K1A802MF Fingerprint Time Attendance Terminal Test Report HD 271 S1 Hangzhou Hikvision Digital Technology Co., Ltd.
Hangzhou Hikvision Digital Technology Co., Ltd. Fingerprint Time Attendance Terminal
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. 588 West Jindu Road, Xinqiao, Songjiang, 201612 Shanghai, China Telephone: +86 (0) 21 6191 5666 Fax: +86 (0) 21 6191 5678 ee.shanghai@sgs.com Report No.: SHEM180400313201 Page: 1 of 58 TEST REPORT Application No.: FCC ID Applicant: Address of Applicant: Manufacturer: Address of Manufacturer: SHEM1804003132CR 2ADTD-K1A802MF Hangzhou Hikvision Digital Technology Co., Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China Hangzhou Hikvision Digital Technology Co., Ltd. No. 555, Qianmo Road, Binjiang District,Hangzhou City,Zhejiang Province,China Factory: 1. Hangzhou Hikvision Technology Co., Ltd. 2. Hangzhou Hikvision Electronics Co., Ltd. 3, Hangzhou Hikvision Digital Technology Co., Ltd. Address of Factory: 1. No.700, Dongliu Road, Binjiang District, Hangzhou City, Zhejiang, 310052, China 2. No.299, Qiushi Road, Tonglu Economic Development Zone, Tonglu County, Hangzhou, Zhejiang, 310052, China. 3, No. 555 Qianmo Road, Binjiang District, Hangzhou 310052, China Equipment Under Test (EUT): EUT Name: Fingerprint Time Attendance Terminal Model No.: DS-K1A802MF, DS-K1A802MF-1, DS-K1A802MF-B, DS-K1A802MF-E, DS-K1A8503MF, DS-K1A8503MF-B, DS-K1A802MFHGO, DSK1A802MFOQU, DS-K1A802MFGPR, DS-K1A802MFROG, DSK1A802MFURG ¤ ¤ Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. Trade mark: HIKVISION Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2018-04-26 Date of Test: 2018-05-04 to 2018-05-10 Date of Issue: 2018-05-21 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Parlam Zhan E&E Section Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 2 of 58 Revision Record Version Description Date Remark 00 Original 2018-05-15 Authorized for issue by: Vincent Zhu / Project Engineer Parlam Zhan /Reviewer This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 3 of 58 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(c) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Emissions at AC Power Line (150kHz-30MHz) 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.2 47 CFR Part 15, Subpart C 15.207 Pass Minimum 6dB Bandwidth 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.8.1 47 CFR Part 15, Subpart C 15.247a(2) Pass Conducted Peak Output Power 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.9.1 47 CFR Part 15, Subpart C 15.247(b)(3) Pass Power Spectrum Density 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.10.2 47 CFR Part 15, Subpart C 15.247(e) Pass Conducted Band Edges Measurement 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.13.3.2 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.11 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.209 & 15.247(d) Pass Radiated Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.10.4 47 CFR Part 15, Subpart C 15.209 & 15.247(d) Pass Declaration of EUT Family Grouping: Note: There are series models mentioned in this report, and they are the identical in electrical and electronic characters. Only the model DS-K1A802MF was tested since their differences were the software version, their naming and color silk. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 4 of 58 Contents Page COVER PAGE ............................................................................................................................................. 1 TEST SUMMARY ......................................................................................................................................... 3 CONTENTS .................................................................................................................................................. 4 GENERAL INFORMATION ......................................................................................................................... 6 4.1 4.2 4.3 4.4 4.5 4.6 4.7 DETAILS OF E.U.T. ................................................................................................................................ 6 DESCRIPTION OF SUPPORT UNITS........................................................................................................... 6 MEASUREMENT UNCERTAINTY ................................................................................................................ 7 TEST LOCATION ..................................................................................................................................... 8 TEST FACILITY ....................................................................................................................................... 8 DEVIATION FROM STANDARDS ................................................................................................................ 8 ABNORMALITIES FROM STANDARD CONDITIONS ....................................................................................... 8 EQUIPMENT LIST ....................................................................................................................................... 9 RADIO SPECTRUM TECHNICAL REQUIREMENT .................................................................................10 6.1 ANTENNA REQUIREMENT ......................................................................................................................10 6.1.1 Test Requirement: .........................................................................................................................10 6.1.2 Conclusion .....................................................................................................................................10 RADIO SPECTRUM MATTER TEST RESULTS ......................................................................................11 7.1 CONDUCTED EMISSIONS AT AC POWER LINE (150KHZ-30MHZ) ............................................................11 7.1.1 E.U.T. Operation ...........................................................................................................................11 7.1.2 Test Setup Diagram ......................................................................................................................11 7.1.3 Measurement Procedure and Data ..............................................................................................12 7.2 MINIMUM 6DB BANDWIDTH ...................................................................................................................15 7.2.1 E.U.T. Operation ...........................................................................................................................15 7.2.2 Test Setup Diagram ......................................................................................................................15 7.2.3 Measurement Procedure and Data ..............................................................................................15 7.3 CONDUCTED PEAK OUTPUT POWER .....................................................................................................16 7.3.1 E.U.T. Operation ...........................................................................................................................16 7.3.2 Test Setup Diagram ......................................................................................................................16 7.3.3 Measurement Procedure and Data ..............................................................................................16 7.4 POWER SPECTRUM DENSITY ................................................................................................................17 7.4.1 E.U.T. Operation ...........................................................................................................................17 7.4.2 Test Setup Diagram ......................................................................................................................17 7.4.3 Measurement Procedure and Data ..............................................................................................17 7.5 CONDUCTED BAND EDGES MEASUREMENT ...........................................................................................18 7.5.1 E.U.T. Operation ...........................................................................................................................18 7.5.2 Test Setup Diagram ......................................................................................................................18 7.5.3 Measurement Procedure and Data ..............................................................................................18 7.6 CONDUCTED SPURIOUS EMISSIONS ......................................................................................................19 7.6.1 E.U.T. Operation ...........................................................................................................................19 7.6.2 Test Setup Diagram ......................................................................................................................19 7.6.3 Measurement Procedure and Data ..............................................................................................19 7.7 RADIATED EMISSIONS WHICH FALL IN THE RESTRICTED BANDS................................................................20 7.7.1 E.U.T. Operation ...........................................................................................................................20 7.7.2 Test Setup Diagram ......................................................................................................................21 7.7.3 Measurement Procedure and Data ..............................................................................................22 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 5 of 58 7.8 RADIATED SPURIOUS EMISSIONS ..........................................................................................................49 7.8.1 E.U.T. Operation ...........................................................................................................................49 7.8.2 Test Setup Diagram ......................................................................................................................50 7.8.3 Measurement Procedure and Data ..............................................................................................51 TEST SETUP PHOTOGRAPHS ................................................................................................................58 EUT CONSTRUCTIONAL DETAILS .........................................................................................................58 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 6 of 58 General Information 4.1 Details of E.U.T. Power supply: Test voltage: Cable: Antenna Gain Antenna Type Channel Spacing Modulation Type Number of Channels Operation Frequency DC 12V-1A by Adapter Adapter: Model: DSA-12PFT-12 FEU 120100 INPUT: 100~240V ~50/60Hz 0.5A OUTPUT: +12V-1A AC 120V 60Hz DC Cable 150cm for Adapter 2 dBi Connector Antenna 5MHz 802.11b: DSSS (CCK, DQPSK, DBPSK) 802.11g: OFDM (64QAM, 16QAM, QPSK, BPSK) 802.11n(HT20 and HT40): OFDM(64QAM, 16QAM, QPSK, BPSK) 802.11b/g/n(HT20):11 802.11n(HT40):7 802.11b/g/n(HT20): 2412MHz to 2462MHz 802.11n(HT40): 2422MHz to 2452MHz 4.2 Description of Support Units Description Manufacturer Model No. Serial No. Laptop Lenovo ThinkPad X100e SecureCRT VanDyke V 6.2.0 Serial port adapter plate Test Plate 3 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 7 of 58 4.3 Measurement Uncertainty No. Item Measurement Uncertainty Radio Frequency 7.25 x 10-8 Timeout 2s Duty cycle 0.37% Occupied Bandwidth 3% RF conducted power 0.75dB RF power density 2.84dB Conducted Spurious emissions 0.75dB RF Radiated power 4.5dB (Below 1GHz) 4.8dB (Above 1GHz) 4.2dB (Below 30MHz) Radiated Spurious emission test 4.4dB (30MHz-1GHz) 4.6dB (1GHz-18GHz) 5.2dB (Above 18GHz) 10 Temperature test 1°C 11 Humidity test 3% 12 Supply voltages 1.5% 13 Time 3% Note: The measurement uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 8 of 58 4.4 Test Location All tests were performed at: SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. E&E Lab 588 West Jindu Road, Xinqiao, Songjiang, 201612 Shanghai, China Tel: +86 21 6191 5666 Fax: +86 21 6191 5678 No tests were sub-contracted. 4.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L0599) CNAS has accredited SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • NVLAP (Certificate No. 201034-0) SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. is accredited by the National Voluntary Laboratory Accreditation Program(NVLAP). Certificate No. 201034-0. • FCC –Designation Number: CN5033 SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been recognized as an accredited testing laboratory. Designation Number: CN5033. Test Firm Registration Number: 479755. • Industry Canada (IC) – IC Assigned Code: 8617A The 3m Semi-anechoic chamber of SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 8617A-1. • VCCI (Member No.: 3061) The 3m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: R-3868,C-4336,T-12221,G-10830 respectively. 4.6 Deviation from Standards None 4.7 Abnormalities from Standard Conditions None This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 9 of 58 Equipment List Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date Conducted Emission at AC Power Line EMI test receiver LISN R&S ESR7 SHEM162-1 2017-12-20 2018-12-19 Schwarzbeck NSLK8127 SHEM061-1 2017-12-20 2018-12-19 LISN EMCO 3816/2 SHEM019-1 2017-12-20 2018-12-19 Pulse limiter R&S ESH3-Z2 SHEM029-1 2017-12-20 2018-12-19 CE test Cable CE01 2017-12-26 2018-12-25 Conducted Test Spectrum Analyzer R&S FSP-30 SHEM002-1 2017-12-20 2018-12-19 Spectrum Analyzer Agilent N9020A SHEM181-1 2017-09-26 2018-09-25 Power meter R&S NRP SHEM057-1 2017-12-26 2018-12-25 Power Sensor R&S NRP-Z22 SHEM136-1 2017-07-22 2018-07-21 Power Sensor R&S NRP-Z91 SHEM057-2 2017-12-26 2018-12-25 Signal Generator R&S SMR40 SHEM058-1 2017-07-03 2018-07-02 Signal Generator Agilent N5182A SHEM182-1 2017-09-26 2018-09-25 Communication Tester R&S CMW270 SHEM183-1 2017-10-22 2018-10-21 Switcher Tonscend JS0806 SHEM184-1 2017-09-26 2018-09-25 Splitter Anritsu MA1612A SHEM185-1 Coupler e-meca 803-S-1 SHEM186-1 High-low Temp Cabinet Suzhou Zhihe TL-40 SHEM087-1 2017-09-26 2018-09-25 AC Power Stabilizer WOCEN 6100 SHEM045-1 2017-12-26 2018-12-25 DC Power Supply QJE QJ30003SII SHEM046-1 2017-12-26 2018-12-25 Conducted test Cable RF01, RF 02 2017-12-26 2018-12-25 Radiated Test EMI test receiver R&S Spectrum Analyzer ESU40 R&S Loop Antenna (9kHz-30MHz) Schwarzbeck SHEM051-1 2017-12-20 2018-12-19 FSP-30 SHEM002-1 2017-12-20 2018-12-19 FMZB1519 SHEM135-1 2017-04-10 2020-04-09 Antenna (25MHz-2GHz) Schwarzbeck VULB9168 SHEM048-1 2017-02-28 2020-02-27 Antenna (25MHz-3GHz) Schwarzbeck HL562 SHEM010-1 2017-02-28 2020-02-27 Horn Antenna (1-8GHz) Schwarzbeck HF906 SHEM009-1 2017-10-24 2020-10-23 Horn Antenna (1-18GHz) Schwarzbeck BBHA9120D SHEM050-1 2017-01-14 2020-01-13 Horn Antenna (14-40GHz) Schwarzbeck BBHA 9170 SHEM049-1 2017-12-03 2020-12-02 BDLNA-0001-412010 SHEM164-1 2017-08-22 2018-08-21 Pre-amplifier (9KHz-2GHz) CLAVIIO Pre-amplifier (1-18GHz) CLAVIIO BDLNA-0118-352810 SHEM050-2 2017-08-22 2018-08-21 High-amplifier (14-40GHz) Schwarzbeck 10001 SHEM049-2 2017-12-20 2018-12-19 Band filter LORCH 9BRX-875/X150-SR SHEM156-1 Band filter LORCH 13BRX-1950/X500-SR SHEM083-2 Band filter LORCH 5BRX-2400/X200-SR SHEM155-1 Band filter LORCH 5BRX-5500/X1000-SR SHEM157-2 High pass Filter Wainwright WHK3.0/18G-100SS SHEM157-1 Wainwright WHKS1700-3SS SHEM157-3 ST 11*6*6M SHEM078-2 2017-07-22 2020-07-21 2017-12-26 2018-12-25 High pass Filter Semi/Fully Anechoic RE test Cable RE01, RE02, RE06 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 10 of 58 Radio Spectrum Technical Requirement 6.1 Antenna Requirement 6.1.1 Test Requirement: 47 CFR Part 15, Subpart C 15.203 & 15.247(c) 6.1.2 Conclusion Standard Requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. 15.247(b) (4) requirement: The conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section, if transmitting antennas of directional gain greater than 6 dBi are used, the conducted output power from the intentional radiator shall be reduced below the stated values in paragraphs (b)(1), (b)(2), and (b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the antenna exceeds 6 dBi. EUT Antenna: The antenna is connector antenna and no consideration of replacement. The best case gain of the antenna is 2dBi. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 11 of 58 Radio Spectrum Matter Test Results 7.1 Conducted Emissions at AC Power Line (150kHz-30MHz) Test Requirement Test Method: Limit: Frequency of emission(MHz) 47 CFR Part 15, Subpart C 15.207 ANSI C63.10 (2013) Section 6.2 Conducted limit(dBμV) Quasi-peak Average 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 5-30 60 50 *Decreases with the logarithm of the frequency. 7.1.1 E.U.T. Operation Operating Environment: Temperature: 22 C Atmospheric Pressure: 1010 mbar Humidity: 50 % RH a:Charge + TX mode_Keep the EUT in charging and continuously transmitting Test mode mode with all modulation types. All data rates for each modulation type have been tested and found the data rate @ 1Mbps is the worst case of IEEE 802.11b; data rate @ 6Mbps is the worst case of IEEE 802.11g; data rate @ 6.5Mbps is the worst case of IEEE 802.11n(HT20); data rate @ 13.5Mbps is the worst case of IEEE 802.11n(HT40). Only the data of worst case is recorded in the report. 7.1.2 Test Setup Diagram This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 12 of 58 7.1.3 Measurement Procedure and Data 1) The mains terminal disturbance voltage test was conducted in a shielded room. 2) The EUT was connected to AC power source through a LISN 1 (Line Impedance Stabilization Network) which provides a 50ohm/50μH + 5ohm linear impedance. The power cables of all other units of the EUT were connected to a second LISN 2, which was bonded to the ground reference plane in the same way as the LISN 1 for the unit being measured. A multiple socket outlet strip was used to connect multiple power cables to a single LISN provided the rating of the LISN was not exceeded. 3) The tabletop EUT was placed upon a non-metallic table 0.8m above the ground reference plane. And for floor-standing arrangement, the EUT was placed on the horizontal ground reference plane, 4) The test was performed with a vertical ground reference plane. The rear of the EUT shall be 0.4 m from the vertical ground reference plane. The vertical ground reference plane was bonded to the horizontal ground reference plane. The LISN 1 was placed 0.8 m from the boundary of the unit under test and bonded to a ground reference plane for LISNs mounted on top of the ground reference plane. This distance was between the closest points of the LISN 1 and the EUT. All other units of the EUT and associated equipment was at least 0.8 m from the LISN 2. 5) In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.10 on conducted measurement. Remark: LISN=Read Level+ Cable Loss+ LISN Factor This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 13 of 58 Mode:a; Line:Live Line This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 14 of 58 Mode:a; Line:Neutral Line This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 15 of 58 7.2 Minimum 6dB Bandwidth Test Requirement Test Method: Limit: 47 CFR Part 15, Subpart C 15.247a(2) ANSI C63.10 (2013) Section 11.8.1 ≥500 kHz 7.2.1 E.U.T. Operation Operating Environment: Temperature: 21 C Atmospheric Pressure: 1010 mbar Humidity: 45 % RH a:Charge + TX mode_Keep the EUT in charging and continuously transmitting Test mode mode with all modulation types. All data rates for each modulation type have been tested and found the data rate @ 1Mbps is the worst case of IEEE 802.11b; data rate @ 6Mbps is the worst case of IEEE 802.11g; data rate @ 6.5Mbps is the worst case of IEEE 802.11n(HT20); data rate @ 13.5Mbps is the worst case of IEEE 802.11n(HT40). Only the data of worst case is recorded in the report. 7.2.2 Test Setup Diagram 7.2.3 Measurement Procedure and Data The detailed test data see: Appendix A for SHEM180400313201 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 16 of 58 7.3 Conducted Peak Output Power Test Requirement Test Method: Limit: 47 CFR Part 15, Subpart C 15.247(b)(3) ANSI C63.10 (2013) Section 11.9.1 Frequency range(MHz) Output power of the intentional radiator(watt) 1 for ≥50 hopping channels 902-928 0.25 for 25≤ hopping channels <50 1 for digital modulation 1 for ≥75 non-overlapping hopping channels 2400-2483.5 0.125 for all other frequency hopping systems 1 for digital modulation 5725-5850 1 for frequency hopping systems and digital modulation 7.3.1 E.U.T. Operation Operating Environment: Temperature: 21 C Atmospheric Pressure: 1010 mbar Humidity: 45 % RH a:Charge + TX mode_Keep the EUT in charging and continuously transmitting Test mode mode with all modulation types. All data rates for each modulation type have been tested and found the data rate @ 1Mbps is the worst case of IEEE 802.11b; data rate @ 6Mbps is the worst case of IEEE 802.11g; data rate @ 6.5Mbps is the worst case of IEEE 802.11n(HT20); data rate @ 13.5Mbps is the worst case of IEEE 802.11n(HT40). Only the data of worst case is recorded in the report. 7.3.2 Test Setup Diagram 7.3.3 Measurement Procedure and Data The detailed test data see: Appendix A for SHEM180400313201 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 17 of 58 7.4 Power Spectrum Density Test Requirement Test Method: Limit: 47 CFR Part 15, Subpart C 15.247(e) ANSI C63.10 (2013) Section 11.10.2 ≤8dBm in any 3 kHz band during any time interval of continuous transmission 7.4.1 E.U.T. Operation Operating Environment: Temperature: 21 C Atmospheric Pressure: 1010 mbar Humidity: 45 % RH a:Charge + TX mode_Keep the EUT in charging and continuously transmitting Test mode mode with all modulation types. All data rates for each modulation type have been tested and found the data rate @ 1Mbps is the worst case of IEEE 802.11b; data rate @ 6Mbps is the worst case of IEEE 802.11g; data rate @ 6.5Mbps is the worst case of IEEE 802.11n(HT20); data rate @ 13.5Mbps is the worst case of IEEE 802.11n(HT40). Only the data of worst case is recorded in the report. 7.4.2 Test Setup Diagram 7.4.3 Measurement Procedure and Data The detailed test data see: Appendix A for SHEM180400313201 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 18 of 58 7.5 Conducted Band Edges Measurement Test Requirement Test Method: Limit: 47 CFR Part 15, Subpart C 15.247(d) ANSI C63.10 (2013) Section 11.13.3.2 In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a) (see §15.205(c) 7.5.1 E.U.T. Operation Operating Environment: Temperature: 21 C Atmospheric Pressure: 1010 mbar Humidity: 45 % RH a:Charge + TX mode_Keep the EUT in charging and continuously transmitting Test mode mode with all modulation types. All data rates for each modulation type have been tested and found the data rate @ 1Mbps is the worst case of IEEE 802.11b; data rate @ 6Mbps is the worst case of IEEE 802.11g; data rate @ 6.5Mbps is the worst case of IEEE 802.11n(HT20); data rate @ 13.5Mbps is the worst case of IEEE 802.11n(HT40). Only the data of worst case is recorded in the report. 7.5.2 Test Setup Diagram 7.5.3 Measurement Procedure and Data The detailed test data see: Appendix A for SHEM180400313201 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 19 of 58 7.6 Conducted Spurious Emissions Test Requirement Test Method: Limit: 47 CFR Part 15, Subpart C 15.247(d) ANSI C63.10 (2013) Section 11.11 In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a) (see §15.205(c) 7.6.1 E.U.T. Operation Operating Environment: Temperature: 21 C 7.6.2 Test Setup Diagram Humidity: 45 % RH Atmospheric Pressure: 1010 mbar 7.6.3 Measurement Procedure and Data The detailed test data see: Appendix A for SHEM180400313201 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 20 of 58 7.7 Radiated Emissions which fall in the restricted bands Test Requirement Test Method: Limit: 47 CFR Part 15, Subpart C 15.209 & 15.247(d) ANSI C63.10 (2013) Section 6.10.5 Frequency(MHz) Field strength(microvolts/meter) Measurement distance(meters) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-88 100 88-216 150 216-960 200 Above 960 500 Remark: The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9-90kHz, 110-490kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. 7.7.1 E.U.T. Operation Operating Environment: Temperature: 21 C Atmospheric Pressure: 1010 mbar Humidity: 45 % RH a:Charge + TX mode_Keep the EUT in charging and continuously transmitting Test mode mode with all modulation types. All data rates for each modulation type have been tested and found the data rate @ 1Mbps is the worst case of IEEE 802.11b; data rate @ 6Mbps is the worst case of IEEE 802.11g; data rate @ 6.5Mbps is the worst case of IEEE 802.11n(HT20); data rate @ 13.5Mbps is the worst case of IEEE 802.11n(HT40). Only the data of worst case is recorded in the report. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 21 of 58 7.7.2 Test Setup Diagram This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 22 of 58 7.7.3 Measurement Procedure and Data a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 or 10 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter fully-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. c. The EUT was set 3 or 10 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. d. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. g. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. h. Test the EUT in the lowest channel, the middle channel, the Highest channel. i. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode, and found the X axis positioning which it is the worst case. j. Repeat above procedures until all frequencies measured was complete. Remark 1: Level= Read Level+ Cable Loss+ Antenna Factor- Preamp Factor Remark 2: For frequencies above 1GHz, the field strength limits are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. For the emissions whose peak level is lower than the average limit, only the peak measurement is shown in the report. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 23 of 58 Mode:a; Polarization:Horizontal; Modulation:b; bandwidth:20MHz; Channel:Low This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 24 of 58 Mode:a; Polarization:Vertical; Modulation:b; bandwidth:20MHz; Channel:Low This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 25 of 58 Mode:a; Polarization:Horizontal; Modulation:b; bandwidth:20MHz; Channel:High This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 26 of 58 Mode:a; Polarization:Vertical; Modulation:b; bandwidth:20MHz; Channel:High This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 27 of 58 Mode:a; Polarization:Horizontal; Modulation:g; bandwidth:20MHz; Channel:Low This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 28 of 58 Mode:a; Polarization:Horizontal; Modulation:g; bandwidth:20MHz; Channel:Low This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 29 of 58 Mode:a; Polarization:Vertical; Modulation:g; bandwidth:20MHz; Channel:Low This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 30 of 58 Mode:a; Polarization:Horizontal; Modulation:g; bandwidth:20MHz; Channel:High This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 31 of 58 Mode:a; Polarization:Horizontal; Modulation:g; bandwidth:20MHz; Channel:High This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 32 of 58 Mode:a; Polarization:Vertical; Modulation:g; bandwidth:20MHz; Channel:High This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 33 of 58 Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:20MHz; Channel:Low This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 34 of 58 Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:20MHz; Channel:Low This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 35 of 58 Mode:a; Polarization:Vertical; Modulation:n; bandwidth:20MHz; Channel:Low This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 36 of 58 Mode:a; Polarization:Vertical; Modulation:n; bandwidth:20MHz; Channel:Low This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 37 of 58 Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:20MHz; Channel:High This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 38 of 58 Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:20MHz; Channel:High This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 39 of 58 Mode:a; Polarization:Vertical; Modulation:n; bandwidth:20MHz; Channel:High This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 40 of 58 Mode:a; Polarization:Vertical; Modulation:n; bandwidth:20MHz; Channel:High This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 41 of 58 Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:40MHz; Channel:Low This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 42 of 58 Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:40MHz; Channel:Low This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 43 of 58 Mode:a; Polarization:Vertical; Modulation:n; bandwidth:40MHz; Channel:Low This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 44 of 58 Mode:a; Polarization:Vertical; Modulation:n; bandwidth:40MHz; Channel:Low This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 45 of 58 Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:40MHz; Channel:High This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 46 of 58 Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:40MHz; Channel:High This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 47 of 58 Mode:a; Polarization:Vertical; Modulation:n; bandwidth:40MHz; Channel:High This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 48 of 58 Mode:a; Polarization:Vertical; Modulation:n; bandwidth:40MHz; Channel:High This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 49 of 58 7.8 Radiated Spurious Emissions Test Requirement Test Method: Limit: 47 CFR Part 15, Subpart C 15.209 & 15.247(d) ANSI C63.10 (2013) Section 6.10.4 Frequency(MHz) Field strength(microvolts/meter) Measurement distance(meters) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-88 100 88-216 150 216-960 200 Above 960 500 Remark: The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9-90kHz, 110-490kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. 7.8.1 E.U.T. Operation Operating Environment: Temperature: 21 C Atmospheric Pressure: 1010 mbar Humidity: 45 % RH a:Charge + TX mode_Keep the EUT in charging and continuously transmitting Test mode mode with all modulation types. All data rates for each modulation type have been tested and found the data rate @ 1Mbps is the worst case of IEEE 802.11b; data rate @ 6Mbps is the worst case of IEEE 802.11g; data rate @ 6.5Mbps is the worst case of IEEE 802.11n(HT20); data rate @ 13.5Mbps is the worst case of IEEE 802.11n(HT40). Only the data of worst case is recorded in the report. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 50 of 58 7.8.2 Test Setup Diagram This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 51 of 58 7.8.3 Measurement Procedure and Data a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 or 10 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter fully-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. c. The EUT was set 3 or 10 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. d. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. g. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. h. Test the EUT in the lowest channel, the middle channel, the Highest channel. i. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode, and found the X axis positioning which it is the worst case. j. Repeat above procedures until all frequencies measured was complete. Remark: 1) For emission below 1GHz, through pre-scan found the worst case is the lowest channel. Only the worst case is recorded in the report. 2) The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic equation with a sample calculation is as follows: Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor 3) Scan from 9kHz to 25GHz, the disturbance above 18GHz and below 30MHz was very low. The points marked on above plots are the highest emissions could be found when testing, so only above points had been displayed. The amplitude of spurious emissions from the radiator which are attenuated more than 20dB below the limit need not be reported. 4) For frequencies above 1GHz, the field strength limits are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. For the emissions whose peak level is lower than the average limit, only the peak measurement is shown This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 52 of 58 Below 1GHz: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 53 of 58 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 54 of 58 Above 1GHz: Mode:a; Polarization:Horizontal; Modulation:b; bandwidth:20MHz; Channel:Low Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4824 7236 39.62 6.40 46.02 54 -7.98 peak 37.22 10.76 47.98 54 -6.02 peak 9648 35.13 14.37 49.50 54 -4.50 peak Mode:a; Polarization:Vertical; Modulation:b; bandwidth:20MHz; Channel:Low Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4824 43.58 6.40 49.98 54 -4.02 peak 7236 37.59 10.76 48.35 54 -5.65 peak 9648 31.50 14.37 45.87 54 -8.13 peak Mode:a; Polarization:Horizontal; Modulation:b; bandwidth:20MHz; Channel:middle Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4874 40.15 6.92 47.07 54 -6.93 peak 7311 34.08 11.08 45.16 54 -8.84 peak 9748 36.06 14.36 50.42 54 -3.58 peak Mode:a; Polarization:Vertical; Modulation:b; bandwidth:20MHz; Channel:middle Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4874 39.84 6.92 46.76 54 -7.24 peak 7311 36.33 11.08 47.41 54 -6.59 peak 9748 32.42 14.36 46.78 54 -7.22 peak Mode:a; Polarization:Horizontal; Modulation:b; bandwidth:20MHz; Channel:High Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4924 40.13 7.31 47.44 54 -6.56 peak 7386 38.90 11.41 50.31 54 -3.69 peak 9848 34.57 14.38 48.95 54 -5.05 peak Mode:a; Polarization:Vertical; Modulation:b; bandwidth:20MHz; Channel:High Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4924 39.46 7.31 46.77 54 -7.23 peak 7386 34.13 11.41 45.54 54 -8.46 peak 9848 32.57 14.38 46.95 54 -7.05 peak This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 55 of 58 Mode:a; Polarization:Horizontal; Modulation:g; bandwidth:20MHz; Channel:Low Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4824 40.21 6.40 46.61 54 -7.39 peak 7236 38.84 10.76 49.60 54 -4.40 peak 9648 34.40 14.37 48.77 54 -5.23 peak Mode:a; Polarization:Vertical; Modulation:g; bandwidth:20MHz; Channel:Low Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4824 40.22 6.40 46.62 54 -7.38 peak 7236 37.93 10.76 48.69 54 -5.31 peak 9648 32.92 14.37 47.29 54 -6.71 peak Mode:a; Polarization:Horizontal; Modulation:g; bandwidth:20MHz; Channel:middle Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4874 39.32 6.92 46.24 54 -7.76 peak 7311 35.39 11.08 46.47 54 -7.53 peak 9748 36.62 14.36 50.98 54 -3.02 peak Mode:a; Polarization:Vertical; Modulation:g; bandwidth:20MHz; Channel:middle Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4874 42.78 6.92 49.70 54 -4.30 peak 7311 39.95 11.08 51.03 54 -2.97 peak 9748 32.56 14.36 46.92 54 -7.08 peak Mode:a; Polarization:Horizontal; Modulation:g; bandwidth:20MHz; Channel:High Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4924 40.52 7.31 47.83 54 -6.17 peak 7386 37.65 11.41 49.06 54 -4.94 peak 9848 34.31 14.38 48.69 54 -5.31 peak Mode:a; Polarization:Vertical; Modulation:g; bandwidth:20MHz; Channel:High Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4924 43.17 7.31 50.48 54 -3.52 peak 7386 38.53 11.41 49.94 54 -4.06 peak 9848 33.16 14.38 47.54 54 -6.46 peak This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 56 of 58 Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:20MHz; Channel:Low Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4824 40.54 6.40 46.94 54 -7.06 peak 7236 36.51 10.76 47.27 54 -6.73 peak 9648 31.92 14.37 46.29 54 -7.71 peak Mode:a; Polarization:Vertical; Modulation:n; bandwidth:20MHz; Channel:Low Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4824 39.18 6.40 45.58 54 -8.42 peak 7236 36.54 10.76 47.30 54 -6.70 peak 9648 36.11 14.37 50.48 54 -3.52 peak Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:20MHz; Channel:middle Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4874 43.10 6.92 50.02 54 -3.98 peak 7311 34.69 11.08 45.77 54 -8.23 peak 9748 34.38 14.36 48.74 54 -5.26 peak Mode:a; Polarization:Vertical; Modulation:n; bandwidth:20MHz; Channel:middle Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4874 42.80 6.92 49.72 54 -4.28 peak 7311 38.85 11.08 49.93 54 -4.07 peak 9748 31.87 14.36 46.23 54 -7.77 peak Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:20MHz; Channel:High Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4924 40.43 7.31 47.74 54 -6.26 peak 7386 37.68 11.41 49.09 54 -4.91 peak 9848 31.45 14.38 45.83 54 -8.17 peak Mode:a; Polarization:Vertical; Modulation:n; bandwidth:20MHz; Channel:High Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4924 38.57 7.31 45.88 54 -8.12 peak 7386 34.80 11.41 46.21 54 -7.79 peak 9848 36.73 14.38 51.11 54 -2.89 peak This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 57 of 58 Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:40MHz; Channel:Low Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4844 40.19 6.60 46.79 54 -7.21 peak 7266 38.96 10.89 49.85 54 -4.15 peak 9688 32.48 14.35 46.83 54 -7.17 peak Mode:a; Polarization:Vertical; Modulation:n; bandwidth:40MHz; Channel:Low Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4844 42.56 6.60 49.16 54 -4.84 peak 7266 36.19 10.89 47.08 54 -6.92 peak 9688 31.72 14.35 46.07 54 -7.93 peak Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:40MHz; Channel:middle Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4874 41.01 6.92 47.93 54 -6.07 peak 7311 36.71 11.08 47.79 54 -6.21 peak 9748 36.38 14.36 50.74 54 -3.26 peak Mode:a; Polarization:Vertical; Modulation:n; bandwidth:40MHz; Channel:middle Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4874 38.94 6.92 45.86 54 -8.14 peak 7311 34.99 11.08 46.07 54 -7.93 peak 9748 36.21 14.36 50.57 54 -3.43 peak Mode:a; Polarization:Horizontal; Modulation:n; bandwidth:40MHz; Channel:High Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4904 42.25 7.22 49.47 54 -4.53 peak 7356 35.06 11.28 46.34 54 -7.66 peak 9808 33.03 14.37 47.40 54 -6.60 peak Mode:a; Polarization:Vertical; Modulation:n; bandwidth:40MHz; Channel:High Frequency RX_R Factor Emission Limit Margin Detector MHz dBuV dB dBuV/m dBuV/m dB 4904 40.20 7.22 47.42 54 -6.58 peak 7356 36.29 11.28 47.57 54 -6.43 peak 9808 31.64 14.37 46.01 54 -7.99 peak This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400313201 Page: 58 of 58 Test Setup Photographs Refer to the < Test Setup photos-FCC>. EUT Constructional Details Refer to the < External Photos > & < Internal Photos >. - End of the Report - This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
Source Exif Data [exif.tools]:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 58 Language : zh-CN Tagged PDF : Yes XMP Toolkit : 3.1-701 Producer : Microsoft® Word 2016 Title : HD 271 S1 Creator : LAB02 Creator Tool : Microsoft® Word 2016 Create Date : 2018:05:24 13:30:51+08:00 Modify Date : 2018:05:24 13:30:51+08:00 Document ID : uuid:037A2358-188E-4FA6-9BFA-DD45F5018352 Instance ID : uuid:037A2358-188E-4FA6-9BFA-DD45F5018352 Author : LAB02