BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd

birde pty ltd Portable Media Console for Children

Page 1 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 2 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 3 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 4 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 5 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 6 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 7 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 8 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 9 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 10 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 11 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 12 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 13 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 14 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 15 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 16 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 17 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 18 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 19 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 20 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 21 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 22 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 23 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 24 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 25 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 26 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 27 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 28 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 29 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 30 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 31 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 32 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 33 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 34 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Page 35 of BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd

SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen,
Guangdong, China 518057
Telephone:
+86 (0) 755 2601 2053
Fax:
+86 (0) 755 2671 0594
Email:
ee.shenzhen@sgs.com
Report No.: SZEM170900938306
Page
: 1 of 35
FCC SAR TEST REPORT
Applicant:
SZEM1709009383CR
birde Pty Ltd
Manufacturer:
birde Pty Ltd
Application No:
Product Name:
Portable Media Console for Children
Model No.(EUT):
BC300
Trade Mark:
birde
FCC ID:
2ANOV-BC03
Standards:
FCC 47CFR §2.1093
Date of Receipt:
2017-10-13
Date of Test:
2017-10-16 to 2017-10-16
Date of Issue:
2017-11-08
Test Result:
PASS *
In the configuration tested, the EUT detailed in this report complied with the standards specified above.
Authorized Signature:
Derek Yang
Wireless Laboratory Manager
The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report.
If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system
complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical
Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical
Approvals in writing.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within
the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of
this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
2 of 35
REVISION HISTORY
Revision Record
Version
01
Chapter
Date
2017-11-08
Modifier
Remark
Original
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
3 of 35
TEST SUMMARY
Maximum Reported SAR(W/kg)
Frequency Band
Body
WI-FI (2.4GHz)
0.60
SAR Limited(W/kg)
1.6
Approved & Released by
Simon Ling
SAR Manager
Tested by
Evan Mi
SAR Engineer
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
4 of 35
CONTENTS
GENERAL INFORMATION .....................................................................................................................................5
1.1
1.2
1.3
1.4
1.5
1.6
DETAILS OF CLIENT ...........................................................................................................................................5
T EST LOCATION .................................................................................................................................................5
T EST FACILITY ...................................................................................................................................................6
GENERAL DESCRIPTION OF EUT .......................................................................................................................7
T EST SPECIFICATION .........................................................................................................................................8
RF EXPOSURE LIMITS.........................................................................................................................................8
SAR MEASUREMENTS SYSTEM CONFIGURATION ........................................................................................9
2.1
T HE SAR MEASUREMENT SYSTEM ....................................................................................................................9
2.2
ISOTROPIC E-FIELD PROBE EX3DV4 .............................................................................................................. 10
2.3
DATA ACQUISITION ELECTRONICS (DAE)........................................................................................................ 11
2.4
SAM T WIN PHANTOM ...................................................................................................................................... 11
2.5
ELI PHANTOM .................................................................................................................................................. 12
2.6
DEVICE HOLDER FOR T RANSMITTERS .............................................................................................................. 13
2.7
MEASUREMENT PROCEDURE ............................................................................................................................ 14
2.7.1 Scanning procedure .................................................................................................................................. 14
2.7.2 Data Storage ............................................................................................................................................. 16
2.7.3 Data Evaluation by SEMCAD................................................................................................................... 16
DESCRIPTION OF TEST POSITION ................................................................................................................... 18
3.1
T HE BODY T EST POSITION............................................................................................................................... 18
SAR SYSTEM VERIFICATION PROCEDURE.................................................................................................... 19
4.1
T ISSUE SIMULATE LIQUID ................................................................................................................................ 19
4.1.1 Recipes for Tissue Simulate Liquid ......................................................................................................... 19
4.1.2 Measurement for Tissue Simulate Liquid ................................................................................................ 20
4.2
SAR SYSTEM VALIDATION............................................................................................................................... 21
4.2.1 Justification for Extended SAR Dipole Calibrations ................................................................................ 22
4.2.2 Summary System Validation Result(s) .................................................................................................... 23
4.2.3 Detailed System Validation Results........................................................................................................ 23
TEST RESULTS AND MEASUREMENT DATA ................................................................................................. 24
5.1
W IFI TEST CONFIGURATION ............................................................................................................................. 24
5.1.1 Initial Test Position SAR Test Reduction Procedure .............................................................................. 24
5.1.2 DUT Antenna Locations ........................................................................................................................... 27
5.1.3 EUT side for SAR Testing ........................................................................................................................ 29
5.2
MEASUREMENT OF RF CONDUCTED POWER .................................................................................................... 30
5.2.1 Conducted Power of WIFI2.4G ................................................................................................................ 30
5.3
MEASUREMENT OF SAR DATA ........................................................................................................................ 31
5.3.1 SAR Result Of WIFI2.4G .......................................................................................................................... 31
EQUIPMENT LIST.................................................................................................................................................. 32
MEASUREMENT UNCERTAINTY ....................................................................................................................... 33
CALIBRATION CERTIFICATE ............................................................................................................................. 34
PHOTOGRAPHS.................................................................................................................................................... 34
APPENDIX A: DETAILED SYSTEM VALIDATION RESULTS .................................................................................. 35
APPENDIX B: DETAILED TEST RESULTS................................................................................................................. 35
APPENDIX C: CALIBRATION CERTIFICATE............................................................................................................. 35
APPENDIX D: PHOTOGRAPHS ................................................................................................................................... 35
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
5 of 35
General Information
1.1 Details of Client
Applicant:
birde Pty Ltd
Address:
PO BOX 265 St Leonards 1590 Australia
Manufacturer:
birde Pty Ltd
PO BOX 265 St Leonards 1590 Australia
Address:
1.2 Test Location
Company:
SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch
Address:
No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen,
Guangdong, China
Post code:
518057
Telephone:
+86 (0) 755 2601 2053
Fax:
+86 (0) 755 2671 0594
E-mail:
ee.shenzhen@sgs.com
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
6 of 35
1.3 Test Facility
The test facility is recognized, certified, or accredited by the following organizations:
• CNAS (No. CNAS L2929)
CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC
Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories
(CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the
competence in the field of testing.
• A2LA (Certificate No. 3816.01)
SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American
Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01.
• VCCI
The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services Co., Ltd.
have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.:
G-823, R-4188, T-1153 and C-2383 respectively.
• FCC –Designation Number: CN1178
SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an
accredited testing laboratory.
Designation Number: CN1178. Test Firm Registration Number: 406779.
• Industry Canada (IC)
Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards Technical
Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of
Industry Canada for radio equipment testing with Registration No.: 4620C-1, 4620C-2, 4620C-3.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
7 of 35
1.4 General Description of EUT
Product Name:
Portable Media Console for Children
Model No.(EUT):
BC300
Trade Mark:
birde
Product Phase:
production unit
Device Type :
portable device
Exposure Category:
uncontrolled environment / general population
FCC ID
2ANOV-BC03
Hardware Version:
Version 1
Software Version:
Version 1
Antenna Type:
PCB printed antenna
Device Operating Configurations :
Modulation Mode:
Frequency Bands:
WIFI: DSSS, OFDM
Band
Tx (MHz)
Rx (MHz)
WIFI
2412-2462
2412-2462
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
8 of 35
1.5 Test Specification
Identity
Document Title
FCC 47CFR §2.1093
Radiofrequency Radiation Exposure Evaluation: Portable Devices
IEEE Std C95.1 – 1991
IEEE Standard for Safety Levels with Respect to Human Exposure to
Radio Frequency Electromagnetic Fields, 3 kHz – 300 GHz.
KDB 248227 D01 802.11 Wi-Fi SAR
v02r02
SAR GUIDANCE FOR IEEE 802.11 (Wi-Fi) TRANSMITTERS
KDB447498 D01 General RF Exposure Mobile and Portable Devices RF Exposure Procedures and
Guidance v06
Equipment Authorization Policies
KDB447498 D03 Supplement C CrossReference v01
OET Bulletin 65, Supplement C Cross-Reference
KDB 865664 D01 SAR Measurement
100 MHz to 6 GHz v01r04
SAR Measurement Requirements for 100 MHz to 6 GHz
KDB 865664 D02
Reporting v01r02
RF
Exposure
Considerations
RF
Exposure
Compliance
Reporting
and
Documentation
1.6 RF exposure limits
Uncontrolled Environment
General Population
Controlled Environment
Occupational
Spatial Peak SAR*
(Brain*Trunk)
1.60 W/kg
8.00 W/kg
Spatial Average SAR**
(Whole Body)
0.08 W/kg
0.40 W/kg
Spatial Peak SAR***
(Hands/Feet/Ankle/Wrist)
4.00 W/kg
20.00 W/kg
Human Exposure
Notes:
* The Spatial Peak value of the SAR averaged over any 1 gram of tissue (defined as a tissue volume in the
shape of a cube) and over the appropriate averaging time
** The Spatial Average value of the SAR averaged over the whole body.
*** The Spatial Peak value of the SAR averaged over any 10 grams of tissue (defined as a tissue volume in the
shape of a cube) and over the appropriate averaging time.
Uncontrolled Environments are defined as locations where there is the exposure of individuals who have no
knowledge or control of their exposure.
Controlled Environments are defined as locations where there is exposure that may be incurred by persons
who are aware of the potential for exposure (i.e. as a result of employment or occupation).
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
9 of 35
SAR Measurements System Configuration
2.1 The SAR Measurement System
This SAR Measurement System uses a Computer-controlled 3-D stepper motor system (SPEAG DASY5
professional system). A E-field probe is used to determine the internal electric fields. The SAR can be obtained
from the equation SAR= σ (|Ei|2)/ ρ where σ and ρ are the conductivity and mass density of the tissueSimulate.
The DASY5 system for performing compliance tests consists of the following items:
A standard high precision 6-axis robot (Stabile RX family) with controller, teach pendant and software .An arm
extension for accommodation the data acquisition electronics (DAE).
A dosimetric probe, i.e., an isotropic E-field probe optimized and calibrated for usage in tissue simulating liquid.
The probe is equipped with an optical surface detector system.
A data acquisition electronics (DAE) which performs the signal amplification, signal multiplexing, ADconversion, offset measurements, mechanical surface detection, collision detection, etc. The unit is battery
powered with standard or rechargeable batteries. The signal is optically transmitted to the EOC.
The Electro-optical converter (EOC) performs the conversion between optical and electrical of the signals for
the digital communication to DAE and for the analog signal from the optical surface detection. The EOC is
connected to the measurement server.
F-1. SAR Measurement System Configuration
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
10 of 35
The function of the measurement server is to perform the time critical tasks such as signal filtering, control
of the robot operation and fast movement interrupts.
A probe alignment unit which improves the (absolute) accuracy of the probe positioning.
A computer operating Windows 7.
DASY5 software.
Remote control with teach pendant and additional circuitry for robot safety such as warning lamps, etc.
The SAM twin phantom enabling testing left-hand, right-hand and Body Worn usage.
The device holder for handheld mobile phones.
Tissue simulating liquid mixed according to the given recipes.
Validation dipole kits allowing to validating the proper functioning of the system.
2.2 Isotropic E-field Probe EX3DV4
Symmetrical design with triangular core
Built-in shielding against static charges
PEEK enclosure material (resistant to organic solvents, e.g., DGBE)
Calibration
ISO/IEC 17025 calibration service available.
Frequency
10 MHz to > 6 GHz
Linearity: ± 0.2 dB (30 MHz to 6 GHz)
Directivity
± 0.3 dB in TSL (rotation around probe axis)
± 0.5 dB in TSL (rotation normal to probe axis)
Dynamic Range
10 µW/g to > 100 mW/g
Linearity: ± 0.2 dB (noise: typically < 1 µW/g)
Dimensions
Overall length: 337 mm (Tip: 20 mm)
Tip diameter: 2.5 mm (Body: 12 mm)
Typical distance from probe tip to dipole centers: 1 mm
Application
High precision dosimetric measurements in any exposure scenario
(e.g., very strong gradient fields); the only probe that enables
compliance testing for frequencies up to 6 GHz with precision of better
30%.
Compatibility
DASY3, DASY4, DASY52 SAR and higher, EASY4/MRI
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
11 of 35
2.3 Data Acquisition Electronics (DAE)
Model
DAE3,DAE4
Construction
Signal amplifier, multiplexer, A/D converter
and control logic. Serial optical link for
communication with DASY4/5 embedded
system (fully remote controlled). Two step
probe touch detector for mechanical
surface detection and emergency robot
stop.
Measurement
Range
-100 to +300 mV (16 bit resolution and two
range settings: 4mV,400mV)
Input Offset Voltage
< 5µV (with auto zero)
Input Bias Current
< 50 f A
Dimensions
60 x 60 x 68 mm
2.4 SAM Twin Phantom
Material
Vinylester, glass fiber reinforced (VEGF)
Liquid Compatibility
Compatible with all SPEAG tissue
simulating liquids (incl. DGBE type)
Shell Thickness
2 ± 0.2 mm (6 ± 0.2 mm at ear point)
Dimensions
(incl. Wooden
Support)
Length: 1000 mm
Width: 500 mm
Height: adjustable feet
Filling Volume
approx. 25 liters
Wooden Support
SPEAG standard phantom table
The shell corresponds to the specifications of the Specific Anthropomorphic Mannequin (SAM) phantom
defined in IEEE 1528 and IEC 62209-1. It enables the dosimetric evaluation of left and right hand phone
usage as well as body mounted usage at the flat phantom region. A cover prevents evaporation of the
liquid. Reference markings on the phantom allow the complete setup of all predefined phantom positions
and measurement grids by teaching three points with the robot.
Twin SAM V5.0 has the same shell geometry and is manufactured from the same material as Twin SAM
V4.0, but has reinforced top structure.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
12 of 35
2.5 ELI Phantom
Material
Vinylester, glass fiber reinforced (VE-GF)
Liquid
Compatible with all SPEAG tissue
Compatibility
simulating liquids (incl. DGBE type)
Shell Thickness
2.0 ± 0.2 mm (bottom plate)
Dimensions
Major axis: 600 mm
Minor axis: 400 mm
Filling Volume
approx. 30 liters
Wooden Support
SPEAG standard phantom table
Phantom for compliance testing of handheld and body-mounted wireless devices in the frequency range
of 30 MHz to 6 GHz. ELI is fully compatible with the IEC 62209-2 standard and all known tissue simulating
liquids. ELI has been optimized regarding its performance and can be integrated into our standard
phantom tables. A cover prevents evaporation of the liquid. Reference markings on the phantom allow
installation of the complete setup, including all predefined phantom positions and measurement grids, by
teaching three points. The phantom is compatible with all SPEAG dosimetric probes and dipoles.
ELI V5.0 has the same shell geometry and is manufactured from the same material as ELI4, but has
reinforced top structure.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
13 of 35
2.6 Device Holder for Transmitters
F-2. Device Holder for Transmitters
The DASY device holder is designed to cope with different positions given in the standard. It has two scales
for the device rotation (with respect to the body axis) and the device inclination (with respect to the line
between the ear reference points). The rotation centres for both scales are the ear reference point (ERP).
Thus the device needs no repositioning when changing the angles.
The DASY device holder has been made out of low-loss POM material having the following dielectric
parameters: relative permittivity ε=3 and loss tangent δ=0.02. The amount of dielectric material has been
reduced in the closest vicinity of the device, since measurements have suggested that the influence of the
clamp on the test results could thus be lowered.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
14 of 35
2.7
Measurement procedure
2.7.1 Scanning procedure
Step 1: Power reference measurement
The “reference” and “drift” measurements are located at the beginning and end of the batch process. They
measure the field drift at one single point in the liquid over the complete procedure.
Step 2: Area scan
The SAR distribution at the exposed side of the head was measured at a distance of 4mm from the inner
surface of the shell. The area covered the entire dimension of the head and the horizontal grid spacing was
15mm*15mm or 12mm*12mm or 10mm*10mm.Based on the area scan data, the area of the maximum
absorption was determined by spline interpolation.
Step 3: Zoom scan
Around this point, a volume of 30mm*30mm*30mm (fine resolution volume scan, zoom scan) was assessed by
measuring 5x5x7 points (≤2GHz) and 7x7x7 points (≥2GHz). On this basis of this data set, the spatial peak
SAR value was evaluated with the following procedure:
The data at the surface was extrapolated, since the centre of the dipoles is 2.0mm away from the tip of the
probe and the distance between the surface and the lowest measuring point is 1.2mm. (This can be variable.
Refer to the probe specification).The extrapolation was based on a least square algorithm. A polynomial of the
fourth order was calculated through the points in z-axes. This polynomial was then used to evaluate the points
between the surface and the probe tip. The maximum interpolated value was searched with a straight-forward
algorithm. Around this maximum the SAR values averaged over the spatial volumes (1g or 10g) were computed
using the 3D-Spline interpolation algorithm. The volume was integrated with the trapezoidal algorithm. One
thousand points were interpolated to calculate the average. All neighbouring volumes were evaluated until no
neighboring volume with a higher average value was found.
The area and zoom scan resolutions specified in the table below must be applied to the SAR measurements
Probe boundary effect error compensation is required for measurements with the probe tip closer than half a
probe tip diameter to the phantom surface. Both the probe tip diameter and sensor offset distance must satisfy
measurement protocols; to ensure probe boundary effect errors are minimized and the higher fields closest to
the phantom surface can be correctly measured and extrapolated to the phantom surface for computing 1-g
SAR. Tolerances of the post-processing algorithms must be verified by the test laboratory for the scan
resolutions used in the SAR measurements, according to the reference distribution functions specified in IEEE
Std. 1528-2013.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
15 of 35
Step 4: Power reference measurement (drift)
The Power Drift Measurement job measures the field at the same location as the most recent power reference
measurement job within the same procedure, and with the same settings. The indicated drift is mainly the
variation of the DUT’s output power and should vary max. ± 5 %
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
16 of 35
2.7.2 Data Storage
The DASY software stores the acquired data from the data acquisition electronics as raw data (in microvolt
readings from the probe sensors), together with all necessary software parameters for the data evaluation (probe
calibration data, liquid parameters and device frequency and modulation data) in measurement files with the
extension “.DAE3”. The software evaluates the desired unit and format for output each time the data is visualized
or exported. This allows verification of the complete software setup even after the measurement and allows
correction of incorrect parameter settings. For example, if a measurement has been performed with a wrong crest
factor parameter in the device setup, the parameter can be corrected afterwards and the data can be re-evaluated.
The measured data can be visualized or exported in different units or formats, depending on the selected probe
type ([V/m], [A/m], [°C], [m W/g], [m W/cm²], [dBrel], etc.). Some of these units are not available in certain
situations or show meaningless results, e.g., a SAR output in a lossless media will always be zero. Raw data can
also be exported to perform the evaluation with other software packages.
2.7.3 Data Evaluation by SEMCAD
The SEMCAD software automatically executes the following procedures to calculate the field units from the
microvolt readings at the probe connector. The parameters used in the evaluation are stored in the configuration
modules of the software:
Probe parameters: - Sensitivity
- Conversion factor
ConvFi
- Diode compression point
Dcpi
Device parameters: - Frequency
- Crest factor
cf
Media parameters: - Conductivity
- Density
ρ
Normi, ai0, ai1, ai2
ε
These parameters must be set correctly in the software. They can be found in the component documents or they
can be imported into the software from the configuration files issued for the DASY components. In the direct
measuring mode of the multimeter option, the parameters of the actual system setup are used. In the scan
visualization and export modes, the parameters stored in the corresponding document files are used.
The first step of the evaluation is a linearization of the filtered input signal to account for the compression
characteristics of the detector diode. The compensation depends on the input signal, the diode type and the DCtransmission factor from the diode to the evaluation electronics.
If the exciting field is pulsed, the crest factor of the signal must be known to correctly compensate for peak power.
The formula for each channel can be given as:
With
Vi
= compensated signal of channel i ( i = x, y, z )
Ui = input signal of channel i ( i = x, y, z )
cf = crest factor of exciting field (DASY parameter)
dcp i = diode compression point (DASY parameter)
From the compensated input signals the primary field data for each channel can be evaluated:
E-field probes:
H-field probes:
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
17 of 35
With
Vi = compensated signal of channel i
Normi = sensor sensitivity of channel I
(i = x, y, z)
[mV/(V/m)2] for E-field Probes
ConvF = sensitivity enhancement in solution
aij = sensor sensitivity factors for H-field probes
f = carrier frequency [GHz]
Ei = electric field strength of channel i in V/m
(i = x, y, z)
Hi = magnetic field strength of channel i in A/m
The RSS value of the field components gives the total field strength (Hermitian magnitude):
The primary field data are used to calculate the derived field units.
with
SAR = local specific absorption rate in mW/g
Etot = total field strength in V/m
σ= conductivity in [mho/m] or [Siemens/m]
ε= equivalent tissue density in g/cm3
Note that the density is normally set to 1 (or 1.06), to account for actual brain density rather than the density of the
simulation liquid. The power flow density is calculated assuming the excitation field to be a free space field.
or
with Ppwe = equivalent power density of a plane wave in mW/cm2
Etot = total electric field strength in V/m
Htot = total magnetic field strength in A/m
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
18 of 35
Description of Test Position
3.1 The Body Test Position
Per KDB inquiry, SAR can test the sides near the antenna, the surface of the device should be tested for SAR
compliance with the device touching the phantom. The SAR Exclusion Threshold in KDB 447498 D01 can be
applied to determine SAR test exclusion for adjacent edge configurations. The closest distance from the antenna
to an adjacent device surface is used to determine if SAR testing is required for the adjacent surfaces, with the
adjacent surface positioned against the phantom and the surface containing the antenna positioned perpendicular
to the phantom.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
19 of 35
SAR System Verification Procedure
4.1
Tissue Simulate Liquid
4.1.1 Recipes for Tissue Simulate Liquid
The bellowing tables give the recipes for tissue simulating liquids to be used in different frequency bands:
Ingredients
Frequency (MHz)
(% by weight)
2450
Tissue Type
Body
Water
68.53
Salt (NaCl)
0.1
Sucrose
HEC
Bactericide
Tween
31.37
Salt: 99+% Pure Sodium Chloride
Sucrose: 98+% Pure Sucrose
Water: De-ionized, 16 MΩ+ resistivity
HEC: Hydroxyethyl Cellulose
Tween: Polyoxyethylene (20) sorbitan monolaurate
Table 1: Recipe of Tissue Simulate Liquid
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
20 of 35
4.1.2 Measurement for Tissue Simulate Liquid
The dielectric properties for this Tissue Simulate Liquids were measured by using the Agilent Model 85070E
Dielectric Probe in conjunction with Agilent E5071C Network Analyzer (300 KHz-8500 MHz). The Conductivity
(σ) and Permittivity (ρ) are listed in Table 2.For the SAR measurement given in this report. The temperature
variation of the Tissue Simulate Liquids was 22±2°C.
Tissue
Type
Measured
Frequency
(MHz)
)
2450
Body
2450
Target Tissue (±5%)
Measured Tissue
Liquid
Temp.
εr
σ(S/m)
εr
σ(S/m)
(℃
℃)
52.70
(50.07~55.34)
1.95
(1.85~2.05)
52.319
1.994
22
Measured Date
2017/10/16
Table 2: Measurement result of Tissue electric parameters
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
21 of 35
4.2
SAR System Validation
The microwave circuit arrangement for system verification is sketched in F-12. The daily system accuracy
verification occurs within the flat section of the SAM phantom. A SAR measurement was performed to see if the
measured SAR was within +/- 10% from the target SAR values. The tests were conducted on the same days as
the measurement of the EUT. The obtained results from the system accuracy verification are displayed in the
table 3 (A power level of 250mw was input to the dipole antenna). During the tests, the ambient temperature of
the laboratory was in the range 22±2°C, the relative humidity was in the range 60% and the liquid depth above
the ear reference points was above 15 cm in all the cases. It is seen that the system is operating within its
specification, as the results are within acceptable tolerance of the reference values.
F-3. the microwave circuit arrangement used for SAR system verification
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
22 of 35
4.2.1 Justification for Extended SAR Dipole Calibrations
1) Referring to KDB865664 D01 requirements for dipole calibration, instead of the typical annual calibration
recommended by measurement standards, longer calibration intervals of up to three years may be considered
when it is demonstrated that the SAR target, impedance and return loss of a dipole have remain stable according
to the following requirements. Each measured dipole is expected to evaluate with the following criteria at least on
annual interval in Appendix C.
a) There is no physical damage on the dipole;
b) System check with specific dipole is within 10% of calibrated value;
c) Return-loss is within 10% of calibrated measurement;
d) Impedance is within 5Ω from the previous measurement.
2) Network analyzer probe calibration against air, distilled water and a shorting block performed before measuring
liquid parameters.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
23 of 35
4.2.2 Summary System Validation Result(s)
Validation Kit
D2450V2
Body
Table 3:
Measured
SAR
250mW
Measured
SAR
250mW
Measured
SAR
(normaliz
ed to 1w)
Measured
SAR
(normalize
d to 1w)
Target SAR
(normalized
to 1w)
(±10%)
Target SAR
(normalized to
1w)
(±10%)
1g (W/kg)
10g (W/kg)
1g (W/kg)
10g (W/kg)
1-g(W/kg)
10-g(W/kg)
12.8
51.2
24
51.0
(45.9~56.1)
23.5
(21.15~25.85)
Liquid
Temp.
(℃
℃)
Measured
Date
22
2017/10/16
SAR System Validation Result
4.2.3 Detailed System Validation Results
Please see the Appendix A
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
24 of 35
Test results and Measurement Data
5.1 WiFi Test Configuration
A Wi-Fi device must be configured to transmit continuously at the required data rate, channel bandwidth and
signal modulation, using the highest transmission duty factor supported by the test mode tools for SAR
measurement.
Duty cycle=8.412/8.477=99.23%
5.1.1 Initial Test Position SAR Test Reduction Procedure
DSSS and OFDM configurations are considered separately according to the required SAR procedures. SAR is
measured in the initial test position using the 802.11 transmission mode configuration required by the DSSS
procedure or initial test configuration and subsequent test configuration(s) according to the OFDM procedures.
The initial test position procedure is described in the following:
1). When the reported SAR of the initial test position is ≤ 0.4 W/kg, further SAR measurement is not required for
the other (remaining) test positions in that exposure configuration and 802.11 transmission mode
combinations within the frequency band or aggregated band. SAR is also not required for that exposure
configuration in the subsequent test configuration(s).
2). When the reported SAR of the initial test position is > 0.4 W/kg, SAR is repeated for the 802.11 transmission
mode configuration tested in the initial test position using subsequent highest extrapolated or estimated 1-g
SAR conditions determined by area scans or next closest/smallest test separation distance and maximum RF
coupling test positions based on manufacturer justification, on the highest maximum output power channel,
until the reported SAR is ≤ 0.8 W/kg or all required test positions (left, right, touch, tilt or subsequent surfaces
and edges) are tested.
3). For all positions/configurations tested using the initial test position and subsequent test positions, when the
reported SAR is > 0.8 W/kg, SAR is measured for these test positions/configurations on the subsequent next
highest measured output power channel(s) until the reported SAR is ≤ 1.2 W/kg or all required channels are
tested. a) Additional power measurements may be required for this step, which should be limited to those
necessary for identifying the subsequent highest output power channels.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
25 of 35
5.1.1.1 Initial Test Configuration Procedures
An initial test configuration is determined for OFDM transmission modes according to the channel bandwidth,
modulation and data rate combination(s) with the highest maximum output power specified for production units in
each standalone and aggregated frequency band. SAR is measured using the highest measured maximum output
power channel. For configurations with the same specified or measured maximum output power, additional
transmission mode and test channel selection procedures are required. SAR test reduction for subsequent
highest output test channels is determined according to reported SAR of the initial test configuration.
For next to the ear, hotspot mode and UMC mini-tablet exposure configurations where multiple test positions are
required, the initial test position procedure is applied to minimize the number of test positions required for SAR
measurement using the initial test configuration transmission mode. For fixed exposure conditions that do not
have multiple SAR test positions, SAR is measured in the transmission mode determined by the initial test
configuration.
When the reported SAR of the initial test configuration is > 0.8 W/kg, SAR measurement is required for
subsequent next highest measured output power channel(s) in the initial test configuration until reported SAR is ≤
1.2 W/kg or all required channels are tested.
5.1.1.2 Subsequent Test Configuration Procedures
SAR measurement requirements for the remaining 802.11 transmission mode configurations that have not been
tested in the initial test configuration are determined separately for each standalone and aggregated frequency
band, in each exposure condition, according to the maximum output power specified for production units. The
initial test position procedure is applied to next to the ear, UMPC mini-tablet and hotspot mode configurations.
When the same maximum output power is specified for multiple transmission modes, additional power
measurements may be required to determine if SAR measurements are required for subsequent highest output
power channels in a subsequent test configuration. The subsequent test configuration and SAR measurement
procedures are described in the following.
1). When SAR test exclusion provisions of KDB Publication 447498 are applicable and SAR measurement
is not required for the initial test configuration, SAR is also not required for the next highest maximum
output power transmission mode subsequent test configuration(s) in that frequency band or aggregated
band and exposure configuration.
2). When the highest reported SAR for the initial test configuration (when applicable, include subsequent
highest output channels), according to the initial test position or fixed exposure position requirements, is
adjusted by the ratio of the subsequent test configuration to initial test configuration specified maximum
output power and the adjusted SAR is ≤ 1.2 W/kg, SAR is not required for that subsequent test
configuration.
3). The number of channels in the initial test configuration and subsequent test configuration can be
different due to differences in channel bandwidth. When SAR measurement is required for a subsequent
test configuration and the channel bandwidth is smaller than that in the initial test configuration, all
channels in the subsequent test configuration that overlap with the larger bandwidth channel tested in
the initial test configuration should be used to determine the highest maximum output power channel.
This step requires additional power measurement to identify the highest maximum output power channel
in the subsequent test configuration to determine SAR test reduction.
a)SAR should first be measured for the channel with highest measured output power in the
subsequent test configuration.
b) SAR for subsequent highest measured maximum output power channels in the subsequent test
configuration is required only when the reported SAR of the preceding higher maximum output
power channel(s) in the subsequent test configuration is > 1.2 W/kg or until all required
channels are tested. i) For channels with the same measured maximum output power, SAR
should be measured using the channel closest to the center frequency of the larger channel
bandwidth channel in the initial test configuration.
4). SAR measurements for the remaining highest specified maximum output power OFDM transmission
mode configurations that have not been tested in the initial test configuration (highest maximum output)
or subsequent test configuration(s) (subsequent next highest maximum output power) is determined by
recursively applying the subsequent test configuration procedures in this section to the remaining
configurations according to the following:
a)replace “subsequent test configuration” with “next subsequent test configuration” (i.e., subsequent
next highest specified maximum output power configuration)
b) replace “initial test configuration” with “all tested higher output power configurations”
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
26 of 35
5.1.1.3 2.4 GHz SAR Procedures
Separate SAR procedures are applied to DSSS and OFDM configurations in the 2.4 GHz band to simplify DSSS
test requirements. For 802.11b DSSS SAR measurements, DSSS SAR procedure applies to fixed exposure test
position and initial test position procedure applies to multiple exposure test positions. When SAR measurement is
required for an OFDM configuration, the initial test configuration, subsequent test configuration and initial test
position procedures are applied. The SAR test exclusion requirements for 802.11g/n OFDM configurations are
described in following.
802.11b DSSS SAR Test Requirements
SAR is measured for 2.4 GHz 802.11b DSSS using either a fixed test position or, when applicable, the initial test
position procedure. SAR test reduction is determined according to the following:
1). When the reported SAR of the highest measured maximum output power channel for the exposure
configuration is ≤ 0.8 W/kg, no further SAR testing is required for 802.11b DSSS in that exposure
configuration.
2). When the reported SAR is > 0.8 W/kg, SAR is required for that exposure configuration using the next
highest measured output power channel. When any reported SAR is > 1.2 W/kg, SAR is required for the
third channel; i.e., all channels require testing.
2.4 GHz 802.11g/n OFDM SAR Test Exclusion Requirements
When SAR measurement is required for 2.4 GHz 802.11g/n OFDM configurations, the measurement and test
reduction procedures for OFDM are applied (section 5.3, including sub-sections). SAR is not required for the
following 2.4 GHz OFDM conditions.
1). When KDB Publication 447498 SAR test exclusion applies to the OFDM configuration.
2). When the highest reported SAR for DSSS is adjusted by the ratio of OFDM to DSSS specified maximum
output power and the adjusted SAR is ≤ 1.2 W/kg.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
27 of 35
5.1.2 DUT Antenna Locations
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
28 of 35
The distance between Wi-Fi antenna and the five sides as bellow:
Side 1: 0mm; Side 2: 0mm; Side 3: 22mm; Side 4: 15mm; Side 5: 125mm;
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
29 of 35
5.1.3 EUT side for SAR Testing
EUT side for SAR Testing
Antenna
Side1
Side2
Side3
Side4
Side5
Wi-Fi
Yes
Yes
Yes
Yes
No
(1) The SAR exclusion threshold for distances <50mm is defined by the following equation:
(max. power of channel, including tune-up tolerance, mW)
(min. test separation distance, mm)
Frequency (GHz) ≤3.0
(2) The SAR exclusion threshold for distances >50mm is defined by the following equation, as illustrated in KDB
447498 D01 Appendix B:
a) at 100 MHz to 1500 MHz
[Power allowed at numeric threshold for 50 mm in step 1) + (test separation distance - 50 mm)·( f(MHz)/150)] mW
b) at > 1500 MHz and ≤ 6 GHz
[Power allowed at numeric Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
30 of 35
5.2 Measurement of RF conducted Power
5.2.1 Conducted Power of WIFI2.4G
Mode
802.11b
802.11g
802.11n
HT20
Table 4:
Channel
Frequency(MHz)
11
11
11
2412
2437
2462
2412
2437
2462
2412
2437
2462
Data
Rate(Mbps)
Tune up
16.5
14.5
6.5
13.5
Average
Power
(dBm)
SAR Test
16.5
16.3
15.5
14.3
14.1
14.2
13.2
12.9
13.1
Yes
No
No
No
No
No
No
No
No
Conducted Power of WIFI2.4G
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
31 of 35
5.3 Measurement of SAR Data
5.3.1 SAR Result Of WIFI2.4G
Test
position
Test
mode
Test
Ch./Freq.
Duty
Cycle
Duty
Cycle
Scaled
factor
SAR
(W/kg)1g
Power
drift(dB)
Conducted
power(dBm)
Tune up
Limit(dBm)
Scaled
factor
Scaled
SAR(W/kg)
Liquid
Temp.(℃
℃)
Test data (Separate 0mm)
Side 1
802.11b
1/2412
99.23%
1.008
0.591
0.07
16.5
16.5
1.000
0.596
22
Side 2
802.11b
1/2412
99.23%
1.008
0.131
0.14
16.5
16.5
1.000
0.132
22
Side 3
802.11b
1/2412
99.23%
1.008
0.261
0.14
16.5
16.5
1.000
0.263
22
Side 4
802.11b
1/2412
99.23%
1.008
0.114
-0.06
16.5
16.5
1.000
0.115
22
Table 5: SAR of WIFI2.4G for Body
Note:
1)
Test positions of EUT(the distance between the EUT and the phantom is 0mm for all sides)
2)
The maximum Scaled SAR value is marked in bold. Graph results refer to Appendix B
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
32 of 35
Equipment list
Test Platform
Location
SPEAG DASY5 Professional
SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch
Description
Software Reference
SAR Test System (Frequency range 300MHz-6GHz)
DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331)
Hardware Reference
Manufacturer
Model
Serial Number
Calibration
Date
Due date of
calibration
Robot
Staubli
RX90L
F03/5V32A1/A01
NCR
Twin Phantom
SPEAG
SAM 1
TP-1283
NCR
NCR
NCR
DAE
SPEAG
DAE4
896
2017-09-27
2018-09-26
E-Field Probe
SPEAG
EX3DV4
3962
2016-12-19
2017-12-18
Validation Kits
SPEAG
D1750V2
1149
2016-06-23
2019-06-22
Validation Kits
SPEAG
D1900V2
5d028
2016-12-07
2019-12-06
Validation Kits
SPEAG
D1950V3
1138
2016-12-07
2019-12-06
Validation Kits
SPEAG
D2300V2
1072
2016-06-21
2019-06-20
Validation Kits
SPEAG
D2450V2
733
2016-12-07
2019-12-06
Agilent Network
Analyzer
Agilent
E5071C
MY46523590
2017-03-06
2018-03-05
Dielectric Probe Kit
Agilent
85070E
US01440210
NCR
NCR
Universal Radio
Communication Tester
R&S
CMW500
103990
2017-03-06
2018-03-05
RF Bi-Directional
Coupler
Agilent
86205-60001
MY31400031
NCR
NCR
Signal Generator
Agilent
N5171B
MY53050736
2017-03-06
2018-03-05
Preamplifier
Mini-Circuits
ZHL-42W
15542
NCR
NCR
Power Meter
Agilent
E4416A
GB41292095
2017-03-06
2018-03-05
Power Sensor
Agilent
8481H
MY41091234
2017-03-05
2018-03-04
Power Sensor
R&S
NRP-Z92
100025
2017-03-06
2018-03-05
Attenuator
SHX
TS2-3dB
30704
NCR
NCR
Coaxial low pass filter
Mini-Circuits
VLF-2500(+)
NA
NCR
NCR
Coaxial low pass filter
Microlab Fxr
LA-F13
NA
NCR
NCR
50 Ω coaxial load
Mini-Circuits
KARN-50+
00850
NCR
NCR
DC POWER SUPPLY
SAKO
SK1730SL5A
NA
NCR
NCR
Speed reading
thermometer
MingGao
T809
NA
2017-03-08
2018-03-07
Humidity and
Temperature Indicator
KIMTOKA
KIMTOKA
NA
2017-03-08
2018-03-07
Equipment
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
33 of 35
Measurement Uncertainty
Measurements and results are all in compliance with the standards listed. All measurements and results are
recorded and maintained at the laboratory performing the tests and measurement uncertainties are taken into
account when comparing measurements to pass/ fail criteria. The Expanded uncertainty (95% CONFIDENCE
INTERVAL) is 21.60%.
b1
e=
f(d,k)
i=
C*g/e
Uncertainty Component
Section
in P1528
Tol
(%)
Prob .
Dist.
Div.
Ci
(1g)
1g
ui (%)
Vi
(Veff)
Probe calibration
E.2.1
6.5
6.50
∞
Axial isotropy
E.2.2
0.5
√3
0.20
∞
hemispherical isotropy
E.2.2
2.6
√3
Cp
1.06
∞
Boundary effect
E.2.3
1.0
√3
0.58
∞
Linearity
E.2.4
0.6
√3
0.35
∞
System detection limit
E.2.5
0.25
√3
0.14
∞
Readout electronics
E.2.6
0.3
0.30
∞
Response time
E.2.7
√3
0.00
∞
Integration time
E.2.8
2.6
√3
1.50
∞
RF ambient Condition –Noise
E.6.1
√3
1.73
∞
RF ambient Condition reflections
E.6.1
√3
1.73
∞
Probe positioning- mechanical
tolerance
E.6.2
1.5
√3
0.87
∞
Probe positioning- with respect
to phantom
E.6.3
2.9
√3
1.67
∞
Max. SAR evaluation
E.5.2
√3
0.58
∞
Test sample positioning
E.4.2
3.7
3.70
Device holder uncertainty
E.4.1
3.6
3.60
∞
Output power variation –SAR
drift measurement
6.6.2
√3
2.89
∞
Phantom uncertainty
(shape and thickness
tolerances)
E.3.1
√3
2.31
∞
Liquid conductivity
- deviation from target values
E.3.2
√3
0.64
1.85
∞
Liquid conductivity
- measurement uncertainty
E.3.2
5.78
0.64
3.68
Liquid permittivity
- deviation from target values
E.3.3
√3
0.6
1.73
∞
Liquid permittivity
- measurement uncertainty
E.3.3
0.62
0.6
0.372
1
 Cp1/2
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
34 of 35
Combined standard
uncertainty
RSS
10.80
Expanded uncertainty
(95% CONFIDENCE
INTERVAL)
K=2
21.60
Table 6:
430
Measurement Uncertainty
Of
Calibration certificate
Please see the Appendix C
Photographs
Please see the Appendix D
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM170900938306
Page:
35 of 35
Appendix A: Detailed System Validation Results
Appendix B: Detailed Test Results
Appendix C: Calibration certificate
Appendix D: Photographs
---END---
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic
format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability,
indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the
limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the
transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are
retained for 30 days only
Download: BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Mirror Download [FCC.gov]BC03 Portable Media Console for Children RF Exposure Info SZEM170900938306x birde pty ltd
Document ID3774065
Application IDuuJvNgHeNNQYHvNd6xRgKw==
Document DescriptionRF Exposure Info
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeRF Exposure Info
Display FormatAdobe Acrobat PDF - pdf
Filesize87.55kB (1094361 bits)
Date Submitted2018-03-08 00:00:00
Date Available2018-03-08 00:00:00
Creation Date2018-02-07 14:45:55
Producing SoftwareGPL Ghostscript 8.64
Document Lastmod2018-02-07 06:45:58
Document TitleSZEM170900938306x
Document CreatorPScript5.dll Version 5.2.2
Document Author: yuxiu_yang

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Page Count                      : 35
Create Date                     : 2018:02:07 14:45:55+08:00
Title                           : Microsoft Word - SZEM170900938306.docx
Producer                        : GPL Ghostscript 8.64
Author                          : yuxiu_yang
Creator                         : PScript5.dll Version 5.2.2
Modify Date                     : 2018:02:07 06:45:58Z