FCC ID LDK102045

AIR-RM20A-A-K9

by Cisco Systems Inc

Grantee Code: LDK   Product Code: 102045
Latest application date: 2003-09-24

FCC ID Device Details

FCC IDLDK102045
Mirrorsfcc.id | gov | fccid.ai
Grantee CodeLDK
Product Code102045
Applicant BusinessCisco Systems Inc 🇺🇸
Related Domains cisco.com
Equipment ClassAIR-RM20A-A-K9
Test FirmCompliance Certification Services Inc

Operating Frequencies

Frequency RangeApplication PurposeFinal Action Date
5180-5250 MHzClass II permissive change or modification of presently authorized equipment2003-09-24
5180-5250 MHzOriginal Equipment2002-08-13

Exhibits

DocumentTypeAvailableFile
1200 AP dual mode QSG final draftUsers Manual2002-08-13PDF 796.1 KB
User Manual Draft CopyUsers Manual2002-08-13PDF 2.2 MB
ap1200 2 DraftUsers Manual2002-08-13PDF 2.5 MB
Internal PhotosInternal Photos2002-08-13PDF 300.3 KB
External PhotosExternal Photos2002-08-13PDF 161.1 KB
Label and Label LocationID Label/Location Info2002-08-13PDF 176.8 KB
Test Setup PhotosTest Setup Photos2003-09-24PDF 241.9 KB
Test PhotosTest Setup Photos2002-08-13PDF 580.2 KB
802 11 a and 802 11 b g colocated test reportTest Report2003-09-24PDF 23.8 KB
co located transmitter report for referenceTest Report2003-09-24PDF 2.8 MB
2002115 TX AND RX SPUR HARMONIC DATATest Report2002-08-13PDF 72.4 KB
Antenna SpecificationsTest Report2002-08-13PDF 309.2 KB
MPE Test Report Metadata onlyRF Exposure Info2002-08-13PDF 382.6 KB
Page 6 Update of Test Report for RF colocationTest Report2002-08-13PDF 118.5 KB
TX AND RX SPUR HARMONIC DATA FOR AP WITH OSPREYTest Report2002-08-13PDF 72.2 KB
Test ReportTest Report2002-08-13PDF 2.2 MB
Attestation LetterCover Letter(s)2002-08-13PDF 24.2 KB
Mobile JustificationAttestation Statements2002-08-13PDF 24.2 KB
Class II permissive change cover letterCover Letter(s)2003-09-24PDF 23.8 KB
2002115 Response LDK102045 081102Cover Letter(s)2002-08-13PDF 35.9 KB
Agency LetterCover Letter(s)2002-08-13PDF 181.4 KB
Confidentiality RequestCover Letter(s)2002-08-13PDF 24.3 KB
Correspondence ResponseCover Letter(s)2002-08-13PDF 35.4 KB
LDK102045 ResponseCover Letter(s)2002-08-13PDF 409.3 KB
change between old and new reportCover Letter(s)2002-08-13PDF 14.9 KB
2002115 calibration data type 9 probe 080802RF Exposure Info2002-08-13PDF 246.7 KB
Cisco 2002115 MPE Rev 2 081102RF Exposure Info2002-08-13PDF 393.8 KB
MPE report Metadata onlyRF Exposure Info2002-08-13PDF 375.4 KB
RF ExposureRF Exposure Info2002-08-13PDF 94.3 KB
calibratiion certificateRF Exposure Info2002-08-13PDF 387.5 KB
calibration data type 9 probeRF Exposure Info2002-08-13PDF 246.7 KB
Block Diagram Metadata onlyBlock DiagramPDF 28.1 KB
Antenna Schematics Metadata onlySchematicsPDF 62 KB
Schematics Metadata onlySchematicsPDF 809 KB
Operational Description Metadata onlyOperational DescriptionPDF 215.8 KB
Product Description Metadata onlyOperational DescriptionPDF 215.7 KB

Application Information

Application IDRoxvWwaqS1EYg5YKT5L3YQ==
Final Action Date2003-09-24
Application PurposeClass II permissive change or modification of presently authorized equipment
Applicant FRN0004968939
Model102045
Frequency Range5180-5250 MHz
Equipment ClassNII - Unlicensed National Information Infrastructure TX
Device DescriptionAIR-RM20A-A-K9
Responsible PartySamuel Kim, Manager, Engineering, samukim@cisco.com , 408-527-1446
AgentSteve Steve Steve, Compliance Certification Services, scheng@ccsemc.com , 408-463-0885
Test FirmSteve Cheng, Compliance Certification Services Inc, scheng@ccsemc.com , 408-463-0885
TCB Emailmkuo@ccsemc.com
TCB ScopeA4: UNII devices & low power transmitters using spread spectrum techniques
Short-Term ConfidentialityNo
Long-Term ConfidentialityNo
Grant DeferralNo
Modular EquipmentDoes not apply
Composite DeviceNo
Composite PartNo
Cognitive RadioNo
Authorization WaiverNo
Authorization Waiver ApprovedNo
Section 5301 CertificationYes
Related OET Knowledge DataBase InquiryNo
Grant CommentsClass II permissive change filing to include co-located transmitter condition with FCC ID:LDK102049. Output power is conducted. Separate RF exposure evaluation is required for any portable or co-located transmitter conditions other than as evaluated in this filing, and separate equipment certification may be needed depending on co-location configurations and RF exposure conditions. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device must be marketed for indoor use only.

Applications

Application IDDatePurpose
RoxvWwaqS1EYg5YKT5L3YQ==2003-09-24Class II permissive change or modification of presently authorized equipment
8/9MBEseNrBbml2M78svQQ==2002-08-13Original Equipment

Equipment Authorization

FrequencyOutputRulesGrant Notes
5180-5250 MHz0.02515E
5180-5250 MHz0.02515ECE
5250-5320 MHz0.03715E
5250-5320 MHz0.03715ECE

Grants

TCB Grant - Application RoxvWwaqS1EYg5YKT5L3YQ==

TCB GRANT OF EQUIPMENT
AUTHORIZATION
TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:

  UL Verification Services Inc. (formerly UL CCS)
47173 Benicia Street
Fremont, CA 94538
Date of Grant: 09/24/2003

Application Dated: 09/24/2003
Cisco Systems Inc
125 West Tasman Drive
San Jose, CA 95134-1706
 
Attention: Samuel Kim , Manager, Engineering

NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.
 
FCC IDENTIFIER:  LDK102045
Name of Grantee:  Cisco Systems Inc
Equipment Class: Unlicensed National Information Infrastructure TX
Notes: AIR-RM20A-A-K9
Grant Notes  FCC Rule Parts Frequency
Range (MHZ)
Output
Watts
Frequency
Tolerance
Emission
Designator
CE 15E 5180.0  -  5250.0 0.025  
CE 15E 5250.0  -  5320.0 0.037  

Class II permissive change filing to include co-located transmitter condition with FCC ID:LDK102049. Output power is conducted. Separate RF exposure evaluation is required for any portable or co-located transmitter conditions other than as evaluated in this filing, and separate equipment certification may be needed depending on co-location configurations and RF exposure conditions. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device must be marketed for indoor use only.

CE: This device has shown compliance with the conducted emissions limits in 15.107, 15.207, or 18.307 adopted under FCC 02-157 (ET Docket 98-80). The device may be marketed after July 11, 2005, and is not affected by the 15.37(j) or 18.123 transition provisions.

EAS Grant - Application RoxvWwaqS1EYg5YKT5L3YQ==

COPY FEDERAL COMMUNICATIONS
COMMISSION
WASHINGTON, D.C. 20554

GRANT OF EQUIPMENT
AUTHORIZATION
COPY
Certification

Cisco Systems Inc
125 West Tasman Drive
San Jose, CA 95134-1706
United States
  Date of Grant: 09/24/2003

Application Dated: 09/24/2003
 
Attention: Samuel Kim , Manager, Engineering

NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.
 
FCC IDENTIFIER:  LDK102045
Name of Grantee:  Cisco Systems Inc
Equipment Class: Unlicensed National Information Infrastructure TX
Notes: AIR-RM20A-A-K9
Modular Type: Does not apply
Grant Notes  FCC Rule Parts Frequency
Range (MHZ)
Output
Watts
Frequency
Tolerance
Emission
Designator
CE 15E 5180.0  -  5250.0 0.025  
CE 15E 5250.0  -  5320.0 0.037  

Class II permissive change filing to include co-located transmitter condition with FCC ID:LDK102049. Output power is conducted. Separate RF exposure evaluation is required for any portable or co-located transmitter conditions other than as evaluated in this filing, and separate equipment certification may be needed depending on co-location configurations and RF exposure conditions. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device must be marketed for indoor use only.


CE: This device has shown compliance with the conducted emissions limits in 15.107, 15.207, or 18.307 adopted under FCC 02-157 (ET Docket 98-80). The device may be marketed after July 11, 2005, and is not affected by the 15.37(j) or 18.123 transition provisions.

TCB Grant - Application 8/9MBEseNrBbml2M78svQQ==

This application does not exist.

EAS Grant - Application 8/9MBEseNrBbml2M78svQQ==

Mail To:
COPY FEDERAL COMMUNICATIONS
COMMISSION
WASHINGTON, D.C. 20554

GRANT OF EQUIPMENT
AUTHORIZATION
COPY
Certification

Cisco Systems Inc
125 West Tasman Drive
San Jose, CA 95134-1706
United States
  Date of Grant: 08/13/2002

Application Dated: 05/24/2002
 
Attention: Samuel Kim , Manager, Engineering

NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.
 
FCC IDENTIFIER:  LDK102045
Name of Grantee:  Cisco Systems Inc
Equipment Class: Unlicensed National Information Infrastructure TX
Notes: AIR-RM20A-A-K9
Modular Type: Does not apply
Grant Notes  FCC Rule Parts Frequency
Range (MHZ)
Output
Watts
Frequency
Tolerance
Emission
Designator
15E 5180.0  -  5250.0 0.025  
15E 5250.0  -  5320.0 0.037  

Output power is conducted. Co-located transmitter operating conditions with FCC ID LDK102042 have been evaluated as described in this filing. Separate RF exposure evaluation is required for any portable or co-located transmitter conditions other than as evaluated in this filing, and separate equipment certification may be needed depending on co-location configurations and RF exposure conditions. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.



Mail To: