A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.

IHR FAC INC. BbSPEAKER

Page 1 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 2 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 3 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 4 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 5 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 6 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 7 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 8 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 9 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 10 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 11 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 12 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 13 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 14 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 15 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 16 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 17 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 18 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 19 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 20 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 21 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 22 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 23 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 24 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 25 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 26 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 27 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 28 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 29 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 30 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 31 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 32 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 33 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 34 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 35 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 36 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 37 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 38 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 39 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 40 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 41 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 42 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 43 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 44 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 45 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 46 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 47 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 48 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 49 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 50 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 51 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 52 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 53 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 54 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 55 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 56 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 57 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Page 58 of A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.

FCC Radio Test Report
FCC ID: 2ALMN-A01SPK
This report concerns (check one):
Original Grant
Class I Change
Class II Change
Project No.
Equipment
Test Model
Series Model
Applicant
Address
1711095
BbSPEAKER
A01SPK
N/A
IHR FAC INC.
2F, NO.455, Sec. 2, Zhongqing Rd., Beitun Dist.,
Taichung City 406, Taiwan (R.O.C)
Date of Receipt
Date of Test
Issued Date
Tested by
Nov. 22, 2017
Nov. 22, 2017 ~ Feb. 13, 2018
Feb. 14, 2018
BTL Inc.
Testing Engineer
(Kenji Lin)
Technical Manager
(James Chiu)
Authorized Signatory
(Andy Chiu)
BTL
INC.
No.18, Ln. 171, Sec. 2, Jiuzong Rd.,
Neihu Dist., Taipei City, Taiwan (R.O.C.)
TEL:+886-2-2657-3299 FAX: +886-2-2657-3331
Report No.: BTL-FCCP-2-1711095
Page 1 of 62
Declaration
BTL represents to the client that testing is done in accordance with standard procedures as applicable and
that test instruments used has been calibrated with standards traceable to international standard(s) and/or
national standard(s).
BTL's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility
to ensure that additional production units of this model are manufactured with the identical electrical and
mechanical components. BTL shall have no liability for any declarations, inferences or generalizations
drawn by the client or others from BTL issued reports.
BTL’s report must not be used by the client to claim product certification, approval, or endorsement by
NVLAP, NIST, or any agency of the Federal Government.
This report is the confidential property of the client. As a mutual protection to the clients, the public and
BTL-self, extracts from the test report shall not be reproduced except in full with BTL’s authorized written
approval.
BTL’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements,
and accredited by the conformity assessment authorities listed in this test report.
Limitation
For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this
test report is (are) included in the conformity assessment authorities acceptance respective.
Report No.: BTL-FCCP-2-1711095
Page 2 of 62
Table of Contents
Page
1 . CERTIFICATION
2 . SUMMARY OF TEST RESULTS
2.1 TEST FACILITY
2.2 MEASUREMENT UNCERTAINTY
3 . GENERAL INFORMATION
10
3.1 GENERAL DESCRIPTION OF EUT
10
3.2 DESCRIPTION OF TEST MODES
12
3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING
12
3.4 DUTY CYCLE
13
3.5 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 14
3.6 DESCRIPTION OF SUPPORT UNITS
4 . EMC EMISSION TEST
14
15
4.1 CONDUCTED EMISSION MEASUREMENT
4.1.1 POWER LINE CONDUCTED EMISSION LIMITS
4.1.2 TEST PROCEDURE
4.1.3 DEVIATION FROM TEST STANDARD
4.1.4 TEST SETUP
4.1.5 EUT OPERATING CONDITIONS
4.1.6 EUT TEST CONDITIONS
4.1.7 TEST RESULTS
15
15
15
15
16
16
16
16
4.2 RADIATED EMISSION MEASUREMENT
4.2.1 RADIATED EMISSION LIMITS
4.2.2 TEST PROCEDURE
4.2.3 DEVIATION FROM TEST STANDARD
4.2.4 TEST SETUP
4.2.5 EUT OPERATING CONDITIONS
4.2.6 EUT TEST CONDITIONS
4.2.7TEST RESULTS (9KHZ TO 30MHZ)
4.2.7TEST RESULTS (30MHZ TO 1000 MHZ)
4.2.7TEST RESULTS (ABOVE 1000 MHZ)
17
17
18
18
19
20
20
20
20
20
5 . BANDWIDTH TEST
5.1 APPLIED PROCEDURES / LIMIT
5.1.1 TEST PROCEDURE
5.1.2 DEVIATION FROM STANDARD
5.1.3 TEST SETUP
5.1.4 EUT OPERATION CONDITIONS
5.1.5 EUT TEST CONDITIONS
Report No.: BTL-FCCP-2-1711095
21
21
21
21
21
21
21
Page 3 of 62
Table of Contents
5.1.6 TEST RESULTS
6 . MAXIMUM OUTPUT POWER TEST
6.1 APPLIED PROCEDURES / LIMIT
6.1.1 TEST PROCEDURE
6.1.2 DEVIATION FROM STANDARD
6.1.3 TEST SETUP
6.1.4 EUT OPERATION CONDITIONS
6.1.5 EUT TEST CONDITIONS
6.1.6 TEST RESULTS
7 . ANTENNA CONDUCTED SPURIOUS EMISSION
7.1 APPLIED PROCEDURES / LIMIT
7.1.1 TEST PROCEDURE
7.1.2 DEVIATION FROM STANDARD
7.1.3 TEST SETUP
7.1.4 EUT OPERATION CONDITIONS
7.1.5 EUT OPERATION CONDITIONS
7.1.6 TEST RESULTS
8 . POWER SPECTRAL DENSITY TEST
8.1 APPLIED PROCEDURES / LIMIT
8.1.1 TEST PROCEDURE
8.1.2 DEVIATION FROM STANDARD
8.1.3 TEST SETUP
8.1.4 EUT OPERATION CONDITIONS
8.1.5 EUT TEST CONDITIONS
8.1.6 TEST RESULTS
Page
21
22
22
22
22
22
22
22
22
23
23
23
23
23
23
23
23
24
24
24
24
24
24
24
24
9 . MEASUREMENT INSTRUMENTS LIST
25
10 . EUT TEST PHOTO
27
APPENDIX A - CONDUCTED EMISSION
31
APPENDIX B - RADIATED EMISSION (9KHZ TO 30MHZ)
34
APPENDIX C - RADIATED EMISSION (30MHZ TO 1000MHZ)
39
APPENDIX D - RADIATED EMISSION (ABOVE 1000MHZ)
42
APPENDIX E - BANDWIDTH
55
APPENDIX F - MAXIMUM OUTPUT POWER TEST
57
APPENDIX G - ANTENNA CONDUCTED SPURIOUS EMISSION
59
APPENDIX H - POWER SPECTRAL DENSITY TEST
61
Report No.: BTL-FCCP-2-1711095
Page 4 of 62
REPORT ISSUED HISTORY
Issued No.
BTL-FCCP-2-1711095
Report No.: BTL-FCCP-2-1711095
Description
Original Issue.
Issued Date
Feb. 14, 2018
Page 5 of 62
1. CERTIFICATION
Equipment
Brand Name :
Test Model :
Series Model :
Applicant
Manufacturer :
Address
BbSPEAKER
Bb TALKIN’
A01SPK
N/A
IHR FAC INC.
IHR FAC INC.
2F, NO.455, Sec. 2, Zhongqing Rd., Beitun Dist., Taichung City 406, Taiwan
(R.O.C)
Date of Test : Nov. 22, 2017 ~ Feb. 13, 2018
Test Sample : Engineering Sample
Standard(s) : FCC Part15, Subpart C (15.247)
ANSI C63.10-2013
The above equipment has been tested and found in compliance with the requirement of the
relative standards by BTL Inc.
The test data, data evaluation, and equipment configuration contained in our test report (Ref No.
BTL-FCCP-2-1711095) were obtained utilizing the test procedures, test instruments, test sites that
has been accredited by the Authority of TAF according to the ISO-17025 quality assessment
standard and technical standard(s).
Test results included in this report is only for the Bluetooth LE part.
Report No.: BTL-FCCP-2-1711095
Page 6 of 62
2. SUMMARY OF TEST RESULTS
Test procedures according to the technical standard(s):
Applied Standard(s): FCC Part15 (15.247) , Subpart C
Standard(s) Section
Test Item
Judgment
15.207
Conducted Emission
PASS
15.247(d)
Antenna conducted Spurious Emission
PASS
15.247(a)(2)
6dB Bandwidth
PASS
15.247(b)(3)
Peak Output Power
PASS
15.247(e)
Power Spectral Density
PASS
15.203
Antenna Requirement
PASS
15.247(d)/
15.205/
15.209
Transmitter Radiated Emissions
PASS
Remark
NOTE:
(1)” N/A” denotes test is not applicable to this device.
Report No.: BTL-FCCP-2-1711095
Page 7 of 62
2.1 TEST FACILITY
The test facilities used to collect the test data in this report:
Conducted emission Test:
C05: (VCCI RN: C-4742; FCC RN:674415; FCC DN:TW0659)
No. 68-1, Ln. 169, Sec. 2, Datong Rd., Xizhi Dist., New Taipei City 221, Taiwan (R.O.C.)
Radiated emission Test (Below 1 GHz):
CB15: (VCCI RN: G-20020; FCC RN:674415; FCC DN:TW0659; ISED Assigned
Code:20088-5)
No. 68-1, Ln. 169, Sec. 2, Datong Rd., Xizhi Dist., New Taipei City 221, Taiwan (R.O.C.)
Radiated emission Test (Above 1 GHz):
CB15: (VCCI RN: G-20031; FCC RN:674415; FCC DN:TW0659; ISED Assigned
Code:20088-5)
No. 68-1, Ln. 169, Sec. 2, Datong Rd., Xizhi Dist., New Taipei City 221, Taiwan (R.O.C.)
2.2 MEASUREMENT UNCERTAINTY
Where relevant, the following measurement uncertainty levels have been estimated for tests
performed on the EUT as specified in CISPR 16-4-2. The BTL measurement uncertainty is less
than the CISPR 16-4-2 Ucispr requirement.
The reported uncertainty of measurement y ± U, where expanded uncertainty U is based on a
standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of
approximately 95 %.
A. Conducted emission test:
Test Site
Method
Measurement Frequency Range
U,(dB)
C05
CISPR
150 kHz ~ 30MHz
2.68
B. Radiated emission test:
Test Site
Method
CB15
CISPR
(3m)
Test Site
Method
CB15
(3m)
CISPR
Test Site
Method
CB15
(3m)
CISPR
Test Site
CB15
(1m)
Method
CISPR
Report No.: BTL-FCCP-2-1711095
Measurement Frequency Range
9kHz ~ 150kHz
150kHz ~ 30MHz
U,(dB)
2.82
2.58
Measurement Frequency Range
30MHz ~ 200MHz
30MHz ~ 200MHz
200MHz ~ 1,000MHz
200MHz ~ 1,000MHz
Ant. U,(dB)
H V/ V 4.20
3.64
4.56
3.90
Measurement Frequency Range
1GHz ~ 6GHz
1GHz ~ 6GHz
6GHz ~ 18GHz
6GHz ~ 18GHz
Ant.
H V/ V
Measurement Frequency Range
18 ~ 26.5 GHz
26.5 ~ 40 GHz
U,(dB)
4.46
4.40
3.88
4.00
U,(dB)
4.62
5.12
Page 8 of 62
Our calculated Measurement Instrumentation Uncertainty is shown in the tables above.
These are our Ulab values in CISPR 16-4-2 terminology.
Since Table 1 of CISPR 16-4-2 has values of measurement instrumentation uncertainty,
called UCISPR, as follows:
Conducted Disturbance (mains port) – 150 kHz – 30 MHz: 3.6 dB
Radiated Disturbance (electric field strength on an open area test site or alternative
test site) – 30 MHz – 1000 MHz: 5.2 dB
It can be seen that our Ulab values are smaller than UCISPR.
Note: unless specifically mentioned, the uncertainty of measurement has not been taken into
account to declare the compliance or non-compliance to the specification.
Report No.: BTL-FCCP-2-1711095
Page 9 of 62
3. GENERAL INFORMATION
3.1 GENERAL DESCRIPTION OF EUT
Equipment
BbSPEAKER
Brand Name
Bb TALKIN’
Test Model
A01SPK
Series Model
N/A
Model Difference
N/A
Operation Frequency
Output Power (Max.)
Power Source
Power Rating
Modulation Technology
Bit Rate of Transmitter
2402~2480 MHz
GFSK(1Mbps)
Output Power (Max.)
8.46 dBm (1Mbps)
#1 Supplied from USB port.
#2 Supplied from battery.
#1 DC 5V
#2 DC 3.7V
Note:
1. For a more detailed features description, please refer to the manufacturer’s
specifications or the user's manual.
Report No.: BTL-FCCP-2-1711095
Page 10 of 62
2. Channel List:
Frequency
(MHz)
2402
2404
2406
2408
2410
2412
2414
2416
2418
2420
2422
2424
2426
2428
2430
2432
2434
2436
2438
2440
Channel
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
3. Table for Filed Antenna
Ant.
Brand
Master Wave
Test Model
907X00544X0
Report No.: BTL-FCCP-2-1711095
Frequency
(MHz)
2442
2444
2446
2448
2450
2452
2454
2456
2458
2460
2462
2464
2466
2468
2470
2472
2474
2476
2478
2480
Channel
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
Antenna Type
Copper
Antenna
Connector
Gain (dBi)
I-PEX
3.64
Page 11 of 62
3.2 DESCRIPTION OF TEST MODES
To investigate the maximum EMI emission characteristics generates from EUT, the test system
was pre-scanning tested base on the consideration of following EUT operation mode or test
configuration mode which possible have effect on EMI emission level. Each of these EUT
operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively.
Pretest Mode
Description
Mode 1
TX Mode NOTE (1)
The EUT system operated these modes were found to be the worst case during the
pre-scanning test as following:
For Conducted Test
Final Test Mode
Description
Mode 1
TX Mode
For Radiated Test
Final Test Mode
Description
Mode 1
TX Mode NOTE (1)
Note:
(1) The measurements are performed at the high, middle, low available channels.
(2) Orthogonal axis X is found to be the worst case and recorded.
(3)
3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING
During testing channel & power controlling software provided by the customer was used to
control the operating channel as well as the output power level. The RF output power selection
is for the setting of RF output power expected by the customer and is going to be fixed on the
firmware of the final end product power parameters of BT LE
Test Software Version
Blue Test 3
Frequency (MHz)
2402
2440
2480
BT LE
-8
-12
-12
Report No.: BTL-FCCP-2-1711095
Page 12 of 62
3.4 DUTY CYCLE
If duty cycle is ≥ 98 %, duty factor is not required.
If duty cycle is < 98 %, duty factor shall be considered.
Bluetooth
Duty cycle = 0.405 ms / 0.650 ms = 62.31 %
Duty Factor = 10 * log(1 / 0.6231) = 2.05
Note:
For radiated emissions frequency above 1 GHz, the resolution bandwidth of test receiver/spectrum
analyzer is 1 MHz and the video bandwidth is 3 kHz (Duty cycle < 98%).
Report No.: BTL-FCCP-2-1711095
Page 13 of 62
3.5 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED
3.6 DESCRIPTION OF SUPPORT UNITS
The EUT has been tested as an independent unit together with other necessary accessories or
support units. The following support units or accessories were used to form a representative test
configuration during the tests.
Item
Equipment Mfr/Brand
Model/Type No.
FCC ID
Series No.
NB
ASUS
P45VA
N/A
N/A
Fixture
N/A
N/A
N/A
N/A
Item
Shielded Type
Ferrite Core
Length
Note
NO
NO
1.0m
Mini USB Cable
NO
NO
1.5m
Micro USB Cable
Report No.: BTL-FCCP-2-1711095
Page 14 of 62
4. EMC EMISSION TEST
4.1 CONDUCTED EMISSION MEASUREMENT
4.1.1 POWER LINE CONDUCTED EMISSION LIMITS (Frequency Range 150KHz-30MHz)
F equency of Emission (MHz)
Conducted Limit (dBμV)
Quasi-peak
Average
0.15 -0 5
66 to 56*
56 to 46*
0.50 -5.0
56
46
5.0 -30.0
50
Note:
(1) The limit of " * " decreases with the logarithm of the frequency
(2) The test result calculated as following:
Measurement Value = Reading Level + Correct Factor
Correct Factor = Insertion Loss + Cable Loss + Attenuator Factor(if use)
Margin Level = Measurement Value - Limit Value
The following table is the setting of the receiver
Receiver Parameters
Attenuation
Start Frequency
Stop Frequency
IF Bandwidth
Setting
10 dB
0.15 MHz
30 MHz
9 kHz
4.1.2 TEST PROCEDURE
a. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected
to the power mains through a line impedance stabilization network (LISN). All other support
equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling
impedance for the measuring instrument.
b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back
and forth in the center forming a bundle 30 to 40 cm long.
c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the
cable may be terminated, if required, using the correct terminating impedance. The overall
length shall not exceed 1 m.
d. LISN at least 80 cm from nearest part of EUT chassis.
e. For the actual test configuration, please refer to the related Item –EUT Test Photos.
4.1.3 DEVIATION FROM TEST STANDARD
No deviation
Report No.: BTL-FCCP-2-1711095
Page 15 of 62
4.1.4 TEST SETUP
Vertical Reference Ground Plane
40 cm
EUT
Test Receiver
80 cm
LISN
Horizontal Reference Ground Plane
4.1.5 EUT OPERATING CONDITIONS
The EUT was configured for testing in a typical fashion (as a customer would normally use it). The
EUT has been programmed to continuously transmit during test. This operating condition was
tested and used to collect the included data.
4.1.6 EUT TEST CONDITIONS
Temperature: 25°C
Relative Humidity: 55%
Test Voltage: AC 120V/60Hz
4.1.7 TEST RESULTS
Please refer to the Appendix A.
Remark:
(1) All readings are QP Mode value unless otherwise stated AVG in column of『Note』
. If the QP
Mode Measured value compliance with the QP Limits and lower than AVG Limits, the EUT
shall be deemed to meet both QP & AVG Limits and then only QP Mode was measured,
but AVG Mode didn‘t perform.In this case, a “ * ” marked in AVG Mode column of
Interference Voltage Measured.
(2) Measuring frequency range from 150KHz to 30MHz.
(3) “ N/A” denotes test is not applicable to this device.
Report No.: BTL-FCCP-2-1711095
Page 16 of 62
4.2 RADIATED EMISSION MEASUREMENT
4.2.1 RADIATED EMISSION LIMITS
In case the emission fall within the restricted band specified on 15.205(a), then the 15.209(a) limit
in the table below has to be followed.
LIMITS OF RADIATED EMISSION MEASUREMENT (9KHz-1000MHz)
Frequency
Field Strength
Measurement Distance
(MHz)
(microvolts/meter)
(meters)
0.009~0.490
2400/F(KHz)
300
0.490~1.705
24000/F(KHz)
30
1.705~30.0
30
30
30~88
100
88~216
150
216~960
200
960~1000
500
LIMITS OF RADIATED EMISSION MEASUREMENT (Above 1000MHz)
Frequency (MHz)
Above 1000
(dBuV/m) (at 3 meters)
PEAK
AVERAGE
74
54
Notes:
(1) The limit for radiated test was performed according to FCC PART 15C.
(2) The tighter limit applies at the band edges.
(3) Emission level (dBuV/m)=20log Emission level (uV/m).
(4) The test result calculated as following:
Measurement Value = Reading Level + Correct Factor
Correct Factor = Antenna Factor + Cable Loss - Amplifier Gain(if use)
Margin Level = Measurement Value - Limit Value
Report No.: BTL-FCCP-2-1711095
Page 17 of 62
Spectrum Parameter
Setting
Attenuation
Auto
Start Frequency
1000 MHz
Stop Frequency
10th carrier harmonic
RBW / VBW
RBW 1MHz VBW 3MHz peak detector for Pk value
(Emission in restricted band)
RMS detector for AV value
Receiver Parameter
Setting
Attenuation
Auto
Start ~ Stop Frequency
9KHz~90KHz for PK/AVG detector
Start ~ Stop Frequency
90KHz~110KHz for QP detector
Start ~ Stop Frequency
110KHz~490KHz for PK/AVG detector
Start ~ Stop Frequency
490KHz~30MHz for QP detector
Start ~ Stop Frequency
30MHz~1000MHz for QP detector
4.2.2 TEST PROCEDURE
a. The measuring distance of 3 m shall be used for measurements. The EUT was placed on the
top of a rotating table 0.8 meter above the ground at a 3 meter semi-anechoic chamber. The
table was rotated 360 degrees to determine the position of the highest radiation.(below 1GHz)
b. The measuring distance of 3 m shall be used for measurements. The EUT was placed on the
top of a rotating table 1.5 meter above the ground at a 3 meter semi-anechoic chamber. The
table was rotated 360 degrees to determine the position of the highest radiation.(above 1GHz)
c. The height of the equipment or of the substitution antenna shall be 0.8m or 1.5m; the height of
the test antenna shall vary between 1 m to 4 m. Both horizontal and vertical polarizations of
the antenna are set to make the measurement.
d. For each suspected emission, the EUT was arranged to its worst case and then the antenna
was tuned to heights find the maximum reading (used Bore sight function).
e. The receiver system was set to peak and average detect function and specified bandwidth
with maximum hold mode when the test frequency is above 1GHz.
f. The initial step in collecting radiated emission data is a receiver peak detector mode
pre-scanning the measurement frequency range. Significant peaks are then marked and then
Quasi Peak detector mode re-measured.
g. All readings are Peak unless otherwise stated QP in column of Note. Peak denotes that the
Peak reading compliance with the QP Limits and then QP Mode measurement didn‘t perform.
(below 1GHz)
h. All readings are Peak Mode value unless otherwise stated AVG in column of Note. If the Peak
Mode Measured value compliance with the Peak Limits and lower than AVG Limits, the EUT
shall be deemed to meet both Peak & AVG Limits and then only Peak Mode was measured,
but AVG Mode didn‘t perform. (above 1GHz)
i. For the actual test configuration, please refer to the related Item –EUT Test Photos.
4.2.3 DEVIATION FROM TEST STANDARD
No deviation
Report No.: BTL-FCCP-2-1711095
Page 18 of 62
4.2.4 TEST SETUP
(A) Radiated Emission Test Set-Up Frequency Below 1 GHz
Absorbers
1-4 m
3m
EUT
1m
0.8 m
Ground Plane
Receiver
Amp.
(B) Radiated Emission Test Set-Up Frequency Above 1 GHz
Absorbers
1-4 m
3m
EUT
0.7 m
1m
0.8 m
Absorbers
0.3 m
Ground Plane
Receiver
Report No.: BTL-FCCP-2-1711095
Amp.
Page 19 of 62
(C) For radiated emissions below 30MHz
4.2.5 EUT OPERATING CONDITIONS
The EUT was programmed to be in continuously transmitting mode.
4.2.6 EUT TEST CONDITIONS
Temperature: 23°C / 25°C
Relative Humidity: 70% / 45%
Test Voltage: AC 120V/60Hz
4.2.7TEST RESULTS (9KHZ TO 30MHZ)
Please refer to the Appendix B
Remark:
(1) The amplitude of spurious emissions which are attenuated by more than 20 dB below
the permissible value has no need to be reported.
(2) Distance extrapolation factor = 40 log (specific distance / test distance) (dB).
(3) Limit line = specific limits (dBuV) + distance extrapolation factor.
4.2.7TEST RESULTS (30MHZ TO 1000 MHZ)
Please refer to the Appendix C.
4.2.7TEST RESULTS (ABOVE 1000 MHZ)
Please refer to the Appendix D.
Remark:
(1) No limit: This is fundamental signal, the judgment is not applicable.
For fundamental signal judgment was referred to Peak output test.
Report No.: BTL-FCCP-2-1711095
Page 20 of 62
5. BANDWIDTH TEST
5.1 APPLIED PROCEDURES / LIMIT
FCC Part15 (15.247) , Subpart C
Section
Test Item
15.247(a)(2)
Bandwidth
Limit
>= 500KHz
(6dB bandwidth)
Frequency Range
(MHz)
2400-2483.5
Result
PASS
5.1.1 TEST PROCEDURE
a. The EUT was directly connected to the spectrum analyzer and antenna output port as show in
the block diagram below,
b. Spectrum Setting : RBW= 100KHz, VBW=300KHz, Sweep time = 2.5 ms.
5.1.2 DEVIATION FROM STANDARD
No deviation.
5.1.3 TEST SETUP
5.1.4 EUT OPERATION CONDITIONS
The EUT tested system was configured as the statements of 4.1.5 unless otherwise a special
operating condition is specified in the follows during the testing.
5.1.5 EUT TEST CONDITIONS
Test Voltage: AC 120V/60Hz
5.1.6 TEST RESULTS
Please refer to the Appendix E.
Report No.: BTL-FCCP-2-1711095
Page 21 of 62
6. MAXIMUM OUTPUT POWER TEST
6.1 APPLIED PROCEDURES / LIMIT
FCC Part15 (15.247) , Subpart C
Section
Test Item
Limit
15.247(b)(3)
Maximum
Output Power
1 watt or 30dBm
Frequency Range
(MHz)
2400-2483.5
Result
PASS
6.1.1 TEST PROCEDURE
a. The EUT was directly connected to the power meter and antenna output port as show in the
block diagram below,
b. The maximum peak conducted output power was performed in accordance with method 9.1.2
of FCC KDB 558074 D01 DTS Meas Guidance.
6.1.2 DEVIATION FROM STANDARD
No deviation.
6.1.3 TEST SETUP
6.1.4 EUT OPERATION CONDITIONS
The EUT tested system was configured as the statements of 4.1.5 unless otherwise a special
operating condition is specified in the follows during the testing.
6.1.5 EUT TEST CONDITIONS
Test Voltage: AC 120V/60Hz
6.1.6 TEST RESULTS
Please refer to the Appendix F.
Report No.: BTL-FCCP-2-1711095
Page 22 of 62
7. ANTENNA CONDUCTED SPURIOUS EMISSION
7.1 APPLIED PROCEDURES / LIMIT
In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally
modulated device is operating, the RF power that is produced shall be at least 20 dB below that in
the 100 kHz bandwidth within the band that contains the highest level of the desired power, based
on either an RF conducted or a radiated measurement, provided that the transmitter demonstrates
compliance with the peak conducted power limits.
7.1.1 TEST PROCEDURE
a. The EUT was directly connected to the spectrum analyzer and antenna output port as show in
the block diagram below,
b. Spectrum Setting : RBW= 100KHz, VBW=300KHz, Sweep time = 10 ms.
c. Offset=antenna gain+cable loss
7.1.2 DEVIATION FROM STANDARD
No deviation.
7.1.3 TEST SETUP
7.1.4 EUT OPERATION CONDITIONS
The EUT tested system was configured as the statements of 4.1.5 unless otherwise a special
operating condition is specified in the follows during the testing.
7.1.5 EUT OPERATION CONDITIONS
Test Voltage: AC 120V/60Hz
7.1.6 TEST RESULTS
Please refer to the Appendix G.
Report No.: BTL-FCCP-2-1711095
Page 23 of 62
8. POWER SPECTRAL DENSITY TEST
8.1 APPLIED PROCEDURES / LIMIT
FCC Part15 (15.247) , Subpart C
Section
Test Item
Limit
15.247(e)
Power Spectral
Density
8 dBm
(in any 3KHz)
Frequency Range
(MHz)
2400-2483.5
Result
PASS
8.1.1 TEST PROCEDURE
a. The EUT was directly connected to the spectrum analyzer and antenna output port as show in
the block diagram below,
b. Spectrum Setting: RBW=3KHz, VBW=10 KHz, Sweep time = auto.
8.1.2 DEVIATION FROM STANDARD
No deviation.
8.1.3 TEST SETUP
8.1.4 EUT OPERATION CONDITIONS
The EUT tested system was configured as the statements of 4.1.5 unless otherwise a special
operating condition is specified in the follows during the testing.
8.1.5 EUT TEST CONDITIONS
Test Voltage: AC 120V/60Hz
8.1.6 TEST RESULTS
Please refer to the Appendix H.
Report No.: BTL-FCCP-2-1711095
Page 24 of 62
9. MEASUREMENT INSTRUMENTS LIST
Conducted Emission Measurement
Item Kind of Equipment
Manufacturer
Type No.
Serial No.
Calibrated until
TWO-LINE
V-NETWORK
R&S
ENV216
101050
Jan. 24, 2019
Test Cable
TIMES
CFD300-NL
C02
Jun. 14, 2018
EMI Test Receiver
Measurement
Software
R&S
ESR7
EZ_EMC
(Version NB-03A)
101433
Dec. 08, 2018
N/A
N/A
EZ
Radiated Emission Measurement
Item Kind of Equipment
Preamplifier
Manufacturer
EMCI
Type No.
012645B
Serial No.
980267
Preamplifier
EMCI
Test Cable
EMCI
Test Cable
EMCI
Test Cable
EMCI
MXE EMI Receiver
Agilent
Signal Analyzer
Agilent
N9010A
MY52220990
Feb. 22, 2018
Loop Ant
EMCO
6502
42960
Nov. 23, 2018
Horm Ant
SCHWARZBECK
BBHA 9120D
9120D-1342
Feb. 28, 2018
10
Horm Ant
Trilog-Broadband
Antenna
5dB Attenuator
Schwarzbeck
BBHA 9170
187
Dec. 06, 2018
Schwarzbeck
VULB 9168
9168-548
Jan. 15, 2019
EMCI
EMCI-N-6-05
AT-N0623
Jan. 15, 2019
11
12
Report No.: BTL-FCCP-2-1711095
EMC02325
980217
EMC104-SM-S
8m
M-8000
EMC104-SM-S
150207
M-800
EEMC104-SM-S
151205
M-3000
N9038A
MY55420127
Calibrated until
Feb. 28, 2018
Dec. 28, 2018
Jan. 03, 2019
Jan. 03, 2019
Jan. 03, 2019
Jan. 08, 2019
Page 25 of 62
Item Kind of Equipment
1 Spectrum Analyzer
6dB Bandwidth Measurement
Manufacturer
Type No.
Serial No.
R&S
R&S/FSP30
100854
Calibrated until
May 25, 2018
Item Kind of Equipment
Power Meter
Peak Output Power Measurement
Manufacturer
Type No.
Serial No.
Anritsu
ML2495A
1128008
Calibrated until
Aug. 16, 2018
Power Sensor
Anritsu
MA2411B
1126001
Aug. 16, 2018
Antenna Conducted Spurious Emission Measurement
Item Kind of Equipment
Manufacturer
Type No.
Serial No.
Calibrated until
R&S
R&S/FSP30
100854
May 25, 2018
Spectrum Analyzer
Item Kind of Equipment
1 Spectrum Analyzer
Power Spectral Density Measurement
Manufacturer
Type No.
Serial No.
R&S
R&S/FSP30
100854
Calibrated until
May 25, 2018
Remark: ”N/A” denotes no model name, serial no. or calibration specified.
All calibration period of equipment list is one year.
Report No.: BTL-FCCP-2-1711095
Page 26 of 62
APPENDIX A - CONDUCTED EMISSION
Report No.: BTL-FCCP-2-1711095
Page 31 of 62
Test Mode:
TX Mode
Line
Report No.: BTL-FCCP-2-1711095
Page 32 of 62
Test Mode:
TX Mode
Neutral
Report No.: BTL-FCCP-2-1711095
Page 33 of 62
APPENDIX B - RADIATED EMISSION (9KHZ TO 30MHZ)
Report No.: BTL-FCCP-2-1711095
Page 34 of 62
Test Mode:
TX Mode
Ant 0°
Report No.: BTL-FCCP-2-1711095
Page 35 of 62
Test Mode:
TX Mode
Ant 0°
Report No.: BTL-FCCP-2-1711095
Page 36 of 62
Test Mode:
TX Mode
Ant 90°
Report No.: BTL-FCCP-2-1711095
Page 37 of 62
Test Mode:
TX Mode
Ant 90°
Report No.: BTL-FCCP-2-1711095
Page 38 of 62
APPENDIX C - RADIATED EMISSION (30MHZ TO 1000MHZ)
Report No.: BTL-FCCP-2-1711095
Page 39 of 62
Test Mode:
TX Mode 2480MHz _CH39_1Mbps
Vertical
Report No.: BTL-FCCP-2-1711095
Page 40 of 62
Test Mode:
TX Mode 2480MHz _CH39_1Mbps
Horizontal
Report No.: BTL-FCCP-2-1711095
Page 41 of 62
APPENDIX D - RADIATED EMISSION (ABOVE 1000MHZ)
Report No.: BTL-FCCP-2-1711095
Page 42 of 62
Test Mode
TX Mode 2402MHz _CH00_1Mbps
Vertical
Report No.: BTL-FCCP-2-1711095
Page 43 of 62
Test Mode
TX Mode 2402MHz _CH00_1Mbps
Vertical
Report No.: BTL-FCCP-2-1711095
Page 44 of 62
Test Mode
TX Mode 2402MHz _CH00_1Mbps
Horizontal
Report No.: BTL-FCCP-2-1711095
Page 45 of 62
Test Mode
TX Mode 2402MHz _CH00_1Mbps
Horizontal
Report No.: BTL-FCCP-2-1711095
Page 46 of 62
Test Mode
TX Mode 2440MHz _CH19_1Mbps
Vertical
Report No.: BTL-FCCP-2-1711095
Page 47 of 62
Test Mode
TX Mode 2440MHz _CH19_1Mbps
Vertical
Report No.: BTL-FCCP-2-1711095
Page 48 of 62
Test Mode
TX Mode 2440MHz _CH19_1Mbps
Horizontal
Report No.: BTL-FCCP-2-1711095
Page 49 of 62
Test Mode
TX Mode 2440MHz _CH19_1Mbps
Horizontal
Report No.: BTL-FCCP-2-1711095
Page 50 of 62
Test Mode
TX Mode 2480MHz _CH39_1Mbps
Vertical
Report No.: BTL-FCCP-2-1711095
Page 51 of 62
Test Mode
TX Mode 2480MHz _CH39_1Mbps
Vertical
Report No.: BTL-FCCP-2-1711095
Page 52 of 62
Test Mode
TX Mode 2480MHz _CH39_1Mbps
Horizontal
Report No.: BTL-FCCP-2-1711095
Page 53 of 62
Test Mode
TX Mode 2480MHz _CH39_1Mbps
Horizontal
Report No.: BTL-FCCP-2-1711095
Page 54 of 62
APPENDIX E - BANDWIDTH
Report No.: BTL-FCCP-2-1711095
Page 55 of 62
Test Mode:
TX Mode 2402MHz/2440MHz/2480MHz_1Mbps
Frequency
99% Occupied BW
(MHz)
1.05
Min. Limit
(kHz)
Test Result
2402
6dB Bandwidth
(MHz)
0.70
500
Pass
2440
0.68
1.04
500
Pass
2480
0.70
1.04
500
Pass
(MHz)
2402 MHz
Report No.: BTL-FCCP-2-1711095
2440 MHz
2480 MHz
Page 56 of 62
APPENDIX F - MAXIMUM OUTPUT POWER TEST
Report No.: BTL-FCCP-2-1711095
Page 57 of 62
Test Mode :
TX Mode 2402MHz/2440MHz/2480MHz_1Mbps
Frequency
Conducted
Conducted
Max. Limit
Max. Limit
(MHz)
Power (dBm)
Power (W)
(dBm)
(W)
2402
8.46
0.0070
30.00
1.00
Pass
2440
7.14
0.0052
30.00
1.00
Pass
2480
7.39
0.0055
30.00
1.00
Pass
Report No.: BTL-FCCP-2-1711095
Test Result
Page 58 of 62
APPENDIX G - ANTENNA CONDUCTED SPURIOUS EMISSION
Report No.: BTL-FCCP-2-1711095
Page 59 of 62
Test Mode :
TX Mode 2402MHz/2440MHz/2480MHz_1Mbps
2402 MHz_ Lower
2480 MHz_ Upper
2402 MHz – 10 Harmonics
2440 MHz – 10 Harmonics
2480 MHz – 10 Harmonics
Report No.: BTL-FCCP-2-1711095
Page 60 of 62
APPENDIX H - POWER SPECTRAL DENSITY TEST
Report No.: BTL-FCCP-2-1711095
Page 61 of 62
Test Mode:
TX Mode 2402MHz/2440MHz/2480MHz_1Mbps
Frequency
Power Density
Max. Limit
(MHz)
(dBm/3kHz)
(dBm/3kHz)
2402
-8.19
8.00
Pass
2440
-9.58
8.00
Pass
2480
-9.32
8.00
Pass
2402 MHz
Report No.: BTL-FCCP-2-1711095
2440 MHz
Test Result
2480 MHz
Page 62 of 62
Download: A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Mirror Download [FCC.gov]A01SPK BbSPEAKER Test Report Measurement Report IHR FAC INC.
Document ID3955496
Application IDdiRy5Cmf82UXCkSyeTIplA==
Document DescriptionTest Report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize139.79kB (1747414 bits)
Date Submitted2018-08-08 00:00:00
Date Available2018-08-08 00:00:00
Creation Date2018-04-19 10:01:38
Producing SoftwareMicrosoft® Word 2010
Document Lastmod2018-04-30 11:20:34
Document TitleMeasurement Report
Document CreatorMicrosoft® Word 2010
Document Author: USER

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : USER
Create Date                     : 2018:04:19 10:01:38+08:00
Modify Date                     : 2018:04:30 11:20:34+08:00
Has XFA                         : No
Language                        : zh-TW
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : USER
Title                           : Measurement Report
Creator Tool                    : Microsoft® Word 2010
Metadata Date                   : 2018:04:30 11:20:34+08:00
Producer                        : Microsoft® Word 2010
Document ID                     : uuid:1f6a834b-4e8c-46cd-9929-c61836199bf1
Instance ID                     : uuid:c96289e3-90ea-42c8-a78a-4cec35426d1a
Page Count                      : 58