FCC ID 2ATKUAPW42
Communication Module
by AirPatrol OU
Grantee Code: 2ATKU Product Code: APW42
Latest application date: 2019-12-04
FCC ID Device Details
| FCC ID | 2ATKUAPW42 |
|---|---|
| Mirrors | fcc.id | gov | fccid.ai |
| Grantee Code | 2ATKU |
| Product Code | APW42 |
| Applicant Business | AirPatrol OU 🇪🇪 |
| Related Domains |  airpatrol.eu  liewenthal.ee |
| Equipment Class | Communication Module |
| Test Firm | UL International Germany GmbH |
Operating Frequencies
| Frequency Range | Application Purpose | Final Action Date |
|---|---|---|
| 2412-2462 MHz | Class II permissive change or modification of presently authorized equipment | 2019-12-04 |
| 2412-2462 MHz | Change in identification of presently authorized equipment. Original FCC ID: VPYLBYD Grant Date: 01/31/2014 | 2019-10-24 |
Exhibits
| Document | Type | Available | File |
|---|---|---|---|
| External Photos | External Photos | 2019-10-24 | PDF 408.2 KB |
| Label Info | ID Label/Location Info | 2019-10-24 | PDF 157.1 KB |
| Test Set Up | Test Setup Photos | 2019-12-04 | PDF 491.1 KB |
| Test Report | Test Report | 2019-12-04 | PDF 1 MB |
| Authorisation Letter | Cover Letter(s) | 2019-12-04 | PDF 295.7 KB |
| Class II PC Request | Cover Letter(s) | 2019-12-04 | PDF 1 MB |
| Authorisation Letter | Cover Letter(s) | 2019-10-24 | PDF 270.6 KB |
| New Equipment Certification Holder Letter | Cover Letter(s) | 2019-10-24 | PDF 238.2 KB |
| Original Equipment Certification Holder Letter | Cover Letter(s) | 2019-10-24 | PDF 26.6 KB |
| TCB Letter Labelling | Cover Letter(s) | 2019-10-24 | PDF 10.5 KB |
Application Information
| Application ID | GOWy4exlr6E0+Op/yBBDfA== |
|---|---|
| Final Action Date | 2019-12-04 |
| Application Purpose | Class II permissive change or modification of presently authorized equipment |
| Applicant FRN | 0028543965 |
| Model | APW42 |
| Frequency Range | 2412-2462 MHz |
| Equipment Class | DTS - Digital Transmission System |
| Device Description | Communication Module |
| Responsible Party | Daniel Dordett, CEO, daniel@airpatrol.eu , +372 545 33 777 |
| Technical Contact | Denry Aron, Liewenthal Electronics OU, denry.aron@liewenthal.ee , +372 628 3610 |
| Non-Technical Contact | Rainer Tamm, Liewenthal Electronics OU, rainer.tamm@liewenthal.ee , +372 628 3610 |
| Test Firm | Bernd Woerl, UL International Germany GmbH, bernd.woerl@ul.com  , 4971149002031 |
| TCB Email | certification@ul.com |
| TCB Scope | A4: UNII devices & low power transmitters using spread spectrum techniques |
| Short-Term Confidentiality | No |
| Long-Term Confidentiality | No |
| Grant Deferral | No |
| Modular Equipment | Limited Single Modular Approval |
| Composite Device | No |
| Composite Part | No |
| Cognitive Radio | No |
| Authorization Waiver | No |
| Authorization Waiver Approved | No |
| Section 5301 Certification | Yes |
| Related OET Knowledge DataBase Inquiry | No |
| Grant Comments | Limited Modular Approval. Output power listed is Conducted(Maximum peak). Separate evaluation must be required for any portable configuration. Host systems must provide regulated supply voltages to the module. When used in mobile applications, the antennas shown in this filing must be installed to provide a separation distance of at least 20 cm from all persons. Compliance of this device in all final host configurations is the responsibility of the Grantee. OEM integrators and end-users must be provided with specific information required to satisfy RF exposure compliance for the final host device. OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. The antenna of this device must not be co-located or used in conjunction with any other antenna or transmitter. OEM integrators must be provided with antenna installation instructions. This module can only be used with a host antenna circuit trace layout design in strict compliance with the OEM instructions provided. Additional host systems will require reassessment due to the lack of voltage regulation and use special test jig board. Class II Permissive Change for a change of antenna circuit trace layout design for a specific host product as described in the filing. |
Applications
| Application ID | Date | Purpose |
|---|---|---|
| GOWy4exlr6E0+Op/yBBDfA== | 2019-12-04 | Class II permissive change or modification of presently authorized equipment |
| yaHdEBRnNGhz0VTgkplH7g== | 2019-10-24 | Change in identification of presently authorized equipment. Original FCC ID: VPYLBYD Grant Date: 01/31/2014 |
Equipment Authorization
| Frequency | Output | Rules |
|---|---|---|
| 2412-2462 MHz | 0.2361000 | 15C |
Grants
TCB Grant - Application yaHdEBRnNGhz0VTgkplH7g==
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
UL International (UK) Ltd Unit 1 - 3 Horizon Kingsland Business Park Wade Road Basingstoke, RG24 8AH United Kingdom |
Date of Grant: 10/24/2019 Application Dated: 10/24/2019 |
| AirPatrol OU |
| Sihi 42 |
| Tallinn, 11622 Estonia |
| Attention: Daniel Dordett , CEO |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | 2ATKUAPW42 |
| Name of Grantee: | AirPatrol OU |
| Equipment Class: | Digital Transmission System |
| Notes: | Communication Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 2412.0 - 2462.0 | 0.2361 |
| Limited Modular Approval. Output power listed is Conducted(Maximum peak). Separate evaluation must be required for any portable configuration. Host systems must provide regulated supply voltages to the module. When used in mobile applications, the antennas shown in this filing must be installed to provide a separation distance of at least 20 cm from all persons. Compliance of this device in all final host configurations is the responsibility of the Grantee. OEM integrators and end-users must be provided with specific information required to satisfy RF exposure compliance for the final host device. OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. The antenna of this device must not be co-located or used in conjunction with any other antenna or transmitter. OEM integrators must be provided with antenna installation instructions. This module can only be used with a host antenna circuit trace layout design in strict compliance with the OEM instructions provided. Additional host systems will require reassessment due to the lack of voltage regulation and use special test jig board |
EAS Grant - Application yaHdEBRnNGhz0VTgkplH7g==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
AirPatrol OU Sihi 42 Tallinn, 11622 Estonia |
Date of Grant: 10/24/2019 Application Dated: 10/24/2019 |
| Attention: Daniel Dordett , CEO |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | 2ATKUAPW42 |
| Name of Grantee: | AirPatrol OU |
| Equipment Class: | Digital Transmission System |
| Notes: | Communication Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 2412.0 - 2462.0 | 0.2361 |
| Limited Modular Approval. Output power listed is Conducted(Maximum peak). Separate evaluation must be required for any portable configuration. Host systems must provide regulated supply voltages to the module. When used in mobile applications, the antennas shown in this filing must be installed to provide a separation distance of at least 20 cm from all persons. Compliance of this device in all final host configurations is the responsibility of the Grantee. OEM integrators and end-users must be provided with specific information required to satisfy RF exposure compliance for the final host device. OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. The antenna of this device must not be co-located or used in conjunction with any other antenna or transmitter. OEM integrators must be provided with antenna installation instructions. This module can only be used with a host antenna circuit trace layout design in strict compliance with the OEM instructions provided. Additional host systems will require reassessment due to the lack of voltage regulation and use special test jig board |
| Mail To: | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
UL International (UK) Ltd Unit 1 - 3 Horizon Kingsland Business Park Wade Road Basingstoke, RG24 8AH United Kingdom |
Date of Grant: 12/04/2019 Application Dated: 12/04/2019 |
| AirPatrol OU |
| Sihi 42 |
| Tallinn, 11622 Estonia |
| Attention: Daniel Dordett , CEO |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | 2ATKUAPW42 |
| Name of Grantee: | AirPatrol OU |
| Equipment Class: | Digital Transmission System |
| Notes: | Communication Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 2412.0 - 2462.0 | 0.2361 |
| Limited Modular Approval. Output power listed is Conducted(Maximum peak). Separate evaluation must be required for any portable configuration. Host systems must provide regulated supply voltages to the module. When used in mobile applications, the antennas shown in this filing must be installed to provide a separation distance of at least 20 cm from all persons. Compliance of this device in all final host configurations is the responsibility of the Grantee. OEM integrators and end-users must be provided with specific information required to satisfy RF exposure compliance for the final host device. OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. The antenna of this device must not be co-located or used in conjunction with any other antenna or transmitter. OEM integrators must be provided with antenna installation instructions. This module can only be used with a host antenna circuit trace layout design in strict compliance with the OEM instructions provided. Additional host systems will require reassessment due to the lack of voltage regulation and use special test jig board. Class II Permissive Change for a change of antenna circuit trace layout design for a specific host product as described in the filing. |
EAS Grant - Application GOWy4exlr6E0+Op/yBBDfA==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
AirPatrol OU Sihi 42 Tallinn, 11622 Estonia |
Date of Grant: 12/04/2019 Application Dated: 12/04/2019 |
| Attention: Daniel Dordett , CEO |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | 2ATKUAPW42 |
| Name of Grantee: | AirPatrol OU |
| Equipment Class: | Digital Transmission System |
| Notes: | Communication Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 2412.0 - 2462.0 | 0.2361 |
| Limited Modular Approval. Output power listed is Conducted(Maximum peak). Separate evaluation must be required for any portable configuration. Host systems must provide regulated supply voltages to the module. When used in mobile applications, the antennas shown in this filing must be installed to provide a separation distance of at least 20 cm from all persons. Compliance of this device in all final host configurations is the responsibility of the Grantee. OEM integrators and end-users must be provided with specific information required to satisfy RF exposure compliance for the final host device. OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. The antenna of this device must not be co-located or used in conjunction with any other antenna or transmitter. OEM integrators must be provided with antenna installation instructions. This module can only be used with a host antenna circuit trace layout design in strict compliance with the OEM instructions provided. Additional host systems will require reassessment due to the lack of voltage regulation and use special test jig board. Class II Permissive Change for a change of antenna circuit trace layout design for a specific host product as described in the filing. |
| Mail To: |