PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED

PCTECH ELECTRONICS (SZ) CO.,LIMITED 2.4G Wireless Mouse

Page 1 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 2 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 3 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 4 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 5 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 6 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 7 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 8 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 9 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 10 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 11 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 12 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 13 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 14 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 15 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 16 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 17 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 18 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 19 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 20 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 21 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 22 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 23 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 24 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 25 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 26 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 27 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 28 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 29 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Page 30 of PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
FCC TEST REPORT
FOR
PCTECH ELECTRONICS (SZ) CO.,LIMITED
2.4G Wireless Mouse
Test Model: PC-RC611
Additional Model No.: MEAM006
PCTECH ELECTRONICS (SZ) CO.,LIMITED
Building-67,FuYuan street FengHuang FuYong Town BaoAn District
ShenZhen City China
Prepared for
Address
Prepared by
Address
Tel
Fax
Web
Mail
Shenzhen LCS Compliance Testing Laboratory Ltd
1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue, Bao’an
District, Shenzhen, Guangdong, China
(+86)755-82591330
(+86)755-82591332
www.LCS-cert.com
webmaster@LCS-cert.com
Date of receipt of test sample
Number of tested samples
Sample number
Date of Test
Date of Report
September 25, 2018
Prototype
September 25, 2018~ November 1, 2018
November 1, 2018
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 1 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
FCC TEST REPORT
FCC CFR 47 PART 15 C(15.249)
Report Reference No. ................. : LCS180925005AE
Date of Issue................................... : November 1, 2018
Testing Laboratory Name ............ : Shenzhen LCS Compliance Testing Laboratory Ltd.
Address ........................................... :
Testing Location/ Procedure ..........
1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue,
Bao’an District, Shenzhen, Guangdong, China
Full application of Harmonised standards
■
Partial application of Harmonised standards □
Other standard testing method □
Applicant’s Name ......................... : PCTECH ELECTRONICS (SZ) CO.,LIMITED
Address ........................................... :
Building-67,FuYuan street FengHuang FuYong Town BaoAn
District ShenZhen City China
Test Specification
Standard ......................................... : FCC CFR 47 PART 15 C(15.249) / ANSI C63.10: 2013
Test Report Form No. ..................... : LCSEMC-1.0
TRF Originator ................................ : Shenzhen LCS Compliance Testing Laboratory Ltd.
Master TRF ..................................... : Dated 2011-03
Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the
Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of
the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not
assume liability for damages resulting from the reader's interpretation of the reproduced material due to
its placement and context.
Test Item Description. .................. : 2.4G Wireless Mouse
Trade Mark ..................................... :
Test Model ...................................... : PC-RC611
Ratings ............................................ :
DC 3.7V by battery (400mAh)
Recharge Voltage: DC 5V
Result ........................................... : Positive
Compiled by:
Supervised by:
Approved by:
Dick Su/ File administrators
Calvin Weng/ Technique principal
Gavin Liang/ Manager
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 2 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
FCC -- TEST REPORT
Test Report No. :
LCS180925005AE
November 1, 2018
Date of issue
Test Model..............................
: PC-RC611
EUT.........................................
: 2.4G Wireless Mouse
Applicant...............................
: PCTECH ELECTRONICS (SZ) CO.,LIMITED
Address..................................
Telephone..........................
: /
Fax.....................................
: /
Manufacturer.....................
: PCTECH ELECTRONICS (SZ) CO.,LIMITED
Address..............................
Telephone..........................
: /
Fax.....................................
: /
Factory..............................
: PCTECH ELECTRONICS (SZ) CO.,LIMITED
Address..............................
Telephone..........................
: /
Fax.....................................
: /
Test Result
Building-67,FuYuan street FengHuang FuYong Town BaoAn
District ShenZhen City China
Building-67,FuYuan street FengHuang FuYong Town BaoAn
District ShenZhen City China
Building-67,FuYuan street FengHuang FuYong Town BaoAn
District ShenZhen City China
Positive
The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test
laboratory.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 3 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
Revision History
Revision
000
Issue Date
November 1, 2018
Revisions
Initial Issue
Revised By
Gavin Liang
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
TABLE OF CONTENTS
1. GENERAL INFORMATION ................................................................................................................ 6
1.1.
1.2.
1.3.
1.4.
1.5.
1.6.
1.7.
1.8.
Description of Device (EUT) ................................................................................................................ 6
Support Equipment List ........................................................................................................................ 6
External I/O ............................................................................................................................................. 6
Description of Test Facility ................................................................................................................... 6
Statement of the Measurement Uncertainty...................................................................................... 7
Measurement Uncertainty .................................................................................................................... 7
Description of Test Modes ................................................................................................................... 7
Channel List & Frequency .................................................................................................................... 8
2. TEST METHODOLOGY ...................................................................................................................... 9
2.1 EUT Configuration ....................................................................................................................................... 9
2.2. EUT Exercise ............................................................................................................................................... 9
2.3. General Test Procedures........................................................................................................................... 9
3. SYSTEM TEST CONFIGURATION ................................................................................................ 10
3.1. Justification ................................................................................................................................................ 10
3.2. EUT Exercise Software ............................................................................................................................ 10
3.3. Special Accessories.................................................................................................................................. 10
3.4. Block Diagram/Schematics ..................................................................................................................... 10
3.5. Equipment Modifications .......................................................................................................................... 10
3.6. Test Setup .................................................................................................................................................. 10
4. SUMMARY OF TEST RESULTS ..................................................................................................... 11
5. TEST RESULT .................................................................................................................................... 12
5.1. Radiated Emission Measurement........................................................................................................... 12
5.2. AC Power Line Conducted Emissions ................................................................................................... 21
5.4. 99% Occupied Bandwidth and 20 dB Bandwidth Measurement ....................................................... 26
5.5. ANTENNA REQUIREMENT .................................................................................................................... 28
6. LIST OF MEASURING EQUIPMENT ............................................................................................. 29
7. TEST SETUP PHOTOGRAPHS OF EUT ...................................................................................... 30
8. EXTERIOR PHOTOGRAPHS OF EUT .......................................................................................... 30
9. INTERIOR PHOTOGRAPHS OF EUT ............................................................................................ 30
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 5 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
1. GENERAL INFORMATION
1.1. Description of Device (EUT)
EUT
: 2.4G Wireless Mouse
Model Number
: PC-RC611, MEAM006
PCB board, structure and internal of these model(s) are the same, So
no additional models were tested.
Model Declaration
Test Model
: PC-RC611
Power Supply
Hardware Version
: A11
Software Version
2.4GHz Function
: AF
Frequency Range
2.4G Operation
frequency (MHz)
Channel Number
Modulation Type
: 2402MHz-2480MHz
2402, 2404, 2410, 2412, 2418, 2428, 2432, 2440, 2448, 2450, 2454,
2464, 2468, 2470, 2476, 2480
: 16 channels (Support hopping technology)
: GFSK
Antenna Description
: PCB antenna, 0dBi (Max.)
DC 3.7V by battery (400mAh)
Recharge Voltage: DC 5V
1.2. Support Equipment List
Manufacturer
Description
Model
Serial Number
Certificate
--
--
--
--
--
1.3. External I/O
I/O Port Description
Micro USB
Quantity
Cable
N/A
1.4. Description of Test Facility
FCC Registration Number. is 254912.
Industry Canada Registration Number. is 9642A-1.
ESMD Registration Number. is ARCB0108.
UL Registration Number. is 100571-492.
TUV SUD Registration Number. is SCN1081.
TUV RH Registration Number. is UA 50296516-001
NVLAP Registration Code is 600167-0.
The 3m-Semi anechoic test site fulfils CISPR 16-1-4 according to ANSI C63.4:2014 and CISPR
16-1-4:2010 SVSWR requirement for radiated emission above 1GHz.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 6 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
1.5. Statement of the Measurement Uncertainty
The data and results referenced in this document are true and accurate. The reader is cautioned that
there may be errors within the calibration limits of the equipment and facilities. The measurement
uncertainty was calculated for all measurements listed in this test report acc. To CISPR 16 – 4
“Specification for radio disturbance and immunity measuring apparatus and methods – Part 4:
Uncertainty in EMC Measurements” and is documented in the LCS quality system acc. To DIN EN
ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may
result in additional deviation. The manufacturer has the sole responsibility of continued compliance of
the device.
1.6. Measurement Uncertainty
Test Item
Radiation Uncertainty
Conduction Uncertainty :
Power disturbance
Frequency Range
9KHz~30MHz
30MHz~200MHz
200MHz~1000MHz
1GHz~26.5GHz
26.5GHz~40GHz
150kHz~30MHz
30MHz~300MHz
Uncertainty
±3.10dB
±2.96dB
±3.10dB
±3.80dB
±3.90dB
±1.63dB
±1.60dB
Note
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1). This uncertainty represents an expanded uncertainty expressed at approximately the 95%
confidence level using a coverage factor of k=2.
1.7. Description of Test Modes
The EUT operates in the unlicensed ISM band at 2.4GHz. The following operating modes were
applied for the related test items.
All test modes were tested, only the result of the worst case was recorded in the report.
It was pre-tested on the positioned of each 3 axis. The worst case was found positioned on X-plane.
Mode of Operations
GFSK
Frequency Range
(MHz)
2402
2440
2480
For Conducted Emission
Test Mode
Data Rate
(Mbps)
TX Mode
For Radiated Emission
Test Mode
TX Mode
Worst-case mode and channel used for 150 KHz-30 MHz power line conducted emissions was the
mode and channel with the highest output power, that was determined to be TX-2428MHz.
Worst-case mode and channel used for 9 KHz-1000 MHz radiated emissions was the mode and
channel with the highest output power, that was determined to be TX-2428MHz.
AC conducted emission pre-test at both at AC 120V/60Hz and AC 240V/50Hz modes, recorded
worst case.
AC conducted emission pre-test at charger from PC modes, recorded worst case.
***Note: Using a temporary antenna connector for the EUT when the conducted measurements are
performed.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 7 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
1.8. Channel List & Frequency
Channel
Frequency(MHz)
2402
2404
2410
2412
2418
2428
2432
2440
Channel
10
11
12
13
14
15
16
Frequency(MHz)
2448
2450
2454
2464
2468
2470
2476
2480
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 8 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
2. TEST METHODOLOGY
All measurements contained in this report were conducted with ANSI C63.10-2013, American National
Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices.
The radiated testing was performed at an antenna-to-EUT distance of 3 meters. All radiated and
conducted emissions measurement was performed at Shenzhen LCS Compliance Testing Laboratory Ltd.
2.1 EUT Configuration
The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions
requirement and operating in a manner that intends to maximize its emission characteristics in a
continuous normal application.
2.2. EUT Exercise
The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the
measurements.
According to its specifications, the EUT must comply with the requirements of the Section 15.203, 15.205,
15.207, 15.209 and 15.249 under the FCC Rules Part 15 Subpart C.
2.3. General Test Procedures
2.3.1 Conducted Emissions
According to the requirements in Section 6.2 of ANSI C63.10: 2013, AC power-line conducted emissions
shall be measured in the frequency range between 0.15 MHz and 30MHz using Quasi-peak and average
detector modes.
2.3.2 Radiated Emissions
The EUT is placed on a turn table and the turntable shall rotate 360 degrees to determine the position of
maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to
find out the highest emission. And also, each emission was to be maximized by changing the polarization
of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory
radiated emission measurements were made according to the requirements in Section 6.3 of ANSI
C63.10: 2013.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 9 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
3. SYSTEM TEST CONFIGURATION
3.1. Justification
The system was configured for testing in a continuous transmit condition.
Using four samples to test, each sample was set up separately for a single transmitter frequency point,
which was automatically launched
3.2. EUT Exercise Software
N/A
3.3. Special Accessories
No.
Equipment
Manufacturer
Model No.
Serial No.
Length
PC
Power adapter
Lenovo
Lenovo
B470
ADP-90DDB
1.00m
shielded/
unshielded
unshielded
Notes
DOC
DOC
3.4. Block Diagram/Schematics
Please refer to the related document
3.5. Equipment Modifications
Shenzhen LCS Compliance Testing Laboratory Ltd. has not done any modification on the EUT.
3.6. Test Setup
Please refer to the test setup photo.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 10 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
4. SUMMARY OF TEST RESULTS
Applied Standard: FCC Part 15 Subpart C;
FCC Rules
Description of Test
Antenna Requirements
§15.203
§15.207(a)
Power Line Conducted Emissions
§15.205(a), §15.209(a),
Radiated Emissions Measurement
§15.249(a), §15.249(c)
§15.205, §15.249(d)
Band Edges Measurement
§15.249, §15.215
99% and 20 dB Bandwidth
Result
Compliant
Compliant
Compliant
Compliant
Compliant
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 11 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
5. TEST RESULT
5.1. Radiated Emission Measurement
5.1.1. Standard Applicable
1). According to §15.249 (d) and RSS-210 B.10 (b): Emissions radiated outside of the specified
frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the
fundamental or to the general radiated emission limits in §15.209, whichever is the lesser attenuation.
Frequencies (MHz)
0.009~0.490
0.490~1.705
1.705~30.0
30~88
88~216
216~960
Above 960
Field Strength (microvolts/meter)
2400/F(KHz)
24000/F(KHz)
30
100
150
200
500
Measurement Distance (meters)
300
30
30
2). According to §15.249 (a) and RSS-210 B.10 (a): Except as provided in paragraph (b) of this
section, the field strength of emissions from intentional radiators operated within these frequency
bands shall comply with the following:
Fundamental
frequency
902-928 MHz
2400-2483.5 MHz
5725-5875 MHz
24.0-24.25 GHz
Field strength of fundamental
millivolts/meter
dBuV/m
50
94
50
94
50
94
250
108
Field strength of harmonics
microvolts/meter
dBuV/m
500
54
500
54
500
54
2500
68
As shown in §15.35(b), for frequencies above 1000 MHz, the field strength limits in paragraphs (a)
and (b) of this section are based on average limits. However, the peak field strength of any emission
shall not exceed the maximum permitted average limits specified above by more than 20 dB under
any condition of modulation. For point-to-point operation under paragraph (b) of this section, the peak
field strength shall not exceed 2500 millivolts/meter at 3 meters along the antenna azimuth.
5.1.2. Measuring Instruments and Setting
Please refer to equipment’s list in this report. The following table is the setting of spectrum analyzer and
receiver.
Spectrum Parameter
Attenuation
Start Frequency
Stop Frequency
RB / VB (Emission in restricted band)
RB / VB (Emission in non-restricted band)
Receiver Parameter
Attenuation
Start ~ Stop Frequency
Start ~ Stop Frequency
Start ~ Stop Frequency
Setting
Auto
1000 MHz
10th carrier harmonic
1MHz / 3MHz for Peak, 1 MHz / 10Hz for Average
1MHz / 3MHz for Peak, 1 MHz / 10Hz for Average
Setting
Auto
9kHz~150kHz / RB/VB 200Hz/1KHz for QP/Average
150kHz~30MHz / RB/VB 9kHz/30KHz for QP/Average
30MHz~1000MHz / RB/VB 120kHz/1MHz for QP
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 12 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
5.1.3. Test Procedures
1) Sequence of testing 9 kHz to 30 MHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or
described by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 0.8 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions.
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna height is 0.8 meter.
--- At each turntable position the analyzer sweeps with peak detection to find the maximum of all
emissions
Final measurement:
--- Identified emissions during the premeasurement the software maximizes by rotating the turntable
position (0° to 360°) and by rotating the elevation axes (0° to 360°).
--- The final measurement will be done in the position (turntable and elevation) causing the highest
emissions with QPK detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, correction factor,
margin to the limit and limit will be recorded. Also a plot with the graph of the premeasurement and
the limit will be stored.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 13 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
2) Sequence of testing 30 MHz to 1 GHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or
described by manufacturer.
--- If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground
plane.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height changes from 1 to 3 meter.
--- At each turntable position, antenna polarization and height the analyzer sweeps three times in
peak to find the maximum of all emissions.
Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software
maximize the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4
meter.
--- The final measurement will be done with QP detector with an EMI receiver.
--- The final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization,
turntable angle, correction factor, margin to the limit and limit will be recorded. Also a plot with the
graph of the premeasurement with marked maximum final measurements and the limit will be stored.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 14 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
3) Sequence of testing 1 GHz to 18 GHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or
described by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height scan range is 1 meter to 2.5 meter.
--- At each turntable position and antenna polarization the analyzer sweeps with peak detection to
find the maximum of all emissions.
Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software
maximize the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4
meter. This procedure is repeated for both antenna polarizations.
--- The final measurement will be done in the position (turntable, EUT-table and antenna polarization)
causing the highest emissions with Peak and Average detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, EUT-table position,
antenna polarization, correction factor, margin to the limit and limit will be recorded. Also a plot with
the graph of the premeasurement with marked maximum final measurements and the limit will be
stored.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 15 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
4) Sequence of testing above 18 GHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or
described by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 1 meter.
--- The EUT was set into operation.
Premeasurement:
--- The antenna is moved spherical over the EUT in different polarizations of the antenna.
Final measurement:
--- The final measurement will be performed at the position and antenna orientation for all detected
emissions that were found during the premeasurements with Peak and Average detector.
--- The final levels, frequency, measuring time, bandwidth, correction factor, margin to the limit and
limit will be recorded. Also a plot with the graph of the premeasurement and the limit will be stored.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 16 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
5.1.4. Test Setup Layout
Above 18 GHz shall be extrapolated to the specified distance using an extrapolation factor of 20
dB/decade form 3m to 1m.
Distance extrapolation factor = 20 log (specific distance [3m] / test distance [1m]) (dB);
Limit line = specific limits (dBuV) + distance extrapolation factor [6 dB].
5.1.5. EUT Operation during Test
The EUT was programmed to be in continuously transmitting mode.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 17 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
5.1.6. Results of Radiated Emissions (9 KHz~30MHz)
Temperature
Test Engineer
Humidity
Configurations
22.6℃
Wilson Hong
52.7%
Tx
Freq.
(MHz)
Level
(dBuV)
Over Limit
(dB)
Over Limit
(dB)
Remark
See Note
Note:
The amplitude of spurious emissions which are attenuated by more than 20 dB below the permissible
value has no need to be reported.
Distance extrapolation factor = 40 log (specific distance / test distance) (dB);
Limit line = specific limits (dBuV) + distance extrapolation factor.
5.1.7. Results of Radiated Emissions (30MHz~1GHz)
Temperature
Test Engineer
22.6℃
Wilson Hong
Humidity
Configurations
52.7%
Tx
Vertical
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 18 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
Horizontal
Note:
1). Pre-scan all modes and recorded the worst case results in this report (TX-Low Channel).
2) Emission level (dBuV/m) = 20 log Emission level (uV/m).
3). Corrected Reading: Antenna Factor + Cable Loss + Read Level - Preamp Factor = Level.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 19 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
5.1.8. Results for Radiated Emissions (Above 1GHz)
Frequency
(MHz)
2402
2402
Pol.
Freq.
MHz
Reading
dBuV
4804.00
4804.00
4804.00
4804.00
61.06
43.51
55.52
41.11
Frequency
(MHz)
2440
2440
Pol.
Freq.
MHz
Reading
dBuV
4880.00
4880.00
4880.00
4880.00
61.10
41.25
53.92
40.73
Frequency
(MHz)
2480
2480
Pol.
Freq.
MHz
Reading
dBuV
4960.00
4960.00
4960.00
4960.00
56.34
43.46
54.86
37.64
Field Strength of Fundamental (TX-2402MHz)
Measure Result
Measure Result
Peak Limit
(PK, dBuV/m)
(AVG, dBuV/m)
(dBuV/m)
86.27
75.94
114
81.36
71.17
114
Ant.
Fac
dB/m
32.14
32.14
32.21
32.21
Pre.
Fac
dB
34.12
34.12
34.19
34.19
Cab.
Los
dB
3.53
3.53
3.58
3.58
Pre.
Fac
dB
35.04
35.04
35.14
35.14
Cab.
Los
dB
3.94
3.94
3.98
3.98
Pre.
Fac
dB
35.14
35.14
35.14
35.14
Cab.
Los
dB
3.98
3.98
3.98
3.98
Pass
Pass
Limit
dBuV/m
Margin
dB
Remark
Pol.
62.61
45.06
57.12
42.71
74.00
54.00
74.00
54.00
-11.39
-8.94
-16.88
-11.29
Peak
Average
Peak
Average
Horizontal
Horizontal
Vertical
Vertical
AVG Limit
(dBuV/m)
94
94
Result
Pass
Pass
Measured
dBuV/m
Limit
dBuV/m
Margin
dB
Remark
Pol.
63.06
43.21
56.02
42.83
74.00
54.00
74.00
54.00
-10.94
-10.79
-17.98
-11.17
Peak
Average
Peak
Average
Horizontal
Horizontal
Vertical
Vertical
Field Strength of Fundamental (TX-2480MHz)
Measure Result
Measure Result
Peak Limit
(PK, dBuV/m)
(AVG, dBuV/m)
(dBuV/m)
88.67
77.62
114
84.15
72.59
114
Ant.
Fac
dB/m
33.26
33.26
33.26
33.26
Result
Measured
dBuV/m
Field Strength of Fundamental (TX-2440MHz)
Measure Result
Measure Result
Peak Limit
(PK, dBuV/m)
(AVG, dBuV/m)
(dBuV/m)
92.07
80.16
114
88.32
76.69
114
Ant.
Fac
dB/m
33.06
33.06
33.26
33.26
AVG Limit
(dBuV/m)
94
94
AVG Limit
(dBuV/m)
94
94
Result
Pass
Pass
Measured
dBuV/m
Limit
dBuV/m
Margin
dB
Remark
Pol.
58.44
45.56
56.96
39.74
74.00
54.00
74.00
54.00
-15.56
-8.44
-17.04
-14.26
Peak
Average
Peak
Average
Horizontal
Horizontal
Vertical
Vertical
Notes:
1. Measuring frequencies from 9 KHz~10th harmonic (ex. 26GHz), No emission found between lowest
internal used/generated frequency to 30MHz.
2. Radiated emissions measured in frequency range from 9 KHz~10th harmonic (ex. 26GHz) were made
with an instrument using Peak detector mode.
3. No emission was be recorded above 18GHz means the reading of emissions are attenuated more than
20dB below the permissible limits or the field strength is too small to be measured.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 20 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
5.2. AC Power Line Conducted Emissions
5.2.1. Standard Applicable
According to §15.207 (a) & RSS-Gen § 8.8: For an intentional radiator which is designed to be connected
to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power
line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed 250 microvolts
(The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50 MHz). The
limits at specific frequency range are listed as follows:
Limits (dBμV)
Quasi-peak
Average
66 to 56
56 to 46
56
46
60
50
Frequency Range
(MHz)
0.15 to 0.50
0.50 to 5
5 to 30
* Decreasing linearly with the logarithm of the frequency
5.2.2. Block Diagram of Test Setup
Vert. reference
plane
EMI receiver
EUT
LISN
Reference ground plane
5.2.3. Test Results
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 21 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
AC Conducted Emission of charge from PC mode @ AC 120V/60Hz @ GFSK (worst case)
Line
Neutral
***Note: Pre-scan all modes and recorded the worst case results in this report.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 22 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
5.3. Results for Band edge Testing
5.3.1 Standard Applicable
According to FCC §15.249 (d): Emissions radiated outside of the specified frequency bands, except for
harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general
radiated emission limits in §15.209, whichever is the lesser attenuation.
According to RSS-210 B.10 (b): Emissions radiated outside of the specified frequency bands, except for
harmonic emissions, shall be attenuated by at least 50 dB below the level of the fundamental emissions or
to the general field strength limits listed in RSS-Gen, whichever is less stringent.
5.3.2. Test Setup Layout
5.3.3. Measuring Instruments and Setting
Please refer to equipment list in this report. The following table is the setting of Spectrum Analyzer.
5.3.4. Test Procedures
According to ANSI C63.10:2013 Field Strength Approach (linear terms):
eirp = pt x gt = (E x d)2/30
Where:
pt = transmitter output power in watts, 
gt = numeric gain of the transmitting antenna (unitless), 
E = electric field strength in V/m, 
d = measurement distance in meters (m).
erp = eirp/1.64 = (E x d)2/(30 x 1.64)
Where all terms are as previously defined.
1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal
from an external generator.
2. Remove the antenna from the EUT and then connect to a low loss RF cable from the antenna port to
an EMI test receiver, then turn on the EUT and make it operate in transmitting mode. Then set it to
Low Channel and High Channel within its operating range, and make sure the instrument is operated
in its linear range.
3. Set both RBW and VBW of spectrum analyzer for Radiated emissions restricted band RBW=1MHz,
VBW=3MHz for peak detector and RBW=1MHz, VBW=1/B for Peak detector.
4. Measure the highest amplitude appearing on spectral display and set it as a reference level. Plot the
graph with marking the highest point and edge frequency.
5. Repeat above procedures until all measured frequencies were complete.
6. Measure the conducted output power (in dBm) using the detector specified by the appropriate
regulatory agency for guidance regarding measurement procedures for determining quasi-peak, peak,
and average conducted output power, respectively).
7. Add the maximum transmit antenna gain (in dBi) to the measured output power level to determine the
EIRP level (see 12.2.5 for guidance on determining the applicable antenna gain)
8. Add the appropriate maximum ground reflection factor to the EIRP level (6 dB for frequencies ≤ 30
MHz, 4.7 dB for frequencies between 30 MHz and 1000 MHz, inclusive and 0 dB for frequencies >
1000 MHz).
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 23 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
9. For devices with multiple antenna-ports, measure the power of each individual chain and sum the
EIRP of all chains in linear terms (e.g., Watts, mW).
10. Compare the resultant electric field strength level to the applicable regulatory limit.
11. Perform radiated spurious emission test duress until all measured frequencies were complete.
5.3.5. Measuring Instruments and Setting
Frequency
(MHz)
Conducted
Power
(dBm)
Antenna
Gain
(dBi)
2310.000
2390.000
2483.500
2500.000
-48.932
-48.656
-48.516
-47.530
2.0
2.0
2.0
2.0
GFSK
Ground
Reflection
Factor
(dB)
0.0
0.0
0.0
0.0
Covert
Radiated E
Level At 3m
(dBuV/m)
48.33
48.60
48.74
49.73
Detector
Limit
(dBuV/m)
Verdict
Peak
Peak
Peak
Peak
74.00
74.00
74.00
74.00
PASS
PASS
PASS
PASS
Remark:
1. The other emission levels were very low against the limit.
2. The average measurement was not performed when the peak measured data under the limit of
average detection.
3. Detector AV is setting spectrum/receiver. RBW=1MHz/VBW=10Hz/Sweep time=Auto/Detector=Peak;
4. Since the out-of-band characteristics of the EUT transmit antenna will often be unknown, the use of a
conservative antenna gain value is necessary. Thus, when determining the EIRP based on the
measured conducted power, the upper bound on antenna gain for a device with a single RF output
shall be selected as the maximum in-band gain of the antenna across all operating bands, or 2 dBi,
whichever is greater. However, for devices that operate in multiple frequency bands while using the
same transmit antenna, the highest gain of the antenna within the operating band nearest in frequency
to the restricted band emission being measured may be used in lieu of the overall highest gain when
the emission is at a frequency that is within 20 percent of the nearest band edge frequency, but in no
case shall a value less than 2 dBi be used.
5. Please refer to following test plots;
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 24 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
Restrict-Band Band-edge measurements for radiated emissions
GFSK
GFSK
2402 MHz – Peak
2480 MHz – Peak
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 25 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
5.4. 99% Occupied Bandwidth and 20 dB Bandwidth Measurement
5.4.1. Standard Applicable
According to § 2.1049 and RSS-Gen section 6.7 “The occupied bandwidth or the “99% emission
bandwidth” is defined as the frequency range between two points, one above and the other below the
carrier frequency, within which 99% of the total transmitted power of the fundamental transmitted emission
is contained. The occupied bandwidth shall be reported for all equipment in addition to the specified
bandwidth required in the applicable RSSs.”
In some cases, the “x dB bandwidth” is required, which is defined as the frequency range between two
points, one at the lowest frequency below and one at the highest frequency above the carrier frequency, at
which the maximum power level of the transmitted emission is attenuated x dB below the maximum in
band power level of the modulated signal, where the two points are on the outskirts of the in-band
emission.
5.4.2. Block Diagram of Test Setup
5.4.3. Test Procedure
Use the following spectrum analyzer settings:
Span = 3MHz
RBW = 30 KHz
VBW = 100 KHz
Sweep = auto
Detector function = peak
Trace = max hold
The EUT should be transmitting at its maximum data rate. Allow the trace to stabilize. Use the
marker-to-peak function to set the marker to the peak of the emission. Use the marker-delta function to
measure 20 dB down one side of the emission. Reset the marker-delta function, and move the marker to
the other side of the emission, until it is (as close as possible to) even with the reference marker level. The
marker-delta reading at this point is the 20 dB bandwidth of the emission. If this value varies with different
modes of operation (e.g., data rate, modulation format, etc.), repeat this test for each variation. The limit is
specified in one of the subparagraphs of this Section. Submit this plot(s).
5.4.4. Test Results
Test Frequency
(MHz)
2402
2440
2480
Test Result of 99% and 20dB Bandwidth Measurement
20dB Bandwidth
99% Bandwidth
(MHz)
(MHz)
2.034
2.041
2.059
1.9877
2.0044
2.0239
Limit
(MHz)
Non-Specified
Non-Specified
Non-Specified
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 26 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
Remark:
1. Test results including cable loss;
2. Please refer following test plots;
20dB Bandwidth and 99% Bandwidth
GFSK
GFSK
2402 MHz
GFSK
2440 MHz
2480 MHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 27 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
5.5. ANTENNA REQUIREMENT
5.5.1. Standard Applicable
According to § 15.203 and RSS-Gen, an intentional radiator shall be designed to ensure that no antenna
other than that furnished by the responsible party shall be used with the device. The use of a permanently
attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be
considered sufficient to comply with the provisions of this section. The manufacturer may design the unit
so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical
connector is prohibited.
5.5.2. Antenna Connected Construction
The directional gains of antenna used for transmitting is 0dBi, and the antenna is an Internal antenna
connect to PCB board and no consideration of replacement. Please see EUT photo for details.
5.5.3 Result
Compliance.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 28 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
6. List of Measuring Equipment
Item Equipment
Manufacturer
Model No.
Serial No.
Last Cal.
Next Cal.
Power Meter
R&S
NRVS
100444
2018-06-16
2019-06-15
Power Sensor
R&S
NRV-Z81
100458
2018-06-16
2019-06-15
Power Sensor
R&S
NRV-Z32
10057
2018-06-16
2019-06-15
ESA-E SERIES
Agilent
SPECTRUM ANALYZER
E4407B
MY41440754
2017-11-17
2018-11-16
MXA Signal Analyzer
N9020A
MY49100040
2018-06-16
2019-06-15
SPECTRUM ANALYZER R&S
FSP
100503
2018-06-16
2019-06-15
3m Semi Anechoic
Chamber
SIDT FRANKONIA
SAC-3M
03CH03-HY
2018-06-16
2019-06-15
Positioning Controller
MF
MF-7082
2018-06-16
2019-06-15
EMI Test Software
AUDIX
E3
N/A
N/A
N/A
10
EMI Test Receiver
R&S
ESR 7
101181
2018-06-16
2019-06-15
11
AMPLIFIER
QuieTek
QTK-A2525G
CHM10809065
2017-11-17
2018-11-16
12
Active Loop Antenna
SCHWARZBECK
FMZB 1519B
00005
2018-06-22
2019-06-21
13
By-log Antenna
SCHWARZBECK
VULB9163
9163-470
2018-05-02
2019-05-01
14
Horn Antenna
SCHWARZBECK
BBHA 9120 D
9120D-1925
2018-07-02
2019-07-01
15
Broadband Horn Antenna SCHWARZBECK
BBHA 9170
791
2017-09-21
2020-09-20
16
Broadband Preamplifier
SCHWARZBECK
BBV 9719
9719-025
2017-09-21
2020-09-20
17
RF Cable-R03m
Jye Bao
RG142
CB021
2018-06-16
2019-06-15
18
RF Cable-HIGH
SUHNER
SUCOFLEX 106
03CH03-HY
2018-06-16
2019-06-15
19
TEST RECEIVER
R&S
ESCI
101142
2018-06-16
2019-06-15
20
RF Cable-CON
UTIFLEX
3102-26886-4
CB049
2018-06-16
2019-06-15
21
10dB Attenuator
SCHWARZBECK
MTS-IMP136
261115-001-0032 2018-06-16
2019-06-15
22
Artificial Mains
R&S
ENV216
101288
2018-06-16
2019-06-15
23
RF Control Unit
JS Tonscend
Corporation
JS0806-2
178060073
2018-10-27
2019-10-26
24
JS1120-3 BT/WIFI Test
Software
JS Tonscend
Corporation
JS1120-3
N/A
N/A
Agilent
Note: All equipment is calibrated through GUANGZHOU LISAI CALIBRATION AND TEST CO.,LTD.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 29 of 30
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.
FCC ID: 2ARII-PC-RC611
Report No.:LCS180925005AE
7. TEST SETUP PHOTOGRAPHS OF EUT
Please refer to separated files for Test Setup Photos of the EUT.
8. EXTERIOR PHOTOGRAPHS OF EUT
Please refer to separated files for External Photos of the EUT.
9. INTERIOR PHOTOGRAPHS OF EUT
Please refer to separated files for Internal Photos of the EUT.
----------------THE END OF TEST REPORT---------------
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 30 of 30
Download: PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Mirror Download [FCC.gov]PC-RC611 2.4G Wireless Mouse Test Report Shenzhen Sunspring Electronics Co., Ltd. PCTECH ELECTRONICS (SZ) CO.,LIMITED
Document ID4057809
Application IDNo1EX79aZm8VJKK4u+4HXw==
Document DescriptionTest Report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize65.93kB (824165 bits)
Date Submitted2018-11-02 00:00:00
Date Available2018-11-02 00:00:00
Creation Date2018-11-01 21:05:32
Producing SoftwareAdobe PDF Library 11.0
Document Lastmod2018-11-01 21:05:40
Document TitleShenzhen Sunspring Electronics Co., Ltd.
Document CreatorAcrobat PDFMaker 11 for Word
Document Author: Violet Wang

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Violet Wang
Comments                        : CG107C
Company                         : AUDIX
Create Date                     : 2018:11:01 21:05:32+08:00
Keywords                        : OJWCG107C
Modify Date                     : 2018:11:01 21:05:40+08:00
Source Modified                 : D:20181101130509
Subject                         : Keyboard
Language                        : EN-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2018:11:01 21:05:40+08:00
Creator Tool                    : Acrobat PDFMaker 11 for Word
Document ID                     : uuid:0ef575fc-5d7e-4343-babb-257d20d3dd69
Instance ID                     : uuid:c5954f84-6d6a-416d-9657-7cac000c592d
Format                          : application/pdf
Title                           : Shenzhen Sunspring Electronics Co., Ltd.
Description                     : Keyboard
Creator                         : Violet Wang
Producer                        : Adobe PDF Library 11.0
Headline                        : Keyboard
Page Layout                     : OneColumn
Page Count                      : 30