FCC ID CJ6UPA3297WL

This application does not exist.

COPY	FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION	COPY
Certification

Dynabook Inc. 6-15 Toyosu 5-chome, Koto-ku Tokyo 135-8505, Japan

Date of Grant: 11/13/2003 Application Dated: 10/14/2003

Attention: Toru Kawasaki , Senior Manager

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	CJ6UPA3297WL
Name of Grantee:	Dynabook Inc.
Equipment Class:	Unlicensed National Information Infrastructure TX
Notes:	802.11a/b/g Combo Mini PCI Module
Modular Type:	Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
CE	15E	5180.0  -  5250.0	0.048
CE	15E	5250.0  -  5320.0	0.047

Modular Approval. Output power listed is conducted. Co-located transmitter operating conditions with FCC ID:CJ6UPA3232BT has been evaluated as described in this filing. For use in mobile RF exposure conditions, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. The only antennas approved for use with this module are those documented in the filings under this FCC ID, and must be installed in the manner specified therein. The grantee has to ensure the installation procedures comply with 15.407(d) integral antenna requirement which prevent the end user to access the transmitter module after the installation. This device must be installed in Toshiba laptop computers only by Toshiba or by Toshiba OEM dealers. User installation is prohibited. Use in portable RF exposure conditions is limited to the specific laptop computer configurations evaluated in this filing. The highest reported SAR value is: body 5.2 GHz, 0.26 W/kg.

CE:	This device has shown compliance with the conducted emissions limits in 15.107, 15.207, or 18.307 adopted under FCC 02-157 (ET Docket 98-80). The device may be marketed after July 11, 2005, and is not affected by the 15.37(j) or 18.123 transition provisions.

TCB Grant - Application OyNQqkuuzfUc9DZppa/x8g==

EAS Grant - Application OyNQqkuuzfUc9DZppa/x8g==

Mail To:

STEVE CHENG, EMC ENGINEERING MANAGER

COMPLIANCE CERTIFICATION SERVICES

561F MONTEREY ROAD

MORGAN HILL, CA 95037

COPY	FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION	COPY
Certification

Dynabook Inc. 6-15 Toyosu 5-chome, Koto-ku Tokyo 135-8505, Japan

Date of Grant: 11/13/2003 Application Dated: 10/14/2003

Attention: Toru Kawasaki , Senior Manager

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	CJ6UPA3297WL
Name of Grantee:	Dynabook Inc.
Equipment Class:	Digital Transmission System
Notes:	802.11a/b/g Combo Mini PCI Module
Modular Type:	Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
CE	15C	2412.0  -  2462.0	0.183
CE	15C	5745.0  -  5825.0	0.132

Modular Approval. Output power listed is conducted. Co-located transmitter operating conditions with FCC ID:CJ6UPA3232BT has been evaluated as described in this filing. For use in mobile RF exposure conditions, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. The only antennas approved for use with this module are those documented in the filings under this FCC ID, and must be installed in the manner specified therein. The grantee has to ensure the installation procedures comply with 15.407(d) integral antenna requirement which prevent the end user to access the transmitter module after the installation. This device must be installed in Toshiba laptop computers only by Toshiba or by Toshiba OEM dealers. User installation is prohibited. Use in portable RF exposure conditions is limited to the specific laptop computer configurations evaluated in this filing. The highest reported SAR values are: body 2.4 GHz, 0.43 W/kg; 5.8 GHz, 0.33 W/kg.

CE:	This device has shown compliance with the conducted emissions limits in 15.107, 15.207, or 18.307 adopted under FCC 02-157 (ET Docket 98-80). The device may be marketed after July 11, 2005, and is not affected by the 15.37(j) or 18.123 transition provisions.

TCB Grant - Application LzqUMG4M50SjydcuYqb5gQ==

Mail To:

STEVE CHENG, EMC ENGINEERING MANAGER

COMPLIANCE CERTIFICATION SERVICES

561F MONTEREY ROAD

MORGAN HILL, CA 95037

TCB	GRANT OF EQUIPMENT AUTHORIZATION	TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:

UL Verification Services Inc. (formerly UL CCS) 47173 Benicia Street Fremont, CA 94538

Date of Grant: 06/13/2003 Application Dated: 06/13/2003

Dynabook Inc.

6-15 Toyosu 5-chome, Koto-ku

Tokyo 135-8505, Japan

Attention: Toru Kawasaki , Senior Manager

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	CJ6UPA3297WL
Name of Grantee:	Dynabook Inc.
Equipment Class:	Digital Transmission System
Notes:	802.11a/b/g Mini-PCI Module
Modular Type:	Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
CE	15C	2412.0  -  2462.0	0.183
CE	15C	5745.0  -  5825.0	0.132

Modular Approval. Power Output listed is conducted. Approval is limited to OEM installation only. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. Co-located optional Bluetooth transmitter ( FCC ID:CJ6UPA3232BT ) operating conditions have been evaluated as described in this filing - separate equipment certification is needed for other co-location configurations and RF exposure conditions. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device.

CE:	This device has shown compliance with the conducted emissions limits in 15.107, 15.207, or 18.307 adopted under FCC 02-157 (ET Docket 98-80). The device may be marketed after July 11, 2005, and is not affected by the 15.37(j) or 18.123 transition provisions.

COPY	FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION	COPY
Certification

Dynabook Inc. 6-15 Toyosu 5-chome, Koto-ku Tokyo 135-8505, Japan

Date of Grant: 06/13/2003 Application Dated: 06/13/2003

Attention: Toru Kawasaki , Senior Manager

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	CJ6UPA3297WL
Name of Grantee:	Dynabook Inc.
Equipment Class:	Digital Transmission System
Notes:	802.11a/b/g Mini-PCI Module
Modular Type:	Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
CE	15C	2412.0  -  2462.0	0.183
CE	15C	5745.0  -  5825.0	0.132

Modular Approval. Power Output listed is conducted. Approval is limited to OEM installation only. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. Co-located optional Bluetooth transmitter ( FCC ID:CJ6UPA3232BT ) operating conditions have been evaluated as described in this filing - separate equipment certification is needed for other co-location configurations and RF exposure conditions. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device.

CE:	This device has shown compliance with the conducted emissions limits in 15.107, 15.207, or 18.307 adopted under FCC 02-157 (ET Docket 98-80). The device may be marketed after July 11, 2005, and is not affected by the 15.37(j) or 18.123 transition provisions.

TCB Grant - Application h2THQuF4HbrWVTuWbjteoQ==

Mail To:

TCB	GRANT OF EQUIPMENT AUTHORIZATION	TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:

UL Verification Services Inc. (formerly UL CCS) 47173 Benicia Street Fremont, CA 94538

Date of Grant: 06/13/2003 Application Dated: 06/13/2003

Dynabook Inc.

6-15 Toyosu 5-chome, Koto-ku

Tokyo 135-8505, Japan

Attention: Toru Kawasaki , Senior Manager

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	CJ6UPA3297WL
Name of Grantee:	Dynabook Inc.
Equipment Class:	Unlicensed National Information Infrastructure TX
Notes:	802.11a/b/g Mini-PCI Module
Modular Type:	Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
CE	15E	5180.0  -  5250.0	0.048
CE	15E	5250.0  -  5320.0	0.047

Modular Approval. Power Output listed is conducted. Approval is limited to OEM installation only. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. Co-located optional Bluetooth transmitter ( FCC ID:CJ6UPA3232BT ) operating conditions have been evaluated as described in this filing - separate equipment certification is needed for other co-location configurations and RF exposure conditions. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device.

CE:	This device has shown compliance with the conducted emissions limits in 15.107, 15.207, or 18.307 adopted under FCC 02-157 (ET Docket 98-80). The device may be marketed after July 11, 2005, and is not affected by the 15.37(j) or 18.123 transition provisions.

COPY	FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION	COPY
Certification

Dynabook Inc. 6-15 Toyosu 5-chome, Koto-ku Tokyo 135-8505, Japan

Date of Grant: 06/13/2003 Application Dated: 06/13/2003

Attention: Toru Kawasaki , Senior Manager

NOT TRANSFERABLE

EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.

FCC IDENTIFIER:	CJ6UPA3297WL
Name of Grantee:	Dynabook Inc.
Equipment Class:	Unlicensed National Information Infrastructure TX
Notes:	802.11a/b/g Mini-PCI Module
Modular Type:	Single Modular

Grant Notes	FCC Rule Parts	Frequency Range (MHZ)	Output Watts	Frequency Tolerance	Emission Designator
CE	15E	5180.0  -  5250.0	0.048
CE	15E	5250.0  -  5320.0	0.047

Modular Approval. Power Output listed is conducted. Approval is limited to OEM installation only. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. Co-located optional Bluetooth transmitter ( FCC ID:CJ6UPA3232BT ) operating conditions have been evaluated as described in this filing - separate equipment certification is needed for other co-location configurations and RF exposure conditions. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device.

CE:	This device has shown compliance with the conducted emissions limits in 15.107, 15.207, or 18.307 adopted under FCC 02-157 (ET Docket 98-80). The device may be marketed after July 11, 2005, and is not affected by the 15.37(j) or 18.123 transition provisions.

Mail To: