K1A802MF Fingerprint Time Attendance Terminal RF Exposure Info EMC Test Hangzhou Hikvision Digital Technology Co., Ltd.

SGS-CSTC Standards Technical Services
(Shanghai) Co., Ltd.
588 West Jindu Road, Xinqiao, Songjiang, 201612 Shanghai, China
Telephone:
+86 (0) 21 6191 5666
Fax:
+86 (0) 21 6191 5678
ee.shanghai@sgs.com
Report No.: SHEM180400313203
Page:
1 of 8
Cover Page
MPE REPORT
Application No.:
SHEM1804003132CR
Applicant:
Hangzhou Hikvision Digital Technology Co., Ltd
FCC ID:
2ADTD-K1A802MF
Equipment Under Test (EUT):
NOTE: The following sample(s) was/were submitted and identified by the client as
Product Name:
Fingerprint Time Attendance Terminal
Model No.(EUT):
DS-K1A802MF
Add Model No.:
DS-K1A802MF-1, DS-K1A802MF-B, DS-K1A802MF-E, DS-K1A8503MF, DSK1A8503MF-B, DS-K1A802MFHGO, DS-K1A802MFOQU, DS-K1A802MFGPR,
DS-K1A802MFROG, DS-K1A802MFURG
Standards:
FCC Rules 47 CFR §2.1091
KDB447498 D01 General RF Exposure Guidance v06
Date of Receipt:
2018-04-26
Date of Test:
2018-05-04 to 2018-05-10
Date of Issue:
2018-05-21
Test Result:
Pass*
In the configuration tested, the EUT detailed in this report complied with the standards specified above.
Parlam Zhan
E&E Section Manager
The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this
report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure
the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS
International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by
SGS International Electrical Approvals in writing.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecu
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313203
Page:
2 of 8
Revision Record
Version
Description
Date
Remark
00
Original
2018-05-21
Authorized for issue
by:
Vincent Zhu /Project Engineer
Parlam Zhan /Reviewer
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_edocument.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that
information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole
responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction
documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test
report refer only to thesample(s) tested and such sample(s) are retained for 90 days only
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313203
Page:
3 of 8
Contents
Page
COVER PAGE ................................................................................................................................................. 1
CONTENTS ..................................................................................................................................................... 3
GENERAL INFORMATION ......................................................................................................................... 4
3.1
CLIENT INFORMATION.................................................................................................................................... 4
3.1
GENERAL DESCRIPTION OF E.U.T. ................................................................................................................. 4
3.2
TECHNICAL SPECIFICATIONS .......................................................................................................................... 4
3.3
TEST LOCATION ............................................................................................................................................. 5
3.4
TEST FACILITY ............................................................................................................................................... 5
TEST STANDARDS AND LIMITS ............................................................................................................... 6
4.1
FCC RADIOFREQUENCY RADIATION EXPOSURE LIMITS: ................................................................................. 6
MEASUREMENT AND CALCULATION ................................................................................................... 7
5.1
MAXIMUM TRANSMIT POWER ........................................................................................................................ 7
5.2
MPE CALCULATION....................................................................................................................................... 8
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at
www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this
document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s
instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction. documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any
unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of
the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313203
Page:
4 of 8
General Information
3.1 Client Information
Applicant:
Address of Applicant:
Hangzhou Hikvision Digital Technology Co., Ltd.
No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
Manufacturer:
Hangzhou Hikvision Digital Technology Co., Ltd.
Address of Manufacturer:
No. 555, Qianmo Road, Binjiang District,Hangzhou City,Zhejiang
Province,China
1. Hangzhou Hikvision Technology Co., Ltd.
2. Hangzhou Hikvision Electronics Co., Ltd.
3, Hangzhou Hikvision Digital Technology Co., Ltd.
1. No.700, Dongliu Road, Binjiang District, Hangzhou City, Zhejiang,
310052, China
2. No.299, Qiushi Road, Tonglu Economic Development Zone,
Tonglu County, Hangzhou, Zhejiang, 310052, China.
3, No. 555 Qianmo Road, Binjiang District, Hangzhou 310052, China
Factory:
Address of Factory:
3.1 General Description of E.U.T.
Test voltage:
DC 12V-1A by Adapter
Adapter:
Model: DSA-12PFT-12 FEU 120100
INPUT: 100~240V ~50/60Hz 0.5A
OUTPUT: +12V-1A
AC 120V 60Hz
Cable:
DC Cable 150cm for Adapter
Power supply:
3.2 Technical Specifications
2.4G WiFi
Antenna Gain
2dBi
Antenna Type
Connector Antenna
Channel Spacing
5MHz
802.11b: DSSS (CCK, DQPSK, DBPSK)
802.11g: OFDM (64QAM, 16QAM, QPSK, BPSK)
802.11n(HT20 and HT40): OFDM(64QAM, 16QAM, QPSK, BPSK)
802.11b/g/n(HT20):11
802.11n(HT40):7
802.11b/g/n(HT20): 2412MHz to 2462MHz
802.11n(HT40): 2422MHz to 2452MHz
Modulation Type
Number of Channels
Operation Frequency
13.56MHz
Operation Frequency:
13.56MHz
Modulation Type:
ASK
Antenna Type
Loop Antenna
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at
www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this
document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s
instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction. documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any
unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of
the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313203
Page:
5 of 8
3.3 Test Location
All tests were performed at:
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
588 West Jindu Road, Xinqiao, Songjiang, 201612 Shanghai, China
Tel: +86 21 6191 5666
Fax: +86 21 6191 5678
3.4 Test Facility
The test facility is recognized, certified, or accredited by the following organizations:
•
CNAS (No. CNAS L0599)
CNAS has accredited SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. to ISO/IEC
17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories
(CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for
the competence in the field of testing.
• NVLAP (Certificate No. 201034-0)
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. is accredited by the National
Voluntary Laboratory Accreditation Program(NVLAP). Certificate No. 201034-0.
• FCC –Designation Number: CN5033
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been recognized as an
accredited testing laboratory.
Designation Number: CN5033. Test Firm Registration Number: 479755.
•
Industry Canada (IC) – IC Assigned Code: 8617A
The 3m Semi-anechoic chamber of SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
has been registered by Certification and Engineering Bureau of Industry Canada for radio
equipment testing with Registration No.: 8617A-1.
•
VCCI (Member No.: 3061)
The 3m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services
(Shanghai) Co., Ltd. has been registered in accordance with the Regulations for Voluntary Control
Measures with Registration No.: R-3868,C-4336,T-12221,G-10830 respectively.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at
www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this
document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s
instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction. documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any
unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of
the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313203
Page:
6 of 8
Test Standards and Limits
4.1 FCC Radiofrequency radiation exposure limits:
According to§1.1310, the limit for general population/uncontrolled exposures
Frequency range
(MHz)
Electric field strength
(V/m)
Magnetic field strength
(A/m)
Power density
(mW/cm2)
Averaging time
(minutes)
Limits for General Population/Uncontrolled Exposure
0.3-1.34
614
1.63
*(100)
30
1.34-30
824/f
2.19/f
*(180/f2)
30
30-300
27.5
0.073
0.2
30
300-1500
f/1500
30
1500-100,000
1.0
30
Note:Limit for 13.56MHz is 60.77 V/m
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at
www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this
document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s
instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction. documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any
unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of
the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313203
Page:
7 of 8
Measurement and Calculation
5.1 Maximum transmit power
The Power Data is based on the RF Test Report SHEM180400313201 & SHEM180400313202
Power[mW]
Test Mode
Test Channel
Power[dBm]
11B
2412
15.25
33.50
11B
2437
15.13
32.58
11B
2462
14.92
31.05
11G
2412
12.32
17.06
11G
2437
12.40
17.38
11G
2462
11.87
15.38
11N20SISO
2412
11.95
15.67
11N20SISO
2437
11.52
14.19
11N20SISO
2462
11.49
14.09
11N40SISO
2422
11.82
15.21
11N40SISO
2437
12.02
15.92
11N40SISO
2452
11.68
14.72
13.56MHz: 52.79dBuV/m
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at
www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this
document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s
instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction. documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any
unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of
the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313203
Page:
8 of 8
5.2 MPE Calculation
The Max Conducted Average Output Power is 15.25dBm (33.50mW);
The best case gain of the antenna is 2dBi. 2dB logarithmic terms convert to numeric result is nearly
1.58
For FCC:
According to the formula S=
PG
, we can calculate S which is MPE.
4R 2
Note:
dBm
1) P (Watts) =Power Input to antenna = 10 10 / 1000
2) G (Antenna gain in numeric) = 10^ (Antenna gain in dBi /10)
3) R = distance to the center of radiation of antenna (in meter) = 20cm
4) MPE limit = 1mW/cm²
For WiFi: S=
33.50  1.58
PG
=0.011 mW/cm2
4  400  3.14
4R 
For 13.56MHz: 52.79dBuV/m=0.000436 V/m< 60.77 V/m.
13.56MHz and WiFi modules can simultaneous transmitting, so the maximum rate of MPE is
0.000436 0.011
=0.011<=1.0. according to the KDB447498 section 7.2 determine the device is

60.77
exclusion from SAR test.
--End of the Report--
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at
www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this
document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s
instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction. documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any
unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of
the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only