FCC ID 2APAE-IPAM400
IPAM
by BARIX
Grantee Code: 2APAE Product Code: IPAM400
Latest application date: 2018-04-18
FCC ID Device Details
Operating Frequencies
| Frequency Range | Application Purpose | Final Action Date |
|---|---|---|
| 2412-2462 MHz | Original Equipment | 2018-04-18 |
Exhibits
| Document | Type | Available | File |
|---|---|---|---|
| Users manual | Users Manual | 2018-06-02 | PDF 1.1 MB |
| Internal photo | Internal Photos | 2018-06-02 | PDF 565.9 KB |
| External photo | External Photos | 2018-06-02 | PDF 257.7 KB |
| Label | ID Label/Location Info | 2018-04-18 | PDF 219 KB |
| Test setup photo | Test Setup Photos | 2018-06-02 | PDF 289.1 KB |
| Test Report | Test Report | 2018-04-18 | PDF 2 MB |
| Authorization Letter | Cover Letter(s) | 2018-04-18 | PDF 107.8 KB |
| Confidentiality request letter | Cover Letter(s) | 2018-04-18 | PDF 229.9 KB |
| MPE | RF Exposure Info | 2018-04-18 | PDF 209.4 KB |
| Block diagram Metadata only | Block Diagram | PDF 1.3 MB | |
| Schematics Metadata only | Schematics | PDF 388.1 KB | |
| Operational Description Metadata only | Operational Description | PDF 94.8 KB |
Application Information
| Application ID | 35K/KlUXstQNA4fD1RPfPQ== |
|---|---|
| Final Action Date | 2018-04-18 |
| Application Purpose | Original Equipment |
| Applicant FRN | 0027345305 |
| Model | IPAM400 |
| Frequency Range | 2412-2462 MHz |
| Equipment Class | DTS - Digital Transmission System |
| Device Description | IPAM |
| Responsible Party | Mario Almeida, mario.almeida@barix.com  , +41 43 43322 11 |
| Technical Contact | Eileen Liu, Shenzhen NTEK Testing Technology Co., Ltd., liudun@ntek.org.cn  , 86-755-61159378 |
| Test Firm | Alex Li, Shenzhen NTEK Testing Technology Co., Ltd., certification@ntek.org.cn , +86-755-6115-9384 |
| TCB Email | certification@micomlabs.com  |
| TCB Scope | A4: UNII devices & low power transmitters using spread spectrum techniques |
| Short-Term Confidentiality | No |
| Short-Term Confidentiality Date | 06/02/2018 |
| Long-Term Confidentiality | Yes |
| Grant Deferral | No |
| Modular Equipment | Does not apply |
| Composite Device | No |
| Composite Part | No |
| Cognitive Radio | No |
| Authorization Waiver | No |
| Authorization Waiver Approved | No |
| Section 5301 Certification | Yes |
| Related OET Knowledge DataBase Inquiry | No |
| Grant Comments | Output power listed is conducted power. The antenna used with this transmitter must be installed to provide a minimum separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. End-users must be provided with operating procedures for satisfying RF exposure compliance. This device contains 20 MHz signal bandwidth. |
Applications
| Application ID | Date | Purpose |
|---|---|---|
| 35K/KlUXstQNA4fD1RPfPQ== | 2018-04-18 | Original Equipment |
Grants
TCB Grant - Application 35K/KlUXstQNA4fD1RPfPQ==
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
MiCOM Labs 575 Boulder Court Pleasanton, CA 94566 |
Date of Grant: 04/18/2018 Application Dated: 04/18/2018 |
| BARIX |
| Barix AG, Ringstrasse 15A |
| 8600 Dubendorf, Switzerland |
| Dubendorf, Switzerland |
| Attention: Mario Almeida |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | 2APAE-IPAM400 |
| Name of Grantee: | BARIX |
| Equipment Class: | Digital Transmission System |
| Notes: | IPAM |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 20 | 15C | 2412.0 - 2462.0 | 0.0338 |
| Output power listed is conducted power. The antenna used with this transmitter must be installed to provide a minimum separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. End-users must be provided with operating procedures for satisfying RF exposure compliance. This device contains 20 MHz signal bandwidth. |
| 20: | All electrical and mechanical devices employed for spurious radiation suppression, including any modifications made during certification testing, must be incorporated in each unit marketed. |
EAS Grant - Application 35K/KlUXstQNA4fD1RPfPQ==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
BARIX Barix AG, Ringstrasse 15A 8600 Dubendorf, Switzerland Dubendorf, Switzerland |
Date of Grant: 04/18/2018 Application Dated: 04/18/2018 |
| Attention: Mario Almeida |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | 2APAE-IPAM400 |
| Name of Grantee: | BARIX |
| Equipment Class: | Digital Transmission System |
| Notes: | IPAM |
| Modular Type: | Does not apply |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 20 | 15C | 2412.0 - 2462.0 | 0.0338 |
| Output power listed is conducted power. The antenna used with this transmitter must be installed to provide a minimum separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. End-users must be provided with operating procedures for satisfying RF exposure compliance. This device contains 20 MHz signal bandwidth. |
| 20: | All electrical and mechanical devices employed for spurious radiation suppression, including any modifications made during certification testing, must be incorporated in each unit marketed. |
| Mail To: |