K1A802MF Fingerprint Time Attendance Terminal Test Report Hangzhou Hikvision Digital Technology Co., Ltd.

Hangzhou Hikvision Digital Technology Co., Ltd. Fingerprint Time Attendance Terminal

Page 1 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 2 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 3 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 4 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 5 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 6 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 7 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 8 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 9 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 10 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 11 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 12 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 13 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 14 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 15 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 16 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 17 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 18 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 19 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 20 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 21 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 22 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Page 23 of K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.

SGS-CSTC Standards Technical Services
(Shanghai) Co., Ltd.
588 West Jindu Road, Xinqiao, Songjiang, 201612 Shanghai, China
Telephone:
+86 (0) 21 6191 5666
Fax:
+86 (0) 21 6191 5678
ee.shanghai@sgs.com
Report No.: SHEM180400313202
Page:
1 of 23
TEST REPORT
Application No.:
FCC ID
Applicant:
Address of Applicant:
Manufacturer:
Address of Manufacturer:
SHEM1804003132CR
2ADTD--K1A802MF
Hangzhou Hikvision Digital Technology Co., Ltd.
No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
Hangzhou Hikvision Digital Technology Co., Ltd.
No. 555, Qianmo Road, Binjiang District,Hangzhou City,Zhejiang
Province,China
Factory:
1. Hangzhou Hikvision Technology Co., Ltd.
2. Hangzhou Hikvision Electronics Co., Ltd.
3, Hangzhou Hikvision Digital Technology Co., Ltd.
Address of Factory:
1. No.700, Dongliu Road, Binjiang District, Hangzhou City, Zhejiang,
310052, China
2. No.299, Qiushi Road, Tonglu Economic Development Zone, Tonglu
County, Hangzhou, Zhejiang, 310052, China.
3, No. 555 Qianmo Road, Binjiang District, Hangzhou 310052, China
Equipment Under Test (EUT):
EUT Name:
Fingerprint Time Attendance Terminal
Model No.:
DS-K1A802MF, DS-K1A802MF-1, DS-K1A802MF-B, DS-K1A802MF-E,
DS-K1A8503MF, DS-K1A8503MF-B, DS-K1A802MFHGO, DSK1A802MFOQU, DS-K1A802MFGPR, DS-K1A802MFROG, DSK1A802MFURG ¤
¤
Please refer to section 2 of this report which indicates which model was
actually tested and which were electrically identical.
Trade mark:
HIKVISION
Standard(s) :
47 CFR Part 15, Subpart C 15.225
Date of Receipt:
2018-04-26
Date of Test:
2018-05-04 to 2018-05-10
Date of Issue:
2018-05-21
Pass*
Test Result:
* In the configuration tested, the EUT complied with the standards specified above.
Parlam Zhan
E&E Section Manager
The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report.
If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new
system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS
International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by
SGS International Electrical Approvals in writing.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
2 of 23
Revision Record
Version
Description
Date
Remark
00
Original
2018-05-21
Authorized for issue by:
Vincent Zhu / Project Engineer
Parlam Zhan /Reviewer
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
3 of 23
Test Summary
Radio Spectrum Technical Requirement
Item
Standard
Method
Requirement
Result
Antenna Requirement
47 CFR Part 15,
Subpart C 15.225
N/A
47 CFR Part 15,
Subpart C 15.203
Pass
Radio Spectrum Matter Part
Item
Standard
Method
Requirement
Result
Conducted Emissions
at AC Power Line
(150kHz-30MHz)
47 CFR Part 15,
Subpart C 15.225
ANSI C63.10 (2013)
Section 6.2
47 CFR Part 15,
Subpart C 15.207
Pass
Emission Mask
47 CFR Part 15,
Subpart C 15.225
ANSI C63.10 (2013)
Section 6.9.2
47 CFR Part 15,
Subpart C
Section
15.225(a)/(b)/(c)
PASS*
20dB Bandwidth
47 CFR Part 15,
Subpart C 15.225
ANSI C63.10 (2013)
Section 6.9
47 CFR Part 15,
Subpart C 15.215
Pass
Frequency tolerance
47 CFR Part 15,
Subpart C 15.225
ANSI C63.10 (2013)
Section 6.8
47 CFR Part 15,
Subpart C
15.225(e)
Pass
Radiated
Emissions(9kHz30MHz)
47 CFR Part 15,
Subpart C 15.225
ANSI C63.10 (2013)
Section 6.4&6.5
47 CFR Part 15,
Subpart C
15.225(d) &
15.209
Pass
Radiated
Emissions(30MHz1GHz)
47 CFR Part 15,
Subpart C 15.225
ANSI C63.10 (2013)
Section 6.4&6.5
47 CFR Part 15,
Subpart C
15.225(d) &
15.209
Pass
Remark: * The test level of the fundamental signal is below the limit of general spurious emission, so the test
no performs.
Declaration of EUT Family Grouping:
Note: There are series models mentioned in this report, and they are the identical in electrical and
electronic characters. Only the model DS-K1A802MF was tested since their differences were the
software version, their naming and color silk.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
4 of 23
Contents
Page
COVER PAGE ............................................................................................................................................. 1
TEST SUMMARY ......................................................................................................................................... 3
CONTENTS .................................................................................................................................................. 4
GENERAL INFORMATION ......................................................................................................................... 5
4.1
4.2
4.3
4.4
4.5
4.6
4.7
DETAILS OF E.U.T. ................................................................................................................................ 5
DESCRIPTION OF SUPPORT UNITS........................................................................................................... 5
MEASUREMENT UNCERTAINTY ................................................................................................................ 5
TEST LOCATION ..................................................................................................................................... 6
TEST FACILITY ....................................................................................................................................... 6
DEVIATION FROM STANDARDS ................................................................................................................ 6
ABNORMALITIES FROM STANDARD CONDITIONS ....................................................................................... 6
EQUIPMENT LIST ....................................................................................................................................... 7
RADIO SPECTRUM TECHNICAL REQUIREMENT ................................................................................... 8
6.1
ANTENNA REQUIREMENT ........................................................................................................................ 8
6.1.1 Test Requirement: ........................................................................................................................... 8
6.1.2 Conclusion ....................................................................................................................................... 8
RADIO SPECTRUM MATTER TEST RESULTS ........................................................................................ 9
7.1
CONDUCTED EMISSIONS AT AC POWER LINE (150KHZ-30MHZ) .............................................................. 9
7.1.1 E.U.T. Operation ............................................................................................................................. 9
7.1.2 Test Setup Diagram ........................................................................................................................ 9
7.1.3 Measurement Procedure and Data ..............................................................................................10
7.2
20DB BANDWIDTH................................................................................................................................13
7.2.1 E.U.T. Operation ...........................................................................................................................13
7.2.2 Test Setup Diagram ......................................................................................................................13
7.2.3 Measurement Procedure and Data ..............................................................................................13
7.3
FREQUENCY TOLERANCE ......................................................................................................................15
7.3.1 E.U.T. Operation ...........................................................................................................................15
7.3.2 Test Setup Diagram ......................................................................................................................15
7.3.3 Measurement Procedure and Data ..............................................................................................15
7.4
RADIATED EMISSIONS(9KHZ-30MHZ) ...................................................................................................17
7.4.1 E.U.T. Operation ...........................................................................................................................17
7.4.2 Test Setup Diagram ......................................................................................................................17
7.4.3 Measurement Procedure and Data ..............................................................................................18
7.5
RADIATED EMISSIONS(30MHZ-1GHZ) ..................................................................................................19
7.5.1 E.U.T. Operation ...........................................................................................................................19
7.5.2 Test Setup Diagram ......................................................................................................................19
7.5.3 Measurement Procedure and Data ..............................................................................................20
TEST SETUP PHOTOGRAPHS ................................................................................................................23
EUT CONSTRUCTIONAL DETAILS .........................................................................................................23
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
5 of 23
General Information
4.1 Details of E.U.T.
Power supply:
Test voltage:
Cable:
Antenna Type
Operation Frequency
Modulation Type
DC 12V-1A by Adapter
Adapter:
Model: DSA-12PFT-12 FEU 120100
INPUT: 100~240V ~50/60Hz 0.5A
OUTPUT: +12V-1A
AC 120V 60Hz
DC Cable 150cm for Adapter
Loop Antenna
13.56MHz
ASK
4.2 Description of Support Units
The EUT has been tested as an independent unit.
4.3 Measurement Uncertainty
No.
Item
Measurement Uncertainty
Radio Frequency
7.25 x 10-8
Timeout
2s
Duty cycle
0.37%
Occupied Bandwidth
3%
RF conducted power
0.75dB
RF power density
2.84dB
Conducted Spurious emissions
0.75dB
RF Radiated power
4.5dB (Below 1GHz)
4.8dB (Above 1GHz)
4.2dB (Below 30MHz)
Radiated Spurious emission test
4.4dB (30MHz-1GHz)
4.6dB (1GHz-18GHz)
5.2dB (Above 18GHz)
10
Temperature test
1°C
11
Humidity test
3%
12
Supply voltages
1.5%
13
Time
3%
Note: The measurement uncertainty represents an expanded uncertainty expressed at approximately the
95% confidence level using a coverage factor of k=2.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
6 of 23
4.4 Test Location
All tests were performed at:
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. E&E Lab
588 West Jindu Road, Xinqiao, Songjiang, 201612 Shanghai, China
Tel: +86 21 6191 5666
Fax: +86 21 6191 5678
No tests were sub-contracted.
4.5 Test Facility
The test facility is recognized, certified, or accredited by the following organizations:
• CNAS (No. CNAS L0599)
CNAS has accredited SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. to ISO/IEC
17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories
(CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories)
for the competence in the field of testing.
• NVLAP (Certificate No. 201034-0)
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. is accredited by the National
Voluntary Laboratory Accreditation Program(NVLAP). Certificate No. 201034-0.
• FCC –Designation Number: CN5033
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been recognized as an
accredited testing laboratory.
Designation Number: CN5033. Test Firm Registration Number: 479755.
• Industry Canada (IC) – IC Assigned Code: 8617A
The 3m Semi-anechoic chamber of SGS-CSTC Standards Technical Services (Shanghai) Co.,
Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio
equipment testing with Registration No.: 8617A-1.
• VCCI (Member No.: 3061)
The 3m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical
Services (Shanghai) Co., Ltd. has been registered in accordance with the Regulations for
Voluntary Control Measures with Registration No.: R-3868,C-4336,T-12221,G-10830 respectively.
4.6 Deviation from Standards
None
4.7 Abnormalities from Standard Conditions
None
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
7 of 23
Equipment List
Equipment
Manufacturer
Model No
Inventory No
Cal Date
Cal Due Date
SHEM162-1
2017-12-20
2018-12-19
Conducted Emission at AC Power Line
EMI test receiver
LISN
R&S
ESR7
Schwarzbeck
NSLK8127
SHEM061-1
2017-12-20
2018-12-19
LISN
EMCO
3816/2
SHEM019-1
2017-12-20
2018-12-19
Pulse limiter
R&S
ESH3-Z2
SHEM029-1
2017-12-20
2018-12-19
CE test Cable
CE01
2017-12-26
2018-12-25
SHEM002-1
2017-12-20
2018-12-19
Conducted Test
Spectrum Analyzer
R&S
FSP-30
Spectrum Analyzer
Agilent
N9020A
SHEM181-1
2017-09-26
2018-09-25
Power meter
R&S
NRP
SHEM057-1
2017-12-26
2018-12-25
Power Sensor
R&S
NRP-Z22
SHEM136-1
2017-07-22
2018-07-21
Power Sensor
R&S
NRP-Z91
SHEM057-2
2017-12-26
2018-12-25
Signal Generator
R&S
SMR40
SHEM058-1
2017-07-03
2018-07-02
Signal Generator
Agilent
N5182A
SHEM182-1
2017-09-26
2018-09-25
Communication Tester
R&S
CMW270
SHEM183-1
2017-10-22
2018-10-21
Switcher
Tonscend
JS0806
SHEM184-1
2017-09-26
2018-09-25
Splitter
Anritsu
MA1612A
SHEM185-1
Coupler
e-meca
803-S-1
SHEM186-1
High-low Temp Cabinet
Suzhou Zhihe
TL-40
SHEM087-1
2017-09-26
2018-09-25
AC Power Stabilizer
WOCEN
6100
SHEM045-1
2017-12-26
2018-12-25
DC Power Supply
QJE
QJ30003SII
SHEM046-1
2017-12-26
2018-12-25
Conducted test Cable
RF01, RF 02
2017-12-26
2018-12-25
SHEM051-1
2017-12-20
2018-12-19
Radiated Test
EMI test receiver
R&S
Spectrum Analyzer
ESU40
R&S
Loop Antenna (9kHz-30MHz) Schwarzbeck
FSP-30
SHEM002-1
2017-12-20
2018-12-19
FMZB1519
SHEM135-1
2017-04-10
2020-04-09
Antenna (25MHz-2GHz)
Schwarzbeck
VULB9168
SHEM048-1
2017-02-28
2020-02-27
Antenna (25MHz-3GHz)
Schwarzbeck
HL562
SHEM010-1
2017-02-28
2020-02-27
Horn Antenna (1-8GHz)
Schwarzbeck
HF906
SHEM009-1
2017-10-24
2020-10-23
Horn Antenna (1-18GHz)
Schwarzbeck
BBHA9120D
SHEM050-1
2017-01-14
2020-01-13
Horn Antenna (14-40GHz)
Schwarzbeck
BBHA 9170
SHEM049-1
2017-12-03
2020-12-02
BDLNA-0001-412010
SHEM164-1
2017-08-22
2018-08-21
Pre-amplifier (9KHz-2GHz) CLAVIIO
Pre-amplifier (1-18GHz)
CLAVIIO
BDLNA-0118-352810
SHEM050-2
2017-08-22
2018-08-21
High-amplifier (14-40GHz)
Schwarzbeck
10001
SHEM049-2
2017-12-20
2018-12-19
Band filter
LORCH
9BRX-875/X150-SR
SHEM156-1
Band filter
LORCH
13BRX-1950/X500-SR
SHEM083-2
Band filter
LORCH
5BRX-2400/X200-SR
SHEM155-1
Band filter
LORCH
5BRX-5500/X1000-SR
SHEM157-2
High pass Filter
Wainwright
WHK3.0/18G-100SS
SHEM157-1
High pass Filter
Semi/Fully Anechoic
RE test Cable
Wainwright
WHKS1700-3SS
SHEM157-3
ST
11*6*6M
SHEM078-2
2017-07-22
2020-07-21
2017-12-26
2018-12-25
RE01, RE02, RE06
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
8 of 23
Radio Spectrum Technical Requirement
6.1 Antenna Requirement
6.1.1 Test Requirement:
47 CFR Part 15, Subpart C 15.203
6.1.2 Conclusion
Standard Requirement:
An intentional radiator shall be designed to ensure that no antenna other than that furnished by the
responsible party shall be used with the device. The use of a antenna that uses a unique coupling to
the intentional radiator, the manufacturer may design the unit permanently attached antenna or of an
so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or
electrical connector is prohibited.
EUT Antenna:
The antenna is loop antenna and no consideration of replacement. The best case gain of the antenna
is 0dBi.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
9 of 23
Radio Spectrum Matter Test Results
7.1 Conducted Emissions at AC Power Line (150kHz-30MHz)
Test Requirement
Test Method:
Limit:
Frequency range (MHz)
47 CFR Part 15, Subpart C 15.207
ANSI C63.10 (2013) Section 6.2
Limit (dBuV)
Quasi-peak
Average
0.15-0.5
66 to 56*
56 to 46*
0.5-5
56
46
60
50
5-30
* Decreases with the logarithm of the frequency.
7.1.1 E.U.T. Operation
Operating Environment:
Atmospheric Pressure: 1010 mbar
Temperature:
22 °C
Humidity: 50 % RH
b:Charge + TX mode_Keep the EUT in charging and transmitting with modulation
Test mode
mode.
7.1.2 Test Setup Diagram
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
10 of 23
7.1.3 Measurement Procedure and Data
1) The mains terminal disturbance voltage test was conducted in a shielded room.
2) The EUT was connected to AC power source through a LISN 1 (Line Impedance Stabilization
Network) which provides a 50ohm/50µH + 5ohm linear impedance. The power cables of all other
units of the EUT were connected to a second LISN 2, which was bonded to the ground reference
plane in the same way as the LISN 1 for the unit being measured. A multiple socket outlet strip was
used to connect multiple power cables to a single LISN provided the rating of the LISN was not
exceeded.
3) The tabletop EUT was placed upon a non-metallic table 0.8m above the ground reference plane.
And for floor-standing arrangement, the EUT was placed on the horizontal ground reference plane,
4) The test was performed with a vertical ground reference plane. The rear of the EUT shall be 0.4 m
from the vertical ground reference plane. The vertical ground reference plane was bonded to the
horizontal ground reference plane. The LISN 1 was placed 0.8 m from the boundary of the unit under
test and bonded to a ground reference plane for LISNs mounted on top of the ground reference
plane. This distance was between the closest points of the LISN 1 and the EUT. All other units of the
EUT and associated equipment was at least 0.8 m from the LISN 2.
5) In order to find the maximum emission, the relative positions of equipment and all of the interface
cables must be changed according to ANSI C63.10 on conducted measurement.
Remark: LISN=Read Level+ Cable Loss+ LISN Factor
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
11 of 23
Mode:b; Line:Live Line
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
12 of 23
Mode:b; Line:Neutral Line
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
13 of 23
7.2 20dB Bandwidth
Test Requirement
Test Method:
Limit:
47 CFR Part 15, Subpart C 15.215
ANSI C63.10 (2013) Section 6.9
N/A
7.2.1 E.U.T. Operation
Operating Environment:
Atmospheric Pressure: 1010 mbar
Temperature:
21 °C
Humidity: 45 % RH
b:Charge + TX mode_Keep the EUT in charging and transmitting with modulation
Test mode
mode.
7.2.2 Test Setup Diagram
7.2.3 Measurement Procedure and Data
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
14 of 23
20dB bandwidth (kHz)
FL (MHz)
FH (MHz)
Limit(MHz)
Result
18.35
13.5507
13.5691
13.110 – 14.010
Pass
Test plot as follows:
* RBW 9 kHz
Delta 3 [T1 ]
0.17 dB
18.349358974 kHz
* VBW 30 kHz
Ref
67 dBµV
* Att
0 dB
SWT 5 ms
Marker 1 [T1 ]
28.79 dBµV
13.550785256 MHz
Marker 2 [T1 ]
49.82 dBµV
13.560000000 MHz
60
1 PK
MAXH
50
40
30
D1 29.82 dBµV
20
6DB
DC
10
-10
-20
-30
Center
13.56 MHz
5 kHz/
Span
50 kHz
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
15 of 23
7.3 Frequency tolerance
Test Requirement
Test Method:
Limit:
47 CFR Part 15, Subpart C 15.225(e)
ANSI C63.10 (2013) Section 6.8
1.356kHz
7.3.1 E.U.T. Operation
Operating Environment:
Temperature:
21 °C
7.3.2 Test Setup Diagram
Humidity:
45
% RH
Atmospheric Pressure: 1010
mbar
7.3.3 Measurement Procedure and Data
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
16 of 23
Nominal Operation Frequency: 13.56MHz
Test Conditions
Temp (℃)
Volt (V AC)
Test Result
(MHz)
Deviation
(kHz)
Limit
(kHz)
Tnom (-20)
Vnom (120)
13.56008
0.07
Pass
Tnom (-10)
Vnom (120)
13.56008
0.07
Pass
Tnom (0)
Vnom (120)
13.56008
0.09
Pass
Tnom (10)
Vnom (120)
13.56008
0.06
Pass
Tnom (20)
Vnom (120)
13.56008
0.08
Tnom (30)
Vnom (120)
13.56008
0.05
Tnom (40)
Vnom (120)
13.56008
0.08
Tnom (50)
Vnom (120)
13.56008
0.07
Vmin (102)
13.56009
0.09
Pass
Vmax (138)
13. 56007
0.07
Pass
±0.01%
(1.3560kHz)
Result
Pass
Pass
Tnom (20)
Note: Deviation (kHz) = (Test Result-13.56MHz)*1000
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
17 of 23
7.4 Radiated Emissions(9kHz-30MHz)
Test Requirement
Test Method:
Limit:
47 CFR Part 15, Subpart C 15.225(d) & 15.209
ANSI C63.10 (2013) Section 6.4&6.5
Frequency(MHz)
Field strength
(microvolts/meter)
Limit
(dBuV/m)
Limit @3m
(dBµV/m)
Measurement Distance
(meters)
0.009-0.490
2400/F(kHz)
48.5 ~ 13.8
128.5 ~ 93.8
300
0.490-1.705
24000/F(kHz)
33.8 ~ 23.0
73.8 ~ 63.0
30
1.705-30
30
29.5
69.5
30
30-88
100
40.0
40.0
88-216
150
43.5
43.5
216-960
200
46.0
46.0
960-1000
500
54.0
54.0
Above 1000
500
54.0
54.0
7.4.1 E.U.T. Operation
Operating Environment:
Atmospheric Pressure: 1010 mbar
Temperature:
21 °C
Humidity: 45 % RH
b:Charge + TX mode_Keep the EUT in charging and transmitting with modulation
Test mode
mode.
7.4.2 Test Setup Diagram
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
18 of 23
7.4.3 Measurement Procedure and Data
For testing performed with the loop antenna, the center of the loop was positioned 1 m above the
ground and positioned with its plane vertical at the specified distance from the EUT. During testing
the loop was rotated about its vertical axis for maximum response at each azimuth and also
investigated with the loop positioned in the horizontal plane. Only the worst position of vertical was
shown in the report.
Item
Freq.
Read
Level
Antenna
Factor
Cable
Result
Distance
Loss Level@3m Factor
Result
Leve
Limit Line
Over
Limit
(Mark)
(MHz)
(dBµV)
(dB/m)
(dB)
(dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m)
(dB)
0.16
25.09
19.98
0.05
45.12
80
-34.88
23.71
-58.59
QP
0.41
23.99
19.80
0.06
43.85
80
-36.15
15.26
-51.41
QP
0.65
21.78
19.61
0.07
41.46
40
1.46
31.39
-29.93
QP
1.57
20.56
19.36
0.08
40.00
40
23.74
-23.74
QP
6.27
22.25
19.60
0.09
41.94
40
1.94
29.5
-27.56
QP
13.55
33.37
19.30
0.12
52.79
40
12.79
29.5
-16.71
Peak
Detector
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
19 of 23
7.5 Radiated Emissions(30MHz-1GHz)
Test Requirement
Test Method:
Limit:
Frequency
47 CFR Part 15, Subpart C 15.225(d) & 15.209
ANSI C63.10 (2013) Section 6.4&6.5
Field strength
Limit
(microvolt/meter) (dBuV/m)
Remark
Measurement
distance (m)
30MHz-88MHz
100
40.0
Quasi-peak
88MHz-216MHz
150
43.5
Quasi-peak
216MHz-960MHz
200
46.0
Quasi-peak
960MHz-1GHz
500
54.0
Quasi-peak
7.5.1 E.U.T. Operation
Operating Environment:
Atmospheric Pressure: 1010 mbar
Temperature:
21 °C
Humidity: 45 % RH
b:Charge + TX mode_Keep the EUT in charging and transmitting with modulation
Test mode
mode.
7.5.2 Test Setup Diagram
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
20 of 23
7.5.3 Measurement Procedure and Data
a. The EUT was placed on the top of a rotating table 0.8 meters above the ground for below 1GHz at
a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of
the highest radiation.
b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on
the top of a variable-height antenna tower.
c. The antenna height is varied from one meter to four meters above the ground to determine the
maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set
to make the measurement.
d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was
tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was
tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find
the maximum reading.
e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum
Hold Mode.
f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing
could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that
did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method
as specified and then reported in a data sheet.
g. The radiation measurements are performed in X, Y, Z axis positioning. And found the X axis
positioning which it is worse case, only the test worst case mode is recorded in the report.
Remark: Level= Read Level+ Cable Loss+ Antenna Factor- Preamp Factor
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
21 of 23
Mode:b; Polarization:Horizontal
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
22 of 23
Mode:b; Polarization:Vertical
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.
Report No.: SHEM180400313202
Page:
23 of 23
8 Test Setup Photographs
Refer to the < Test Setup Photos-FCC >
9 EUT Constructional Details
Refer to the < External Photos > & < Internal Photos >.
- End of the Report -
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and,
for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the
limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of
its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from
exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized
alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown
in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
Download: K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Mirror Download [FCC.gov]K1A802MF Fingerprint Time Attendance Terminal Test Report  Hangzhou Hikvision Digital Technology Co., Ltd.
Document ID3887784
Application IDiRr4NddAQG5Lp6uwhfXLvA==
Document DescriptionTest Report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize87.7kB (1096299 bits)
Date Submitted2018-06-14 00:00:00
Date Available2018-06-14 00:00:00
Creation Date2018-06-12 11:39:15
Producing SoftwareGPL Ghostscript 8.64
Document Lastmod2018-06-12 03:39:16
Document TitleTest Report
Document CreatorPScript5.dll Version 5.2.2
Document Author: Vincent_Zhu

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Page Count                      : 23
Create Date                     : 2018:06:12 11:39:15+08:00
Title                           : Microsoft Word - SHEM180400313202CR RPT-FCC 15.225.doc
Producer                        : GPL Ghostscript 8.64
Author                          : Vincent_Zhu
Creator                         : PScript5.dll Version 5.2.2
Modify Date                     : 2018:06:12 03:39:16Z