FCC ID 2AJVQ-MWH640S

TCB	GRANT OF EQUIPMENT AUTHORIZATION	TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:

PHOENIX TESTLAB GmbH Koenigswinkel 10 32825 Blomberg, Germany

Date of Grant: 06/20/2024 Application Dated: 06/20/2024

Qingdao Intelligent&Precise Electronics Co.,Ltd

No218,Qianwangang Road

Qingdao Economic&Technological Development ZoneP.O. Box 266071,

Qingdao, 266071 China

Attention: Haining Wang , Certification Engineer

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	2AJVQ-MWH640S
Name of Grantee:	Qingdao Intelligent&Precise Electronics Co.,Ltd
Equipment Class:	Digital Transmission System
Notes:	WIFI/BT module
Modular Type:	Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
CC	15C	2402.0  -  2480.0	0.002
CC	15C	2412.0  -  2462.0	0.185

Output power is maximum peak conducted. This device supports WIFI 802.11 b/g/n/ax20 and 40 MHz channel bandwidth. This device has integrated DTS and NII transmitters certified under the same FCC ID. Modular Approval for mobile RF Exposure conditions, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Approval is limited to OEM installation only. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-users must be provided with transmitter operating conditions for satisfying RF exposure compliance. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only the antenna(s) listed in this filing can be used with this device. Use of additional antenna(s) are subject to the requirements of 15.204(c)(4). The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369.

CC:	This device is certified pursuant to two different Part 15 rules sections.

COPY	FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION	COPY
Certification

Qingdao Intelligent&Precise Electronics Co.,Ltd No218,Qianwangang Road Qingdao Economic&Technological Development ZoneP.O. Box 266071, Qingdao, 266071 China

Date of Grant: 06/20/2024 Application Dated: 06/20/2024

Attention: Haining Wang , Certification Engineer

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	2AJVQ-MWH640S
Name of Grantee:	Qingdao Intelligent&Precise Electronics Co.,Ltd
Equipment Class:	Digital Transmission System
Notes:	WIFI/BT module
Modular Type:	Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
CC	15C	2402.0  -  2480.0	0.002
CC	15C	2412.0  -  2462.0	0.185

Output power is maximum peak conducted. This device supports WIFI 802.11 b/g/n/ax20 and 40 MHz channel bandwidth. This device has integrated DTS and NII transmitters certified under the same FCC ID. Modular Approval for mobile RF Exposure conditions, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Approval is limited to OEM installation only. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-users must be provided with transmitter operating conditions for satisfying RF exposure compliance. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only the antenna(s) listed in this filing can be used with this device. Use of additional antenna(s) are subject to the requirements of 15.204(c)(4). The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369.

CC:	This device is certified pursuant to two different Part 15 rules sections.

TCB Grant - Application ug1A+JytSLubY72CH5n5Cg==

Mail To:

TCB	GRANT OF EQUIPMENT AUTHORIZATION	TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:

PHOENIX TESTLAB GmbH Koenigswinkel 10 32825 Blomberg, Germany

Date of Grant: 06/20/2024 Application Dated: 06/20/2024

Qingdao Intelligent&Precise Electronics Co.,Ltd

No218,Qianwangang Road

Qingdao Economic&Technological Development ZoneP.O. Box 266071,

Qingdao, 266071 China

Attention: Haining Wang , Certification Engineer

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	2AJVQ-MWH640S
Name of Grantee:	Qingdao Intelligent&Precise Electronics Co.,Ltd
Equipment Class:	Unlicensed National Information Infrastructure TX
Notes:	WIFI/BT module
Modular Type:	Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
CC	15E	5180.0  -  5240.0	0.034
CC	15E	5260.0  -  5320.0	0.024

Output power is maximum average conducted. This device supports IEEE 802.11 a/n/ac/ax 20 and 40 MHz channel bandwidths. This device has integrated DTS and NII transmitters certified under the same FCC ID. Modular Approval for mobile RF Exposure conditions, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Approval is limited to OEM installation only. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-users must be provided with transmitter operating conditions for satisfying RF exposure compliance. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only the antenna(s) listed in this filing can be used with this device. Use of additional antenna(s) are subject to the requirements of 15.204(c)(4). The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369.

CC:	This device is certified pursuant to two different Part 15 rules sections.

COPY	FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION	COPY
Certification

Qingdao Intelligent&Precise Electronics Co.,Ltd No218,Qianwangang Road Qingdao Economic&Technological Development ZoneP.O. Box 266071, Qingdao, 266071 China

Date of Grant: 06/20/2024 Application Dated: 06/20/2024

Attention: Haining Wang , Certification Engineer

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	2AJVQ-MWH640S
Name of Grantee:	Qingdao Intelligent&Precise Electronics Co.,Ltd
Equipment Class:	Unlicensed National Information Infrastructure TX
Notes:	WIFI/BT module
Modular Type:	Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
CC	15E	5180.0  -  5240.0	0.034
CC	15E	5260.0  -  5320.0	0.024

Output power is maximum average conducted. This device supports IEEE 802.11 a/n/ac/ax 20 and 40 MHz channel bandwidths. This device has integrated DTS and NII transmitters certified under the same FCC ID. Modular Approval for mobile RF Exposure conditions, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Approval is limited to OEM installation only. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-users must be provided with transmitter operating conditions for satisfying RF exposure compliance. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only the antenna(s) listed in this filing can be used with this device. Use of additional antenna(s) are subject to the requirements of 15.204(c)(4). The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369.

CC:	This device is certified pursuant to two different Part 15 rules sections.

Mail To: