FCC ID B94-RTL8922AEK

Class II Permissive Change: Enables portable use when integrated into the HP Notebook PC, TPN-W174. The highest reported SAR for the body and simultaneous transmission use conditions are < 0.10 W/kg and 0.88 W/kg, respectively.

C2PC for adding NII-6/8 for 6GHz VLP mode with SAR evaluation for PIFA antennas as described in the filing.

Single modular approval. Power listed is maximum EIRP. This device supports 20/40/80/160 MHz bandwidth modes. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the mobile RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. For PIFA antennas, portable RF exposure compliance was evaluated at a separation distance of 5 mm and the highest reported SAR value for body and simultaneous exposure conditions are 0.25 W/kg and 0.51 W/kg respectively. The APD and IPD corresponding to the highest reported SAR are 2.18 W/m2 and 7.39 W/m2 respectively. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only the antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The host product antenna must be permanently installed and not replaceable by the end user.

Single Modular Approval. Power listed is the maximum conducted output power. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter.

Single Modular Approval. Power listed is the EIRP. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. This device has 20 MHz, 40 MHz, 80 MHz, and 160 MHz bandwidth modes. Device must compliant indoor restrictions when connected to indoor low power AP.

C2PC for enabling WLAN MRU mode through software change as described in this filing.

Single Modular Approval. Power listed is the maximum combined conducted output power. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The device supports 2x2 MIMO and has 20MHz, 40 MHz bandwidth modes.

C2PC for adding two new antenna sets as described in this filing.

Single Modular Approval. Power listed is the maximum conducted output power. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter.

C2PC for enabling WLAN MRU mode through software change as described in this filing.

Single Modular Approval. U-NII-1 through U-NII-3 Power listed are the maximum combined conducted output power, U-NII-4 and U-NII -3 & -4 span channels Power listed are EIRP. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The device supports 2x2 MIMO and has 20 MHz, 40 MHz, 80 MHz and 160 MHz bandwidth modes.

C2PC for enabling WLAN MRU mode through software change as described in this filing.

Single Modular Approval. Power listed is the EIRP. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. This device has 20 MHz, 40 MHz, 80 MHz, and 160 MHz bandwidth modes. Device must compliant indoor restrictions when connected to indoor low power AP.

C2PC for enabling WLAN MRU mode through software change as described in this filing.

Single Modular Approval. Power listed is the maximum combined conducted output power. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The device supports 2x2 MIMO and has 20MHz, 40 MHz bandwidth modes.

Single modular approval. Power listed is maximum EIRP. This device supports 20/40/80/160 MHz bandwidth modes. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the mobile RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. For PIFA antennas, portable RF exposure compliance was evaluated at a separation distance of 5 mm and the highest reported SAR value for body and simultaneous exposure conditions are 0.25 W/kg and 0.51 W/kg respectively. The APD and IPD corresponding to the highest reported SAR are 2.18 W/m2 and 7.39 W/m2 respectively. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only the antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The host product antenna must be permanently installed and not replaceable by the end user.

Single Modular Approval. U-NII-1 through U-NII-3 Power listed are the maximum combined conducted output power, U-NII-4 and U-NII -3 & -4 span channels Power listed are EIRP. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The device supports 2x2 MIMO and has 20 MHz, 40 MHz, 80 MHz and 160 MHz bandwidth modes.

C2PC for adding two new antenna sets as described in this filing.

Single Modular Approval. Power listed is the maximum conducted output power. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter.

Class II Permissive Change: Enables portable use when integrated into the HP Notebook PC, TPN-W174. The highest reported SAR for the body and simultaneous transmission use conditions are 0.56 W/kg and 0.77 W/kg, respectively.

Class II Permissive Change: Enables portable use when integrated into the HP Notebook PC, TPN-W174. The highest reported SAR for the body and simultaneous transmission use conditions are 0.29 W/kg and 0.74 W/kg, respectively.

C2PC for adding NII-6/8 for 6GHz VLP mode with SAR evaluation for PIFA antennas as described in the filing.

Single modular approval. Power listed is maximum EIRP. This device supports 20/40/80/160 MHz bandwidth modes. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the mobile RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. For PIFA antennas, portable RF exposure compliance was evaluated at a separation distance of 5 mm and the highest reported SAR value for body and simultaneous exposure conditions are 0.25 W/kg and 0.51 W/kg respectively. The APD and IPD corresponding to the highest reported SAR are 2.18 W/m2 and 7.39 W/m2 respectively. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only the antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The host product antenna must be permanently installed and not replaceable by the end user.

Class II Permissive Change: Enables portable use when integrated into the HP Notebook PC, TPN-W174. The highest reported SAR for the body and simultaneous transmission use conditions are 0.44 W/kg and 0.88 W/kg, respectively. The highest reported power density is 5.47 W/m2.

C2PC for enabling WLAN MRU mode through software change as described in this filing.

Single Modular Approval. U-NII-1 through U-NII-3 Power listed are the maximum combined conducted output power, U-NII-4 and U-NII -3 & -4 span channels Power listed are EIRP. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The device supports 2x2 MIMO and has 20 MHz, 40 MHz, 80 MHz and 160 MHz bandwidth modes.

Single Modular Approval. Power listed is the maximum combined conducted output power. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The device supports 2x2 MIMO and has 20MHz, 40 MHz bandwidth modes.

C2PC for enabling WLAN MRU mode through software change as described in this filing.

Single Modular Approval. Power listed is the EIRP. Co-transmission of this module with other transmitters requires a separate evaluation according to FCC multi-transmitter procedures. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Approval is limited to OEM installation only. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. This device has 20 MHz, 40 MHz, 80 MHz, and 160 MHz bandwidth modes. Device must compliant indoor restrictions when connected to indoor low power AP.

Class II Permissive Change: Enables portable use when integrated into the HP Notebook PC, TPN-W174. The highest reported SAR for the body and simultaneous transmission use conditions are 0.44 W/kg and 0.88 W/kg, respectively. The highest reported power density is 5.47 W/m2.