows)
Document Lastmod2017-08-31 09:22:03
Document TitleWifi Report for FCC ID-V1.3
Document CreatorPScript5.dll Version 5.2.2
Document Author: ntek136

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : ntek136
Create Date                     : 2017:08:31 09:22:03+08:00
Modify Date                     : 2017:08:31 09:22:03+08:00
XMP Toolkit                     : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15
Format                          : application/pdf
Title                           : Microsoft Word - Wifi Report for FCC ID-V1.3.doc
Creator                         : ntek136
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 15.0 (Windows)
Document ID                     : uuid:ddbaefd1-745a-48ac-b824-410a5d46c06a
Instance ID                     : uuid:c264aa89-912b-421b-b669-c9e70f690f67
Page Count                      : 57

Facebook Twitter Google+ RSS © FCCID.io 2018