FCC ID LO6-DVRS800

Class II Permissive Change to certify minimum separation distances from the Car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the users’ manual and MPE test reports, when Mobexcom DVRS 800 and Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooh and Wifi) and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexom DVR 800 and these mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to add more MPE measurements and SAR computation reports performed on MOBEXCOM DVRS 800 co-located with Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooth and Wifi) and mobile radio authorized under FCC ID: AZ492FT7089.

Class II Permissive Change to certify minimum separation distances from the Car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the users’ manual and MPE test reports, when Mobexcom DVRS 800 and Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooh and Wifi) and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexom DVR 800 and these mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to add more MPE measurements and SAR computation reports performed on MOBEXCOM DVRS 800 co-located with Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooth and Wifi) and mobile radio authorized under FCC ID: AZ492FT7089.

The maximum conducted output power is 23.5W. This device must be restricted to work related operations in an Occupational/Controlled RF exposure Environment. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration, and the exposure conditions and/or duration of their passengers and bystanders, to comply with the General Population/Uncontrolled MPE limit and requirements. A label, as described in this filing, must be displayed on the device to direct users to specific training information for meeting Occupational Exposure Requirements. Users must be provided with the training information, antenna installation and transmitter operating conditions for satisfying RF exposure compliance. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 54cm from all persons and must not exceed an antenna gain of 0 dBd. Power output is continuously variable from the value listed to 1W.

This Class II Change authorizes co-located antennas per MPE Assessment. CLASS II CHANGE: MPE compliance for specific transmitters and co-located conditions for operation with FCCID AZ492FT4870, FCCID AZ492FT4862, FCCID AZ492FT4867, and FCCID AZ492FT5823 was evaluated for passengers and bystanders configurations as shown in this class 2 permissive change filing and requires a separation distance of at least 90cm from the vehicle body and a maximum conducted output power of 10W.

This transmitter is certified to operate with the antennas and installation configurations tested for this filing, with companion mobile radio operating in push-to-talk mode with a duty factor not exceeding 50% and a maximum output power of 35W, 100W, 40W, respectively for FCCID AZ492FT5823, FCCID AZ492FT4870, and FCCID AZ492FT4862.

CLASS II CHANGE to change the frequency tolerance from 1.5 PM to 1.0 PM.

Class II Permissive Change to certify minimum separation distances from the car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the user’s manual and MPE test reports, when Mobexcom DVR 800, Motorola VHF, UHF, 700MHz and 800MHz Digital Mobile radios and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexcom DVR 800 and various mobile radios authorized under FCC ID: AZ492FT3824, AZ492FT5858, AZ492FT3821, AZ492FT4894, AZ492FT4897, AZ492FT4896, AZ492FT7037, AZ492FT7035, AZ492FT7043, AZ492FT7048, AZ492FT7044, AZ492FT4895, AZ492FT4898, AZ492FT7047 and AZ492FT4904.

The maximum conducted output power is 23.5W. This device must be restricted to work related operations in an Occupational/Controlled RF exposure Environment. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration, and the exposure conditions and/or duration of their passengers and bystanders, to comply with the General Population/Uncontrolled MPE limit and requirements. A label, as described in this filing, must be displayed on the device to direct users to specific training information for meeting Occupational Exposure Requirements. Users must be provided with the training information, antenna installation and transmitter operating conditions for satisfying RF exposure compliance. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 54cm from all persons and must not exceed an antenna gain of 0 dBd. Power output is continuously variable from the value listed to 1W.

This Class II Change authorizes co-located antennas per MPE Assessment. CLASS II CHANGE: MPE compliance for specific transmitters and co-located conditions for operation with FCCID AZ492FT4870, FCCID AZ492FT4862, FCCID AZ492FT4867, and FCCID AZ492FT5823 was evaluated for passengers and bystanders configurations as shown in this class 2 permissive change filing and requires a separation distance of at least 90cm from the vehicle body and a maximum conducted output power of 10W.

This transmitter is certified to operate with the antennas and installation configurations tested for this filing, with companion mobile radio operating in push-to-talk mode with a duty factor not exceeding 50% and a maximum output power of 35W, 100W, 40W, respectively for FCCID AZ492FT5823, FCCID AZ492FT4870, and FCCID AZ492FT4862.

CLASS II CHANGE to change the frequency tolerance from 1.5 PM to 1.0 PM.

Class II Permissive Change to certify minimum separation distances from the car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the user’s manual and MPE test reports, when Mobexcom DVR 800, Motorola VHF, UHF, 700MHz and 800MHz Digital Mobile radios and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexcom DVR 800 and various mobile radios authorized under FCC ID: AZ492FT3824, AZ492FT5858, AZ492FT3821, AZ492FT4894, AZ492FT4897, AZ492FT4896, AZ492FT7037, AZ492FT7035, AZ492FT7043, AZ492FT7048, AZ492FT7044, AZ492FT4895, AZ492FT4898, AZ492FT7047 and AZ492FT4904.

Class II Permissive Change to certify minimum separation distances from the Car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the users’ manual and MPE test reports, when Mobexcom DVRS 800 and Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooh and Wifi) and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexom DVR 800 and these mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to add more MPE measurements and SAR computation reports performed on MOBEXCOM DVRS 800 co-located with Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooth and Wifi) and mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to address RF exposure condition of MOBEXCOM DVRS 800 interfaced with, and transmitting simultaneously with Companion Mobile radio (FCC ID: AZ492FT7118), using various combinations of antennas as documented in the filing.

Class II Permissive Change for a change of the RF transistor from a through hole package to a surface mount package.

Class II permissive change to address RF exposure condition of MOBEXCOM DVRS 800 interfaced with, and transmitting simultaneously with Companion Mobile radio [FCC ID: AZ492FT3826, with either APX4500 (Model:M22KSS9PW1AN) or APX2500 (Model: M24KSS9PW1AN)], using various combinations of antennas as documented in the filing.

Class II Permissive Change to certify minimum separation distances from the Car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the users’ manual and MPE test reports, when Mobexcom DVRS 800 and Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooh and Wifi) and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexom DVR 800 and these mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to add more MPE measurements and SAR computation reports performed on MOBEXCOM DVRS 800 co-located with Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooth and Wifi) and mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to address RF exposure condition of MOBEXCOM DVRS 800 interfaced with, and transmitting simultaneously with Companion Mobile radio (FCC ID: AZ492FT7118), using various combinations of antennas as documented in the filing.

Class II Permissive Change for a change of the RF transistor from a through hole package to a surface mount package.

Class II permissive change to address RF exposure condition of MOBEXCOM DVRS 800 interfaced with, and transmitting simultaneously with Companion Mobile radio [FCC ID: AZ492FT3826, with either APX4500 (Model:M22KSS9PW1AN) or APX2500 (Model: M24KSS9PW1AN)], using various combinations of antennas as documented in the filing.

CLASS II CHANGE: MPE compliance for specific transmitters and co-located conditions for operation with FCCID AZ492FT4870, FCCID AZ492FT4862, FCCID AZ492FT4867, and FCCID AZ492FT5823 was evaluated for passengers and bystanders configurations as shown in this class 2 permissive change filing and requires a separation distance of at least 90cm from the vehicle body and a maximum conducted output power of 10W.

This transmitter is certified to operate with the antennas and installation configurations tested for this filing, with companion mobile radio operating in push-to-talk mode with a duty factor not exceeding 50% and a maximum output power of 35W, 100W, 40W, respectively for FCCID AZ492FT5823, FCCID AZ492FT4870, and FCCID AZ492FT4862.

CLASS II CHANGE to change the frequency tolerance from 1.5 PM to 1.0 PM.

CLASS II CHANGE: MPE compliance for specific transmitters and co-located conditions for operation with FCCID AZ492FT4870, FCCID AZ492FT4862, FCCID AZ492FT4867, and FCCID AZ492FT5823 was evaluated for passengers and bystanders configurations as shown in this class 2 permissive change filing and requires a separation distance of at least 90cm from the vehicle body and a maximum conducted output power of 10W.

This transmitter is certified to operate with the antennas and installation configurations tested for this filing, with companion mobile radio operating in push-to-talk mode with a duty factor not exceeding 50% and a maximum output power of 35W, 100W, 40W, respectively for FCCID AZ492FT5823, FCCID AZ492FT4870, and FCCID AZ492FT4862.

CLASS II CHANGE to change the frequency tolerance from 1.5 PM to 1.0 PM.

Class II Permissive Change to certify minimum separation distances from the Car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the users’ manual and MPE test reports, when Mobexcom DVRS 800 and Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooh and Wifi) and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexom DVR 800 and these mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to add more MPE measurements and SAR computation reports performed on MOBEXCOM DVRS 800 co-located with Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooth and Wifi) and mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to address RF exposure condition of MOBEXCOM DVRS 800 interfaced with, and transmitting simultaneously with Companion Mobile radio (FCC ID: AZ492FT7118), using various combinations of antennas as documented in the filing.

Class II Permissive Change for a change of the RF transistor from a through hole package to a surface mount package.

Class II permissive change to address RF exposure condition of MOBEXCOM DVRS 800 interfaced with, and transmitting simultaneously with Companion Mobile radio [FCC ID: AZ492FT3826, with either APX4500 (Model:M22KSS9PW1AN) or APX2500 (Model: M24KSS9PW1AN)], using various combinations of antennas as documented in the filing.

Class II Permissive to address the operation in NPSPAC band, changes of external enclosure, TNC RF connectors, mounting screws and connectivity of internal partition to enclosure as described in the filing.

Class II Permissive Change to certify minimum separation distances from the Car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the users’ manual and MPE test reports, when Mobexcom DVRS 800 and Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooh and Wifi) and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexom DVR 800 and these mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to add more MPE measurements and SAR computation reports performed on MOBEXCOM DVRS 800 co-located with Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooth and Wifi) and mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to address RF exposure condition of MOBEXCOM DVRS 800 interfaced with, and transmitting simultaneously with Companion Mobile radio (FCC ID: AZ492FT7118), using various combinations of antennas as documented in the filing.

Class II Permissive Change for a change of the RF transistor from a through hole package to a surface mount package.

Class II permissive change to address RF exposure condition of MOBEXCOM DVRS 800 interfaced with, and transmitting simultaneously with Companion Mobile radio [FCC ID: AZ492FT3826, with either APX4500 (Model:M22KSS9PW1AN) or APX2500 (Model: M24KSS9PW1AN)], using various combinations of antennas as documented in the filing.

Class II Permissive to address the operation in NPSPAC band, changes of external enclosure, TNC RF connectors, mounting screws and connectivity of internal partition to enclosure as described in the filing.

Power output is continuously variable from the value listed to 1W.

Power output is continuously variable from the value listed to 1W.

Class II Permissive Change to certify minimum separation distances from the Car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the users’ manual and MPE test reports, when Mobexcom DVRS 800 and Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooh and Wifi) and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexom DVR 800 and these mobile radio authorized under FCC ID: AZ492FT7089.

Class II Permissive Change to certify minimum separation distances from the Car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the users’ manual and MPE test reports, when Mobexcom DVRS 800 and Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooh and Wifi) and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexom DVR 800 and these mobile radio authorized under FCC ID: AZ492FT7089.

CLASS II CHANGE: MPE compliance for specific transmitters and co-located conditions for operation with FCCID AZ492FT4870, FCCID AZ492FT4862, FCCID AZ492FT4867, and FCCID AZ492FT5823 was evaluated for passengers and bystanders configurations as shown in this class 2 permissive change filing and requires a separation distance of at least 90cm from the vehicle body and a maximum conducted output power of 10W

This transmitter is certified to operate with the antennas and installation configurations tested for this filing, with companion mobile radio operating in push-to-talk mode with a duty factor not exceeding 50% and a maximum output power of 35W, 100W, 40W, respectively for FCCID AZ492FT5823, FCCID AZ492FT4870, and FCCID AZ492FT4862.

CLASS II CHANGE: MPE compliance for specific transmitters and co-located conditions for operation with FCCID AZ492FT4870, FCCID AZ492FT4862, FCCID AZ492FT4867, and FCCID AZ492FT5823 was evaluated for passengers and bystanders configurations as shown in this class 2 permissive change filing and requires a separation distance of at least 90cm from the vehicle body and a maximum conducted output power of 10W

This transmitter is certified to operate with the antennas and installation configurations tested for this filing, with companion mobile radio operating in push-to-talk mode with a duty factor not exceeding 50% and a maximum output power of 35W, 100W, 40W, respectively for FCCID AZ492FT5823, FCCID AZ492FT4870, and FCCID AZ492FT4862.

Class II Permissive Change to certify minimum separation distances from the Car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the users’ manual and MPE test reports, when Mobexcom DVRS 800 and Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooh and Wifi) and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexom DVR 800 and these mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to add more MPE measurements and SAR computation reports performed on MOBEXCOM DVRS 800 co-located with Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooth and Wifi) and mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to address RF exposure condition of MOBEXCOM DVRS 800 interfaced with, and transmitting simultaneously with Companion Mobile radio (FCC ID: AZ492FT7118), using various combinations of antennas as documented in the filing.

Class II Permissive Change to certify minimum separation distances from the Car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the users’ manual and MPE test reports, when Mobexcom DVRS 800 and Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooh and Wifi) and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexom DVR 800 and these mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to add more MPE measurements and SAR computation reports performed on MOBEXCOM DVRS 800 co-located with Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooth and Wifi) and mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to address RF exposure condition of MOBEXCOM DVRS 800 interfaced with, and transmitting simultaneously with Companion Mobile radio (FCC ID: AZ492FT7118), using various combinations of antennas as documented in the filing.

Class II Permissive Change to certify minimum separation distances from the Car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the users’ manual and MPE test reports, when Mobexcom DVRS 800 and Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooh and Wifi) and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexom DVR 800 and these mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to add more MPE measurements and SAR computation reports performed on MOBEXCOM DVRS 800 co-located with Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooth and Wifi) and mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to address RF exposure condition of MOBEXCOM DVRS 800 interfaced with, and transmitting simultaneously with Companion Mobile radio (FCC ID: AZ492FT7118), using various combinations of antennas as documented in the filing.

Class II Permissive Change for a change of the RF transistor from a through hole package to a surface mount package

Class II Permissive Change to certify minimum separation distances from the Car for bystanders, and from the DVR antenna for passengers to satisfy FCC RF Exposure requirements as specified in the users’ manual and MPE test reports, when Mobexcom DVRS 800 and Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooh and Wifi) and specific antennas are intended to be used as a package and transmits simultaneously. MPE measurements were performed on Mobexom DVR 800 and these mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to add more MPE measurements and SAR computation reports performed on MOBEXCOM DVRS 800 co-located with Motorola VHF, UHF, 700 MHz and 800 MHz digital mobile radios (with Bluetooth and Wifi) and mobile radio authorized under FCC ID: AZ492FT7089.

Class II permissive change to address RF exposure condition of MOBEXCOM DVRS 800 interfaced with, and transmitting simultaneously with Companion Mobile radio (FCC ID: AZ492FT7118), using various combinations of antennas as documented in the filing.

Class II Permissive Change for a change of the RF transistor from a through hole package to a surface mount package