AMP6700 AMP 6700 Test Report Advanced Mobile Payment Inc.

Advanced Mobile Payment Inc. AMP 6700

Page 1 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 2 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 3 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 4 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 5 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 6 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 7 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 8 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 9 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 10 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 11 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 12 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 13 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 14 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 15 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 16 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 17 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 18 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 19 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 20 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 21 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 22 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 23 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Page 24 of AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.

FCC PART 15.225
TEST REPORT
For
Advanced Mobile Payment Inc.
Units 401-403, 15 Wertheim Court. Richmond Hill, Ontario L4B 3H7 Canada
FCC ID: 2AKJB-AMP6700
Report Type:
Product Type:
Original Report
AMP 6700
Report Number:
Report Date:
RSZ180809001-00D
2018-10-16
Simon Wang
Reviewed By:
RF Engineer
Prepared By:
Bay Area Compliance Laboratories Corp. (Shenzhen)
6/F., West Wing, Third Phase of Wanli Industrial
Building, Shihua Road, Futian Free Trade Zone,
Shenzhen, Guangdong, China
Tel: +86-755-33320018
Fax: +86-755-33320008
www.baclcorp.com.cn
Note: This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA* or any
agency of the Federal Government. * This report may contain data that are not covered by the A2LA accreditation and are marked
with an asterisk “*”.
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
TABLE OF CONTENTS
GENERAL INFORMATION .......................................................................................................................................3
PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................3
OBJECTIVE ...................................................................................................................................................................3
RELATED SUBMITTAL(S)/GRANT(S) .............................................................................................................................3
TEST METHODOLOGY ..................................................................................................................................................3
MEASUREMENT UNCERTAINTY ....................................................................................................................................3
SYSTEM TEST CONFIGURATION ..........................................................................................................................5
JUSTIFICATION .............................................................................................................................................................5
EUT EXERCISE SOFTWARE ..........................................................................................................................................5
EQUIPMENT MODIFICATIONS .......................................................................................................................................5
SUPPORT EQUIPMENT LIST AND DETAILS ....................................................................................................................5
EXTERNAL I/O CABLE..................................................................................................................................................5
BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................6
SUMMARY OF TEST RESULTS ...............................................................................................................................8
TEST EQUIPMENT LIST ...........................................................................................................................................9
FCC§15.203 - ANTENNA REQUIREMENT............................................................................................................10
APPLICABLE STANDARD ............................................................................................................................................10
ANTENNA CONNECTED CONSTRUCTION ....................................................................................................................10
FCC §15.207 – AC LINE CONDUCTED EMISSION .............................................................................................11
APPLICABLE STANDARD ............................................................................................................................................11
EUT SETUP ................................................................................................................................................................11
EMI TEST RECEIVER SETUP .......................................................................................................................................11
TEST PROCEDURE ......................................................................................................................................................12
CORRECTED FACTOR & MARGIN CALCULATION .......................................................................................................12
TEST RESULTS SUMMARY ..........................................................................................................................................12
TEST DATA ................................................................................................................................................................12
FCC§15.225, §15.205 & §15.209 - RADIATED EMISSIONS TEST ......................................................................17
APPLICABLE STANDARD ............................................................................................................................................17
EUT SETUP ................................................................................................................................................................17
EMI TEST RECEIVER SETUP .......................................................................................................................................17
CORRECTED AMPLITUDE & MARGIN CALCULATION .................................................................................................18
TEST RESULTS SUMMARY ..........................................................................................................................................18
TEST DATA ................................................................................................................................................................18
FCC§15.225(E) - FREQUENCY STABILITY..........................................................................................................22
APPLICABLE STANDARD ............................................................................................................................................22
TEST PROCEDURE ......................................................................................................................................................22
TEST DATA ................................................................................................................................................................22
FCC§15.215(C) - 20DB EMISSION BANDWIDTH ................................................................................................23
REQUIREMENT ...........................................................................................................................................................23
TEST PROCEDURE ......................................................................................................................................................23
TEST DATA ................................................................................................................................................................23
FCC Part 15.225
Page 2 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
GENERAL INFORMATION
Product Description for Equipment under Test (EUT)
The Advanced Mobile Payment Inc.’s product, model number: AMP 6700 (FCC ID: 2AKJB-AMP6700) or
the "EUT" in this report was a AMP 6700, which was measured approximately: 19.7 cm (L) * 19.2 cm (W)
*4.4 cm (H), rated with input voltage: DC 9.5V from adapter.
Adapter Information:
Model: ADS-25SG-12-2 09524E
Input: AC 100-240V, 50/60Hz, Max. 0.7 A
Output: DC 9.5V, 2.5A
*All measurement and test data in this report was gathered from production sample serial number: 180809001.
(Assigned by BACL, Shenzhen). The EUT supplied by the applicant was received on 2018-08-09.
Objective
This Type approval report is prepared on behalf of Advanced Mobile Payment Inc. in accordance with Part
2- Subpart J, and Part 15-Subparts A and C of the Federal Communication Commissions rules.
The objective is to determine the compliance of the EUT with FCC rules, section 15.203, 15.205, 15.207,
15.209 and 15.225.
Related Submittal(s)/Grant(s)
FCC Part 15B JAB and Part 15.247 DSS & DTS submissions with FCC ID: 2AKJB-AMP6700.
Test Methodology
All measurements contained in this report were conducted with ANSI C63.10-2013, American National
Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices.
All emissions measurement was performed at Bay Area Compliance Laboratories Corp. (Shenzhen). The
radiated testing was performed at an antenna-to-EUT distance of 3 meters.
Measurement Uncertainty
Parameter
uncertainty
Occupied Channel Bandwidth
±5%
RF Output Power with Power meter
±0.5dB
RF conducted test with spectrum
±1.5dB
AC Power Lines Conducted Emissions
±1.95dB
All emissions, radiated
±4.88dB
Temperature
±3℃
Humidity
±6%
Supply voltages
±0.4%
FCC Part 15.225
Page 3 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
Test Facility
The Test site used by Bay Area Compliance Laboratories Corp. (Shenzhen) to collect test data is located
on the 6/F., West Wing, Third Phase of Wanli Industrial Building, Shihua Road, Futian Free Trade Zone,
Shenzhen, Guangdong, China.
The test site has been approved by the FCC under the KDB 974614 D01 and is listed in the FCC Public
Access Link (PAL) database, FCC Registration No.: 342867, the FCC Designation No.: CN1221.
The test site has been registered with ISED Canada under ISED Canada Registration Number 3062B.
FCC Part 15.225
Page 4 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
SYSTEM TEST CONFIGURATION
Justification
The system was configured for testing in a typical fashion (as normally used by a typical user).
EUT Exercise Software
No Exercise Software was used.
Equipment Modifications
No modification on the EUT.
Support Equipment List and Details
Manufacturer
Description
Model
Serial Number
Lenovo
Notebook
SR860
100000633225
Lenovo
Notebook
Air 15
100897564
Lenovo
Mouse
M300
11093844046
Philip
Earphone
SHE3705BK
28232617325
N/A
POE
PSE801FM
N/A
External I/O Cable
Cable Description
Length (m)
From/Port
To
Un-Shielding Detachable DC Cable
1.2
EUT
Adapter
Un-shielding Detachable AC Cable
0.8
Adapter
Receptacle
Un-shielding Detachable Earphone Cable
0.8
EUT
Earphone
Un-shielding Undetachable AC Cable
1.0
Receptacle
LISN
Un-shielding Detachable RJ45 Cable
0.8
EUT
POE
Un-shielding Detachable AC Cable
1.0
POE
LISN
FCC Part 15.225
Page 5 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
Block Diagram of Test Setup
Adapter power supply:
For conducted emission:
LISN
EUT
Adapter
10cm
10cm
Notebook
Receptacle
Earphone
1.0 Meter
Notebook
Mouse
Non-Conductive Table
80 cm above Ground Plane
1.5 Meters
FCC Part 15.225
Page 6 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
For POE Supply:
For conducted emission:
LISN
EUT
1.0 Meter
Earphone
Notebook
POE
10cm
Mouse
Non-Conductive Table
80 cm above Ground Plane
1.5 Meters
FCC Part 15.225
Page 7 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
SUMMARY OF TEST RESULTS
FCC Rules
Description of Test
Result
§15.203
Antenna Requirement
Compliance
§15.207
AC Line Conducted Emission
Compliance
§15.225
§15.209 §15.205
Radiated Emission Test
Compliance
§15.225(e)
Frequency Stability
Compliance
§15.215(c)
20dB Emission Bandwidth
Compliance
FCC Part 15.225
Page 8 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
TEST EQUIPMENT LIST
Manufacturer
Description
Serial
Number
Model
Calibration
Date
Calibration
Due Date
Conducted Emissions Test
Rohde & Schwarz
EMI Test Receiver
ESCS30
2018-07-11
2019-07-11
2017-12-21
2018-12-21
ESH3Z2
100176
3560.6650.12101613-Yb
DE25985
Rohde & Schwarz
LISN
ENV216
Rohde & Schwarz
Transient Limiter
2018-05-21
2018-11-21
Rohde & Schwarz
CE Test software
EMC 32
V8.53.0
NCR
NCR
Conducted Emission
Cable
UF A210B-10720-504504
2018-05-12
2018-11-12
Radiated Emission Test
HP
Amplifier
HP8447E
1937A01046
2018-05-17
2018-11-19
Rohde & Schwarz
EMI Test Receiver
ESCI
101120
2018-08-01
2019-02-01
Sunol Sciences
Broadband Antenna
JB1
A040904-1
2017-12-22
2020-12-21
ETS
Passive Loop Antenna
6512
00029604
2018-03-07
2021-03-06
Sonoma instrument
Amplifier
310N
186238
2018-05-12
2018-11-12
RF Cable
UFA147A2362-100100
MFR64639
231029-003
2018-08-01
2019-02-01
RF Cable
104PEA
218124002
2018-05-21
2018-11-19
Fluke
Digital Multimeter
287
19000011
2018-04-12
2019-04-12
Long Wei
DC Power Supply
TPR-6420D
398363
NCR
NCR
ESPEC
Temperature &
Humidity Chamber
EL-10KA
9107726
2017-12-21
2018-12-21
Ducommun
technologies
Ducommun
technologies
* Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have
been performed in accordance to requirements that traceable to National Primary Standards and International System
of Units (SI).
FCC Part 15.225
Page 9 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
FCC§15.203 - ANTENNA REQUIREMENT
Applicable Standard
An intentional radiator shall be designed to ensure that no antenna other than that furnished by the
responsible party shall be used with the device. The use of a permanently attached antenna or of an
antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with
the provisions of this section.
Antenna Connected Construction
The EUT has an internal antenna arrangement, which was permanently attached, the antenna gain is -15
dBi, fulfill the requirement of this section. Please refer to EUT photos for details.
FCC Part 15.225
Page 10 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
FCC §15.207 – AC LINE CONDUCTED EMISSION
Applicable Standard
FCC§15.207
EUT Setup
The setup of EUT is according with per ANSI C63.10-2013 measurement procedure. The specification
used was with the FCC Part 15.207.
The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the
middle.
The spacing between the peripherals was 10 cm.
EMI Test Receiver Setup
The EMI test receiver was set to investigate the spectrum from 150 kHz to 30 MHz.
During the conducted emission test, the EMI test receiver was set with the following configurations:
FCC Part 15.225
Frequency Range
IF B/W
150 kHz – 30 MHz
9 kHz
Page 11 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
Test Procedure
During the conducted emission test, the adapter was connected to the outlet of the LISN.
Maximizing procedure was performed on the six (6) highest emissions of the EUT.
All final data was recorded in the Quasi-peak and average detection mode.
Corrected Factor & Margin Calculation
The Corrected factor is calculated by adding LISN VDF (Voltage Division Factor), Cable Loss and
Transient Limiter Attenuation. The basic equation is as follows:
Correction Factor = LISN VDF + Cable Loss + Transient Limiter Attenuation
The “Margin” column of the following data tables indicates the degree of compliance with the applicable
limit. For example, a margin of 7 dB means the emission is 7 dB below the limit. The equation for margin
calculation is as follows:
Margin = Limit – Corrected Amplitude
Test Results Summary
According to the recorded data in following table, the EUT complied with the FCC Part 15.207.
Refer to CISPR16-4-2:2011 and CISPR 16-4-1:2009, the measured level complies with the limit if
Lm + U(Lm) ≤ Llim + Ucispr
In BACL, U(Lm) is less than Ucispr, if Lm is less than Llim, it implies that the EUT complies with the limit.
Test Data
Environmental Conditions
Temperature:
26 ℃
Relative Humidity:
56 %
ATM Pressure:
101.0 kPa
The testing was performed by Shawn Xiao on 2018-10-13.
FCC Part 15.225
Page 12 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
Adapter power supply:
EUT operation mode: Transmitting
AC 120 V/60 Hz, Line:
90
80
70
QP
Level in dBμ
60
AV
50
40
30
20
10
150k
300 400 500
800 1M
2M
3M 4M 5M 6
8 10M
20M
30M
Frequency in Hz
Frequency
(MHz)
Corrected
Amplitude
(dBμV)
Correction
Factor
(dB)
Limit
(dBμV)
Margin
(dB)
Detector
(PK/Ave./QP)
0.150000
48.4
19.8
66.0
17.6
QP
0.181500
41.4
19.8
64.4
23.0
QP
0.209500
43.3
19.7
63.2
19.9
QP
0.225500
43.2
19.7
62.6
19.4
QP
0.229500
42.7
19.7
62.5
19.8
QP
13.558570
49.9
20.2
60.0
10.1
QP
0.150000
31.8
19.8
56.0
24.2
Ave.
0.181500
28.8
19.8
54.4
25.6
Ave.
0.209500
32.4
19.7
53.2
20.8
Ave.
0.225500
32.4
19.7
52.6
20.2
Ave.
0.229500
32.9
19.7
52.5
19.6
Ave.
13.558570
45.0
20.2
50.0
5.0
Ave.
FCC Part 15.225
Page 13 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
AC 120V/60 Hz, Neutral:
90
80
70
QP
Level in dBμ
60
AV
50
40
30
20
10
150k
300 400 500
800 1M
2M
3M 4M 5M 6
8 10M
20M
30M
Frequency in Hz
Frequency
(MHz)
Corrected
Amplitude
(dBμV)
Correction
Factor
(dB)
Limit
(dBμV)
Margin
(dB)
Detector
(PK/Ave./QP)
0.165500
43.6
19.7
65.2
21.6
QP
0.197500
40.1
19.7
63.7
23.6
QP
0.217500
42.8
19.7
62.9
20.1
QP
0.229500
42.7
19.7
62.5
19.8
QP
0.257500
38.3
19.7
61.5
23.2
QP
13.558570
44.4
20.2
60.0
15.6
QP
0.165500
29.6
19.7
55.2
25.6
Ave.
0.197500
31.3
19.7
53.7
22.4
Ave.
0.217500
34.0
19.7
52.9
18.9
Ave.
0.229500
32.6
19.7
52.5
19.9
Ave.
0.257500
26.9
19.7
51.5
24.6
Ave.
13.558570
40.3
20.2
50.0
9.7
Ave.
FCC Part 15.225
Page 14 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
POE Supply:
AC 120 V/60 Hz, Line:
90
80
70
QP
Level in dBμ
60
AV
50
40
30
20
10
150k
300 400 500
800 1M
2M
3M 4M 5M 6
8 10M
20M
30M
Frequency in Hz
Frequency
(MHz)
Corrected
Amplitude
(dBμV)
Correction
Factor
(dB)
Limit
(dBμV)
Margin
(dB)
Detector
(PK/Ave./QP)
0.161500
41.0
19.8
65.4
24.4
QP
0.201500
35.4
19.7
63.5
28.1
QP
0.241500
31.1
19.7
62.0
30.9
QP
0.301500
37.3
19.8
60.2
22.9
QP
0.347130
43.7
19.7
59.0
15.3
QP
0.352690
43.0
19.7
58.9
15.9
QP
0.161500
30.1
19.8
55.4
25.3
Ave.
0.201500
23.4
19.7
53.5
30.1
Ave.
0.241500
17.6
19.7
52.0
34.4
Ave.
0.301500
32.5
19.8
50.2
17.7
Ave.
0.347130
37.0
19.7
49.0
12.0
Ave.
0.352690
34.4
19.7
48.9
14.5
Ave.
FCC Part 15.225
Page 15 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
AC 120V/60 Hz, Neutral:
90
80
70
QP
Level in dBμ
60
AV
50
40
30
20
10
150k
300 400 500
800 1M
2M
3M 4M 5M 6
8 10M
20M
30M
Frequency in Hz
Frequency
(MHz)
Corrected
Amplitude
(dBμV)
Correction
Factor
(dB)
Limit
(dBμV)
Margin
(dB)
Detector
(PK/Ave./QP)
0.157500
39.3
19.7
65.6
26.3
QP
0.186500
37.5
19.7
64.2
26.7
QP
0.237500
32.2
19.7
62.2
30.0
QP
0.352750
39.8
19.7
58.9
19.1
QP
0.356630
38.8
19.7
58.8
20.0
QP
0.392090
27.4
19.7
58.0
30.6
QP
0.157500
27.4
19.7
55.6
28.2
Ave.
0.186500
24.1
19.7
54.2
30.1
Ave.
0.237500
18.9
19.7
52.2
33.3
Ave.
0.352750
31.3
19.7
48.9
17.6
Ave.
0.356630
27.8
19.7
48.8
21.0
Ave.
0.392090
12.8
19.7
48.0
35.2
Ave.
Note:
1) Correction Factor =LISN VDF (Voltage Division Factor) + Cable Loss + Transient Limiter Attenuation
2) Corrected Amplitude = Reading + Correction Factor
3) Margin = Limit – Corrected Amplitude
FCC Part 15.225
Page 16 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
FCC§15.225, §15.205 & §15.209 - RADIATED EMISSIONS TEST
Applicable Standard
As per FCC Part 15.225
(a) The field strength of any emissions within the band 13.553–13.567 MHz shall not exceed 15,848
microvolts/meter at 30 meters.
(b) Within the bands 13.410–13.553 MHz and 13.567–13.710 MHz, the field strength of any emissions
shall not exceed 334 microvolts/meter at 30 meters.
(c) Within the bands 13.110–13.410 MHz and 13.710–14.010 MHz the field strength of any emissions
shall not exceed 106 microvolts/meter at 30 meters.
(d) The field strength of any emissions appearing outside of the 13.110–14.010 MHz band shall not exceed
the general radiated emission limits in §15.209.
EUT Setup
Note: Antenna is set up at 1m during test for below 30MHz.
The radiated emission tests were performed in the 3-meter chamber a test site, using the setup accordance
with the ANSI C63.10-2013. The specification used was the FCC Part Subpart C limits.
EMI Test Receiver Setup
According to FCC Rules, 47 CFR 15.33, the EUT emissions were investigated up to 1000 MHz.
During the radiated emission test, the EMI test Receiver was set with the following configurations:
FCC Part 15.225
Page 17 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
Frequency Range
RBW
Video B/W
IF B/W
Detector
9 kHz – 150 kHz
150 kHz –30 MHz
30 MHz – 1000 MHz
300 Hz
10 kHz
100 kHz
1 kHz
30 kHz
300 kHz
QP
QP
QP
Corrected Amplitude & Margin Calculation
The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Loss, and subtracting the
Amplifier Gain from the Meter Reading. The basic equation is as follows:
Corrected Factor = Antenna Factor + Cable Loss- Amplifier Gain
Corrected Amplitude = Meter Reading + Corrected Factor
The “Margin” column of the following data tables indicates the degree of compliance with the applicable
limit. For example, a margin of 7 dB means the emission is 7 dB below the limit. The equation for margin
calculation is as follows:
Margin = Limit – Corrected Amplitude
Test Results Summary
According to the data in the following table, the EUT complied with the FCC §15.209.
Refer to CISPR16-4-2:2011 and CISPR 16-4-1:2009, the measured level is in compliance with the limit if
Lm + U(Lm) ≤ Llim + Ucispr
In BACL, U(Lm) is less than Ucispr, if Lm is less than Llim, it implies that the EUT complies with the limit.
Test Data
Environmental Conditions
Temperature:
26 ℃
Relative Humidity:
56 %
ATM Pressure:
101.0 kPa
The testing was performed by Shawn Xiao on 2018-10-01.
Test mode: Transmitting
1) Spurious Emissions (9 kHz~30 MHz):
Indicated
Correction Factor
Maximum Table Antenna
PreAnt. Cable
Freq.
Reading Angle Height Detector
Amp.
Factor Loss
(m)
(MHz)
(dBµV) Degree
Gain
(dB) (dB)
@3m
(dB)
FCC part 15.225
Corrected
Amplitude Limit
(dBµV/m) (dBµV/m) Result
@3m
@3m
0.009
5.98
25
1.0
QP
87.8
0.2
30.2
63.78
128.52
Pass
0.15
27.96
25
1.0
QP
65.7
0.3
30.2
63.76
104.08
Pass
FCC Part 15.225
Page 18 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
9 kHz~150 kHz
150 kHz~30 MHz
Fundamental test
FCC Part 15.225
Page 19 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
2) Spurious Emissions (30 MHz~1GHz):
80
70
60
Level in dB¦ÌV/
Electric Field Strength QP-3m
50
40
30
20
10
30M
50
60
80
100M
200
300
400
500
800
1G
Frequency in Hz
40.679625
Corrected
Amplitude
(dBμV/m)
27.54
Antenna
height
(cm)
108.0
Turntable
position
(degree)
99.0
Correction
Factor
(dB/m)
-14.2
262.490375
30.70
108.0
46.0
299.983750
32.62
108.0
488.150750
31.10
163.0
836.829500
29.23
922.116250
40.88
Frequency
(MHz)
Antenna
Polarity
Limit
(dBμV/m)
Margin
(dB)
40.00
12.46
-13.2
46.00
15.30
243.0
-10.6
46.00
13.38
23.0
-7.4
46.00
14.90
308.0
333.0
5.6
46.00
16.77
217.0
345.0
6.7
46.00
5.12
Note:
1) Correction Factor =Antenna factor(Rx) + Cable Loss – Amplifier factor
2) Corrected Amplitude = Reading + Correction Factor
3) Margin = Limit – Corrected Amplitude
FCC Part 15.225
Page 20 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
3) Inband:
Indicated
Frequency
Range
(MHz)
13.11013.410
13.41013.553
13.55313.567
13.56713.710
13.71014.010
Mark
Point
(MHz)
Correction Factor
FCC part 15.225
Corrected
Maximum Table Antenna
Pre- Amplitude Limit
Ant. Cable
Reading Angle Height Detector
Amp. (dBµV/m)
Factor
Loss
(dBµV/m) Result
(m)
(dBµV) Degree
Gain
@3m
(dB) (dB)
@3m
@3m
(dB)
13.398
69.19
1.2
QP
32.0
0.2
30.2
71.19
80.5
Pass
13.545
71.83
1.3
QP
32.0
0.2
30.2
73.83
90.5
Pass
13.557
71.26
QP
32.0
0.2
30.2
73.26
124
Pass
13.564
70.34
1.2
QP
32.0
0.2
30.2
72.34
90.5
Pass
13.879
68.64
1.1
QP
32.0
0.2
30.2
70.64
80.5
Pass
FCC Part 15.225
Page 21 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
FCC§15.225(e) - FREQUENCY STABILITY
Applicable Standard
The frequency tolerance of the carrier signal shall be maintained within ±0.01% of the operating frequency
over a temperature variation of −20 degrees to +50 degrees C at normal supply voltage, and for a variation
in the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees
C. For battery operated equipment, the equipment tests shall be performed using a new battery.
Test Procedure
Frequency Stability vs. Temperature: The equipment under test was connected to PC, then to an external
AC power supply and inductive antenna was connected to a Spectrum Analyzer. The EUT was placed
inside the temperature chamber.
After the temperature stabilized for approximately 20 minutes, the frequency output was recorded from the
Spectrum Analyzer.
Frequency Stability vs. Voltage: An external variable AC power supply Source. The voltage was set to
115% of the nominal value and was then decreased until the transmitter light no longer illuminated; i.e.,
the end point. The output frequency was recorded for each voltage.
Test Data
Environmental Conditions
Temperature:
26 ℃
Relative Humidity:
56 %
ATM Pressure:
101.0 kPa
The testing was performed by Shawn Xiao on 2018-10-13.
Test Mode: Transmitting
Test Result: Pass
Voltage Supply
(VDC)
9.5V
8.6 V
10.4 V
FCC Part 15.225
Temperature
(℃)
Measured
Frequency
(MHz)
Frequency
Error
(%)
Part 15.225
Limit
-20
-10
10
20
30
40
50
20
20
13.560224
13.560327
13.560420
13.560506
13.560520
13.560606
13.560701
13.560572
13.560451
13.560598
0.00165%
0.00241%
0.00310%
0.00373%
0.00383%
0.00447%
0.00517%
0.00422%
0.00333%
0.00441%
±0.01%
±0.01%
±0.01%
±0.01%
±0.01%
±0.01%
±0.01%
±0.01%
±0.01%
±0.01%
Page 22 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
FCC§15.215(c) - 20dB EMISSION BANDWIDTH
Requirement
Per 15.215 (c) Intentional radiators operating under the alternative provisions to the general emission
limits, as contained in §§ 15.217 through 15.257 and in Subpart E of this part, must be designed to ensure
that the 20 dB bandwidth of the emission, or whatever bandwidth may otherwise be specified in the
specific rule section under which the equipment operates, is contained within the frequency band
designated in the rule section under which the equipment is operated. The requirement to contain the
designated bandwidth of the emission within the specified frequency band includes the effects from
frequency sweeping, frequency hopping and other modulation techniques that may be employed as well as
the frequency stability of the transmitter over expected variations in temperature and supply voltage. If a
frequency stability is not specified in the regulations, it is recommended that the fundamental emission be
kept within at least the central 80% of the permitted band in order to minimize the possibility of out-ofband operation.
Test Procedure
1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal
from an external generator.
2. Position the EUT on the table of the chamber, Turn on the EUT. Then set it to any one convenient
frequency within its operating range. Set a reference level on the measuring instrument equal to the
highest peak value.
3. Measure the frequency difference of two frequencies that were attenuated 20 dB from the reference
level. Record the frequency difference as the emission bandwidth.
Test Data
Environmental Conditions
Temperature:
26 ℃
Relative Humidity:
56 %
ATM Pressure:
101.0 kPa
The testing was performed by Shawn Xiao on 2018-10-01.
Test Mode: Transmitting
FCC Part 15.225
Page 23 of 24
Bay Area Compliance Laboratories Corp. (Shenzhen)
Report No.: RSZ180809001-00D
Test Result: Pass
20 dB Emission Bandwidth
***** END OF REPORT *****
FCC Part 15.225
Page 24 of 24
Download: AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Mirror Download [FCC.gov]AMP6700 AMP 6700 Test Report  Advanced Mobile Payment Inc.
Document ID4058932
Application IDV9bQQqOnaf4XeS3ZsftYtQ==
Document DescriptionTest Report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize33.73kB (421613 bits)
Date Submitted2018-11-02 00:00:00
Date Available2018-11-02 00:00:00
Creation Date2018-11-02 21:48:29
Producing SoftwareAcrobat Distiller 9.0.0 (Windows)
Document Lastmod2018-11-02 21:48:29
Document TitleTest Report
Document CreatorPScript5.dll Version 5.2.2
Document Author: SZ141

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : SZ141
Create Date                     : 2018:11:02 21:48:29+08:00
Modify Date                     : 2018:11:02 21:48:29+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : SZ141
Title                           : Microsoft Word - RSZ180809001-00D  FCC Part 15.225 NFC report---已看--11-02 updated.doc
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:56528cb1-be3b-481f-9aeb-052c4ba75c47
Instance ID                     : uuid:685a8df4-d37a-4321-a430-7653e3043e8a
Page Count                      : 24