MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.

Creative Labs Pte. Ltd. CREATIVE METALLIX PLUS

Page 1 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 2 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 3 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 4 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 5 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 6 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 7 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 8 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 9 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 10 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 11 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 12 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 13 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 14 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 15 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 16 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 17 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 18 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 19 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 20 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 21 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 22 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 23 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 24 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 25 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 26 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 27 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 28 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 29 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 30 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 31 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 32 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 33 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 34 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 35 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 36 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 37 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 38 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 39 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 40 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 41 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 42 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 43 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 44 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 45 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 46 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 47 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 48 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 49 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 50 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 51 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 52 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 53 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 54 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 55 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 56 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 57 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 58 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 59 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Page 60 of MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.

SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
No. 1 Workshop, M-10, Middle section, Science & Technology Park,
Shenzhen, Guangdong, China 518057
Telephone:
Fax:
Email:
Report No.: SZEM170900985503
Page:
1 of 60
+86 (0) 755 2601 2053
+86 (0) 755 2671 0594
ee.shenzhen@sgs.com
TEST REPORT
Application No.:
Applicant:
Address of Applicant:
Manufacturer:
Address of Manufacturer:
SZEM1709009855CR
Creative Labs Pte. Ltd.
31 International Business Park, #03-01 Creative Resource, Singapore 609921
Creative Labs Pte. Ltd.
31 International Business Park, #03-01 Creative Resource, Singapore 609921
Equipment Under Test (EUT):
EUT Name:
CREATIVE METALLIX PLUS
Model No.:
MF8300
FCC ID:
2AJIV-MF8300
Trade mark:
CREATIVE
47 CFR Part 15, Subpart C 15.247
Standard(s) :
Date of Receipt:
2017-09-18
Date of Test:
2017-09-20 to 2017-09-24
Date of Issue:
2017-09-30
Test Result:
Pass*
* In the configuration tested, the EUT complied with the standards specified above.
Jack Zhang
EMC Laboratory Manager
The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report.
If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system
complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical
Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical
Approvals in writing.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
2 of 60
Revision Record
Version
Chapter
01
Date
2017-09-30
Modifier
Remark
Original
Authorized for issue by:
Vincent Chen /Project Engineer
Eric Fu /Reviewer
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
3 of 60
Test Summary
Radio Spectrum Technical Requirement
Item
Standard
Antenna
Requirement
47 CFR Part 15,
Subpart C 15.247
Radio Spectrum Matter Part
Item
Standard
Conducted
Emissions at AC
47 CFR Part 15,
Power Line (150kHzSubpart C 15.247
30MHz)
Method
Requirement
47 CFR Part 15,
Subpart C 15.203
& 15.247(c)
Result
Method
Requirement
Result
ANSI C63.10 (2013)
Section 6.2
47 CFR Part 15,
Subpart C 15.207
Pass
N/A
Minimum 6dB
Bandwidth
47 CFR Part 15,
Subpart C 15.247
ANSI C63.10 (2013)
Section 11.8.1
Conducted Peak
Output Power
47 CFR Part 15,
Subpart C 15.247
ANSI C63.10 (2013)
Section 11.9.1
Power Spectrum
Density
47 CFR Part 15,
Subpart C 15.247
ANSI C63.10 (2013)
Section 11.10.2
Conducted Band
Edges Measurement
47 CFR Part 15,
Subpart C 15.247
ANSI C63.10 (2013)
Section 11.13.3.2
Conducted Spurious
Emissions
47 CFR Part 15,
Subpart C 15.247
ANSI C63.10 (2013)
Section 11.11
Radiated Emissions
which fall in the
restricted bands
47 CFR Part 15,
Subpart C 15.247
ANSI C63.10 (2013)
Section 6.10.5
Radiated Spurious
Emissions
47 CFR Part 15,
Subpart C 15.247
ANSI C63.10 (2013)
Section 6.4,6.5,6.6
47 CFR Part 15,
Subpart C
15.247a(2)
47 CFR Part 15,
Subpart C
15.247(b)(3)
47 CFR Part 15,
Subpart C
15.247(e)
47 CFR Part 15,
Subpart C
15.247(d)
47 CFR Part 15,
Subpart C
15.247(d)
47 CFR Part 15,
Subpart C 15.205
& 15.209
47 CFR Part 15,
Subpart C 15.205
& 15.209
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
4 of 60
Contents
Page
COVER PAGE ..................................................................................................................................... 1
TEST SUMMARY ................................................................................................................................ 3
CONTENTS ......................................................................................................................................... 4
GENERAL INFORMATION .................................................................................................................. 6
4.1
4.2
4.3
4.4
4.5
4.6
4.7
DETAILS OF E.U.T. ......................................................................................................................... 6
DESCRIPTION OF SUPPORT UNITS .................................................................................................... 6
MEASUREMENT UNCERTAINTY ......................................................................................................... 7
TEST LOCATION ............................................................................................................................. 8
TEST FACILITY ............................................................................................................................... 8
DEVIATION FROM STANDARDS.......................................................................................................... 8
ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................. 8
EQUIPMENT LIST ............................................................................................................................... 9
RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................12
6.1
ANTENNA REQUIREMENT ................................................................................................................12
6.1.1 Test Requirement: ..................................................................................................................12
6.1.2 Conclusion ..............................................................................................................................12
RADIO SPECTRUM MATTER TEST RESULTS ................................................................................13
7.1
CONDUCTED EMISSIONS AT AC POWER LINE (150KHZ-30MHZ) ........................................................13
7.1.1 E.U.T. Operation .....................................................................................................................14
7.1.2 Test Setup Diagram ................................................................................................................14
7.1.3 Measurement Procedure and Data .........................................................................................14
7.2
MINIMUM 6DB BANDWIDTH .............................................................................................................17
7.2.1 E.U.T. Operation .....................................................................................................................17
7.2.2 Test Setup Diagram ................................................................................................................17
7.2.3 Measurement Procedure and Data .........................................................................................17
7.3
CONDUCTED PEAK OUTPUT POWER................................................................................................18
7.3.1 E.U.T. Operation .....................................................................................................................18
7.3.2 Test Setup Diagram ................................................................................................................18
7.3.3 Measurement Procedure and Data .........................................................................................18
7.4
POWER SPECTRUM DENSITY ..........................................................................................................19
7.4.1 E.U.T. Operation .....................................................................................................................19
7.4.2 Test Setup Diagram ................................................................................................................19
7.4.3 Measurement Procedure and Data .........................................................................................19
7.5
CONDUCTED BAND EDGES MEASUREMENT ......................................................................................20
7.5.1 E.U.T. Operation .....................................................................................................................21
7.5.2 Test Setup Diagram ................................................................................................................21
7.5.3 Measurement Procedure and Data .........................................................................................21
7.6
CONDUCTED SPURIOUS EMISSIONS .................................................................................................22
7.6.1 E.U.T. Operation .....................................................................................................................23
7.6.2 Test Setup Diagram ................................................................................................................23
7.6.3 Measurement Procedure and Data .........................................................................................23
7.7
RADIATED EMISSIONS WHICH FALL IN THE RESTRICTED BANDS ............................................................24
7.7.1 E.U.T. Operation .....................................................................................................................25
7.7.2 Test Setup Diagram ................................................................................................................25
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
5 of 60
7.7.3 Measurement Procedure and Data .........................................................................................26
7.8
RADIATED SPURIOUS EMISSIONS.....................................................................................................32
7.8.1 E.U.T. Operation .....................................................................................................................33
7.8.2 Test Setup Diagram ................................................................................................................33
7.8.3 Measurement Procedure and Data .........................................................................................34
APPENDIX ..........................................................................................................................................44
8.1
APPENDIX 15.247.....................................................................................................................44-60
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
6 of 60
General Information
4.1 Details of E.U.T.
Power supply:
Power by Li-ion battery DC 3.7V, 4400mAh
USB input: DC 5V, 1A
Cable:
Internal source
Frequency Range:
Bluetooth Version:
USB cable 65cm unshielded
26MHz
2402MHz to 2480MHz
BT 4.2 dual mode
This is for BLE mode
GFSK
40
Monopole
2dBi
Modulation Type:
Number of Channels:
Antenna Type:
Antenna Gain:
4.2 Description of Support Units
Description
Adapter
Manufacturer
Model No.
Serial No.
Apple
A1357 W010A051
REF. No.SEA0500
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
7 of 60
4.3 Measurement Uncertainty
No.
Item
Radio Frequency
Duty cycle
Occupied Bandwidth
RF conducted power
RF power density
Conducted Spurious emissions
RF Radiated power
Radiated Spurious emission test
10
11
12
Temperature test
Humidity test
Supply voltages
Time
Measurement Uncertainty
7.25 x 10-8
0.37%
3%
0.75dB
2.84dB
0.75dB
4.5dB (below 1GHz)
4.8dB (above 1GHz)
4.5dB (30MHz-1GHz)
4.8dB (1GHz-18GHz)
1°C
3%
1.5%
3%
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
8 of 60
4.4 Test Location
All tests were performed at:
SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch
No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China.
518057.
Tel: +86 755 2601 2053
Fax: +86 755 2671 0594
No tests were sub-contracted.
4.5 Test Facility
The test facility is recognized, certified, or accredited by the following organizations:
• CNAS (No. CNAS L2929)
CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC
Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration
Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration
Laboratories) for the competence in the field of testing.
• A2LA (Certificate No. 3816.01)
SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the
American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01.
• VCCI
The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services
Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with
Registration No.: G-823, R-4188, T-1153 and C-2383 respectively.
• FCC –Designation Number: CN1178
SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized
as an accredited testing laboratory.
Designation Number: CN1178. Test Firm Registration Number: 406779.
• Industry Canada (IC)
Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards
Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and
Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1,
4620C-2, 4620C-3.
4.6 Deviation from Standards
None
4.7 Abnormalities from Standard Conditions
None
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
9 of 60
Equipment List
Conducted Emissions at AC Power Line (150kHz-30MHz)
Equipment
Manufacturer
Model No
Inventory No
Cal Date
Cal Due Date
Shielding Room
ZhongYu Electron
GB-88
SEM001-06
2017-05-10
2018-05-10
Measurement Software
AUDIX
e3
V5.4.1221d
N/A
N/A
N/A
LISN
Rohde & Schwarz
ENV216
SEM007-01
2017-09-27
2018-09-27
LISN
ETS-LINDGREN
3816/2
SEM007-02
2017-04-14
2018-04-13
8-Wire ISN CAT 6
SCHWARZBECK
MESSELEKTRONIK
NTFM 8158
EMC2123
2017-06-23
2018-06-22
CAT5 8158 ISN 8Wire
SCHWARZBECK
MESSELEKTRONIK
CAT5 8158
EMC2124
2017-06-23
2018-06-22
8-Wire ISN CAT 3
SCHWARZBECK
MESSELEKTRONIK
CAT3 8158
EMC2126
2017-06-23
2018-06-22
Coaxial Cable
SGS
N/A
SEM024-01
2017-07-13
2018-07-12
Equipment
Manufacturer
Model No
Inventory No
Cal Date
Cal Due Date
DC Power Supply
ZhaoXin
RXN-305D
SEM011-02
2017-09-27
2018-09-27
Spectrum Analyzer
Rohde & Schwarz
FSP
SEM004-06
2017-09-27
2018-09-27
Measurement Software
JS Tonscend
JS1120-2
BT/WIFI V2.
N/A
N/A
N/A
Signal Generator
Rohde & Schwarz
SML03
SEM006-02
2017-04-14
2018-04-13
Power Meter
Rohde & Schwarz
NRVS
SEM014-02
2017-09-27
2018-09-27
Coaxial Cable
SGS
N/A
SEM031-01
2017-07-13
2018-07-12
RF Conducted
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
10 of 60
RE in Chamber
Equipment
Manufacturer
Model No
Inventory No
Cal Date
Cal Due Date
3m Semi-Anechoic
Chamber
AUDIX
N/A
SEM001-02
2017-05-02
2020-05-01
Measurement Software
AUDIX
e3 V8.20146-27
N/A
N/A
N/A
Spectrum Analyzer
Rohde & Schwarz
FSU43
SEM004-08
2017-04-14
2018-04-13
ETS-Lindgren
3142C
SEM003-02
2017-03-05
2020-03-05
Rohde & Schwarz
HF907
SEM003-07
2015-06-14
2018-06-14
Schwarzbeck
BBHA 9170
SEM003-14
2017-06-16
2020-06-15
HP
8447D
SEM005-02
2017-09-27
2018-09-27
Black Diamond
Series
BDLNA0118-352810
SEM005-05
2017-09-27
2018-09-27
Compliance
Directions Systems
Inc.
PAP-0126
SEM004-11
2016-12-02
2017-12-01
SEM005-08
2017-04-14
2018-04-13
BiConiLog Antenna
(26-3000MHz)
Horn Antenna
(1-18GHz)
Horn Antenna
(15GHz-40GHz)
Pre-amplifier
(0.1-1300MHz)
Low Noise Amplifier
(100MHz-18GHz)
Pre-amplifier
(0.1-26.5GHz)
Pre-amplifier
(26GHz-40GHz)
Compliance
Directions Systems PAP-2640-50
Inc.
DC Power Supply
Zhao Xin
RXN-305D
SEM011-02
2017-09-27
2018-09-27
Active Loop Antenna
ETS-Lindgren
6502
SEM003-08
2017-08-22
2020-08-21
Band filter
N/A
N/A
SEM023-01
N/A
N/A
Coaxial Cable
SGS
N/A
SEM024-01
2017-07-13
2018-07-12
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
11 of 60
RE in Chamber
Test Equipment
Manufacturer
Model No.
3m Semi-Anechoic
ETS-LINDGREN
N/A
Chamber
MXE EMI Receiver
Agilent Technologies
N9038A
(20Hz-8.4GHz)
BiConiLog Antenna
ETS-LINDGREN
3142C
(26-3000MHz)
Pre-amplifier
8447D
Agilent Technologies
(0.1-1300MHz)
Measurement
e3 V8.2014-6AUDIX
Software
27
Coaxial Cable
SGS
N/A
Inventory No.
Cal. Date
(yyyy-mmdd)
Cal. Due date
(yyyy-mmdd)
SEM001-01
2017-08-05
2020-08-04
SEM004-05
2017-09-27
2018-09-27
SEM003-02
2017-03-05
2020-03-05
SEM005-01
2017-04-14
2018-04-13
N/A
N/A
2017-07-13
2018-07-12
N/A
SEM024-01
General used equipment
Equipment
Humidity/ Temperature
Indicator
Humidity/ Temperature
Indicator
Manufacturer
Shanghai
Meteorological
Industry Factory
Shanghai
Meteorological
Industry Factory
Model No
Inventory No
Cal Date
Cal Due Date
ZJ1-2B
SEM002-03
2016-10-12
2017-10-12
ZJ1-2B
SEM002-04
2016-10-12
2017-10-12
Humidity/ Temperature
Indicator
Mingle
N/A
SEM002-08
2016-10-12
2017-10-12
Barometer
Changchun
Meteorological
Industry Factory
DYM3
SEM002-01
2017-04-18
2018-04-18
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
12 of 60
Radio Spectrum Technical Requirement
6.1 Antenna Requirement
6.1.1 Test Requirement:
47 CFR Part 15, Subpart C 15.203 & 15.247(c)
6.1.2 Conclusion
Standard Requirment:
An intentional radiator shall be designed to ensure that no antenna other than that furnished by the
responsible party shall be used with the device. The use of a permanently attached antenna or of an
antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit
so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or
electrical connector is prohibited.
15.247(b) (4) requirement:
The conducted output power limit specified in paragraph (b) of this section is based on the use of
antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this
section, if transmitting antennas of directional gain greater than 6 dBi are used, the conducted output
power from the intentional radiator shall be reduced below the stated values in paragraphs (b)(1),
(b)(2), and (b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the
antenna exceeds 6 dBi.
EUT Antenna:
The antenna is integrated on the main PCB and no consideration of replacement. The best case gain
of the antenna is 2dBi.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
13 of 60
Radio Spectrum Matter Test Results
7.1 Conducted Emissions at AC Power Line (150kHz-30MHz)
Test Requirement
Test Method:
Limit:
Frequency of emission(MHz)
47 CFR Part 15, Subpart C 15.207
ANSI C63.10 (2013) Section 6.2
Conducted limit(dBµV)
Quasi-peak
0.15-0.5
66 to 56*
0.5-5
56
5-30
60
*Decreases with the logarithm of the frequency.
Average
56 to 46*
46
50
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
14 of 60
7.1.1 E.U.T. Operation
Operating Environment:
Temperature:
25 °C
Atmospheric Pressure:
1010 mbar
Humidity: 45 % RH
Pretest these
e:Charge + TX mode_Keep the EUT in charging and continuously transmitting
mode to find the mode with GFSK modulation.
worst case:
7.1.2 Test Setup Diagram
7.1.3 Measurement Procedure and Data
1) The mains terminal disturbance voltage test was conducted in a shielded room.
2) The EUT was connected to AC power source through a LISN 1 (Line Impedance Stabilization
Network) which provides a 50ohm/50µH + 5ohm linear impedance. The power cables of all other units
of the EUT were connected to a second LISN 2, which was bonded to the ground reference plane in the
same way as the LISN 1 for the unit being measured. A multiple socket outlet strip was used to connect
multiple power cables to a single LISN provided the rating of the LISN was not exceeded.
3) The tabletop EUT was placed upon a non-metallic table 0.8m above the ground reference plane.
And for floor-standing arrangement, the EUT was placed on the horizontal ground reference plane,
4) The test was performed with a vertical ground reference plane. The rear of the EUT shall be 0.4 m
from the vertical ground reference plane. The vertical ground reference plane was bonded to the
horizontal ground reference plane. The LISN 1 was placed 0.8 m from the boundary of the unit under
test and bonded to a ground reference plane for LISNs mounted on top of the ground reference plane.
This distance was between the closest points of the LISN 1 and the EUT. All other units of the EUT and
associated equipment was at least 0.8 m from the LISN 2.
5) In order to find the maximum emission, the relative positions of equipment and all of the interface
cables must be changed according to ANSI C63.10 on conducted measurement.
Remark: LISN=Read Level+ Cable Loss+ LISN Factor
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
15 of 60
Mode:e; Line:Live Line
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
16 of 60
Mode:e; Line:Neutral Line
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
17 of 60
7.2 Minimum 6dB Bandwidth
Test Requirement
Test Method:
Limit:
47 CFR Part 15, Subpart C 15.247a(2)
ANSI C63.10 (2013) Section 11.8.1
≥500 kHz
7.2.1 E.U.T. Operation
Operating Environment:
Temperature:
25 °C
Atmospheric Pressure:
1010 mbar
Humidity: 55 % RH
Test mode
d:TX mode_Keep the EUT in continuously transmitting mode with GFSK modulation
7.2.2 Test Setup Diagram
7.2.3 Measurement Procedure and Data
The detailed test data see: Appendix 15.247
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
18 of 60
7.3 Conducted Peak Output Power
Test Requirement
Test Method:
Limit:
Frequency range(MHz)
902-928
2400-2483.5
5725-5850
47 CFR Part 15, Subpart C 15.247(b)(3)
ANSI C63.10 (2013) Section 11.9.1
Output power of the intentional radiator(watt)
1 for ≥50 hopping channels
0.25 for 25≤ hopping channels <50
1 for digital modulation
1 for ≥75 non-overlapping hopping channels
0.125 for all other frequency hopping systems
1 for digital modulation
1 for frequency hopping systems and digital modulation
7.3.1 E.U.T. Operation
Operating Environment:
Temperature:
25 °C
Atmospheric Pressure:
1010 mbar
Humidity: 55 % RH
Test mode
d:TX mode_Keep the EUT in continuously transmitting mode with GFSK modulation
7.3.2 Test Setup Diagram
7.3.3 Measurement Procedure and Data
The detailed test data see: Appendix 15.247
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
19 of 60
7.4 Power Spectrum Density
Test Requirement
Test Method:
Limit:
47 CFR Part 15, Subpart C 15.247(e)
ANSI C63.10 (2013) Section 11.10.2
≤8dBm in any 3 kHz band during any time interval of continuous
transmission
7.4.1 E.U.T. Operation
Operating Environment:
Temperature:
25 °C
Atmospheric Pressure:
1010 mbar
Humidity: 55 % RH
Test mode
d:TX mode_Keep the EUT in continuously transmitting mode with GFSK modulation
7.4.2 Test Setup Diagram
7.4.3 Measurement Procedure and Data
The detailed test data see: Appendix 15.247
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
20 of 60
7.5 Conducted Band Edges Measurement
Test Requirement
Test Method:
Limit:
47 CFR Part 15, Subpart C 15.247(d)
ANSI C63.10 (2013) Section 11.13.3.2
In any 100 kHz bandwidth outside the frequency band in which the spread
spectrum or digitally modulated intentional radiator is operating, the radio
frequency power that is produced by the intentional radiator shall be at least
20 dB below that in the 100 kHz bandwidth within the band that contains the
highest level of the desired power, based on either an RF conducted or a
radiated measurement, provided the transmitter demonstrates compliance
with the peak conducted power limits. If the transmitter complies with the
conducted power limits based on the use of RMS averaging over a time
interval, as permitted under paragraph (b)(3) of this section, the attenuation
required under this paragraph shall be 30 dB instead of 20 dB. Attenuation
below the general limits specified in §15.209(a) is not required. In addition,
radiated emissions which fall in the restricted bands, as defined in
§15.205(a), must also comply with the radiated emission limits specified in
§15.209(a) (see §15.205(c)
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
21 of 60
7.5.1 E.U.T. Operation
Operating Environment:
Temperature:
25 °C
Atmospheric Pressure:
1010 mbar
Humidity: 55 % RH
Test mode
d:TX mode_Keep the EUT in continuously transmitting mode with GFSK modulation
7.5.2 Test Setup Diagram
7.5.3 Measurement Procedure and Data
The detailed test data see: Appendix 15.247
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
22 of 60
7.6 Conducted Spurious Emissions
Test Requirement
Test Method:
Limit:
47 CFR Part 15, Subpart C 15.247(d)
ANSI C63.10 (2013) Section 11.11
In any 100 kHz bandwidth outside the frequency band in which the spread
spectrum or digitally modulated intentional radiator is operating, the radio
frequency power that is produced by the intentional radiator shall be at least
20 dB below that in the 100 kHz bandwidth within the band that contains the
highest level of the desired power, based on either an RF conducted or a
radiated measurement, provided the transmitter demonstrates compliance
with the peak conducted power limits. If the transmitter complies with the
conducted power limits based on the use of RMS averaging over a time
interval, as permitted under paragraph (b)(3) of this section, the attenuation
required under this paragraph shall be 30 dB instead of 20 dB. Attenuation
below the general limits specified in §15.209(a) is not required. In addition,
radiated emissions which fall in the restricted bands, as defined in
§15.205(a), must also comply with the radiated emission limits specified in
§15.209(a) (see §15.205(c)
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
23 of 60
7.6.1 E.U.T. Operation
Operating Environment:
Temperature:
25 °C
Atmospheric Pressure:
1010 mbar
Humidity: 55 % RH
Test mode
d:TX mode_Keep the EUT in continuously transmitting mode with GFSK modulation
7.6.2 Test Setup Diagram
7.6.3 Measurement Procedure and Data
The detailed test data see: Appendix 15.247
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
24 of 60
7.7 Radiated Emissions which fall in the restricted bands
Test Requirement
Test Method:
Measurement Distance:
Limit:
Frequency(MHz)
47 CFR Part 15, Subpart C 15.205 & 15.209
ANSI C63.10 (2013) Section 6.10.5
3m
Field
strength(microvolts/meter)
Measurement
distance(meters)
0.009-0.490
2400/F(kHz)
300
0.490-1.705
24000/F(kHz)
30
1.705-30.0
30
30
30-88
100
88-216
150
216-960
200
Above 960
500
Remark: The emission limits shown in the above table are based on measurements employing a
CISPR quasi-peak detector except for the frequency bands 9-90kHz, 110-490kHz and above 1000
MHz. Radiated emission limits in these three bands are based on measurements employing an
average detector, the peak field strength of any emission shall not exceed the maximum permitted
average limits specified above by more than 20 dB under any condition of modulation.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
25 of 60
7.7.1 E.U.T. Operation
Operating Environment:
Temperature:
24 °C
Atmospheric Pressure:
1010 mbar
Humidity: 54 % RH
Pretest these
d:TX mode_Keep the EUT in continuously transmitting mode with GFSK modulation
mode to find the e:Charge + TX mode_Keep the EUT in charging and continuously transmitting
worst case:
mode with GFSK modulation.
The worst case
for final test:
e:Charge + TX mode_Keep the EUT in charging and continuously transmitting
mode with GFSK modulation.
7.7.2 Test Setup Diagram
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
26 of 60
7.7.3 Measurement Procedure and Data
a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a
3 or 10 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of
the highest radiation.
b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters above the ground at
a 3 meter fully-anechoic chamber. The table was rotated 360 degrees to determine the position of the
highest radiation.
c. The EUT was set 3 or 10 meters away from the interference-receiving antenna, which was mounted
on the top of a variable-height antenna tower.
d. The antenna height is varied from one meter to four meters above the ground to determine the
maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set
to make the measurement.
e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was
tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was
tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the
maximum reading.
f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum
Hold Mode.
g. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing
could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did
not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as
specified and then reported in a data sheet.
h. Test the EUT in the lowest channel,the middle channel,the Highest channel.
i. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode, and
found the X axis positioning which it is the worst case.
j. Repeat above procedures until all frequencies measured was complete.
Remark: Level= Read Level+ Cable Loss+ Antenna Factor- Preamp Factor
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
27 of 60
Mode:e; Polarization:Horizontal; Modulation Type:GFSK; ; Channel:Low
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
28 of 60
Mode:e; Polarization:Vertical; Modulation Type:GFSK; ; Channel:Low
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
29 of 60
Mode:e; Polarization:Horizontal; Modulation Type:GFSK; ; Channel:High
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
30 of 60
Mode:e; Polarization:Vertical; Modulation Type:GFSK; ; Channel:High
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
31 of 60
Remark:
1) The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic
equation with a sample calculation is as follows:
Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor
2) As shown in this section, for frequencies above 1GHz, the field strength limits are based on average
limits. However, the peak field strength of any emission shall not exceed the maximum permitted
average limits specified above by more than 20 dB under any condition of modulation. So, only the peak
measurements were shown in the report.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
32 of 60
7.8 Radiated Spurious Emissions
Test Requirement
Test Method:
Measurement Distance:
Limit:
Frequency(MHz)
47 CFR Part 15, Subpart C 15.205 & 15.209
ANSI C63.10 (2013) Section 6.4,6.5,6.6
3m
Field
strength(microvolts/meter)
Measurement
distance(meters)
0.009-0.490
2400/F(kHz)
300
0.490-1.705
24000/F(kHz)
30
1.705-30.0
30
30
30-88
100
88-216
150
216-960
200
Above 960
500
Remark: The emission limits shown in the above table are based on measurements employing a
CISPR quasi-peak detector except for the frequency bands 9-90kHz, 110-490kHz and above 1000
MHz. Radiated emission limits in these three bands are based on measurements employing an
average detector, the peak field strength of any emission shall not exceed the maximum permitted
average limits specified above by more than 20 dB under any condition of modulation.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
33 of 60
7.8.1 E.U.T. Operation
Operating Environment:
Temperature:
25 °C
Atmospheric Pressure:
1010 mbar
Humidity: 55 % RH
Pretest these
d:TX mode_Keep the EUT in continuously transmitting mode with GFSK modulation
mode to find the e:Charge + TX mode_Keep the EUT in charging and continuously transmitting
worst case:
mode with GFSK modulation.
The worst case
for final test:
e:Charge + TX mode_Keep the EUT in charging and continuously transmitting
mode with GFSK modulation.
7.8.2 Test Setup Diagram
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
34 of 60
7.8.3 Measurement Procedure and Data
a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a
3 or 10 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of
the highest radiation.
b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters above the ground at
a 3 meter fully-anechoic chamber. The table was rotated 360 degrees to determine the position of the
highest radiation.
c. The EUT was set 3 or 10 meters away from the interference-receiving antenna, which was mounted
on the top of a variable-height antenna tower.
d. The antenna height is varied from one meter to four meters above the ground to determine the
maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set
to make the measurement.
e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was
tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was
tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the
maximum reading.
f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum
Hold Mode.
g. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing
could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did
not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as
specified and then reported in a data sheet.
h. Test the EUT in the lowest channel,the middle channel,the Highest channel.
i. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode, and
found the X axis positioning which it is the worst case.
j. Repeat above procedures until all frequencies measured was complete.
Remark: Level= Read Level+ Cable Loss+ Antenna Factor- Preamp Factor
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
35 of 60
30MHz~1GHz
QP value:
Mode:e; Polarization:Horizontal;
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
36 of 60
Mode:e; Polarization:Vertical;
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
37 of 60
Mode:e; Polarization:Horizontal; Modulation Type:GFSK; ; Channel:Low
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
38 of 60
Above 1GHz
Mode:e; Polarization:Vertical; Modulation Type:GFSK; ; Channel:Low
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
39 of 60
Mode:e; Polarization:Horizontal; Modulation Type:GFSK; ; Channel:middle
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
40 of 60
Mode:e; Polarization:Vertical; Modulation Type:GFSK; ; Channel:middle
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
41 of 60
Mode:e; Polarization:Horizontal; Modulation Type:GFSK; ; Channel:High
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
42 of 60
Mode:e; Polarization:Vertical; Modulation Type:GFSK; ; Channel:High
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
43 of 60
Remark:
1) The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic
equation with a sample calculation is as follows:
Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor
2) Scan from 9kHz to 25GHz, the disturbance above 18GHz and below 30MHz was very low, and the
above harmonics were the highest point could be found when testing, so only the above harmonics had
been displayed. The amplitude of spurious emissions from the radiator which are attenuated more than
20dB below the limit need not be reported.
3) As shown in this section, for frequencies above 1GHz, the field strength limits are based on average
limits. However, the peak field strength of any emission shall not exceed the maximum permitted
average limits specified above by more than 20 dB under any condition of modulation. So, only the peak
measurements were shown in the report.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
44 of 60
Appendix
8.1 Appendix 15.247
1.6dB Bandwidth
Test Mode
Test Channel
Ant
EBW[MHz]
Limit[MHz]
Verdict
BLE
2402
Ant1
0.738
>=0.5
PASS
BLE
2440
Ant1
0.723
>=0.5
PASS
BLE
2480
Ant1
0.720
>=0.5
PASS
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
45 of 60
6dB Bandwidth_BLE_2402_Ant1
Ref
10
* Att
10 dBm
Offset
10 dB
* RBW
100 kHz
* VBW
300 kHz
SWT 5 ms
2.402423000 GHz
Marker 1 [T1 ]
0.9 dB
2.35 dBm
2.402081000 GHz
Marker 2 [T1 ]
D1 -3.65 dBm
1 PK
VIEW
Marker 3 [T1 ]
-3.68 dBm
-3.79 dBm
2.401685000 GHz
-10
LVL
-20
-30
-40
3DB
-50
-60
-70
-80
-90
Center
2.402 GHz
300 kHz/
Span
3 MHz
6dB Bandwidth_BLE_2440_Ant1
Ref
10
* Att
10 dBm
Offset
10 dB
0.9 dB
* RBW
100 kHz
* VBW
300 kHz
SWT 5 ms
D1 -2.84 dBm
2.440396000 GHz
Marker 1 [T1 ]
Marker 3 [T1 ]
-2.91 dBm
3.16 dBm
2.440078000 GHz
Marker 2 [T1 ]
1 PK
VIEW
-3.05 dBm
2.439673000 GHz
-10
LVL
-20
-30
-40
3DB
-50
-60
-70
-80
-90
Center
2.44 GHz
300 kHz/
Span
3 MHz
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
46 of 60
6dB Bandwidth_BLE_2480_Ant1
Ref
10
* Att
10 dBm
Offset
10 dB
0.9 dB
* RBW
100 kHz
* VBW
300 kHz
SWT 5 ms
D1 -2.3 dBm
2.480414000 GHz
Marker 1 [T1 ]
Marker 3 [T1 ]
-2.42 dBm
3.70 dBm
2.480072000 GHz
Marker 2 [T1 ]
1 PK
VIEW
-2.31 dBm
2.479694000 GHz
-10
LVL
-20
-30
-40
3DB
-50
-60
-70
-80
-90
Center
2.48 GHz
300 kHz/
Span
3 MHz
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
47 of 60
2.Maximum peak conducted output power
Test Mode
Test Channel
Ant
Power[dBm]
Limit[dBm]
Verdict
BLE
2402
Ant1
0.58
<30
PASS
BLE
2440
Ant1
1.4
<30
PASS
BLE
2480
Ant1
1.79
<30
PASS
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
48 of 60
Maximum peak conducted output power_BLE_2402_Ant1
Ref
10
* Att
10 dBm
Offset
10 dB
* RBW
3 MHz
* VBW
10 MHz
Marker 1 [T1 ]
0.58 dBm
* SWT
100 ms
2.401880000 GHz
0.9 dB
1 PK
VIEW
-10
LVL
-20
-30
-40
3DB
-50
-60
-70
-80
-90
Center
2.402 GHz
1 MHz/
Span
10 MHz
Maximum peak conducted output power_BLE_2440_Ant1
Ref
10
* Att
10 dBm
Offset
10 dB
* RBW
3 MHz
* VBW
10 MHz
Marker 1 [T1 ]
1.40 dBm
* SWT
100 ms
2.439950000 GHz
0.9 dB
1 PK
VIEW
-10
LVL
-20
-30
-40
3DB
-50
-60
-70
-80
-90
Center
2.44 GHz
1 MHz/
Span
10 MHz
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
49 of 60
Maximum peak conducted output power_BLE_2480_Ant1
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
50 of 60
3.Maximum Peak power spectral density
Verdict
-17.94
Limit[dBm/3kHz
<8.00
Ant1
-17.08
<8.00
PASS
Ant1
-16.44
<8.00
PASS
Test Mode
Test Channel
Ant
PSD[dBm/3kHz]
BLE
2402
Ant1
BLE
2440
BLE
2480
PASS
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
51 of 60
Maximum Peak power spectral density_BLE_2402_Ant1
Ref
10
* Att
10 dBm
Offset
10 dB
* RBW
3 kHz
* VBW
10 kHz
Marker 1 [T1 ]
-17.94 dBm
SWT 170 ms
2.402051000 GHz
0.9 dB
1 PK
VIEW
-10
LVL
-20
-30
-40
3DB
-50
-60
-70
-80
-90
Center
2.402 GHz
150 kHz/
Span
1.5 MHz
Maximum Peak power spectral density_BLE_2440_Ant1
Ref
10
* Att
10 dBm
Offset
10 dB
* RBW
3 kHz
* VBW
10 kHz
Marker 1 [T1 ]
-17.08 dBm
SWT 170 ms
2.440052500 GHz
0.9 dB
1 PK
VIEW
-10
LVL
-20
-30
-40
3DB
-50
-60
-70
-80
-90
Center
2.44 GHz
150 kHz/
Span
1.5 MHz
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
52 of 60
Maximum Peak power spectral density_BLE_2480_Ant1
Ref
10
* Att
10 dBm
Offset
10 dB
* RBW
3 kHz
* VBW
10 kHz
Marker 1 [T1 ]
-16.44 dBm
SWT 170 ms
2.480052500 GHz
0.9 dB
1 PK
VIEW
-10
LVL
-20
-30
-40
3DB
-50
-60
-70
-80
-90
Center
2.48 GHz
150 kHz/
Span
1.5 MHz
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
53 of 60
4.Band-edge for RF Conducted Emissions
Test
Mode
Test
Channel
Ant
Carrier
Power[dBm]
Max. Spurious
Level
[dBm]
Limit
[dBm]
Verdict
BLE
2402
Ant1
2.420
-51.126
<-17.58
PASS
BLE
2480
Ant1
3.590
-39.683
<-16.41
PASS
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
54 of 60
Band-edge for RF Conducted Emissions_BLE_2402_Ant1
Ref
10
* Att
10 dBm
Offset
10 dB
* RBW
100 kHz
* VBW
300 kHz
SWT 10 ms
Marker 4 [T1 ]
-51.13 dBm
2.389618000 GHz
Marker 1 [T1 ]
0.9 dB
2.42 dBm
2.402073000 GHz
SGL
Marker 2 [T1 ]
1 PK
MAXH
-35.70 dBm
2.400000000 GHz
-10
LVL
Marker 3 [T1 ]
-53.46 dBm
D1 -17.58 dBm
-20
2.390000000 GHz
-30
-40
3DB
-50
-60
-70
-80
-90
Start
2.31 GHz
9.4 MHz/
Stop
2.404 GHz
Band-edge for RF Conducted Emissions_BLE_2480_Ant1
Ref
10
* Att
10 dBm
Offset
10 dB
* RBW
100 kHz
* VBW
300 kHz
SWT 10 ms
Marker 4 [T1 ]
-39.68 dBm
2.483522000 GHz
Marker 1 [T1 ]
0.9 dB
3.59 dBm
2.480079000 GHz
SGL
Marker 2 [T1 ]
1 PK
MAXH
-39.70 dBm
2.483500000 GHz
-10
LVL
Marker 3 [T1 ]
-54.77 dBm
D1 -16.41 dBm
-20
2.500000000 GHz
-30
-40
3DB
-50
-60
-70
-80
-90
Start
2.478 GHz
2.2 MHz/
Stop
2.5 GHz
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation
of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its
intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all
their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or
falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report
refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900985503
Page:
55 of 60
5.RF Conducted Spurious Emissions
VBW
[kHz]
Pref[dBm
Max.
Level
[dBm]
Limit Verdic
[dBm]
1000
3000
2.65
-45.880
Download: MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Mirror Download [FCC.gov]MF8300 CREATIVE METALLIX PLUS Test Report SZEM170900985503 BLE RPT Creative Labs Pte. Ltd.
Document ID3634613
Application IDYObFynNjLNft06nZzXKn1g==
Document DescriptionTest report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize107.22kB (1340251 bits)
Date Submitted2017-11-10 00:00:00
Date Available2017-11-10 00:00:00
Creation Date2017-11-10 11:07:21
Producing SoftwareGPL Ghostscript 8.64
Document Lastmod2017-11-10 03:07:24
Document TitleSZEM170900985503 BLE RPT
Document CreatorPScript5.dll Version 5.2.2
Document Author: kate_bian

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Page Count                      : 60
Create Date                     : 2017:11:10 11:07:21+08:00
Title                           : Microsoft Word - SZEM170900985503 BLE RPT.doc
Producer                        : GPL Ghostscript 8.64
Author                          : kate_bian
Creator                         : PScript5.dll Version 5.2.2
Modify Date                     : 2017:11:10 03:07:24Z