MWF82S01 802.11bgn module Cover Letter Modular Approval Request (per DA 00-1407) PTCOM Technology .

PTCOM Technology . 802.11bgn module

Page 1 of MWF82S01 802.11bgn module Cover Letter Modular Approval Request (per DA 00-1407) PTCOM Technology .
Page 2 of MWF82S01 802.11bgn module Cover Letter Modular Approval Request (per DA 00-1407) PTCOM Technology .

RF_734_02
04 April 16
Modular Approval Request FCC (KDB 996369 D01 & Part 15.212)
FCC ID: 2ARUV-MWF82S01
Items to be covered by Single modular transmitters.
1. The modular transmitter must have its own RF shielding.
2.
3.
The modular transmitter must have buffered modulation/data inputs (if such inputs
are provided) to ensure that the module will comply with Part 15 requirements
under conditions of excessive data rates or over-modulation.
The modular transmitter must have its own power supply regulation.
4.
The modular transmitter must comply with the antenna requirements of Section
15.203 and 15.204(b)(c). The antenna must either be permanently attached or
employ a “unique” antenna coupler (at all connections between the module and the
antenna, including the cable).
5.
The modular transmitter must be tested in a stand-alone configuration, i.e., the
module must not be inside another device during testing. This is intended to
demonstrate that the module is capable of complying with Part 15 emission limits
regardless of the device into which it is eventually installed.
6. The modular transmitter must be equipped with either a permanently affixed label
or must be capable of electronically displaying its FCC identification number in
accordance with 15.212 (a)(1)(vi)(A) / (B).
7. The modular transmitter must comply with any specific rule or operating
requirements applicable to the transmitter and the manufacturer must provide
adequate instructions along with the module to explain any such requirements. A
copy of these instructions must be included in the application for equipment
authorization. For example, there are very strict operational and timing
requirements that must be met before a transmitter is authorized for operation under
Section 15.231. For instance, data transmission is prohibited, except for operation
under Section 15.231(e), in which case there are separate field strength level and
timing requirements. Compliance with these requirements must be assured.
8.
The modular transmitter must comply with any applicable RF exposure
requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and
specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and
15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices
perform routine environmental evaluation for RF Exposure to demonstrate
compliance. In addition, spread spectrum transmitters operating under Section
15.247 are required to address RF Exposure compliance. Modular transmitters
approved under other Sections of Part 15, when necessary, may also need to
address certain RF Exposure concerns, typically by providing specific
installation and operating instructions for users, installers and other interested
parties to ensure compliance.
Answer from applicant
The modular has a shielding
Case. Please refer to EUT
Photo.
The component number is
MT7682
The component number is
MT7682
Antenna Connectors are NA.
And no external amplifier will
be used with this modular.
This modular is tested under
stand-alone configuration.
Please refer to Test setup
photo.
The modular transmitter is
labeled with its own FCC ID
number. Please refer to label
sample and label location.
The modular complies with
this requirement. Please refer
to user manual.
The device complies with this
requirement. Please refer to
RF exposure report.
RF_734_02
04 April 16
Items to be covered by Split modular transmitters.
1. The modular transmitter must comply with all requirements of a single modular
transmitter except for items (1) & (5) of the above single modular approval
requirements.
2.
Only the radio front end must be shielded. The physical crystal and tuning
capacitors may be located external to the shielded radio elements. The interface
between the split sections of the modular system must be digital with a minimum
signalling amplitude of 150 mV peak-to-peak.
3.
Control information and other data may be exchanged between the transmitter
control elements and radio front end.
4.
The sections of a split modular transmitter must be tested installed in a host
device(s) similar to that which is representative of the platform(s) intended for use.
5.
Manufacturers must ensure that only transmitter control elements and radio front
end components that have been approved together are capable of operating together.
The transmitter module must not operate unless it has verified that the installed
transmitter control elements and radio front end have been authorized together.
Manufacturers may use means including, but not limited to, coding in hardware and
electronic signatures in software to meet these requirements, and must describe the
methods in their application for equipment authorization.
Answer from applicant
Note: A limited modular approval (LMA) may be granted for single or split modular transmitters
that comply partially with the requirements above.
Name and surname of applicant (or authorized representative): __________________
Date: ___28 January 2019____
Signature: ___________________________
Download: MWF82S01 802.11bgn module Cover Letter Modular Approval Request (per DA 00-1407) PTCOM Technology .
Mirror Download [FCC.gov]MWF82S01 802.11bgn module Cover Letter Modular Approval Request (per DA 00-1407) PTCOM Technology .
Document ID4151364
Application IDthJ7NkKDjpNqmlpH6/CuEQ==
Document DescriptionModular approval letter
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeCover Letter(s)
Display FormatAdobe Acrobat PDF - pdf
Filesize16.68kB (208535 bits)
Date Submitted2019-01-30 00:00:00
Date Available2019-01-31 00:00:00
Creation Date2019-01-28 14:42:36
Producing SoftwareMicrosoft® Word 2010
Document Lastmod2019-01-28 14:42:49
Document TitleModular Approval Request (per DA 00-1407)
Document CreatorMicrosoft® Word 2010
Document Author: bvos

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : bvos
Create Date                     : 2019:01:28 14:42:36+08:00
Modify Date                     : 2019:01:28 14:42:49+08:00
Language                        : zh-TW
XMP Toolkit                     : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08
Format                          : application/pdf
Creator                         : bvos
Title                           : Modular Approval Request (per DA 00-1407)
Creator Tool                    : Microsoft® Word 2010
Metadata Date                   : 2019:01:28 14:42:49+08:00
Producer                        : Microsoft® Word 2010
Document ID                     : uuid:8650907b-9900-4a59-bf57-c73a6562a1b0
Instance ID                     : uuid:953223d7-9278-426f-ac03-4071b222f74f
Page Count                      : 2