FCC ID L9N-7880

UHF TRANSCEIVER

by AES Corporation

Grantee Code: L9N   Product Code: 7880
Latest application date: 2004-07-20

FCC ID Device Details

FCC IDL9N-7880
Mirrorsfcc.id | gov | fccid.ai
Grantee CodeL9N
Product Code7880
Applicant BusinessAES Corporation 🇺🇸
Related Domains aes-intellinet.com
Equipment ClassUHF TRANSCEIVER
Test FirmSporton International, Inc.

Operating Frequencies

Frequency RangeApplication PurposeFinal Action Date
450-470 MHzOriginal Equipment2004-07-20

Exhibits

DocumentTypeAvailableFile
USERS MANUALUsers Manual2004-07-20PDF 365.7 KB
INTERNAL PHOTOSInternal Photos2004-07-20PDF 513.8 KB
EXTERNAL PHOTOSExternal Photos2004-07-20PDF 513.8 KB
ID LABEL LOCATIONID Label/Location Info2004-07-20PDF 495.6 KB
ID LABEL SAMPLEID Label/Location Info2004-07-20PDF 57.4 KB
TEST REPORTTest Report2004-07-20PDF 1.2 MB
CONFIDENTIALITY LETTERCover Letter(s)2004-07-20PDF 22.9 KB
parts listParts List/Tune Up Info2004-07-20PDF 12.4 KB
tune up infoParts List/Tune Up Info2004-07-20PDF 9.4 KB
BLOCK DIAGRAM Metadata onlyBlock DiagramPDF 285.7 KB
SCHEMATICS Metadata onlySchematicsPDF 36.1 KB
OPERATIONAL DESCRIPTION Metadata onlyOperational DescriptionPDF 180.2 KB

Application Information

Application IDrUS614+BkuJV5+emSotoyw==
Final Action Date2004-07-20
Application PurposeOriginal Equipment
Applicant FRN0006376933
Model7880
Frequency Range450-470 MHz
Equipment ClassLMS - Part 90 Location & Monitoring Transmitter
Device DescriptionUHF TRANSCEIVER
Responsible PartyMichael J Sherman, President, msherman@aes-intellinet.com , 978 535-7310
Test FirmW. Huang, Sporton International, Inc., kathylin@sporton.com.tw , 8862692468
TCB EmailTEI@TIMCOENGR.COM
TCB ScopeB2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
Short-Term ConfidentialityNo
Long-Term ConfidentialityYes
Grant DeferralNo
Modular EquipmentDoes not apply
Composite DeviceNo
Composite PartNo
Cognitive RadioNo
Authorization WaiverNo
Authorization Waiver ApprovedNo
Section 5301 CertificationYes
Related OET Knowledge DataBase InquiryNo
Grant CommentsPower output is conducted and measured at the antenna terminal. This is an OEM transmitter module approved for use in products operating as a mobile transmitting device with respect to 2.1091. MPE compliance was demonstrated with a typical antenna(s) gain as shown in the filing and must not exceed 3dBi. Final antenna installation and operating configurations of this transmitter including antenna gain and cable loss must not exceed the ERP of the configuration used for MPE compliance. Products operating with this module are required to provide a minimum separation distance of 20 cm. Grantee must coordinate with OEM integrators to ensure the end-users of products operating with this module are provided with operating instructions to satisfy RF exposure requirements. Separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and different antenna configurations.

Applications

Application IDDatePurpose
rUS614+BkuJV5+emSotoyw==2004-07-20Original Equipment

Equipment Authorization

FrequencyOutputToleranceEmissionRules
450-470 MHz0.70000005.0000000000ppm4K9F1D90.355

Grants

TCB Grant - Application rUS614+BkuJV5+emSotoyw==

TCB GRANT OF EQUIPMENT
AUTHORIZATION
TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:

  Timco Engineering, Inc.
849 NW State Road 45
Newberry, FL 32669
Date of Grant: 07/20/2004

Application Dated: 07/20/2004
AES Corporation
285 Newbury Street
Peabody, MA 01960
 
Attention: Michael Sherman , President

NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.
 
FCC IDENTIFIER:  L9N-7880
Name of Grantee:  AES Corporation
Equipment Class: Part 90 Location & Monitoring Transmitter
Notes: UHF TRANSCEIVER
Grant Notes  FCC Rule Parts Frequency
Range (MHZ)
Output
Watts
Frequency
Tolerance
Emission
Designator
90.355 450.0  -  470.0 0.7 5.0  PM 4K9F1D

Power output is conducted and measured at the antenna terminal. This is an OEM transmitter module approved for use in products operating as a mobile transmitting device with respect to 2.1091. MPE compliance was demonstrated with a typical antenna(s) gain as shown in the filing and must not exceed 3dBi. Final antenna installation and operating configurations of this transmitter including antenna gain and cable loss must not exceed the ERP of the configuration used for MPE compliance. Products operating with this module are required to provide a minimum separation distance of 20 cm. Grantee must coordinate with OEM integrators to ensure the end-users of products operating with this module are provided with operating instructions to satisfy RF exposure requirements. Separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and different antenna configurations.

EAS Grant - Application rUS614+BkuJV5+emSotoyw==

COPY FEDERAL COMMUNICATIONS
COMMISSION
WASHINGTON, D.C. 20554

GRANT OF EQUIPMENT
AUTHORIZATION
COPY
Certification

AES Corporation
285 Newbury Street
Peabody, MA 01960
United States
  Date of Grant: 07/20/2004

Application Dated: 07/20/2004
 
Attention: Michael Sherman , President

NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.
 
FCC IDENTIFIER:  L9N-7880
Name of Grantee:  AES Corporation
Equipment Class: Part 90 Location & Monitoring Transmitter
Notes: UHF TRANSCEIVER
Modular Type: Does not apply
Grant Notes  FCC Rule Parts Frequency
Range (MHZ)
Output
Watts
Frequency
Tolerance
Emission
Designator
90.355 450.0  -  470.0 0.7 5.0  PM 4K9F1D

Power output is conducted and measured at the antenna terminal. This is an OEM transmitter module approved for use in products operating as a mobile transmitting device with respect to 2.1091. MPE compliance was demonstrated with a typical antenna(s) gain as shown in the filing and must not exceed 3dBi. Final antenna installation and operating configurations of this transmitter including antenna gain and cable loss must not exceed the ERP of the configuration used for MPE compliance. Products operating with this module are required to provide a minimum separation distance of 20 cm. Grantee must coordinate with OEM integrators to ensure the end-users of products operating with this module are provided with operating instructions to satisfy RF exposure requirements. Separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and different antenna configurations.



Mail To: