FCC ID MCQ-XLRP
XLR PRO Module
by Digi International Inc
Grantee Code: MCQ Product Code: XLRP
Latest application date: 2014-05-08
FCC ID Device Details
Operating Frequencies
| Frequency Range | Application Purpose | Final Action Date |
|---|---|---|
| 909-921 MHz | Original Equipment | 2014-05-08 |
Exhibits
| Document | Type | Available | File |
|---|---|---|---|
| Manual | Users Manual | 2014-05-08 | PDF 693.8 KB |
| Int | Internal Photos | 2014-05-08 | PDF 89.2 KB |
| Ext | External Photos | 2014-05-08 | PDF 160.9 KB |
| Label Info | ID Label/Location Info | 2014-05-08 | PDF 25.2 KB |
| Setup | Test Setup Photos | 2014-05-08 | PDF 505.9 KB |
| Test report | Test Report | 2014-05-08 | PDF 2.9 MB |
| Authorization | Cover Letter(s) | 2014-05-08 | PDF 131.6 KB |
| Confid | Cover Letter(s) | 2014-05-08 | PDF 331.3 KB |
| RFx | RF Exposure Info | 2014-05-08 | PDF 27.9 KB |
| Block Metadata only | Block Diagram | PDF 24.3 KB | |
| Schema Metadata only | Schematics | PDF 580.2 KB | |
| Ops Metadata only | Operational Description | PDF 20.8 KB | |
| SDR Metadata only | SDR Software/Security Inf | PDF 1.2 MB | |
| BOM Metadata only | Parts List/Tune Up Info | PDF 573 KB |
Application Information
| Application ID | KbuiGaldIpEJ/D1u9Q4wjw== |
|---|---|
| Final Action Date | 2014-05-08 |
| Application Purpose | Original Equipment |
| Applicant FRN | 0010283307 |
| Model | XLRP |
| Frequency Range | 909-921 MHz |
| Equipment Class | DTS - Digital Transmission System |
| Device Description | XLR PRO Module |
| Responsible Party | Erik Reynolds, Director of Engineering, erik.reynolds@digi.com  , 952-912-4248 |
| Technical Contact | Bill Graff, MiCOM Labs, certification@micomlabs.com  , (925)4620304 |
| Test Firm | Gordon Hurst, MiCOM Labs, gordon_hurst@micomlabs.com , 925-462-0304 |
| TCB Email | certification@micomlabs.com |
| TCB Scope | A4: UNII devices & low power transmitters using spread spectrum techniques |
| Short-Term Confidentiality | No |
| Long-Term Confidentiality | Yes |
| Grant Deferral | No |
| Modular Equipment | Single Modular Approval |
| Composite Device | No |
| Composite Part | No |
| Cognitive Radio | Yes |
| Authorization Waiver | No |
| Authorization Waiver Approved | No |
| Section 5301 Certification | Yes |
| Related OET Knowledge DataBase Inquiry | Yes |
| Grant Comments | Power Output listed is Conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter within a device, except in accordance with accepted multi-transmitter product procedures. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. |
Applications
| Application ID | Date | Purpose |
|---|---|---|
| KbuiGaldIpEJ/D1u9Q4wjw== | 2014-05-08 | Original Equipment |
Grants
TCB Grant - Application KbuiGaldIpEJ/D1u9Q4wjw==
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
MiCOM Labs 575 Boulder Court Pleasanton, CA 94566 |
Date of Grant: 05/08/2014 Application Dated: 05/06/2014 |
| Digi International Inc |
| 9350 Excelsior Blvd. |
| Suite 700 |
| Hopkins, MN 55343 |
| Attention: Erik Reynolds , Director of Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | MCQ-XLRP |
| Name of Grantee: | Digi International Inc |
| Equipment Class: | Digital Transmission System |
| Notes: | XLR PRO Module |
| Modular Type: | Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 20 | 15C | 909.0 - 921.0 | 0.966 | ||
| 20 | 15C | 915.0 - 915.0 | 0.966 |
| Power Output listed is Conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter within a device, except in accordance with accepted multi-transmitter product procedures. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. |
| 20: | All electrical and mechanical devices employed for spurious radiation suppression, including any modifications made during certification testing, must be incorporated in each unit marketed. |
EAS Grant - Application KbuiGaldIpEJ/D1u9Q4wjw==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
Digi International Inc 9350 Excelsior Blvd. Suite 700 Hopkins, MN 55343 United States |
Date of Grant: 05/08/2014 Application Dated: 05/06/2014 |
| Attention: Erik Reynolds , Director of Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | MCQ-XLRP |
| Name of Grantee: | Digi International Inc |
| Equipment Class: | Digital Transmission System |
| Notes: | XLR PRO Module |
| Modular Type: | Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 20 | 15C | 909.0 - 921.0 | 0.966 | ||
| 20 | 15C | 915.0 - 915.0 | 0.966 |
| Power Output listed is Conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter within a device, except in accordance with accepted multi-transmitter product procedures. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. |
| 20: | All electrical and mechanical devices employed for spurious radiation suppression, including any modifications made during certification testing, must be incorporated in each unit marketed. |
| Mail To: |