TL104AMDJA Tapplock one User Manual PowerPoint Presentation TappLock .
TappLock . Tapplock one
Tapplock one User Manual World’s first smart fingerprint padlock Tapplock.com Cutting-edge fingerprint technology • • • Unlocks in 0.8 seconds Stores up to 500 fingerprint Adaptive algorithm: faster and more accurate access each time you use it Shareable wireless access • • • Supports wireless Bluetooth access via the Tapplock app. Share & control access remotely to unlimited users, View access history with time and location. Water and weather resistant • • • Water resistant up to IP66 Rust-proof & rain-proof Fully functional between -10C and 60C *** WARNING*** Tapplock one is NOT waterproof when it is unlocked. Water entered through open socket may cause permanent damage. Rechargeable battery • • Up to one year battery life per 2 hours charge time Check remaining power using the Tapplock app Unbreakable durability • • Zamak 3 zinc alloy metal body with cut-resistant stainless steel shackle Double-layered design with anti-shim and anti-pry capabilities makes Tapplock virtually unbreakable Morse code backup access • Setup morse code access using the power button in case a user's fingerprint isn't enrolled and the phone ran out of batteries. Overview Status indicator Fingerprint sensor Power / mode button Charge port Quick start 1. Download the Tapplock app from Google Playstore or iOS App Store 2. Register / log in on the Tapplock app and follow instructions to setup your new Tapplock ** Make sure Bluetooth is turned on in your phone settings before beginning to setup the lock 3 ways to unlock Tapplock one is equipped with multiple access capability to allow for maximum convenience and flexibility. Fingerprint access: 0.8 seconds Bluetooth access: Bluetooth access via the Tapplock app using your smartphone Morse-code access: backup access using long-short combinations Fingerprint Mode Status Indicator Power Button • To turn on Tapplock, press the Power Button located below the rim. The Status Indicator light should be white, and your Tapplock should be ready to unlock with your fingerprint. (If you are having trouble getting to Fingerprint Mode, hold down the Power Button until the Status Indicator light turns off, putting your lock in sleep mode. Then press the Power Button to enter Fingerprint Mode) ** Tapplock one will automatically enter sleep mode after 10 seconds of inactivity. This increases the lifespan of your battery. Bluetooth Mode Status Indicator Power Button • Connect your phone using the Bluetooth Mode to: • Add new Tapplock to your account • Unlock with your phone • Setup / remove fingerprints • Setup morse code • Press the Power Button twice (2) to enter Bluetooth Mode for phone pairing. The Status Indicator light should be blue. (If you are having trouble getting to Bluetooth Mode, hold down the Power Button until the Status Indicator light turns off, putting your lock in sleep mode. Then press the Power Button twice to enter Bluetooth Mode) Morse-code Instructions Status Indicator Power Button • Morse-code is a backup access mode. It allows you to unlock your device using long / short combinations of pressing the Power Button. Morse-code allows access to your lock without your fingerprint or your phone. • Follow instructions in the Tapplock app to setup your custom morse-code • Press the Power Button three (3) times to enter Morse Code mode. The Status Indicator light should be green. (If you are having trouble getting to Morse Code mode, hold down the Power Button until the Status Indicator light turns off, putting your lock in sleep mode. Then press the Power Button three times until the Status Indicator light turns green) Status Indicator The status indicator is the visual cue to understanding your Tapplock one. Refer to table below to understand what each color means. White Fingerprint mode Status Indicator Green √ √ Fingerprint error √ √ Low battery Blinking Charging Breathing 100% charged Upgrading firmware Yellow Blinking Bluetooth connected Morse-code mode Red √ Bluetooth searching Fingerprint recognized Blue √ √ This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le fonctionnement. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. le dispositif a été évalué à satisfaire l'exigence générale de l'exposition aux rf. l'appareil peut être utilisé dans des conditions d'exposition portatif sans restriction. FCC notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Visit Tapplock.com for newest updates, instructions and FAQ. Contact us by emailing: firstname.lastname@example.org Copyright © Tapplock Corp.
Source Exif Data [exif.tools]:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 16 Language : en-CA Tagged PDF : Yes XMP Toolkit : 3.1-701 Producer : Microsoft® PowerPoint® 2016 Title : PowerPoint Presentation Creator : Michael Creator Tool : Microsoft® PowerPoint® 2016 Create Date : 2017:02:14 19:19:12-05:00 Modify Date : 2017:02:14 19:19:12-05:00 Document ID : uuid:80FAA474-CCCA-43E7-9C66-DFAD12E2E22F Instance ID : uuid:80FAA474-CCCA-43E7-9C66-DFAD12E2E22F Author : Michael