FCC ID 2AKLL-FOCUS89
3D Printer
by Zhejiang Flashforge 3D Technology CO., Ltd.
Grantee Code: 2AKLL Product Code: FOCUS89
Latest application date: 2021-08-05
FCC ID Device Details
Operating Frequencies
| Frequency Range | Application Purpose | Final Action Date |
|---|---|---|
| 2412-2462 MHz | Original Equipment | 2021-08-05 |
Exhibits
| Document | Type | Available | File |
|---|---|---|---|
| User Manual | Users Manual | 2021-08-05 | PDF 2.1 MB |
| Internal Photos | Internal Photos | 2021-08-05 | PDF 1.1 MB |
| External Photos | External Photos | 2021-08-05 | PDF 417.4 KB |
| Label | ID Label/Location Info | 2021-08-05 | PDF 72.7 KB |
| Test Setup Photos | Test Setup Photos | 2021-08-05 | PDF 299.1 KB |
| Test Report | Test Report | 2021-08-05 | PDF 3.3 MB |
| Agent Authorization Rev 1.0 | Cover Letter(s) | 2021-08-05 | PDF 20.3 KB |
| FCC Short & Long Term Confidentiality Request Rev4.1 | Cover Letter(s) | 2021-08-05 | PDF 70.3 KB |
| RF Exposure | RF Exposure Info | 2021-08-05 | PDF 337.9 KB |
| Block diagram Metadata only | Block Diagram | PDF 288.6 KB | |
| Schematic Metadata only | Schematics | PDF 607.3 KB | |
| op Metadata only | Operational Description | PDF 6 KB |
Application Information
| Application ID | N0A/Zi255wCtDJPom/eZBQ== |
|---|---|
| Final Action Date | 2021-08-05 |
| Application Purpose | Original Equipment |
| Applicant FRN | 0026099036 |
| Model | FOCUS89 |
| Frequency Range | 2412-2462 MHz |
| Equipment Class | DTS - Digital Transmission System |
| Device Description | 3D Printer |
| Responsible Party | Qian Wang, Machinists Helper, wq@sz3dp.com  , 0571-89774128 |
| Technical Contact | Zhejiang Flashforge 3D Technology Co., Ltd., wq@sz3dp.com |
| Test Firm | Gavin Liang, Shenzhen LCS Compliance Testing Laboratory Ltd., gavin.liang@lcs-cert.com  , 0755-82591330 |
| TCB Email | certification@micomlabs.com  |
| TCB Scope | A4: UNII devices & low power transmitters using spread spectrum techniques |
| Short-Term Confidentiality | No |
| Long-Term Confidentiality | Yes |
| Grant Deferral | No |
| Modular Equipment | Does not apply |
| Composite Device | No |
| Composite Part | No |
| Cognitive Radio | No |
| Authorization Waiver | No |
| Authorization Waiver Approved | No |
| Section 5301 Certification | Yes |
| Related OET Knowledge DataBase Inquiry | No |
| Grant Comments | Power listed is the maximum conducted output power. This device contains 20 and 40 MHz signal bandwidth. The antennas used with this transmitter must be installed to provide a minimum separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi- transmitter product procedures. End-users must be provided with operating procedures for satisfying RF exposure compliance. |
Applications
| Application ID | Date | Purpose |
|---|---|---|
| N0A/Zi255wCtDJPom/eZBQ== | 2021-08-05 | Original Equipment |
Equipment Authorization
| Frequency | Output | Rules |
|---|---|---|
| 2412-2462 MHz | 0.0496000 | 15C |
Grants
TCB Grant - Application N0A/Zi255wCtDJPom/eZBQ==
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
MiCOM Labs 575 Boulder Court Pleasanton, CA 94566 |
Date of Grant: 08/05/2021 Application Dated: 08/05/2021 |
| Zhejiang Flashforge 3D Technology CO., Ltd. |
| No. 518, Xianyuan Road, |
| Jinhua, Zhejiang, China |
| Attention: Qian Wang , Machinists Helper |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | 2AKLL-FOCUS89 |
| Name of Grantee: | Zhejiang Flashforge 3D Technology CO., Ltd. |
| Equipment Class: | Digital Transmission System |
| Notes: | 3D Printer |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 2412.0 - 2462.0 | 0.0496 |
| Power listed is the maximum conducted output power. This device contains 20 and 40 MHz signal bandwidth. The antennas used with this transmitter must be installed to provide a minimum separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi- transmitter product procedures. End-users must be provided with operating procedures for satisfying RF exposure compliance. |
EAS Grant - Application N0A/Zi255wCtDJPom/eZBQ==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
Zhejiang Flashforge 3D Technology CO., Ltd. No. 518, Xianyuan Road, Jinhua, Zhejiang, China |
Date of Grant: 08/05/2021 Application Dated: 08/05/2021 |
| Attention: Qian Wang , Machinists Helper |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | 2AKLL-FOCUS89 |
| Name of Grantee: | Zhejiang Flashforge 3D Technology CO., Ltd. |
| Equipment Class: | Digital Transmission System |
| Notes: | 3D Printer |
| Modular Type: | Does not apply |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 2412.0 - 2462.0 | 0.0496 |
| Power listed is the maximum conducted output power. This device contains 20 and 40 MHz signal bandwidth. The antennas used with this transmitter must be installed to provide a minimum separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi- transmitter product procedures. End-users must be provided with operating procedures for satisfying RF exposure compliance. |
| Mail To: |