HELICUTE Flying Saucer Series User Manual Shantou Helicute Model Aircraft Industrial Co.,Ltd

Shantou Helicute Model Aircraft Industrial Co.,Ltd Flying Saucer Series

Page 1 of HELICUTE Flying Saucer Series User Manual  Shantou Helicute Model Aircraft Industrial Co.,Ltd

USED FOR H816, H8160, H816W
@licfi®
WAVE RAZOR
HIGH PERFORMANCE UFO FOR RC ENTHUSIASTS
FLIGHT MANUAL
Battery requirements for tranmitter:
A x 1.5V AAA size batteries (not included)
DRONE is equipped with a Li-Poly rechargeable battery,
please also pay attention to the following safety precautions:
" Don’t use or leave the battery near a heat source such as fire or heater.
‘ Don‘t strike or throw the battery against any hard surface,
‘ Don‘t immerse the battery in water, and keep the battery in a cool dry place.
‘ When recharging, only use the battery charger intended for that purpose
‘ Don‘t over-charge the battery
* Don‘t directly solder the battery or pierce it with a nail or other sharp object,
‘ Don‘t transport or store the battery together with metal objects,
‘ Never charge the battery for more than one hour
‘ Never leave charging battery unattended. NOte: —
' Always dispose of old batteries responsibly
Safely Precautions
- Please read through the manuals before using.
- Please store small parts in a place well out of the reach of small children.
- Never leave the DRONE unattended during battery charging.
- Neverthrow any batteries in a fire.
. Neverfly the DRONE near other people.
. Keep all body parts away from the copter while the rotor blades are spinning.
. Nevertry to repair circuitry, there are no serviceable electronic inside the
DRONE or transmitter.
.1.
Flying Precau ions
1.Keep small parts out of the reach of children, to avoid choking hazard.
2,The DRONE is powerful, when taking off, move the throttle stick foreard gradually, to
avoid it's rising too fast.
3, After flight, turn off the DRONE first, then turn off the controller.
4.Do not put the battery in high temperature or near heat source
5.Note, to avoid injury or damage, the DRONE should not beflown nearer than 2 meters
/7 feet from people or other obstacles.
6,Children should fly the DRONE under adult supervision only, Always keep the DRONE
inclear sight while flying,
7,Always turn off the power of the controller and DRONE when not in use,
Battery Protection
1.The DRONE is equipped with low-voltage protection: When it's battery is low, the programmed
control system will stop electrical supply to DRONE 's rotors. The battery then needs charging
to allow the DRONE to fly again.
Maintenance
1. Clean the DRONE with clean, dry soft cloth only.
2. To avoid irreparable damage, keep the DRONE dry and away from water. Do not fly in
rainy conditions.
3, Check the DRONE and accessories for damage. If damage is found, do not use the
DRONE until it is repaired,
Battery Installa &
Controller
Battery cover
4 X 1.5V AAA
batteries
1. To install batteries: Open the cover of battery case, insert 4 X 1.5V AAA batteries,
according to indicated polarity (batteries not included).
Battery installation should be done under adult supervision onlyl
Do not mix old and new batteries.
Do not mix different types of batteries.
1,|nsert one side of the USB connector into the drone/battery. and the other side into any
computer USB port.
How to get the batte
One hand press the frame as picture shows,
and another hand press the battery to get it out.
Controller
Press one time to unlock lhc drone
press again ior sio,~.iy landing
Press for 3 seconds to emergency stop
Camera light
The light will flash while taking picture
abd reniind on nhiic recording video
Power light
Take picture/record video
Press one time ror taking picture,
press for 3 seconds for recording video
Speed Select a
Press down once to changc
speed [Listen to beepsi
Slow speed . one beep
Medium speed . t/vo beeps
High speed . three peeps
Throttle (Left Stick
Flip
Press down once ione beep
sounds. and then coniroi ruddci
to perform flip function
Right Stick/Rudder
Trim button
Trim button
Trim button
One key return function Headless mode
Piess once inio headless modc
press again to quit headless iunction
Replacing Damaged blades:
Vour set will come with 4
replacement rotors, two (A) type
and two (B) type, You will see
the "A" and “B“ word on the canopy,
put the rotor on the motor accordingly, 5 A
pera lng steps
3. Turn on the DRONE
(The LED light on the
drone flashes rapidly)
1.Put the throttle lever down. 2. Turn on the controller
4. Place the DRONE at a 5, Push the throttle lever up and 6.After the DRONE connect
level position. down, a beep will sound. The to the controller, press this
controller connects to the button for start flying. and
DRONE press again if you want to
(The LED light on the drone stop the DRONE.
remains on).The DRONE
is ready to fly.
pera ol
Up and down Forward and Backward
[C Backward
if siege
‘- ., Forward ‘
Ubrop
Left Spin and Right Spin
Left Spin Right Spin
Leftside and Rightside
<2 Lehside fly Rightside ily-p
Note: When the drone is flying towards you, the control directions are reversed,
.4.
T fine tuning
_Forward/backward
fine»tuning
Left/right spin
fine tuning Leftside/rightside
fine tuning
Rightspin
Trim .4 7 , 3. K _
/ Right Spin i
' trimmer
Ra
at F lps & Rolls
You can perform flips with your DRONE in any of the speed settings.
Press down the rudder once(one beep sounds) then push the rudder in related direction.
Left flip Rightflip
~._ /
Press down the rudder once and then
push the rudder to right
Backward flip
Press down the rudder once and then
push the rudder to left
Forward flip
Press down the rudder once and then
push the rudder to backward
Press down the rudder once and then
push the rudder to forward
Before you perform a Flip Trick, always make sure you have enough
space both above and below your DRONE .
Auto trim function
Press the throttle and rudder down
to 45 degree circle (as above) for
10 second, you Will see the light on
the PC board of drone flashing rapidly,
then pls let go the throttle and rudder.
the light on the PC board remains on,
the auto trim finishes.
One key return function
When the drone is taking off, the LED light
on the drone stop flashing, at the moment,
the drone sets its front side to be the front
direction for one key return flying.|f you want
to reset the front direction, then you need to
turn off the rc drone and reset it again.
Press the button as picture shows for
one key back home function, and then
control right sticker (Rudder) to every
direction to quit this function.
Control the rudder
to quit this function
.5. (every direction)
Press this button
Headless func I
HOW TO GET INTO/QUIT HEADLESS FUNCTION FLYING?
Press the button on controller(as picture shows) you Will hear
beep sounds then you get into compass mode flyingTo quit from
compass mode,iust press it again and you Will hear beep sound
disappears,
5.:
EMS
SIDE" UNDER HEADLESS FUNCTION? "
When the drone is taking off, the LED light
on the drone stop flashing, at the moment,
, x
i l Right
I f
the drone sets its front side to be the front ‘ (
direction for headless mode flying. Bacfiard
HOW TO RECOGNIZE THE " FORWARD © Forward
Left
vi
If you Want to reset the front direction, then you
need to turn off the rc drone and reset it again.
Camera.
Normal camera:
720P camera (Resolution: 1280720)
HOW TO REVIEWING PHOTOSNIDEOS
insert the TF card into rc drone Before reviewing photos and videos, please insert
one end of DATA CABLE onto port of cameia
correctlythe other end onto computeropen
"my computer'and you will find related file from which
you can view photos and videos you took,
Wifi camera:
1.0m pixel WIFI camera (720Pl1280*720)
1.SOFTWARE DOWNLOAD AND INSTALLATION
APP (IDS) APK (Androidl Oversea) APK (Androidl Mainland China)
2.USING INSTRUCTION
1). Connect the model to the power.
2). Enter the “setting" menu of your mobile device and turn on WIFI,
3). Find a network WIFI called “HELICUTE 12th FPV" ,click connection until “connected".
4). Open the “HELICUTE 72th FPV“ software, click the “play" icon into the control
interface.And you Will see the real time VldEO.
at" . tart-amalgam”
,.
(s
~W“ .
kl/
720PFPV , a. i
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
This device complies With Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply With the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 200m between the radiator and
your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Download: HELICUTE Flying Saucer Series User Manual  Shantou Helicute Model Aircraft Industrial Co.,Ltd
Mirror Download [FCC.gov]HELICUTE Flying Saucer Series User Manual  Shantou Helicute Model Aircraft Industrial Co.,Ltd
Document ID3333474
Application IDWZIJTO4V7Ekz8wJtbm7Fug==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize383.77kB (4797069 bits)
Date Submitted2017-03-27 00:00:00
Date Available2017-03-27 00:00:00
Creation Date2017-02-22 10:15:40
Producing SoftwareAdobe Acrobat 11.0 Image Conversion Plug-in
Document Lastmod2017-02-22 10:16:29
Document TitleUser Manual
Document CreatorAdobe Acrobat 11.0

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2017:02:22 10:15:40+08:00
Creator                         : Adobe Acrobat 11.0
Modify Date                     : 2017:02:22 10:16:29+08:00
Title                           : 
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2017:02:22 10:16:29+08:00
Creator Tool                    : Adobe Acrobat 11.0
Format                          : application/pdf
Document ID                     : uuid:d7df94cf-1531-4cb4-8b56-d8239b5eb4d3
Instance ID                     : uuid:c2f6872e-42d0-4d87-a417-80580ed033a6
Producer                        : Adobe Acrobat 11.0 Image Conversion Plug-in
Page Count                      : 1