FCC ID BJI-GN1041

TCB	GRANT OF EQUIPMENT AUTHORIZATION	TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:

UL Verification Services Inc. (formerly UL CCS) 47173 Benicia Street Fremont, CA 94538

Date of Grant: 10/04/2005 Application Dated: 10/04/2005

Toshiba TEC Corporation

6-78, Minami-cho

Mishima-shi, Shizuoka-ken, 411-8520 Japan

Attention: Tatsuyuki Miura

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	BJI-GN1041
Name of Grantee:	Toshiba TEC Corporation
Equipment Class:	Digital Transmission System
Notes:	Wireless LAN
Modular Type:	Limited Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
20	15C	2412.0  -  2462.0	0.1981

In this Class II permissive change filing, device was tested in a specific multifunctional digital system as indicated in the filing. Limited modular approval. "OEM integration only" and the device cannot be sold to the General Public. Co-located transmitter operating conditions with FCC ID:CJ6UPA3232BT or FCC ID: CJ6UPA3418BT have been evaluated as described in this filing. For use in mobile RF exposure conditions, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. The only antennas approved for use with this module are those documented in the filings under this FCC ID, and must be installed in the manner specified therein. The SAR data in this filing is applicable to demonstrate compliance for a final host product only as shown in this filing. Installation of this device into other host products as portable device per section 2.1093 requirements, requires the submission of a Class II permissive change application containing data demonstrating compliance for SAR, spurious emissions, and EIRP, or new application if appropriate. Compliance of this device in all final host configurations is the responsibility of the Grantee. End-users must be provided with specific information required to satisfy RF exposure compliance for the final host device. The highest reported SAR value is 0.0205 W/kg at 100% duty factor.

20:	All electrical and mechanical devices employed for spurious radiation suppression, including any modifications made during certification testing, must be incorporated in each unit marketed.

COPY	FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION	COPY
Certification

Toshiba TEC Corporation 6-78, Minami-cho Mishima-shi, Shizuoka-ken, 411-8520 Japan

Date of Grant: 10/04/2005 Application Dated: 10/04/2005

Attention: Tatsuyuki Miura

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	BJI-GN1041
Name of Grantee:	Toshiba TEC Corporation
Equipment Class:	Digital Transmission System
Notes:	Wireless LAN
Modular Type:	Limited Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
20	15C	2412.0  -  2462.0	0.1981

In this Class II permissive change filing, device was tested in a specific multifunctional digital system as indicated in the filing. Limited modular approval. "OEM integration only" and the device cannot be sold to the General Public. Co-located transmitter operating conditions with FCC ID:CJ6UPA3232BT or FCC ID: CJ6UPA3418BT have been evaluated as described in this filing. For use in mobile RF exposure conditions, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. The only antennas approved for use with this module are those documented in the filings under this FCC ID, and must be installed in the manner specified therein. The SAR data in this filing is applicable to demonstrate compliance for a final host product only as shown in this filing. Installation of this device into other host products as portable device per section 2.1093 requirements, requires the submission of a Class II permissive change application containing data demonstrating compliance for SAR, spurious emissions, and EIRP, or new application if appropriate. Compliance of this device in all final host configurations is the responsibility of the Grantee. End-users must be provided with specific information required to satisfy RF exposure compliance for the final host device. The highest reported SAR value is 0.0205 W/kg at 100% duty factor.

20:	All electrical and mechanical devices employed for spurious radiation suppression, including any modifications made during certification testing, must be incorporated in each unit marketed.

TCB Grant - Application G9VBZ52VhuuAnpcWQzrOuw==

Mail To:

TCB	GRANT OF EQUIPMENT AUTHORIZATION	TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:

UL Verification Services Inc. (formerly UL CCS) 47173 Benicia Street Fremont, CA 94538

Date of Grant: 07/25/2005 Application Dated: 07/25/2005

Toshiba TEC Corporation

6-78, Minami-cho

Mishima-shi, Shizuoka-ken, 411-8520 Japan

Attention: Tatsuyuki Miura

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	BJI-GN1041
Name of Grantee:	Toshiba TEC Corporation
Equipment Class:	Digital Transmission System
Notes:	Wireless LAN
Modular Type:	Limited Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
	15C	2412.0  -  2462.0	0.1981

Limited Module Approval. "OEM integration only" and the device cannot be sold to the General Public. Co-located transmitter operating conditions with FCC ID:CJ6UPA3232BT or FCC ID:CJ6UPA3418BT have been evaluated as described in this filing. For use in mobile RF exposure conditions, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. The only antennas approved for use with this module are those documented in the filings under this FCC ID, and must be installed in the manner specified therein. The SAR data in this filing is applicable to demonstrate compliance for a final host product only as shown in this filing. Installation of this device into other host products as portable device per section 2.1093 requirements, requires the submission of a Class II permissive change application containing data demonstrating compliance for SAR, spurious emissions, and EIRP, or new application if appropriate. Compliance of this device in all final host configurations is the responsibility of the Grantee. End-users must be provided with specific information required to satisfy RF exposure compliance for the final host device. The highest reported SAR value is 0.0205 W/kg at 100% duty factor.

COPY	FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION	COPY
Certification

Toshiba TEC Corporation 6-78, Minami-cho Mishima-shi, Shizuoka-ken, 411-8520 Japan

Date of Grant: 07/25/2005 Application Dated: 07/25/2005

Attention: Tatsuyuki Miura

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	BJI-GN1041
Name of Grantee:	Toshiba TEC Corporation
Equipment Class:	Digital Transmission System
Notes:	Wireless LAN
Modular Type:	Limited Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
	15C	2412.0  -  2462.0	0.1981

Limited Module Approval. "OEM integration only" and the device cannot be sold to the General Public. Co-located transmitter operating conditions with FCC ID:CJ6UPA3232BT or FCC ID:CJ6UPA3418BT have been evaluated as described in this filing. For use in mobile RF exposure conditions, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. The only antennas approved for use with this module are those documented in the filings under this FCC ID, and must be installed in the manner specified therein. The SAR data in this filing is applicable to demonstrate compliance for a final host product only as shown in this filing. Installation of this device into other host products as portable device per section 2.1093 requirements, requires the submission of a Class II permissive change application containing data demonstrating compliance for SAR, spurious emissions, and EIRP, or new application if appropriate. Compliance of this device in all final host configurations is the responsibility of the Grantee. End-users must be provided with specific information required to satisfy RF exposure compliance for the final host device. The highest reported SAR value is 0.0205 W/kg at 100% duty factor.

Mail To: