UV5R Amateur Radio Test Report PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Amateur Radio

Page 1 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 2 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 3 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 4 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 5 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 6 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 7 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 8 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 9 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 10 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 11 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 12 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 13 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 14 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 15 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 16 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 17 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 18 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 19 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 20 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 21 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 22 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 23 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 24 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 25 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 26 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 27 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Page 28 of UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY

Page 1 of 28
FCC Test Report
Report No.: AGC02294180603FE08
FCC ID
: 2AJGM-UV5R
PRODUCT DESIGNATION
Dual Band FM Transceiver
BRAND NAME
BAOFENG, pofung
MODEL NAME
CLIENT
DATE OF ISSUE
Jun. 26, 2018
STANDARD(S)
FCC Part 15 Rules
REPORT VERSION
V 1.0
UV-5R, UV-5RC, UV-5RE, UV-5RE plus, UV-5R+Plus,
UV-5RA, GT-3
PO FUNG ELECTRONIC(HK) INTERNATIOANL
GROUP COMPANY
Attestation of Global Compliance (Shenzhen) Co., Ltd
CAUTION:
This report shall not be reproduced except in full without the written permission of the test
laboratory and shall not be quoted out of context.
Report No.: AGC02294180603FE08
Page 2 of 28
Report Revise Record
Report Version
Revise Time
Issued Date
Valid Version
Notes
V1.0
Jun. 26, 2018
Valid
Initial Release
Report No.: AGC02294180603FE08
Page 3 of 28
TABLE OF CONTENTS
1. VERIFICATION OF COMPLIANCE ................................................................................................................. 4
2. PRODUCT INFORMATION .............................................................................................................................. 5
3. IDENTIFICATION OF THE RESPONSIBLE TESTING LOCATION ............................................................... 6
4. SUPPORT EQUIPMENT LIST ......................................................................................................................... 7
5. SYSTEM DESCRIPTION .................................................................................................................................. 7
6. SUMMARY OF TEST RESULTS ..................................................................................................................... 8
7. FCC RADIATED EMISSION TEST .................................................................................................................. 9
7.1. TEST EQUIPMENT OF RADIATED EMISSION .................................................................................... 9
7.2. LIMITS OF RADIATED EMISSION TEST .............................................................................................. 9
7.3 BLOCK DIAGRAM OF RADIATED EMISSION TEST ............................................................................ 9
7.4 PROCEDURE OF RADIATED EMISSION TEST ................................................................................. 11
7.5 TEST RESULT OF RADIATED EMISSION TEST ................................................................................ 12
8. CONDUCTED EMISSION TEST .................................................................................................................... 14
8.1 PROVISIONS APPLICABLE ................................................................................................................. 14
8.2 MEASUREMENT PROCEDURE ........................................................................................................... 14
8.3 TEST SETUP BLOCK DIAGRAM ......................................................................................................... 15
8.4 TEST RESULT....................................................................................................................................... 16
9. ANTENNA CONDUCTED POWER FOR RECEIVERS ................................................................................. 18
APPENDIX 1 PHOTOGRAPHS OF TEST SETUP ............................................................................................ 21
APPENDIX 2 PHOTOGRAPHS OF EUT ........................................................................................................... 22
Report No.: AGC02294180603FE08
Page 4 of 28
1. VERIFICATION OF COMPLIANCE
Applicant
PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Address
3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong
Manufacturer
PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Address
3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong
Product Designation
Dual Band FM Transceiver
Brand name
BAOFENG,pofung
Test Model
UV-5R
Serial Model
UV-5RC, UV-5RE, UV-5RE plus, UV-5R+Plus, UV-5RA, GT-3
Serial Model Difference
All the same except for the model name, brand name and front appearance.
(UV-5R, UV-5RC, UV-5RE, UV-5RE plus, UV-5R+Plus, UV-5RA is BAOFENG /
GT-3WP is pofung)
Hardware Version
5R-VER22
Software Version
UV-5R
Measurement Procedure ANSI C63.4: 2014
Date of test:
Jun. 19, 2018 to Jun. 26, 2018
Deviation:
None
Condition of Test Sample Normal
The above equipment was tested by Attestation Of Global Compliance (Shenzhen) Co., Ltd. for compliance with
the requirements set forth in the FCC Rules and Regulations Part 15, the measurement procedure according to
ANSI C63.4:2014. This said equipment in the configuration described in this report shows the maximum
emission levels emanating from equipment are within the compliance requirements.
The test results of this report relate only to the tested sample identified in this report.
Tested By
Steven Zhou(Zhou Pengyun)
Jun. 26, 2018
Bart Xie(Xie Xiaobin)
Jun. 26, 2018
Forrest Lei(Lei Yonggang)
Authorized Officer
Jun. 26, 2018
Reviewed By
Approved By
Report No.: AGC02294180603FE08
Page 5 of 28
2. PRODUCT INFORMATION
The EUT is a Dual Band FM Transceiver designed for voice communication. It is designed by way of utilizing
the F3E modulation achieves the system operating.
A major technical description of EUT is described as following:
Communication Type
Voice / Tone only
Modulation
FM
RX Frequency Range
Rx:136 MHz -174 MHz, 400MHz -480MHz
Emission Type
F3E
Antenna Designation
Detachable
Antenna Gain
2.15dBi
Power Supply
DC 7.4V 1800mAh, charging with DC 8.4V.
INPUT:AC 100-240V~ 50/60Hz ,0.4A
Adapter Parameter
OUTPUT:DC 10V 0.5A
INPUT: DC 10V 0.5A
Charger Parameter
OUTPUT:DC 8.4V 0.4A
I/O Port Information (
Applicable
Not Applicable)
I/O Port of EUT
I/O Port Type
Q’TY
Cable
Tested with
DC Input Port
1.14m, Unshielded
Antenna Connect Port
Report No.: AGC02294180603FE08
Page 6 of 28
3. IDENTIFICATION OF THE RESPONSIBLE TESTING LOCATION
Test Site
Attestation of Global Compliance (Shenzhen) Co., Ltd
Location
1-2F., Bldg.2, No.1-4, Chaxi Sanwei Technical Industrial Park, Gushu, Xixiang,
Bao’an District B112-B113, Bldg.12, Baoan Bldg Materials Center, No.1 of Xixiang
Inner Ring Road, Baoan District, Shenzhen 518012
NVLAP LAB CODE
600153-0
Designation Number
CN5028
FCC Test Firm
Registration Number
682566
Attestation of Global Compliance(Shenzhen) Co., Ltd is accredited by National
Voluntary Laboratory Accreditation program, NVLAP Code 600153-0
Description
List Of Test Equipment:
TEST EQUIPMENT OF CONDUCTED EMISSION TEST
Equipment
Manufacturer
Model
S/N
Cal. Date
Cal. Due
TEST RECEIVER
R&S
ESCI
100096
Jun. 12, 2018
Jun. 11, 2019
AMN/LISN
R&S
ESH2-Z5
100086
Aug. 24, 2017
Aug. 23, 2018
TEST SOFTWARE
FR
EZ-EMC
AGC-CON03
--
--
TEST EQUIPMENT OF RADIATED EMISSION TEST
Equipment
Manufacturer
Model
S/N
Cal. Date
Cal. Due
TEST RECEIVER
R&S
ESPI
101206
Jun. 12, 2018
Jun. 11, 2019
ANTENNA
SCHWARZBECK
VULB9168
494
Sep. 27, 2017
Sep. 28, 2019
TEST RECEIVER
R&S
ESCI
100694
Jun. 12, 2018
Jun. 11, 2019
AMPLIFIER
Schwarzbeck
BBV 9718
9718-205
Jun. 12, 2018
Jun. 11, 2019
MF
MF-7802
MF780208285
--
--
ETS LINDGREN
3117
00034609
May. 17, 2017
May. 18, 2019
POSITIONING
CONTROLLER
HORN ANTENNA
Report No.: AGC02294180603FE08
Page 7 of 28
4. SUPPORT EQUIPMENT LIST
Device Type
Manufacturer
Model Name
Serial No.
Data Cable
Power Cable
--
--
--
--
--
--
5. SYSTEM DESCRIPTION
EUT test procedure:
1. Connect EUT and peripheral devices.
2. Power on the EUT, the EUT begins to work.
3. Make sure the EUT normal working.
EMC TEST MODES
No.
TEST MODES
Scanning mode
Scanning stopped/Receiving
Note: Only the result of the worst case was recorded in the report.
Report No.: AGC02294180603FE08
Page 8 of 28
6. SUMMARY OF TEST RESULTS
FCC Rules
Description Of Test
Result
§15.107
Conduction Emission
Compliant
§15.109
Radiated Emission
Compliant
§15.111
Antenna Conducted Power for receivers
Compliant
Report No.: AGC02294180603FE08
Page 9 of 28
7. FCC RADIATED EMISSION TEST
7.1. TEST EQUIPMENT OF RADIATED EMISSION
7.2. LIMITS OF RADIATED EMISSION TEST
Frequency
Distance
Maximum Field Strength Limit
(MHz)
(m)
(dBuV/m/ Q.P.)
30~88
41.0
88~216
45.0
216~960
48.0
960~2000
53.5
**Note: The lower limit shall apply at the transition frequency. Because the EUT RX frequency range
up to 480 MHz, so the upper the frequency range up to 2 GHz.
7.3 BLOCK DIAGRAM OF RADIATED EMISSION TEST
RADIATED EMISSION TEST SETUP 30MHz-1000MHz
Report No.: AGC02294180603FE08
Page 10 of 28
RADIATED EMISSION TEST SETUP ABOVE 1000MHz
Report No.: AGC02294180603FE08
Page 11 of 28
7.4 PROCEDURE OF RADIATED EMISSION TEST
1) The equipment was set up as per the test configuration to simulate typical actual usage per the user’s
manual. When the EUT is a tabletop system, a wooden turntable with a height of 0.8 meters is used which
is placed on the ground plane as per ANSI C63.4 (see Test Facility for the dimensions of the ground plane
used). When the EUT is floor-standing equipment, it is placed on the ground plane which has a 3-12 mm
non-conductive covering to insulate the EUT from the ground plane.
2) Support equipment, if needed, was placed as per ANSI C63.4.
3) All I/O cables were positioned to simulate typical actual usage as per ANSI C63.4.
4) The EUT received power by AC 120V/60Hz.
5) The antenna was placed at 3 meter away from the EUT as stated in FCC Part 15. The antenna connected
to the Analyzer via a cable and at times a pre-amplifier would be used.
6) The Analyzer / Receiver quickly scanned from 30MHz to 1000MHz. The EUT test program was started.
Emissions were scanned and measured rotating the EUT to 360 degrees and positioning the antenna 1 to 4
meters above the ground plane, in both the vertical and the horizontal polarization, to maximize the
emission reading level.
7) The test mode(s) were scanned during the test:
8) Recorded at least the six highest emissions. Emission frequency, amplitude, antenna position, polarization
and turntable position were recorded into a computer in which correction factors were used to calculate the
emission level and compare reading to the applicable limit and Q.P./Peak reading is presented. For
emissions below 1GHz, use 120KHz RBW and VBW>=3RBW for QP reading.
9) For emissions above 1GHz, use 1MHz RBW and 3MHz VBW for peak reading. Then 1MHz RBW and
10Hz VBW for average reading in spectrum analyzer.
10) When the radiated emissions limits are expressed in terms of the average value of the emissions, and
pulsed operation is employed, the measurement field strength shall be determined by averaging over one
complete pulse train, including blanking intervals, as long as the pulse train does not exceed 0.1 seconds.
As an alternative (provided the transmitter operates for longer than 0.1 seconds) or in cases where the
pulse train exceeds 0.1 seconds, the measured field strength shall be determined from the average
absolute voltage during a 0.1 second interval during which the field strength is at its maximum values.
11)If the emissions level of the EUT in peak mode was 3 dB lower than the average limit specified, then
testing will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not
have 3 dB margin will be repeated one by one using the quasi-peak method for below 1GHz.
12) For testing above 1GHz, the emissions level of the EUT in peak mode was lower than average limit (that
means the emissions level in peak mode also complies with the limit in average mode), then testing will be
stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average
mode again and reported.
13) In case the emission is lower than 30MHz, loop antenna has to be used for measurement and the
recorded data should be QP measured by receiver. High - Low scan is not required in this case.
14) The test data of the worst case condition (mode 1) was reported on the following Data page
Report No.: AGC02294180603FE08
Page 12 of 28
7.5 TEST RESULT OF RADIATED EMISSION TEST
Radiated Emission Test –Horizontal -3m Below 1G
Frequency
MHz
Polarization
Reading
dB(uV)
Factor
dB
Level
Limit
dB(uV/m) dB(uV/m)
(1/m)
PK
QP
Margin
dB
Pass/Fail
Height Angle
cm
deg
41.155
5.5
17.4
22.9
40.0
17.1
Pass
150.0
145.8
139.610
6.3
16.6
22.9
43.5
20.6
Pass
150.0
254.9
433.035
6.9
21.7
28.6
46.0
17.4
Pass
100.0
93.2
568.350
6.4
24.3
30.7
46.0
15.3
Pass
200.0
145.7
799.695
6.5
28.7
35.2
46.0
10.8
Pass
150.0
109.2
936.950
6.1
30.5
36.6
46.0
9.4
Pass
200.0
145.7
RESULT: PASS
Report No.: AGC02294180603FE08
Page 13 of 28
Radiated Emission Test –Vertical -3m Below 1G
Frequency
MHz
Polarization
Reading
dB(uV)
Factor
dB
Level
Limit
dB(uV/m) dB(uV/m)
(1/m)
PK
QP
Margin
dB
Pass/Fail
Height Angle
cm
deg
78.015
14.0
12.4
26.4
40.0
13.6
Pass
100.0
324.2
131.365
11.8
16.3
28.1
43.5
15.4
Pass
200.0
305.4
285.595
5.6
17.7
23.3
46.0
22.7
Pass
150.0
72.2
436.915
5.2
21.8
27.0
46.0
19.0
Pass
150.0
216.3
650.315
5.6
25.6
31.2
46.0
14.8
Pass
200.0
271.1
954.895
5.7
30.7
36.4
46.0
9.6
Pass
150.0
289.1
RESULT: PASS
Note: 1. Factor=Antenna Factor + Cable loss - Amplifier gain, Margin=Measurement-Limit.
2. The “Factor” value can be calculated automatically by software of measurement system.
3. Emissions range from 1GHz to 2GHz have 20dB margin. No recording in the test report.
4. Only the data of the worst case would be record in this test report.
Report No.: AGC02294180603FE08
Page 14 of 28
8. CONDUCTED EMISSION TEST
8.1 PROVISIONS APPLICABLE
For an intentional radiator that is designed to be connected to the public utility (AC) power line, the, the
radio frequency voltage that is conducted back onto the AC power line on any frequencies within the band
150 KHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50uH/50 ohms
line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be
based on the measurement of the radio frequency voltage between each power line and ground at the
power terminal. The lower limit applies at the boundary between the frequencies ranges.
Conducted Limit(dBuV)
Frequency of Emission (MHz)
Quasi-Peak
Average
0.15 – 0.5
66 to 56 *
56 to 46 *
0.5 – 5
56
46
5 – 30
60
50
* Decreases with the logarithm of the frequency.
8.2 MEASUREMENT PROCEDURE
(1) The equipment was set up as per the test configuration to simulate typical actual usage per the user’s
manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and
is placed on the ground plane as per ANSI C63.4 (see Test Facility for the dimensions of the ground
plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has
a 3-12 mm non-conductive covering to insulate the EUT from the ground plane.
(2) Support equipment, if needed, was placed as per ANSI C63.4.
(3) All I/O cables were positioned to simulate typical actual usage as per ANSI C63.4.
(4) The EUT received AC 120V/60Hz power through a Line Impedance Stabilization Network (LISN) which
supplied power source and was grounded to the ground plane.
(5) All support equipments received AC power from a second LISN, if any.
(6) The EUT test program was started. Emissions were measured on each current carrying line of the EUT
using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two
monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with
Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had
Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver.
(7) Analyzer / Receiver scanned from 150 KHz to 30MHz for emissions in each of the test modes.
During the above scans, the emissions were maximized by cable manipulation.
Report No.: AGC02294180603FE08
Page 15 of 28
8.3 TEST SETUP BLOCK DIAGRAM
Report No.: AGC02294180603FE08
Page 16 of 28
8.4 TEST RESULT
CONDUCTED EMISSION TEST – LINE L
RESULT: PASS
Report No.: AGC02294180603FE08
Page 17 of 28
CONDUCTED EMISSION TEST – LINE N
RESULT: PASS
Report No.: AGC02294180603FE08
Page 18 of 28
9. ANTENNA CONDUCTED POWER FOR RECEIVERS
LIMIT
The antenna conducted power of the receiver as defined in §15.111 shall not exceed the values given in the
following tables
Frequency Range
9 KHz to 2GHz
Limit
2.0 nW (-57 dBm )
TEST CONFIGURATION
TEST PROCEDURE
1. The receiver antenna terminal connected to a spectrum analyzer.
2. The test data of the worst case condition (mode 1) was reported on the following Data page.
Report No.: AGC02294180603FE08
Page 19 of 28
TEST RESULTS
Conducted Measurement (9 KHz to 150 KHz)
Conducted Measurement (150 KHz to 30MHz)
Report No.: AGC02294180603FE08
Page 20 of 28
Conducted Measurement (30MHz to 1GHz)
Conducted Measurement (1GHz to 2GHz)
PASS
Report No.: AGC02294180603FE08
Page 21 of 28
APPENDIX 1 PHOTOGRAPHS OF TEST SETUP
CONDUCTED EMISSION TEST SETUP
RADIATED EMISSION TEST SETUP
Report No.: AGC02294180603FE08
Page 22 of 28
APPENDIX 2 PHOTOGRAPHS OF EUT
TOTAL VIEW OF EUT
TOP VIEW OF EUT
Report No.: AGC02294180603FE08
Page 23 of 28
BOTTOM VIEW OF EUT
FRONT VIEW OF EUT
Report No.: AGC02294180603FE08
Page 24 of 28
BACK VIEW OF EUT
LEFT VIEW OF EUT
Report No.: AGC02294180603FE08
Page 25 of 28
RIGHT VIEW OF EUT
OPEN VIEW-1 OF EUT
Report No.: AGC02294180603FE08
Page 26 of 28
INTERNAL VIEW-1 OF EUT
INTERNAL VIEW-2 OF EUT
Report No.: AGC02294180603FE08
Page 27 of 28
INTERNAL VIEW-3 OF EUT
INTERNAL VIEW-4 OF EUT
Report No.: AGC02294180603FE08
Page 28 of 28
INTERNAL VIEW-5 OF EUT
----END OF REPORT----
Download: UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Mirror Download [FCC.gov]UV5R Amateur Radio Test Report  PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY
Document ID3928350
Application IDAsDlmXTIhNBSA7oXOT7xug==
Document Descriptiontest report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize244.31kB (3053932 bits)
Date Submitted2018-07-18 00:00:00
Date Available2018-07-18 00:00:00
Creation Date2018-07-03 19:30:41
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2018-07-04 20:23:57
Document Titletest report
Document CreatorMicrosoft® Office Word 2007
Document Author: lenovo

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Create Date                     : 2018:07:03 19:30:41+08:00
Creator Tool                    : Microsoft® Office Word 2007
Modify Date                     : 2018:07:04 20:23:57+08:00
Metadata Date                   : 2018:07:04 20:23:57+08:00
Format                          : application/pdf
Creator                         : lenovo
Title                           : 
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:4656c53b-7f93-4310-992a-f4d8b915d793
Instance ID                     : uuid:ae896ded-de35-4339-beb0-067f542afefa
Page Count                      : 28
Language                        : zh-CN
Author                          : lenovo